31985L0205

Id-Direttiva tal-Kummissjoni

tat-18 ta' Frar 1985

li tadatta għall-progress tekniku d-Direttiva tal-Kunsill 71/127/KEE dwar l-approssimazzjoni tal-liġijiet ta' l-Istati Membri li għandhom x'jaqsmu ma' mirja li minnhom tista' tara fuq wara ta' vetturi bil-mutur.

(85/205/KEE)

IL-KUMMISSJONI TAL-KOMUNITAJIET EWROPEJ,

Wara li kkunsidrat it-Trattat li jistabbilixxi l-Komunità Ekonomika Ewropea,

Wara li kkunsidrat id-Direttiva tal-Kunsill 70/156/KEE tas-6 ta' Frar 1970 dwar l-approssimazzjoni tal-liġijiet ta' l-Istati Membri li għandhom x'jaqsmu ma' l-approvazzjoni tat-tip ta' vetturi bil-mutur u l-karrijiet tagħhom [1], kif l-aħħar emendata bid-Direttiva 80/1267/KEE [2], u partikolarment l-Artikolu 11 tagħha,

Wara li kkunsidrat id-Direttiva tal-Kunsill 71/127/KEE ta' l-1 ta' Marzu 1971 dwar l-approssimazzjoni tal-liġijiet ta' l-Istati Membri li għandhom x'jaqsmu ma' mirja li minnhom tista' tara fuq wara ta' vetturi bil-mutur [3], kif emendata bid-Direttiva tal-Kummissjoni 79/795/KEE [4],

Billi, fid-dawl ta' l-esperjenza miksuba u l-istat l-aktar avvanzat fil-preżent, issa huwa possibbli mhux biss li jkunu amplifikati ċerti ħtiġiet tad-Direttiva 71/127/KEE u jinġiebu aktar fil-linja mal-kondizzjonijiet attwali tat-test imma wkoll jsiru aktar strinġenti bil-għan illi titjieb is-sigurtà fit-toroq.

Billi, -preżenza fuq in-naħa tal-passeġġier tal-mirja li minnhom tista' tara fuq wara esterni fuq vetturi fil-kategoriji M1 (karozzi) u NI (vannijiet ħfief), minkejja li għadha fakultattiva, ħolqot il-ħtieġa ta' modifiki fid-disinn kemm tal-mera u kif ukoll ta' l-apparat illi jżommha sabiex ikun assigurat illi, filwaqt li jagħtu garanzija ta' l-aħjar kamp ta' viżjoni, id-dimensjonijiet tal-mezz ikunu tali li jimminimiżżaw il-vibrazzjonijiet u r-reżistenza;

Billi, fil-kas ta' kategorija N3, it-tratturi artikolati (vetturi t'oġġetti tqal), id-dispożizzjonijiet li jeżistu kienu inadekwati fir-rigward tal-kamp ta' viżjoni laterali u esterna tal-ġenb u n-naħa ta' wara tal-vettura, u billi, sabiex jirrimedjaw a għal dan in-nuqqas, ġie stabbilit illi hemm bżonn tat-twaħħil ta' mera addizzjonali li minnha tista' tara fuq wara b' angolu wiesgħa.

Billi, fil-kas tal-vetturi kollha ta' kategorija N3 (vannijiet riġidi bi jew mingħajr karru u tratturi artikulati), id-dispożizzjonijiet li jeżistu kienu inadekwati fir-rigward tal-kamp ta' viżjoni fiż-żona biswit il-ġenb ta' l-istruttura tal-kabina faċċata tas-sewwieq u, billi, biex jiġi rimedjat dan in-nuqqas, kien neċessarju li jkun meħtieġ it-twaħħil ta' mera li minnha tista' tara fuq wara ta' "prossimità mill-qrib".;

Billi l-miżuri previsti f'din id-Direttiva huma skond l-opinjoni tal-Kumitat għall-Adattament għall-Progress Tekniku tad-Direttivi dwar it-tneħħija ta' ostakoli tekniċi għall-kummerċ fis-settur ta' vetturi bil-mutur,

ADOTTAT DIN ID-DIRETTIVA:

Artikolu 1

Id-Direttiva 71/127/KEE hija hawnhekk emendata kif ġej:

1. L-Artikolu 7 huwa mibdul b'dan li ġej:

"L-Artikolu 7

1. B'effett mill-1 ta' Ottubru 1985, l-ebda Stat Membru ma jista', għal raġunijiet li għandhom x'jaqsmu ma' mirja li minnhom tista' tara fuq wara:

(a) - jirrifjuta, fir-rigward ta' tip ta' vettura bil-mutur, illi jagħti l-approvazzjoni tat-tip tal-KEE, illi joħroġ id-dokument imsemmi fit-tielet inċiż ta' l-Artikolu 10(1) tad-Direttiva 70/156/KEE, jew li jagħti approvazzjoni tat-tip nazzjonali, jew

