This document is an excerpt from the EUR-Lex website
Document 02023D2723-20240424
Commission Implementing Decision (EU) 2023/2723 of 6 December 2023 on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council (Text with EEA relevance)Text with EEA relevance
Consolidated text: Commission Implementing Decision (EU) 2023/2723 of 6 December 2023 on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council (Text with EEA relevance)Text with EEA relevance
Commission Implementing Decision (EU) 2023/2723 of 6 December 2023 on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council (Text with EEA relevance)Text with EEA relevance
ELI: http://data.europa.eu/eli/dec_impl/2023/2723/2024-04-24
This consolidated text may not include the following amendments:
| Amending act | Amendment type | Subdivision concerned | Date of effect |
|---|---|---|---|
| 32024D1198 | Modified by | annex I point 301 | 24/10/2025 |
| 32024D1198 | Modified by | annex I point 359 | 24/10/2025 |
| 32024D1198 | Modified by | annex I point 302 | 24/10/2025 |
| 32024D1198 | Modified by | annex I point 299 | 24/10/2025 |
| 32024D1198 | Modified by | annex I point 461 | 24/10/2025 |
| 32024D1198 | Modified by | annex I point 371 | 24/10/2025 |
02023D2723 — EN — 24.04.2024 — 001.001
This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document
|
COMMISSION IMPLEMENTING DECISION (EU) 2023/2723 of 6 December 2023 on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council (OJ L 2723 13.12.2023, p. 1) |
Amended by:
|
|
|
Official Journal |
||
|
No |
page |
date |
||
|
COMMISSION IMPLEMENTING DECISION (EU) 2024/1198 of 19 April 2024 |
L 1198 |
1 |
23.4.2024 |
|
COMMISSION IMPLEMENTING DECISION (EU) 2023/2723
of 6 December 2023
on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council
(Text with EEA relevance)
Article 1
The references to harmonised standards for electrical equipment designed for use within certain voltage limits drafted in support of Directive 2014/35/EU, listed in Annex I to this Decision, are hereby published in the Official Journal of the European Union.
Article 2
Implementing Decision (EU) 2019/1956 is repealed.
However, it shall continue to apply in respect of the reference of harmonised standard listed in Annex II to this Decision until the date of withdrawal of that reference set out in that Annex.
Article 3
Communication 2018/C 326/02 is repealed.
However, it shall continue to apply in respect of the references of harmonised standards listed in Annex III to this Decision until the dates of withdrawal of those references set out in that Annex.
Article 4
This Decision shall enter into force on the day of its publication in the Official Journal of the European Union.
ANNEX I
|
No |
Reference of the standard |
|
1. |
HD 308 S2:2001 Identification of cores in cables and flexible cords |
|
2. |
HD 368 S1:1978 Direct acting recording electrical measuring instruments and their accessories |
|
3. |
HD 549 S1:1989 Conference systems – Electrical and audio requirements |
|
4. |
HD 597 S1:1992 Coupling capacitors and capacitor dividers HD 597 S1:1992/AC:1992 |
|
5. |
HD 603 S1:1994 Distribution cables of rated voltage 0,6/1 kV HD 603 S1:1994/A3:2007 HD 603 S1:1994/A1:1997 HD 603 S1:1994/A2:2003 |
|
6. |
HD 604 S1:1994 0,6/1 kV and 1,9/3,3 kV power cables with special fire performance for use in power stations HD 604 S1:1994/A3:2005 HD 604 S1:1994/A1:1997 HD 604 S1:1994/A2:2002 |
|
7. |
HD 626 S1:1996 Overhead distribution cables of rated voltage Uo/U(Um): 0,6/1 (1,2) kV HD 626 S1:1996/A1:1997 HD 626 S1:1996/A2:2002 |
|
8. |
HD 627 S1:1996 Multicore and multipair cables for installation above and below ground HD 627 S1:1996/A1:2000 HD 627 S1:1996/A2:2005 |
|
9. |
HD 639 S1:2002 Electrical accessories – Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs) HD 639 S1:2002/A1:2003 HD 639 S1:2002/A2:2010 HD 639 S1:2002/AC:2003 |
|
10. |
EN ISO 11252:2013 Lasers and laser-related equipment – Laser device – Minimum requirements for documentation (ISO 11252:2013) |
|
11. |
EN 13637:2015 Building hardware – Electrically controlled exit systems for use on escape routes – Requirements and test methods |
|
12. |
EN 50065-4-2:2001 Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz – Part 4-2: Low voltage decoupling filters – Safety requirements EN 50065-4-2:2001/A1:2003 EN 50065-4-2:2001/A2:2005 |
|
13. |
EN 50065-4-7:2005 Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz – Part 4-7: Portable low voltage decoupling filters – Safety requirements EN 50065-4-7:2005/AC:2006 |
|
14. |
EN 50085-1:2005 Cable trunking systems and cable ducting systems for electrical installations – Part 1: General requirements EN 50085-1:2005/A1:2013 |
|
15. |
EN 50085-2-1:2006 Cable trunking systems and cable ducting systems for electrical installations – Part 2-1: Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings EN 50085-2-1:2006/A1:2011 |
|
16. |
EN 50085-2-2:2008 Cable trunking systems and cable ducting systems for electrical installations – Part 2-2: Particular requirements for cable trunking systems and cable ducting systems intended for mounting underfloor, flushfloor, or onfloor |
|
17. |
EN 50085-2-3:2010 Cable trunking systems and cable ducting systems for electrical installations – Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets |
|
18. |
EN 50085-2-4:2009 Cable trunking systems and cable ducting systems for electrical installations – Part 2-4: Particular requirements for service poles and service posts |
|
19. |
EN 50106:2008 Safety of household and similar electrical appliances – Particular rules for routine tests referring to appliances under the scope of EN 60335-1 |
