This document is an excerpt from the EUR-Lex website
Document 32018R1003
Commission Implementing Regulation (EU) 2018/1003 of 16 July 2018 amending Implementing Regulation (EU) 2017/1152 to clarify and simplify the correlation procedure and to adapt it to changes to Regulation (EU) 2017/1151 (Text with EEA relevance.)
Commission Implementing Regulation (EU) 2018/1003 of 16 July 2018 amending Implementing Regulation (EU) 2017/1152 to clarify and simplify the correlation procedure and to adapt it to changes to Regulation (EU) 2017/1151 (Text with EEA relevance.)
Commission Implementing Regulation (EU) 2018/1003 of 16 July 2018 amending Implementing Regulation (EU) 2017/1152 to clarify and simplify the correlation procedure and to adapt it to changes to Regulation (EU) 2017/1151 (Text with EEA relevance.)
C/2018/4351
OJ L 180, 17.7.2018, p. 16–21
(BG, ES, CS, DA, DE, ET, EL, EN, FR, HR, IT, LV, LT, HU, MT, NL, PL, PT, RO, SK, SL, FI, SV)
In force
17.7.2018 |
EN |
Official Journal of the European Union |
L 180/16 |
COMMISSION IMPLEMENTING REGULATION (EU) 2018/1003
of 16 July 2018
amending Implementing Regulation (EU) 2017/1152 to clarify and simplify the correlation procedure and to adapt it to changes to Regulation (EU) 2017/1151
(Text with EEA relevance)
THE EUROPEAN COMMISSION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Regulation (EU) No 510/2011 of the European Parliament and of the Council of 11 May 2011 setting emission performance standards for new light commercial vehicles as part of the Union's integrated approach to reduce CO2 emissions from light duty vehicles (1), and in particular the third subparagraph of Article 13(6) thereof,
Whereas:
(1) |
Based on the experience gained from the implementation of Commission Regulation (EU) 2017/1151 (2) and Commission Implementing Regulation (EU) 2017/1152 (3), it has become evident that certain elements of the latter Regulation should be amended. |
(2) |
It is necessary to complement the existing method for defining the end-points of the interpolation line used for calculating the NEDC CO2 emission value of an individual vehicle. Those end-points, which are represented by a test vehicle with the highest CO2 emission values, and test vehicle with the lowest values, should be defined so that the difference between the two test vehicles high and low is equal to or higher than 5 g CO2/km. |
(3) |
In order to avoid that the CO2 emission values of individual vehicles are determined on the basis of interpolation lines that do not provide the minimum difference, it is appropriate that this amendment enters into force without delay. |
(4) |
Where for the purpose of type approval under Regulation (EU) 2017/1151, road load matrix families are used, the calculation of the NEDC CO2 emission value of an individual vehicle belonging to such a family should be simplified by deriving the road load coefficients to be used for the calculation of the NEDC CO2 value from the road load coefficients of the individual vehicle as determined under Regulation (EU) 2017/1151. |
(5) |
As regards incomplete N1 vehicles, the amendment to Annex XII to Regulation (EU) 2017/1151 should be taken into account for the purpose of the determination of the road load coefficients to be used as input to the correlation tool. |
(6) |
In order to ensure a robust correlation output, it is appropriate to add the number of cylinders as an input to be provided for the correlation tool. |
(7) |
The opportunity should also be taken to correct some editorial errors in the text. |
(8) |
The measures provided for in this Regulation are in accordance with the opinion of the Climate Change Committee, |
HAS ADOPTED THIS REGULATION:
Article 1
Annex I to Implementing Regulation (EU) 2017/1152 is amended in accordance with the Annex to this Regulation
Article 2
This Regulation shall enter into force on the seventh day following that of its publication in the Official Journal of the European Union.
This Regulation shall be binding in its entirety and directly applicable in all Member States.
Done at Brussels, 16 July 2018.
For the Commission
The President
Jean-Claude JUNCKER
(1) OJ L 145, 31.5.2011, p. 1.