- jipprojbixxi d-dħul fis-servizz tal-vetturi,

jekk il-mirja li minnhom tista' tara fuq wara ta' dan it-tip ta' vettura jew ta' dawn il-vetturi jkunu konformi mad-dispożizzjonijiet ta' din id-Direttiva;

(b) - jirrifjuta, fir-rigward ta' tip tal-mirja li minnhom tista' tara fuq wara, li jagħti l-approvazzjoni tat-tip tal-KEE ta' komponent jew l-approvazzjoni tat-tip nazzjonali, jekk dawn il-mirja li minnhom tista' tara fuq wara jikkonformaw mad-dispożizzjonijiet ta' din id-Direttiva, jew

- jipprojbixxi t-tqegħid fis-suq ta' mirja li minnhom tista' tara fuq wara illi għandhom il-marka ta' l-approvazzjoni tat-tip tal-KEE ta' komponent maħruġa skond il-ħtiġiet ta' din id-Direttiva.

2. B'effett mill-1 ta' Ottubru 1986 Stat Membru:

(a) - m' għandux joħroġ id-dokument imsemmi fit-tielet inċiż ta' l-Artikolu 10(1) tad-Direttiva 70/156/KEE fir-rigward ta' tip ta' vettura li l-mirja li minnhom tista' tara fuq wara tagħha mhumiex konformi mad-dispożizzjonijiet ta' dan id-Direttiva.

- jista' jirrifjuta li jagħti l-approvazzjoni tat-tip nazzjonali fir-rigward ta' tip ta' vettura illi l- mirja li minnhom tista' tara fuq wara tagħha mhumiex konformi mad-dispożizzjonijiet ta' din id-Direttiva;

(b) - m' għandux jagħti l-approvazzjoni tat-tip tal-KEE ta' komponent fir-rigward ta' tip ta' mera li minnha tista' tara fuq wara jekk din ta' l-aħħar mhix konformi mad-dispożizzjonijiet ta' din id-Direttiva,

- jista' jirrifjuta illi jagħti l-approvazzjoni tat-tip nazzjonali ta' komponent fir-rigward ta' tip ta' mera li minnha tista' tara fuq wara jekk din ta' l-aħħar mhix konformi mad-dispożizzjonijiet ta' din id-Direttiva.

3. B'effett mill-1 ta' Ottubru 1988, l-Istati Membri jistgħu jipprojbixxu d-dħul fis-servizz ta' vetturi - bl-eċċezzjoni ta' dawk imsemmija fil-punt 2.1.3 ta' l-Anness III – li l-mera li minnha tista' tara fuq wara tagħhom mhumiex konformi mad-dispożizzjonijiet ta' dan id-Direttiva.

B'effett mill-1 ta' Ottubru 1992, Stati Membri jistgħu jipprobixxu d-dħul fis-servizz ta' vetturi imsemmija fil-punt 2.1.3 ta' l-Anness III li l-mera li minnha tista' tara fuq wara tagħhom mhumiex konformi mad-dispożizzjonijiet ta' dan id-Direttiva. Jistgħu ukoll jipprojbixxu t-tqegħid fis-suq ta' mirja li minnhom tista' tara fuq wara illi m' għandhomx il-marka ta' l-approvazzjoni tat-tip ta' komponent maħruġa skond il-ħtiġiet ta' din id-Direttiva."

2. L-Annessi huma sostitwiti bl-Annessi għal din id-Direttiva.

Ir-referenzi għall-Annessi fit-test tad-Direttiva 71/127/KEE għandhom jinftehmu bħala referenzi għad-dispożizzjonijiet korrespondenti fl-Annessi ma' din id-Direttiva, kif ġej:

- il-punt 2 ta' l-Anness I jikkorrispondi ma l-Anness II,

- il-punt 2.6 ta' l-Anness I jikkorrispondi ma' l-Appendiċi 2 għall-Anness II.

Artikolu 2

L-Istati Membri għandhom idaħħlu fis-seħħ id-dispożizzjonijiet neċessarji biex jikkonformaw ma' din id-Direttiva mhux aktar tard mill-1 ta' Ottubru 1985. Huma għandhom jinformaw minnufih lill-Kummissjoni b'dan.

Artikolu 3

Din id-Direttiva hija indirizzata lill-Istati Membri.

Magħmula fi Brussel, fit-18 ta' Frar 1985.

Għall-Kummissjoni

Cockfield

Viċi-President

[1] ĠU L 42, tat-23.2.1970, p. 1.

[2] ĠU L 375, tal-31.12.1980, p. 34.

[3] ĠU L 68, tat-22.3.1971, p. 1.

[4] ĠU L 239, tat-22.9.1979, p. 1.

