This document is an excerpt from the EUR-Lex website
Document 32016R0799R(01)
Corrigendum to Commission Implementing Regulation (EU) 2016/799 of 18 March 2016 implementing Regulation (EU) No 165/2014 of the European Parliament and of the Council laying down the requirements for the construction, testing, installation, operation and repair of tachographs and their components (OJ L 139, 26.5.2016)
Corrigendum to Commission Implementing Regulation (EU) 2016/799 of 18 March 2016 implementing Regulation (EU) No 165/2014 of the European Parliament and of the Council laying down the requirements for the construction, testing, installation, operation and repair of tachographs and their components (OJ L 139, 26.5.2016)
Corrigendum to Commission Implementing Regulation (EU) 2016/799 of 18 March 2016 implementing Regulation (EU) No 165/2014 of the European Parliament and of the Council laying down the requirements for the construction, testing, installation, operation and repair of tachographs and their components (OJ L 139, 26.5.2016)
OJ L 146, 3.6.2016, p. 31–36
(BG, ES, CS, DA, DE, ET, EL, EN, FR, HR, IT, LV, LT, HU, MT, NL, PL, PT, RO, SK, SL, FI, SV)
ELI: http://data.europa.eu/eli/reg_impl/2016/799/corrigendum/2016-06-03/oj
|
3.6.2016 |
EN |
Official Journal of the European Union |
L 146/31 |
Corrigendum to Commission Implementing Regulation (EU) 2016/799 of 18 March 2016 implementing Regulation (EU) No 165/2014 of the European Parliament and of the Council laying down the requirements for the construction, testing, installation, operation and repair of tachographs and their components
( Official Journal of the European Union L 139 of 26 May 2016 )
Annex II is inserted as follows:
‘ANNEX II
APPROVAL MARK AND CERTIFICATE
I. APPROVAL MARK
|
1. |
The approval mark shall be made up of:
|
|
2. |
The approval mark shall be shown on the descriptive plaque of each set of equipment and on each record sheet and on each tachograph card. It must be indelible and must always remain clearly legible. |
|
3. |
The dimensions of the approval mark drawn below (1) are expressed in millimetres, these dimensions being minima. The ratios between the dimensions must be maintained.
|
II. APPROVAL CERTIFICATE FOR ANALOGUE TACHOGRAPHS
A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.
APPROVAL CERTIFICATE
Name of competent administration …
Notification concerning (2):
|
— |
approval of a type of recording equipment |
|
— |
withdrawal of approval of a type of recording equipment |
|
— |
approval of a model record sheet |
|
— |
withdrawal of approval of a model record sheet |
Approval No:
….
|
1. |
Trade mark or name … |
|
2. |
Name of type or model … |
|
3. |
Name of manufacturer … |
|
4. |
Address of manufacturer … |
|
5. |
Submitted for approval on … |
|
6. |
Tested at … |
|
7. |
Date and number of the test(s) … |
|
8. |
Date of approval … |
|
9. |
Date of withdrawal of approval … |
|
10. |
Type or types of recording equipment in which sheet is designed to be used |
|
11. |
Place … |
|
12. |
Date … |
|
13. |
Descriptive documents annexed … |
|
14. |
Remarks (including the position of seals if applicable) |
(Signature)
III. APPROVAL CERTIFICATE FOR DIGITAL TACHOGRAPHS
A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.
APPROVAL CERTIFICATE FOR DIGITAL TACHOGRAPHS
Name of competent administration …
Notification concerning (3):
|
☐ |
approval of: |
|
☐ |
withdrawal of approval of: |
|
☐ |
recording equipment model |
|
☐ |
recording equipment component (4) |
|
☐ |
a driver's card |
|
☐ |
a workshop card |
|
☐ |
a company card |
|
☐ |
a controller's card |
Approval No:
….
|
1. |
Manufacturing brand or trademark … |
|
2. |
Name of model … |
|
3. |
Name of manufacturer … |
|
4. |
Address of manufacturer … |
|
5. |
Submitted for approval for … |
|
6. |
Laboratory(-ies) … |
|
7. |
Date and number of test report … |
|
8. |
Date of approval … |
|
9. |
Date of withdrawal of approval … |
|
10. |
Model of recording equipment(s) with which the component is designed to be used |
|
11. |
Place … |
|
12. |
Date … |
|
13. |
Descriptive documents annexed … |
|
14. |
Remarks (including the position of seals if applicable) |
(Signature)
IV. APPROVAL CERTIFICATE FOR SMART TACHOGRAPHS
A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.
APPROVAL CERTIFICATE FOR SMART TACHOGRAPHS
Name of competent administration …
Notification concerning (5):
|
☐ |
approval of: |
|
☐ |
withdrawal of approval of: |
|
☐ |
recording equipment model |
|
☐ |
recording equipment component (6) |
|
☐ |
a driver's card |
|
☐ |
a workshop card |
|
☐ |
a company card |
|
☐ |
a controller's card |
Approval No:
….
|
1. |
Manufacturing brand or trademark … |
|
2. |
Name of model … |
|
3. |
Name of manufacturer … |
|
4. |
Address of manufacturer … |
|
5. |
Submitted for approval for … |
|
6. |
|
|
7. |
|
|
8. |
Date of approval … |
|
9. |
Date of withdrawal of approval … |
|
10. |
Model of recording equipment(s) with which the component is designed to be used |
|
11. |
Place … |
|
12. |
Date … |
|
13. |
Descriptive documents annexed … |
|
14. |
Remarks (including the position of seals if applicable) |
(Signature)
(1) These figures are shown for guidance only.
(2) Delete items not applicable.
(3) Tick the relevant boxes.
(4) Specify the component dealt with in the notification.
(5) Tick the relevant boxes.
(6) Specify the component dealt with in the notification.’