(1)

In accordance with Article 12 of Directive 2014/68/EU of the European Parliament and of the Council (2), pressure equipment or assemblies referred to in Article 4(1) and (2) of that Directive which are in conformity with harmonised standards or parts thereof, the references of which have been published in the Official Journal of the European Union, are to be presumed to be in conformity with the essential safety requirements covered by those standards or parts thereof referred to in Annex I to that Directive.

(2)

By letter M/071 of 1 August 1994 the Commission made a request to the European Committee for Standardization (CEN) for drawing up, in relation to the pressure equipment, the product related standards and the standards of a horizontal nature in support of Directive 97/23/EC of the European Parliament and of the Council (3). That Directive was replaced by Directive 2014/68/EU without changing the essential safety requirements referred to in Annex I to Directive 97/23/EC.

(3)

On the basis of the request M/071 CEN, in order to reflect the state of the art, amended and revised some of the existing standards. Specifically, CEN amended standards EN ISO 4126-1:2013 for safety devices for protection against excessive pressure, EN 13445-3:2014 for unfired pressure vessels, EN 13480-1:2017 and EN 13480-6:2017 for metallic industrial piping. CEN also revised the standards series EN 10217 part 1 to 6 for welded steel tubes for pressure purposes.

(4)

The Commission together with the CEN has assessed whether those standards on the pressure equipment as amended or revised by CEN comply with the request M/071.

(5)

The standards on the pressure equipment as amended or revised by CEN satisfy the requirements which they aim to cover and which are referred to in Annex I to Directive 2014/68/EU. It is therefore appropriate to publish the references of those standards in the Official Journal of the European Union.

(6)

References of amended or revised versions of standards are to be published for the standards: EN ISO 4126-1:2013, EN 10217-1:2002, EN 10217-1:2002/A1:2005, EN 10217-2:2002, EN 10217-2:2002/A1:2005, EN 10217-3:2002, EN 10217-3:2002/A1:2005, EN 10217-4:2002, EN 10217-4:2002/A1:2005, EN 10217-5:2002, EN 10217-5:2002/A1:2005, EN 10217-6:2002,EN 10217-6:2002/A1:2005, EN 13445-3:2014, EN 13445-3:2014/A1:2015, EN 13445-3:2014/A2:2016, EN 13445-3:2014/A3:2017, EN 13445-3:2014/A4:2018, EN 13445-3:2014/A5:2018, EN 13445-3:2014/A6:2019, EN 13480-1:2017, EN 13480-6:2017.

(7)

It is therefore necessary to withdraw from the Official Journal of the European Union (4) references of the standards EN 10217-1:2002, EN 10217-1:2002/A1:2005, EN 10217-2:2002, EN 10217-2:2002/A1:2005, EN 10217-3:2002, EN 10217-3:2002/A1:2005, EN 10217-4:2002, EN 10217-4:2002/A1:2005, EN 10217-5:2002, EN 10217-5:2002/A1:2005, EN 10217-6:2002, EN 10217-6:2002/A1:2005, EN 13480-1:2017, EN 13480-6:2017, EN ISO 4126-1:2013.

(8)

In order to provide the manufacturers with sufficient time to adapt their products to the revised standards EN 10217 part 1 to 6 for welded steel tubes for pressure purposes, it is necessary to defer the withdrawal of the references to those standards.

(9)

References of harmonised standards drafted in support of Directive 2014/68/EU are published in Commission Implementing Decision (EU) 2019/1616 (5). In order to ensure that the references of harmonised standards drafted in support of Directive 2014/68/EU are listed in one act, the references of standards EN ISO 4126-1:2013, EN ISO 4126-1:2013/A2:2019; EN 10217-1:2019, EN 10217-2:2019, EN 10217-3:2019, EN 10217-4:2019, EN 10217-5:2019, EN 10217-6:2019, EN 13480-1:2017, EN 13480-1:2017/A1:2019, EN 13480-6:2017, EN 13480-6:2017/A1:2019 should be included in Annex I to that Implementing Decision, and the references to standards EN 10217-1:2002, EN 10217-1:2002/A1:2005, EN 10217-2:2002, EN 10217-2:2002/A1:2005, EN 10217-3:2002, EN 10217-3:2002/A1:2005, EN 10217-4:2002, EN 10217-4:2002/A1:2005, EN 10217-5:2002, EN 10217-5:2002/A1:2005, EN 10217-6:2002, EN 10217-6:2002/A1:2005, EN 13480-1:2017, EN 13480-6:2017, EN ISO 4126-1:2013 should be included in Annex II to that Implementing Decision.

(10)

The reference of standard EN 13445-3:2014 and the references of its amendments EN 13445-3:2014/A1:2015, EN 13445-3:2014/A2:2016, EN 13445-3:2014/A3:2017, 13445-3:2014/A4:2018, EN 13445-3:2014/A5:2018, EN 13445-3:2014/A6:2019 are included in Annex I to Implementing Decision (EU) 2019/1616. Further two amendments have been made to standard EN 13445-3:2014. It is appropriate to replace the relevant entry in that Annex, adding the references of amendments EN 13445-3:2014/A7:2019 and EN 13445-3:2014/A8:2019.

(11)

Implementing Decision (EU) 2019/1616 should therefore be amended accordingly.

(12)

Compliance with a harmonised standard confers a presumption of conformity with the corresponding essential requirements set out in Union harmonisation legislation from the date of publication of the reference of such standard in the Official Journal of the European Union. This Decision should therefore enter into force on the date of its publication,