--------------------------------------------------

ANNEX I

DEFINITIONS

1. Rear-view mirror means any device, excluding complex optical systems such as periscopes, intended to give a clear view to the rear and side of the vehicle within the fields of vision defined in item 5 of Annex III.

2. Interior rear-view mirror means a device as defined in item 1 which can be fitted in the passenger compartment of a vehicle.

3. Exterior rear-view mirror means a device as defined in item 1 which can be mounted on the external surface of a vehicle.

4. Surveillance rear-view mirror means a rear-view mirror other than a device of the type defined in item 1 which can be fitted to the inside or outside of the vehicle in order to provide fields of vision other than those specified in item 5 of Annex III.

5. Rear-view mirror type means devices which do not differ significantly in respect of the following essential characteristics:

5.1. the dimensions and radius of curvature of the rear-view mirror's reflecting surface;

5.2. the design, shape or materials of the rear-view mirrors, including the connection with the bodywork.

6. Class of rear-view mirror means all devices having one or more common characteristics or functions. They are classified as follows:

Class I: | Interior rear-view mirrors, giving the field of vision defined in item 5.2 of Annex III. |

Classes II and III: | Main exterior rear-view mirrors, giving the fields of vision defined in item 5.3 of Annex III. |

Class IV: | Wide-angle exterior rear-view mirrors, giving the field of vision defined in item 5.4 of Annex III. |

Class V: | Close-proximity exterior rear-view mirrors, giving the field of vision defined in item 5.5 of Annex III. |

7. r means the average of the radii of curvature measured over the reflecting surface, in accordance with the method described in item 2 of Appendix 1 to this Annex.

8. The principal radii of curvature at one point on the reflecting surface (ri) means the values obtained with the apparatus defined in Appendix 1, measured on the arc of the reflecting surface passing through the centre of this surface parallel to the segment b, as defined in item 2.2.1 of Annex II and on the arc perpendicular to this segment.

9. The radius of curvature at one point on the reflecting surface (rp) means the arithmetical average of the principal radii of curvature ri and r′i i.e.:

r

=

r

+ r′

i2

10. Centre of the reflecting surface means the centroid of the visible area of the reflecting surface.

11. The radius of curvature of the constituent parts of the rear-view mirror means the radius c of the arc of the circle which most closely approximates to the curved form of the part in question.

12. The driver's ocular points means two points 65 mm apart and 635 mm vertically above point R of the driver's seat as defined in Appendix 2 to this Annex. The straight line joining these points runs perpendicular to the vertical longitudinal median plane of the vehicle. The centre of the segment joining the two ocular points is in a vertical longitudinal plane which must pass through the centre of the driver's designated seating position, as specified by the vehicle manufacturer.

13. Ambinocular vision means the total field of vision obtained by the superimposition of the monocular fields of the right eye and the left eye (see diagram below).

+++++ TIFF +++++

E | = interior rear-view mirror |

OD | = driver's eyes |

OE |

ID | = virtual monocular images |

IE |

I | = virtual ambinocular image |

A | = angle of vision of left eye |

B | = angle of vision of right eye |

C | = binocular angle of vision |

D | = ambinocular angle of vision |

14. Type of vehicle as regards rear-view mirrors means motor vehicles which are identical in respect of the following basic features:

14.1. the bodywork features which reduce the field of vision;

14.2. the coordinates of point R;

14.3. the prescribed positions and types of compulsory and (if fitted) optional rear-view mirror.

15. Vehicles of categories M1, M2, M3, N1, N2, N3 means those defined in Annex I to Directives 70/156/EEC.

--------------------------------------------------

ANNEX II

DESIGN SPECIFICATIONS AND TESTS REQUIRED FOR EEC COMPONENT TYPE-APPROVAL OF REAR-VIEW MIRRORS

1. GENERAL SPECIFICATIONS

1.1. All rear-view mirrors must be adjustable.

1.2. The edge of the reflecting surface must be enclosed in a protective housing (holder, etc.) which, on its perimeter, must have a value c greater than or equal to 2,5 mm at all points and in all directions. If the reflecting surface projects beyond the protective housing, the radius of curvature c on the edge of the projecting part must be not less than 2,5 mm and the reflecting surface must return into the protective housing under a force of 50 N applied to the point of greatest projection, relative to the protective housing, in a horizontal direction, approximately parallel to the longitudinal median plane of the vehicle.

1.3. When the rear-view mirror is mounted on a plane surface, all parts, irrespective of the adjustment position of the device, including those parts remaining attached to the support after the test provided for in 4.2, which are in potential, static contact with a sphere either 165 mm in diameter in the case of an interior rear-view mirror or 100 mm in diameter in the case of an exterior rear-view mirror, must have a radius of curvature c of not less than 2,5 mm.

1.3.1. Edges of fixing holes or recesses of which the diameter or longest diagonal is less than 12 mm are exempt from the radius requirements of item 1.3 provided that they are blunted.

