This document is an excerpt from the EUR-Lex website
Document 42010X0717(03)
Regulation No 93 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of: I. Front underrun protective devices (FUPDs) — II. Vehicles with regard to the installation of an FUPD of an approved type — III. Vehicles with regard to their front underrun protection (FUP)
Regulation No 93 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of: I. Front underrun protective devices (FUPDs) — II. Vehicles with regard to the installation of an FUPD of an approved type — III. Vehicles with regard to their front underrun protection (FUP)
Regulation No 93 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of: I. Front underrun protective devices (FUPDs) — II. Vehicles with regard to the installation of an FUPD of an approved type — III. Vehicles with regard to their front underrun protection (FUP)
OJ L 185, , pp. 56–73
(BG, ES, CS, DA, DE, ET, EL, EN, FR, IT, LV, LT, HU, MT, NL, PL, PT, RO, SK, SL, FI, SV) This document has been published in a Special Edition(s)
(HR)
In force
|
17.7.2010 |
EN |
Official Journal of the European Union |
L 185/56 |
Only the original UN/ECE texts have legal effect under international public law. The status and date of entry into force of this Regulation should be checked in the latest version of the UN/ECE status document TRANS/WP.29/343, available at:
http://www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29fdocstts.html
Regulation No 93 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of:
|
I. |
Front underrun protective devices (FUPDs) |
|
II. |
Vehicles with regard to the installation of an FUPD of an approved type |
|
III. |
Vehicles with regard to their front underrun protection (FUP) |
Date of entry into force: 27 February 1994
CONTENTS
REGULATION
|
1. |
Scope |
|
2. |
Purpose |
|
3. |
Definitions |
|
4. |
Application for approval |
Part I — Approval of front underrun protective devices (FUPDs)
|
5. |
Approval of an FUPD |
|
6. |
Requirements for FUPDs |
Part II — Approval of a vehicle with regard to the installation of an FUPD of an approved type
|
7. |
Approval of an installation of an approved FUPD |
|
8. |
Requirements for the installation of an approved FUPD |
Part III — Approval of a vehicle with regard to its front underrun protection (FUP)
|
9. |
Approval of a vehicle with FUP |
|
10. |
Requirements for a vehicle with FUP |
ANNEXES
|
Annex 1 — |
Communication concerning the approval or extension or refusal or withdrawal of approval or production definitely discontinued of a type of front underrun protection device (FUPD) pursuant to Regulation No 93 (Part I) |
|
Annex 2 — |
Communication concerning the approval or extension or refusal or withdrawal of approval or production definitely discontinued of a vehicle type with regard to the installation of a front underrun protection device (FUPD) of an approved type pursuant to Regulation No 93 (Part II) |
|
Annex 3 — |
Communication concerning the approval or extension or refusal or withdrawal of approval or production definitely discontinued of a vehicle with regard to its front underrun protection (FUP) pursuant to Regulation No 93 (Part III) |
|
Annex 4 — |
Arrangements of approval marks |
|
Annex 5 — |
Test conditions and procedures |
|
Annex 6 — |
Conformity of production and other administrative procedures |
1. SCOPE
|
1.1. |
This Regulation applies to:
|
|
1.2. |
Vehicles of categories N2 with a maximum mass not exceeding 7,5 tonnes shall comply only with the ground clearance requirement of 400 mm set out in this Regulation. |
|
1.3. |
The requirements of this Regulation do not apply to:
|
2. PURPOSE
The purpose of this Regulation is to offer effective protection for vehicles of category M1 or N1 (1) against underrunning of vehicles mentioned in paragraph 1 of this Regulation in the event of a frontal collision.