(2) Commission Regulation (EU) 2017/1151 of 1 June 2017 supplementing Regulation (EC) No 715/2007 of the European Parliament and of the Council on type-approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information, amending Directive 2007/46/EC of the European Parliament and of the Council, Commission Regulation (EC) No 692/2008 and Commission Regulation (EU) No 1230/2012 and repealing Regulation (EC) No 692/2008 (OJ L 175, 7.7.2017, p. 1).
(3) Commission Implementing Regulation (EU) 2017/1152 of 2 June 2017 setting out a methodology for determining the correlation parameters necessary for reflecting the change in the regulatory test procedure with regard to light commercial vehicles and amending Implementing Regulation (EU) No 293/2012 (OJ L 175, 7.7.2017, p. 644).
ANNEX
Annex I is amended as follows:
(1) |
point 2.3.8.1 is replaced by the following: ‘2.3.8.1. In the case of WLTP road loads being determined in accordance with paragraphs 1-4 and 6 of Sub-Annex 4 to Annex XXI to Regulation (EU) 2017/1151 The NEDC road load coefficients for complete N1 vehicles shall be calculated in accordance with the formulae specified in point 2.3.8.1.1 (for vehicle H) and in point 2.3.8.1.2 (for vehicle L) and in accordance with the following points (a) and (b). Unless otherwise specified, the formulae shall apply both in the case of simulations and in the case of physical vehicle tests. The type approval authority, or where applicable, the technical service shall verify if the wind-tunnel facility referred to in paragraph 3.2.3.2.2.3 in Sub-Annex 7 to Annex XXI to Regulation (EU) 2017/1151 is qualified to accurately determine the Δ(Cd × Af) values. If the wind-tunnel facility is not qualified, the highest aerodynamic drag value shall apply for all vehicles in the family.
Point (b) shall apply for new emission type approvals granted from 1 January 2019, or from an earlier date at the manufacturer's request.’; |
(2) |
in point 2.3.8.1.1 the following is inserted as first paragraph: ‘Where this calculation procedure is used for an individual vehicle in accordance with point 4.2.1.4.2, the WLTP road loads and test mass corresponding to the NEDC individual vehicle shall be used with the influence of the optional equipment removed.’; |
(3) |
the final paragraph of point 2.3.8.1.1.(c) is replaced by the following: ‘Where the factor F*2w,H is the road load coefficient F2 determined for the WLTP test of vehicle H from which the effect of all optional equipment has been removed.’; |
(4) |
the final paragraph of point 2.3.8.1.2.(c) is replaced by the following: ‘Where the factor F*2w,L is the road load coefficient F2 determined for the WLTP test of vehicle L from which the effect of all optional equipment has been removed.’; |
(5) |
point 2.3.8.2.1.(b) is replaced by the following: ‘(b) NEDC road load coefficients where the NEDC tabulated values are not used In the case of vehicles designed for a technically permissible maximum laden mass equal to or exceeding 3 000 kg, the NEDC road load coefficients may, at the request of the manufacturer, be determined in accordance with point 2.3.8.1.’; |
(6) |
point 2.3.8.2.2 is replaced by the following: ‘2.3.8.2.2. Road load determination for incomplete N1 vehicles in accordance with point 2.2 of Annex XII to Regulation (EU) 2017/1151 In the case of an incomplete N1 vehicle where the road loads of the representative vehicle has been determined in accordance with paragraph 2.2 of Annex XII and paragraph 5.1 of Sub-Annex 4 to Annex XXI to Regulation (EU) 2017/1151, the NEDC road load to be used as input for the correlation tool simulations shall be determined as follows:
Where,
In the case of a physical vehicle testing, the test shall be performed with the NEDC chassis dynamometer coefficients for vehicle R determined in accordance with Table 3 of Annex 4a to UN/ECE Regulation No 83.’; |
(7) |