1.4. The device for the attachment of rear-view mirrors to the vehicle must be so designed that a cylinder with a 50 mm radius, having as its axis the axis, or one of the axes, of pivot or rotation which ensures deflection of the rear-view mirror in the direction of impact concerned, passes through at least part of the surface to which the device is attached.

1.5. The parts of exterior rear-view mirrors referred to in items 1.2 and 1.3 which are made of a material with a Shore A hardness not exceeding 60 are exempt from the relevant provisions.

1.6. In the case of those parts of interior rear-view mirrors which are made of a material with a Shore A hardness of less than 50 and which are mounted on a rigid support, the requirements of items 1.2 and 1.3 shall only apply to the support.

2. DIMENSIONS

2.1. Interior rear-view mirrors (Class I)

The dimensions of the reflecting surface must be such that it is possible to inscribe thereon a rectangle one side of which is 4 cm and the other a cm in length, where

a = 15 cm ×

1 +

1000r

2.2. Main exterior rear-view mirrors (Classes II and III)

2.2.1. The dimensions of the reflecting surface must be such that it is possible to inscribe therein:

- a rectangle 4 cm high the base length of which, measured in centimetres, has the value a;

- a segment which is parallel to the height of the rectangle and the length of which, expressed in centimetres, has the value b.

2.2.2. The minimum values of a and b are given in the table below:

Class of rear-view mirror | Categories of vehicles for which the rear-view mirrors are designed | a | b |

II | M2, M3, N2 and N3 | 171 + 1000r | 20 |

III | M1 and N1 N3 (if the requirements of item 2.1.3 of Annex III are applicable) | 131 + 1000r | 7 |

2.3. Wide-angle exterior rear-view mirrors (Class IV)

The contours of the reflecting surface must be of simple geometric form and its dimensions such that it provides, if necessary in conjunction with a Class II exterior rear-view mirror, the field of vision specified in item 5.4 of Annex III.

2.4. Close-proximity exterior rear-view mirrors (Class V)

The contours of the reflecting surface must be of simple geometric form and its dimensions such that the mirror provides the field of vision specified in item 5.5 of Annex III.

3. REFLECTING SURFACE AND COEFFICIENTS OF REFLECTION

3.1. The reflecting surface of a rear-view mirror must be either flat or spherically convex.

3.2. Differences between the radii of curvature

3.2.1. The difference between ri or r′i and rp at each reference point must not exceed 0,15 r.

3.2.2. The difference between any of the radii of curvature (rp1, rp2 and rp3) and r must not exceed 0,15 r.

3.2.3. When r is not less than 3000 mm, the value of 0,15 r quoted in items 3.2.1 and 3.2.2 is replaced by 0,25 r.

3.3. The value of r must not be less than:

3.3.1. 1200 mm for interior rear-view mirrors (Class I) and Class III main exterior rear-view mirrors;

3.3.2. 1800 mm for Class II main exterior rear-view mirrors;

3.3.3. 400 mm for wide-angle exterior rear-view mirrors (Class IV) and close-proximity exterior rear-view mirrors (Class V).

3.4. The value of the normal coefficient of reflection, as determined according to the method described in Appendix I to this Annex, must be not less than 40 %.

If the reflecting surface has two positions (day and night) the day position must allow the colours of the signals used for road traffic to be recognized. The value of the normal coefficient of reflection in the night position must be not less than 4 %.

3.5. The reflecting surface must retain the characteristics laid down in item 3.4 in spite of prolonged exposure to adverse weather conditions in normal use.

4. TESTS

4.1. Rear-view mirrors shall be subjected to the tests described in items 4.2 and 4.3.

4.1.1. The test provided for in item 4.2 shall not be required in the case of any exterior rear-view mirror of which no part is less than 2 m from the ground, regardless of the adjustment position, when the vehicle is under a load corresponding to its maximum technically permissible weight.

This derogation also applies to the attachments of rear-view mirrors (attachment plates, arms, swivel joints, etc.) which are situated less than 2 m from the ground and which do not project beyond the overall width of the vehicle, measured in the transverse plane passing through the lowest rear-view mirror attachments or any other point forward of this plane if this configuration produces a greater overall width.

In such cases, a description specifying that the rear-view mirror must be mounted so as to conform with the abovementioned conditions for the positioning of its attachments on the vehicle must be provided.

Where advantage is taken of this derogation, the arm shall be indelibly marked with the symbol

+++++ TIFF +++++

and the type-approval certificate shall be endorsed to this effect.

4.2. Impact test

4.2.1. Description of the test rig

4.2.1.1. The test rig consists of a pendulum capable of swinging about two horizontal axes at right angles to each other, one of which is perpendicular to the plane containing the release trajectory of the pendulum.

The end of the pendulum comprises a hammer formed by a rigid sphere with a diameter of 165 ± 1 mm having a 5-mm-thick rubber covering of Shore A hardness 50.