3. DEFINITIONS
|
3.1. |
For the purpose of this Regulation:
|
4. APPLICATION FOR APPROVAL
|
4.1. |
The application for approval to a Part of this Regulation shall be submitted by the manufacturer of the type (vehicle/FUPD) or his duly accredited representative. |
|
4.2. |
For each type the application shall be accompanied by:
|
|
4.3. |
Applications pursuant to satisfying Part II of this Regulation shall be accompanied by:
|
|
4.4. |
Applications pursuant to satisfying Parts II and III of this Regulation shall be accompanied by information on the vehicle type as defined in paragraph 3.1.8 |
|
4.5. |
The competent authority shall maintain the following administrative procedures according to annex 6 to cover the following:
|
PART I
APPROVAL OF FRONT UNDERRUN PROTECTIVE DEVICES (FUPDs)
5. APPROVAL OF AN FUPD
|
5.1. |
If the FUPD submitted for approval pursuant to this Regulation meets the requirements of paragraph 6 below, approval of that type of FUPD shall be granted in accordance with the arrangements contained in annex 4. |
|
5.2. |
Notice of approval, or of extension or of refusal of approval of the type of FUPD pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement which apply this Regulation, by means of a form conforming to the model in annex 1 to this Regulation. |
6. REQUIREMENTS FOR FUPDs
|
6.1. |
The FUPD shall offer adequate resistance to forces applied parallel to the longitudinal axis of the vehicle and also satisfy certain dimensional requirements. These shall be demonstrated in accordance with the test procedure and conditions specified in annex 5 to this Regulation. |
|
6.2. |
The section height of the FUPD cross-member shall not be less than 100 mm for category N2 vehicles and 120 mm for vehicles of category N3. The lateral extremities of the cross-member shall not bend to the front or have a sharp outer edge; this condition is fulfilled when the lateral extremities of the cross-member are rounded on the outside and have a radius of curvature of not less than 2,5 mm. |
|
6.3. |
The device may be so designed that its position at the front of the vehicle can be varied. In this event, there shall be a guaranteed method of securing it in the service position so that any unintentional change of position is precluded. It shall be possible for the operator to vary the position of the device by applying a force not exceeding 40 daN; |
|
6.4. |
The outermost surfaces of every front guard installation shall be essentially smooth or horizontally corrugated save that domed heads of bolts or rivets may protrude beyond the surface to a distance not exceeding 10 mm. |
PART II
APPROVAL OF A VEHICLE WITH REGARD TO THE INSTALLATION OF AN FUPD OF AN APPROVED TYPE
7. APPROVAL OF AN INSTALLATION OF AN APPROVED FUPD
|
7.1. |
If the vehicle submitted for approval pursuant to this Part of this Regulation is provided with an approved FUPD and meets the requirements of paragraph 8 below, approval of that vehicle type shall be granted in accordance with the arrangements contained in annex 4. |
|
7.2. |
Notice of approval, or of extension or of refusal of approval of the vehicle type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement which apply this Regulation, by means of a form conforming to the model in annex 2 to this Regulation. |
8. REQUIREMENTS FOR THE INSTALLATION OF AN APPROVED FUPD
|
8.1. |
The maximum mass of a vehicle type for which approval is requested shall not exceed the value indicated on the type approval communication form of each approved FUPD intended to be installed on that vehicle. |
|
8.2. |
The vehicle with the FUPD installed shall satisfy certain dimensional requirements specified in annex 5 taking into account the test conditions and information indicated on the communication document contained in annex 1 issued in respect of the FUPD. |
|
8.3. |
The FUPD shall be so fitted to the vehicle that the horizontal distance measured in the rearward direction from the foremost part of the vehicle to the front of the FUPD does not exceed 400 mm diminished by the recorded deformation (annex 1, item 9) measured at any of the points where the test forces have been applied during the type approval of the FUPD in conformity with the provisions of Part I of this Regulation and recorded in the type approval communication form (see figures 1 and 2). |
|
8.4. |
In measuring these distances, any part of the vehicle which is more than 2 m above the ground shall be excluded. |
|
8.5. |
The maximum ground clearance with respect to the underside of the FUPD shall be no more than 400 mm, as specified in paragraph 3 of annex 5, between the two points P1 in the installed condition. Outboard of each point P1 this height may be greater than 400 mm providing the underside is not above a plane passing through the underside of the FUPD directly below the point P1 and forming a slope at 15° above the horizontal (see figure 3). |
|
8.6. |
The height above the ground of the points of application of the test forces applied to the FUPD according to Part I of this Regulation and recorded in the type approval communication form (annex 1, item 8) shall not exceed 445 mm as specified in paragraph 3 of annex 5. |
|
8.7. |
The maximum ground clearance with respect to the underside of the FUPD between the two points P1 shall be no more than 450 mm taking into account their movement during the application of the test load, according to Part I. |
|
8.8. |
The width of the FUPD shall at no point exceed the width of the mudguards covering the wheels of the foremost axle nor shall it be more than 100 mm shorter on either side than the foremost axle measured at the outermost points of the tyres, excluding the bulging of the tyres close to the ground (see figure 1), or 200 mm shorter on either side, measured from the outermost points of the access steps to the driver’s cabin. |
PART III
APPROVAL OF A VEHICLE WITH REGARD TO ITS FRONT UNDERRUNPROTECTION (FUP)
9. APPROVAL OF A VEHICLE WITH FUP
|
9.1. |
If the vehicle submitted for approval pursuant to this Regulation is provided with FUP that meets the requirements of paragraph 10 below, approval of that vehicle type shall be granted in accordance with the arrangements contained in annex 4. |