the following point 2.3.8.3(a) is added: ‘2.3.8.3(a). Extensions of emission approvals granted pursuant to Regulation (EU) 2017/1151 Where an emission approval pursuant to Regulation (EU) 2017/1151 is extended due to the addition of new vehicles to the CO2 interpolation family with NEDC CO2 emissions higher than those of vehicle H or lower than those of vehicle L, the following shall apply for the purpose of the correlation:
In the case (a), the reference CO2 emissions shall be determined without the selection referred to in points 3.1.1.2 and 3.2.6. In the case (b), or in the case the reference CO2 emissions referred to in point (a) are higher than the interpolation line, the NEDC vehicle H and L shall be determined in accordance with points 2 and 3 of this Annex. Point (a) shall apply with regard to new extensions to new types granted from 1 January 2019, or from an earlier date at the manufacturer's request.’; |
(8) |
Table 1 of point 2.4 is amended as follows:
|
(9) |
in point 3.1.1.1.(c) the point (i) is replaced by the following:
|
(10) |
in point 3.1.4 the first paragraph is replaced by the following: ‘In the case of incomplete N1 vehicles, the simulated NEDC test of the representative vehicle (vehicle RMSV) shall be performed using the correlation tool and the relevant input data as recorded in the matrix referred to in point 2.4 related to the vehicle H or L with the cycle energy demand closest to that determined for the representative vehicle in accordance with point 4.2.1.5.’; |
(11) |
in point 3.3.1 the definition set out in the last paragraph is replaced by the following:
|
(12) |
in point 3.3.2 the definition set out in the last paragraph is replaced by the following:
|
(13) |
in point 3.3.3 the definition set out in the last paragraph is replaced by the following:
|
(14) |
point 4.2.1.4 is replaced by the following: ‘4.2.1.4. Calculation of the road load for an individual vehicle in a WLTP interpolation family 4.2.1.4.1. Road load coefficients derived from NEDC vehicle H and L The road load coefficients F0,n, F1,n and F2,n for vehicles H and L determined in accordance with point 2.3.8 are referred to as F0n,H, F1n,H and F2n,H and F0n,L, F1n,L and F2n,L respectively. The road load coefficients f0n,ind, f1n,ind and f2n,ind for an individual vehicle shall be calculated in accordance with the following formula: Formula 1(a)
For new emission type approvals granted from 1 January 2019, or prior to that date, on the manufacturer's request, the road load coefficients shall be calculated in accordance with the following formula: Formula 1(b)
Or, if (TMn,H · RRn,H – TMn,L · RRn,L ) = 0, or, where applicable, (RMn,H · RRn,H – RMn,L · RRn,L ) = 0, Formula 2 shall apply: Formula 2 f 0 n,ind = F 0 n,H – ΔF0n f 1 n,ind = F 1 n,H
or, if Δ[Cd × Af]LH,n = 0, Formula 3 shall apply: Formula 3 f 2 n,ind = F 2 n,H – ΔF2n where:
4.2.1.4.2. Road load coefficients derived from WLTP road load coefficients of individual vehicles From 1 January 2019 for new type approvals, and from 1 January 2020 for all new vehicles entering into service, or prior to that date at the request of the manufacturer, the NEDC road loads for an individual vehicle shall be derived from the WLTP road load coefficients of that vehicle in any of the following cases:
The NEDC road load coefficients shall, in the cases (a) to (d), be calculated using the formulae set out in point 2.3.8.1.1, where references to vehicle H shall be considered as references to the individual vehicle. In the case (a), CO2 extrapolation may only be performed, if the difference between NEDC vehicle H and L is equal to or higher than 5 g CO2/km. The interpolation line may in that case be extrapolated by a maximum of 3 g CO2/km above the CO2 emissions of vehicle H, or below those of vehicle L. If the extrapolation exceeds 3 g CO2/km, or the difference between NEDC vehicle H and L is lower than 5 g CO2/km, the manufacturer shall determine a new interpolation line for that family in accordance with points 2 and 3 of this Annex.’; |
(15) |
point 4.2.1.6 is deleted. |