A device is provided which permits determination of the maximum angle assumed by the arm in the plane of release.

A support firmly fixed to the structure of the pendulum serves to hold the specimens in compliance with the impact requirements specified in item 4.2.2.6.

Figure 1 below gives the dimensions of the test rig and the special design specifications.

+++++ TIFF +++++

Figure 1

4.2.1.2. The centre of percussion of the pendulum coincides with the centre of the sphere which forms the hammer. It is at a distance 1 from the axis of oscillation in the release plane which is equal to 1 m ± 5 mm. The reduced mass of the pendulum is mo = 6,8 ± 0,05 kilograms (the relationship of m to the total mass m of the pendulum and to the distance d between the centre of gravity of the pendulum and its axis of rotation is expressed in the equation:

m

= m

)

4.2.2. Description of the test

4.2.2.1. The procedure used to clamp the rear-view mirror to the support shall be that recommended by the manufacturer of the device or, where appropriate, by the vehicle manufacturer.

4.2.2.2. Positioning of the rear-view mirror for the test

4.2.2.2.1. Rear-view mirrors shall be positioned on the pendulum impact rig such that the axes which are horizontal and vertical when the rear-view mirror is installed on a vehicle in accordance with the applicant's mounting instructions are in a similar position.

4.2.2.2.2. When a rear-view mirror is adjustable with respect to the base, the test position shall be that in which any pivoting device is least likely to operate, within the limits of adjustment provided by the applicant.

4.2.2.2.3. When the rear-view mirror has a device for adjusting its distance from the base, the device must be set in the position in which the distance between the housing and the base is shortest.

4.2.2.2.4. When the reflecting surface is mobile in the housing, it shall be so adjusted that the upper corner which is furthest from the vehicle is in the position of greatest projection relative to the housing.

4.2.2.3. Except in the case of test 2 for interior rear-view mirrors (see item 4.2.2.6.1), when the pendulum is in a vertical position the horizontal and longitudinal vertical planes passing through the centre of the hammer shall pass through the centre of the reflecting surface as defined in item 10 of Annex I. The longitudinal direction of oscillation of the pendulum shall be parallel to the longitudinal median plane of the vehicle.

4.2.2.4. When, under the conditions governing adjustment laid down in items 4.2.2.1 and 4.2.2.2 parts of the rear-view mirror limit the return of the hammer, the point of impact must be displaced in a direction perpendicular to the axis of rotation or pivoting in question.

The displacement must be no greater than is strictly necessary for the execution of the test; it must be limited in such a way that:

- either the sphere delimiting the hammer remains at least tangential to the cylinder as defined in paragraph 1.4;

- or the point of contact with the hammer is located at least 10 mm from the periphery of the reflecting surface.

4.2.2.5. The test consists in allowing the hammer to fall from a height corresponding to a pendulum angle of 60° from the vertical so that the hammer strikes the rear-view mirror at the moment when the pendulum reaches the vertical position.

4.2.2.6. The rear-view mirrors are subjected to impact under the following different conditions:

4.2.2.6.1. Interior rear-view mirrors

Test 1: The points of impact shall be as defined in item 4.2.2.3. The impact must be such that the hammer strikes the rear-view mirror on the reflecting surface side.

Test 2: Point of impact on the edge of the protective housing, such that the impact produced makes an angle of 45° with the plane of the reflecting surface and is situated in the horizontal plane passing through the centre of that surface. The impact must occur on the reflecting surface side.

4.2.2.6.2. Exterior rear-view mirrors

Test 1: The point of impact shall be as defined in item 4.2.2.3 or 4.2.2.4. The impact must be such that the hammer strikes the rear-view mirror on the reflecting surface side.

Test 2: The point of impact shall be as defined in item 4.2.2.3 or 4.2.2.4. The impact must be such that the hammer strikes the rear-view mirror on the side opposite to the reflecting surface.

Where Class II or III rear-view mirrors are fixed to the same mounting as Class IV rear-view mirrors, the abovementioned tests shall be executed on the lower mirror. Nevertheless, the technical service responsible for testing may repeat one or both of these tests on the upper mirror if this is less than 2 m from the ground.

4.3. Bending test on the protective housing fixed to the stem

4.3.1. This test shall be performed on all rear-view mirrors with the exception of those in Class V.

4.3.2. Description of the test

The protective housing is placed horizontally in a device in such a way that the adjustment parts of the mounting can be clamped securely. In the direction of the greatest dimension of the housing, the end nearest to the point of fixing on the adjustment part is immobilized by means of a fixed stop 15 mm wide covering the entire width of the housing.

At the other end, a stop identical to the one described above is placed on the housing so that the specified test load can be applied to it (Figure 2).

The end of the housing opposite that at which the force is applied may be clamped instead of simply blocked, as shown in Figure 2.