|
9.2. |
Notice of approval, or of extension or of refusal of approval of the vehicle type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement which apply this Regulation, by means of a form conforming to the model in annex 3 to this Regulation. |
10. REQUIREMENTS FOR A VEHICLE WITH FUP
|
10.1. |
Any vehicle in one of the categories N2 or N3 will be deemed to satisfy the condition set out in paragraph 2 provided that the vehicle is equipped with an FUPD which has not been separately approved to Part I of this Regulation or is so designed and/or equipped at the front that, by virtue of their shape and characteristics, its component parts can be regarded as replacing the front underrun protective device. Components whose combined function satisfies the following requirements are considered to form a front underrun protective device. |
|
10.2. |
The FUP shall offer adequate resistance to forces applied parallel to the longitudinal axis of the vehicle. The FUP shall also satisfy certain dimensional requirements. These shall be demonstrated in accordance with the test procedure and conditions specified in annex 5 to this Regulation. |
|
10.3. |
For application pursuant to Part III, the section height of the FUPD cross-member (not separately approved to Part I) shall not be less than 100 mm for category N2 vehicles and 120 mm for vehicles of category N3. |
|
10.4. |
The device may be so designed that its position at the front of the vehicle can be varied. In this event, there shall be a guaranteed method of securing it in the service position so that any unintentional change of position is precluded. It shall be possible for the operator to vary the position of the device by applying a force not exceeding 40 daN; |
|
10.5. |
The FUP shall have sufficient strength that the horizontal distance measured in the rearward direction between the foremost part of the vehicle after the application of the test forces (specified in this annex) and the test ram contact surface on the vehicle does not exceed 400 mm. |
|
10.6. |
In measuring these distances, any part of the vehicle which is more than 2 m above the ground shall be excluded. |
|
10.7. |
The maximum ground clearance with respect to the underside of the FUP shall be no more than 400 mm, as specified in paragraph 2 of annex 5, between the two points P1. Outboard of each point P1 this height may be greater than 400 mm providing the underside is not above a plane passing through the underside of the FUP directly below the point P1 and forming a slope at 15° above the horizontal (see figure 3). |
|
10.8. |
The maximum ground clearance with respect to the underside of the FUP between the two points P1 shall be no more than 450 mm taking into account their movement during the application of the test load. |
|
10.9. |
The width of the FUP shall at no point exceed the width of the mudguards covering the wheels of the foremost axle nor shall it be more than 100 mm shorter on either side than the foremost axle measured at the outermost points of the tyres, excluding the bulging of the tyres close to the ground (see figure 1), or 200 mm shorter on either side, measured from the outermost points of the access steps to the driver’s cabin. |
Figure 1
FUP normally consists of a cross-member and links to the chassis or other structural members
Note: The shape of FUPD is only an example.
Figure 2
Figure 3
(1) See Consolidated Resolution on the Construction of Vehicles (R.E.3, annex 7) (TRANS/SC1/WP29/78/Amend.3).
ANNEX 4
ARRANGEMENTS OF APPROVAL MARKS
1. APPROVAL NUMBER
|
1.1. |
An approval number shall be assigned to each type approved. Its first two digits (at present 00) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another type. |
|
1.2. |
Notice of approval, or of extension or of refusal of approval of a type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement which apply this Regulation, by means of a form conforming to one of the models in annexes 1, 2 or 3 to this Regulation. |
|
1.3. |
There shall be affixed, conspicuously and in the case of a technical unit in a position where in the installed condition it is readily accessible and specified on the approval form, to every one of series conforming to a type approved under this Regulation an international approval mark consisting of:
|
|
1.4. |
If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 1.3.1 of this annex need not be repeated; in such a case the Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 1.3.1 of this annex. |
|
1.5. |
The approval mark shall be clearly legible and be indelible. |
2. ARRANGEMENTS OF APPROVAL MARKS
2.1. Model A
a ≥ 8 mm
|
2.1.1. |
The above approval mark affixed to a vehicle shows that the vehicle type concerned has, with regard to the front underrun protection in the event of a collision, been approved in the United Kingdom (E11) pursuant to Regulation No 93, Part II (installation of a front underrun protection device (FUPD) of an approved type) under approval number 002439. The first two digits of the approval number indicate that the approval was granted in accordance with the requirements of Regulation No 93, Part II in its original form. |
2.2. Model B
a ≥ 8 mm
|
2.2.1. |
The above approval mark affixed to a vehicle shows that the vehicle type concerned has been approved in the United Kingdom (E 11) pursuant to Regulation No 93, Part II and Regulation No 31 (2). The approval numbers indicate that, at the dates when the respective approvals were given, Regulation No 93 was in its original form and Regulation No 31 included the 02 series of amendments. |
(1) 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Yugoslavia, 11 for the United Kingdom, 12 for Austria, 13 for Luxembourg, 14 for Switzerland, 15 (vacant), 16 for Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24, 25 (vacant), 26 for Slovenia and 27 for Slovakia. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement concerning the Recognition of Approval for Motor Vehicle Equipment and Parts, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations to the Contracting Parties to the Agreement.
(2) The latter number is given as an example only.
ANNEX 5
TEST CONDITIONS AND PROCEDURES
1. TEST CONDITIONS FOR FUPDs
|
1.1. |
At the request of the manufacturer the test may be conducted either:
|
|
1.2. |
In the case of paragraphs 1.1.2 and 1.1.3 above the parts used to connect the FUPD to part of the vehicle chassis or to the rigid test bench shall be equivalent to those which are used to secure the FUPD when it is installed on the vehicle. |
|
1.3. |
At the request of the manufacturer and with the consent of the technical service the test procedure described in paragraph 3 below may be simulated by calculation or another such method provided that its equivalence is demonstrated. |
2. TEST CONDITIONS FOR VEHICLES
|
2.1. |
The vehicle may, if necessary to achieve the test forces required in paragraph 3.1 below, be restrained by any method, this method to be specified by the vehicle manufacturer. |
|
2.2. |
Dimensions shall be taken as if the vehicle were in the following condition:
|
3. TEST PROCEDURE
|
3.1. |
Points P1 are located up to 200 mm from the longitudinal planes tangential to the outermost points of the tyres on the front axle, excluding the bulging of the tyres close to the ground; points P2 are symmetrical to the median longitudinal plane of the vehicle at a distance from each other of 700 to 1 200 mm inclusive. The exact positions shall be specified by the manufacturer. |
|
3.2. |
The height above the ground of points P1 and P2 shall be defined by the vehicle manufacturer within the lines that bound the front face of the device. The height shall not, however, exceed 445 mm when the vehicle is unladen. P3 is in the vertical longitudinal median plane of the vehicle (see figure 1 of the Regulation). |
|
3.3. |
The test forces set out below shall be applied to each of the test points in separate tests on the same vehicle or device or, if requested by the manufacturer/agent, on different vehicles or device samples.
|
|
3.4. |
The maximum horizontal and vertical displacements of each test point during the application of the above forces shall be recorded and the highest recorded on the communication document. |
|
3.5. |
Whenever a practical test is performed to verify compliance with the above-mentioned requirements, the following conditions shall be fulfilled:
|
ANNEX 6
Conformity of production and other administrative procedures
1. CONFORMITY OF PRODUCTION
|
1.1. |
FUPDs and vehicles approved to this Regulation shall be so manufactured as to conform to the type approval by meeting the requirements set forth in this Regulation. |
|
1.2. |
In order to verify that the requirements of paragraph 1.1 above are met, suitable controls of the production shall be carried out. |
|
1.3. |
The holder of the approval shall in particular:
|
|
1.4. |
The competent authority which has granted type-approval may at any time verify the conformity control methods applicable to each production unit.
|
2. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
|
2.1. |
The approval granted in respect of a type of FUPD or vehicle pursuant to this Regulation may be withdrawn if the requirements set forth above are not met or if the protective device has failed to pass the test prescribed in this Regulation. |
|
2.2. |
If a Contracting Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith so notify the other Contracting Parties applying this Regulation, by means of a communication form conforming to the model in annexes 1, 2 or 3 to this Regulation. |
3. MODIFICATION AND EXTENSION OF APPROVAL
|
3.1. |
Every modification of a type of FUPD or vehicle shall be notified to the administrative department which approved the type. The department may then either:
|
|
3.2. |
Confirmation or refusal of approval, specifying the alterations shall be communicated by means of a form conforming to the model in annexes 1, 2 or 3 to this Regulation to the Parties to the Agreement applying this Regulation. |
|
3.3. |
The competent authority issuing the extension of approval shall assign a series number to such an extension and inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in annexes 1, 2 or 3 to this Regulation. |
4. PRODUCTION DEFINITELY DISCONTINUED
If the holder of the approval completely ceases to manufacture a type of FUPD or vehicle FUP approved in accordance with this Regulation, he shall so inform the authority which granted the approval. Upon receiving the relevant communication that authority shall inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in annexes 1, 2 or 3 to this Regulation.
5. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF ADMINISTRATIVE DEPARTMENTS
The Contracting Parties to the 1958 Agreement applying this Regulation shall communicate to the United Nations Secretariat the names and addresses of the technical services responsible for conducting approval tests and of the administrative departments which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, or production definitely discontinued, issued in other countries, are to be sent.