Example of bending-test apparatus for rear-view mirror holders

+++++ TIFF +++++

Figure 2

4.3.3. The test load is 25 kilograms. It is applied for one minute.

5. RESULTS OF THE TEST

5.1. In the tests described in item 4.2, the pendulum must continue to swing after impact in such a way that the projection of the position assumed by the arm on the plane of release makes an angle of at least 20° with the vertical.

The accuracy of measurement of the angle shall be within ± 1 °.

5.1.1. This requirement is not applicable to rear-view mirrors stuck to the windscreen, in respect of which the requirement stipulated in item 5.2 shall apply after the test.

5.1.2. The required pendulum angle of return to the vertical is reduced from 20° to 10° for all Class II rear-view mirrors and for Class III rear-view mirrors which are fitted on the mounting normally used with Class IV rear-view mirrors.

5.2. Should the mounting of the rear-view mirror break during the tests described in item 4.2. for rear-view mirrors stuck to the windscreen, the part remaining must not project beyond the base by more than 1 cm and the configuration remaining after the test must satisfy the conditions laid down in item 1.3.

5.3. The reflecting surface must not break during the tests described in items 4.2 and 4.3. However breakage of the reflecting surface will be allowed if one of the following conditions is fulfilled:

5.3.1. the fragments of glass still adhere to the back of the housing or to a surface firmly attached to the housing; partial separation of the glass from its backing is admissible provided this does not exceed 2,5 mm on either side of the cracks. It is permissible for small splinters to become detached from the surface of the glass at the point of impact;

5.3.2. the reflecting surface is made of safety glass.

--------------------------------------------------

ANNEX III

REQUIREMENTS CONCERNING THE FITTING OF REAR-VIEW MIRRORS TO VEHICLES

1. GENERAL

1.1. Rear-view mirrors must be fitted in such a way that the mirror does not move so as significantly to change the field of vision as measured or vibrate to an extent which would cause the driver to misinterpret the nature of the image perceived.

1.2. The conditions laid down in item 1.1 must be maintained when the vehicle is moving at speeds of up to 80 % of its maximum design speed, but not exceeding 150 km/h.

2. NUMBER

2.1. Minimum number of compulsory rear-view mirrors

2.1.1. The fields of vision specified in item 5 must be provided by the minimum number of compulsory rear-view mirrors given in the following table:

Vehicle category | Interior rear-view mirrors Class I | Exterior rear-view mirrors |

Main rear-view mirrors | Wide-angle rear-view mirrors Class IV | Close-proximity rear-view mirrors Class V |

Class II | Class III |

M1 | I (see item 2.1.2) | — (see item 2.1.2.3) | I on the off-side of the vehicle (but see item 2.2.1 of this Annex) | — | — |

M2 | — | 2 (1 on the left and 1 on the right) | — | — | — (see items 2.2.2 and 3.7) |

M3 | — | 2 (1 on the left and 1 on the right) | — | — | — (see items 2.2.2 and 3.7) |

N1 | I (see item 2.1.2) | — (see item 2.1.2.3) | I on the off-side of the vehicle (but see item 2.2.1 of this Annex) | — | — |

N2 | — (see item 2.2.3) | 2 (1 on the left and 1 on the right) | — | — (see item 2.2.4) | — (see items 2.2.2 and 3.7) |

Rigid lorries with or without trailer N3 Articulated tractors | — (see item 2.2.3) | 2 (1 on the left and 1 on the right) | — | — (see item 2.2.4) | 1 (see item 3.7) |

— (see item 2.2.3) | 2 (1 on the left and 1 on the right) | — (see item 2.1.3) | 1 | 1 (see item 3.7) |

2.1.2. Nevertheless, in the case of vehicles in categories M1 and N1:

2.1.2.1. if the interior rear-view mirror does not satisfy the requirements laid down in item 5.2, a second exterior rear-view mirror must be fitted to the side of the vehicle opposite that of the compulsory rear-view mirror referred to in item 2.1.1 above;

2.1.2.2. if the interior rear-view mirror does not provide any rearward vision, its presence shall not be required;

2.1.2.3. Class II exterior rear-view mirrors are admissible.

2.1.3. Nevertheless, if the design of category N3 vehicles makes it technically impossible to obtain the fields of vision specified in items 5.3.2.2 and 5.4 when a Class IV rear-view mirror is fitted to the same mounting as a Class II rear-view mirror, the latter may be replaced by a Class III rear-view mirror.

This derogation shall apply only until 1 October 1992.

2.2. Maximum number of optional rear-view mirrors

2.2.1. In the case of vehicles of category M1 and N1, an exterior rear-view mirror may be fitted on the side of the vehicle opposite to that on which the compulsory exterior rear-view mirror referred to in item 2.1.1 is fitted.

2.2.2. A Class V exterior rear-view mirror may be fitted to vehicles in categories M2, M3 and N2.

2.2.3. An interior rear-view mirror may be fitted to vehicles in categories N2 and N3.

2.2.4. A Class IV exterior rear-view mirror may be fitted to category N2 and N3 vehicles other than articulated tractors.

2.2.5. The rear-view mirrors referred to in items 2.2.1 to 2.2.4 must satisfy the requirements of this Directive.

Nevertheless, the provisions of item 5 of this Annex shall not apply to the rear-view mirrors referred to in item 2.2.3.

2.2.6. The provisions of this Directive do not apply to the surveillance rear-view mirrors defined in item 4 of Annex I. Nevertheless, these rear-view mirrors must be mounted at least 2 m above the ground when the vehicle is under a load corresponding to its maximum permissible all-up weight.

3. POSITION

3.1. Rear-view mirrors must be so placed that the driver, when sitting on the driving seat, in a normal driving position, has a clear view of the road to the rear and side(s) of the vehicle.

3.2. Exterior rear-view mirrors shall be visible through the side windows or through the portion of the windscreen that is swept by the windscreen wiper. Nevertheless, for design reasons this provision shall not apply to exterior rear-view mirrors fitted on the right side of vehicles of categories M2 and M3 in Member States with right-hand rule of the road and on the left side of vehicles of the same categories in Member States with left-hand rule of the road.

3.3. In the case of any vehicle which is in chassis/cab form when the field of vision is measured, the minimum and maximum body widths shall be stated by the manufacturer and, if necessary, simulated by dummy headboards. All vehicles and mirror configurations taken into consideration during the tests shall be shown on the EEC type-approval certificate for a vehicle with regard to the installation of rear-view mirrors (see Appendix).

3.4. The prescribed exterior rear-view mirror on the driver's side of the vehicle must be so located that an angle of not more than 55° is formed between the vertical longitudinal median plane of the vehicle and the vertical plane passing through the centre of the rear-view mirror and through the centre of the straight line 65 mm long which joins the driver's two ocular points.

3.5. Rear-view mirrors must not project beyond the external bodywork of the vehicle substantially more than is necessary to comply with the requirements concerning fields of vision laid down in item 5.

3.6. Where the lower edge of an exterior rear-view mirror is less than 2 m above the ground when the vehicle is loaded to its maximum permissible all-up weight, this rear-view mirror must not project more than 0,20 m beyond the overall width of the vehicle measured without rear-view mirrors.

3.7. Class V rear-view mirrors shall be mounted on vehicles in such a way that, regardless of their position after adjustment, no part of these mirrors or their holders is less than 2 m from the ground when the vehicle is under a load corresponding to its maximum permissible all-up weight.

These rear-view mirrors shall not, however, be mounted on vehicles the cab height of which is such as to prevent compliance with this requirement.

3.8. Subject to the requirements of items 3.5, 3.6 and 3.7, rear-view mirrors may project beyond the permissible maximum widths of vehicles.

4. ADJUSTMENT

4.1. The interior rear-view mirror must be capable of being adjusted by the driver from his driving position.

4.2. The exterior rear-view mirror situated on the driver's side must be capable of being adjusted from inside the vehicle while the door is closed, although the window may be open. The mirror may, however, be locked in position from the outside.

4.3. The requirements of item 4.2 do not apply to exterior rear-view mirrors which, after having been knocked out of alignment, can be returned to their former position without the need for adjustment.

5. FIELDS OF VISION

5.1. General

The fields of vision defined below must apply in respect of ambinocular vision, the eyes being at the driver's ocular points as defined in item 12 of Annex I above. The fields of vision shall be determined when the vehicle is in running order as defined in item 2.6 of Annex I to Directive 70/156/EEC and is carrying in addition one front-seat passenger, the mass of the passenger being 75 kilograms ± 1 %. They must be established through windows which have a total light transmission factor of at least 70 % measured perpendicularly to the surface.

5.2. Interior rear-view mirror (Class I)

The field of vision must be such that the driver can see at least a 20-m-wide, flat, horizontal portion of the road centred on the vertical longitudinal median plane of the vehicle and extending from 60 m behind the driver's ocular points (Figure 3) to the horizon.

5.3. Main exterior rear-view mirrors (Classes II and III)

5.3.1. Left-hand exterior rear-view mirror for vehicles driven on the right of the road and right-hand exterior rear-view mirror for vehicles driven on the left of the road

5.3.1.1. The field of vision must be such that the driver can see at least a 2,50-m-wide, flat, horizontal portion of the road, which is bounded on the right (in the case of vehicles driven on the right), or on the left (in the case of vehicles driven on the left) by the plane which is parallel to the median longitudinal vertical plane passing through the outermost point of the vehicle on the left (in the case of vehicles driven on the right), or on the right (in the case of vehicles driven on the left) and extends from 10 m behind the driver's ocular points to the horizon (Figures 4 and 5).

5.3.2. Right-hand exterior rear-view mirror for vehicles driven on the right and left-hand exterior rear-view mirror for vehicles driven on the left

5.3.2.1. In the case of category M1 vehicles and category N1 vehicles having a maximum weight not exceeding 2 tonnes, the field of vision must be such that the driver can see at least a 4-m-wide flat, horizontal portion of the road which is bounded on the left (in the case of vehicles driven on the right), or on the right (in the case of vehicles driven on the left) by a plane parallel to the median longitudinal vertical plane passing through the outermost point of the vehicle on the right (in the case of vehicles driven on the right) or on the left (in the case of vehicles driven on the left) and which extends from 20 m behind the driver's ocular points to the horizon (see Figure 4).

5.3.2.2. In the case of vehicles other than those referred to in item 5.3.2.1 above, the field of vision must be such that the driver can see at least a 3,50-m-wide, flat, horizontal portion of the road, which is bounded on the left (in the case of vehicles driven on the right), or on the right (in the case of vehicles driven on the left) by a plane parallel to the median longitudinal vertical plane of the vehicle and passing through the outermost point of the vehicle on the right (in the case of vehicles driven on the right) or on the left (in the case of vehicles driven on the left) and which extends from 30 m behind the driver's ocular points to the horizon.

In addition, the road must be visible to the driver over a width of 0,75 m, from a point 4 m behind the vertical plane passing through the driver's ocular points (Figure 5).

5.4. Wide-angle exterior rear-view mirror (Class IV)

5.4.1. The field of vision must be such that the driver can see at least a 12,50-m-wide, flat, horizontal portion of the road, which is bounded on the left (in the case of vehicles driven on the right), or on the right (in the case of vehicles driven on the left) by a plane parallel to the median longitudinal vertical plane of the vehicle and passing through the outermost point of the vehicle on the right (in the case of vehicles driven on the right) or on the left (in the case of vehicles driven on the left) and which extends from at least 15 m to 25 m behind the driver's ocular points. In addition, the road must be visible to the driver over a width of 2,5 m, from a point 3 m behind the vertical plane passing through the driver's ocular points (see Figure 6).

5.5. Close-proximity exterior rear-view mirror (Class V)

The field of vision must be such that the driver can see a flat horizontal portion of the road along the side of the vehicle, bounded by the following vertical planes (see Figures 7a and 7b):

5.5.1. the plane parallel to the median longitudinal vertical plane of the vehicle which passes through a point 0,2 m beyond the outermost point of the vehicle cab on the right (in the case of vehicles driven on the right) or on the left (in the case of vehicles driven on the left);

5.5.2. in the transverse direction, the parallel plane passing at a distance of 1 m in front of the plane mentioned in item 5.5.1;

5.5.3. to the rear, the plane parallel to the vertical plane passing through the driver's ocular points and situated at a distance of 1,25 m behind that plane;

5.5.4. to the front, the plane parallel to the vertical plane passing through the driver's ocular points and situated at a distance of 1 m in front of that plane. If the vertical transverse plane passing through the leading edge of the vehicle bumper is less than 1 m in front of the vertical plane passing through the driver's ocular points, the field of vision shall be limited to that plane (see Figure 7b).

5.6. In the case of rear-view mirrors consisting of several reflecting surfaces which are either of different curvature or make an angle with each other, at least one of the reflecting surfaces must provide the field of vision and have the dimensions (see item 2.2.2 of Annex II) specified for the class to which they belong.

5.7. Obstructions

5.7.1. Interior rear-view mirror (Class I)

5.7.1.1. A reduction in the field of vision due to the presence of devices such as head-restraints, sun-visors, rear window wipers and heating elements is permissible, provided that all these devices together do not obscure more than 15 % of the specified field of vision.

5.7.1.2. The degree of obstruction is measured with the headrests adjusted to their lowest possible position and with the sun-visors folded back.

5.7.2. Exterior rear-view mirrors (Classes II, III, IV and V)

In the fields of vision specified above, obstruction due to the bodywork and some of its components, such as door handles, outline marker lights, direction indicators and the extremities of rear bumpers, as well as reflective-surface cleaning components, shall not be taken into account if they are responsible for a total obstruction of less than 10 % of the specified field of vision.

5.8. Test procedure

The field of vision shall be determined by placing powerful light sources at the ocular points and examining the light reflected on the vertical monitoring screen. Other, equivalent, methods may be used.

Interior rear-view mirror

+++++ TIFF +++++

Main exterior rear-view mirrors

Vehicle driven on the right of the road

+++++ TIFF +++++

Vehicle category M1 and category N1 not exceeding 2 tonnes in weight

+++++ TIFF +++++

Vehicles in categories other than M1 and N1 not exceeding 2 tonnes in weight

+++++ TIFF +++++

Wide-angle rear-view mirror

+++++ TIFF +++++

Close-proximity exterior rear-view mirror

--------------------------------------------------