|
20. |
EN 50117-1:2002 Coaxial cables – Part 1: Generic specification EN 50117-1:2002/A1:2006 EN 50117-1:2002/A2:2013 |
|
21. |
EN 50117-2-1:2005 Coaxial cables – Part 2-1: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 1 000 MHz EN 50117-2-1:2005/A1:2008 EN 50117-2-1:2005/A2:2013 |
|
22. |
EN 50117-2-2:2004 Coaxial cables – Part 2-2: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 1 000 MHz EN 50117-2-2:2004/A1:2008 EN 50117-2-2:2004/A2:2013 |
|
23. |
EN 50117-2-3:2004 Coaxial cables – Part 2-3: Sectional specification for cables used in cabled distribution networks – Distribution and trunk cables for systems operating at 5 MHz – 1 000 MHz EN 50117-2-3:2004/A1:2008 EN 50117-2-3:2004/A2:2013 |
|
24. |
EN 50117-2-4:2004 Coaxial cables – Part 2-4: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz EN 50117-2-4:2004/A1:2008 EN 50117-2-4:2004/A2:2013 |
|
25. |
EN 50117-2-5:2004 Coaxial cables – Part 2-5: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 3 000 MHz EN 50117-2-5:2004/AC:2012 EN 50117-2-5:2004/A1:2008 EN 50117-2-5:2004/A2:2013 |
|
26. |
EN 50117-3-1:2002 Coaxial cables – Part 3-1: Sectional specifications for cables used in Telecom applications – Miniaturized cables used in digital communication systems |
|
27. |
EN 50117-4-1:2008 Coaxial cables – Part 4-1: Sectional specification for cables for BCT cabling in accordance with EN 50173 – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz EN 50117-4-1:2008/A1:2013 |
|
28. |
EN 50117-4-2:2015 Coaxial cables – Part 4-2: Sectional specification for CATV cables up to 6 GHz used in cabled distribution networks |
|
29. |
EN 50156-1:2015 Electrical equipment for furnaces and ancillary equipment – Part 1: Requirements for application design and installation |
|
30. |
EN 50156-2:2015 Electrical equipment for furnaces and ancillary equipment – Part 2: Requirements for design, development and type approval of safety devices and subsystems |
|
31. |
EN 50214:2006 Flat polyvinyl chloride sheathed flexible cables EN 50214:2006/AC:2007 |
|
32. |
EN 50250:2002 Conversion adaptors for industrial use EN 50250:2002/A1:2015 EN 50250:2002/AC:2007 |
|
33. |
EN 50274:2002 Low-voltage switchgear and controlgear assemblies – Protection against electric shock – Protection against unintentional direct contact with hazardous live parts EN 50274:2002/AC:2009 |
|
34. |
EN 50288-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 1: Generic specification |
|
35. |
EN 50288-2-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 2-1: Sectional specification for screened cables characterised up to 100 MHz – Horizontal and building backbone cables |
|
36. |
EN 50288-2-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 2-2: Sectional specification for screened cables characterised up to 100 MHz – Work area and patch cord cables |
|
37. |
EN 50288-3-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 3-1: Sectional specification for unscreened cables characterised up to 100 MHz – Horizontal and building backbone cables |
|
38. |
EN 50288-3-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz – Work area and patch cord cables |
|
39. |
EN 50288-4-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 4-1: Sectional specification for screened cables characterised up to 600 MHz – Horizontal and building backbone cables |
|
40. |
EN 50288-4-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 4-2: Sectional specification for screened cables characterised up to 600 MHz – Work area and patch cord cables |
|
41. |
EN 50288-5-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 5-1: Sectional specification for screened cables characterized up to 250 MHz – Horizontal and building backbone cables |
|
42. |
EN 50288-5-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 5-2: Sectional specification for screened cables characterized up to 250 MHz – Work area and patch cord cables |
|
43. |
EN 50288-6-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 6-1: Sectional specification for unscreened cables characterised up to 250 MHz – Horizontal and building backbone cables |
|
44. |
EN 50288-6-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz – Work area and patch cord cables |
|
45. |
EN 50288-7:2005 Multi-element metallic cables used in analogue and digital communication and control – Part 7: Sectional specification for instrumentation and control cables |
|
46. |
EN 50288-8:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 8: Specification for type 1 cables characterised up to 2 MHz |
|
47. |
EN 50288-9-1:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 9-1: Sectional specification for screened cables characterised up to 1 000 MHz – Horizontal and building backbone cables |
|
48. |
EN 50288-9-2:2015 Multi-element metallic cables used in analogue and digital communication and control – Part 9-2: Sectional specification for screened cables characterized from 1 MHz up to 1 000 MHz for work area, patch cord and data centre applications |
|
49. |
EN 50288-10-1:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 10-1: Sectional specification for screened cables characterized up to 500 MHz – Horizontal floor and building backbone cables |
|
50. |
EN 50288-10-2:2015 Multi-element metallic cables used in analogue and digital communication and control – Part 10-2: Sectional specification for screened cables characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications |
|
51. |
EN 50288-11-1:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 11-1: Sectional specification for un-screened cables characterised up to 500 MHz – Horizontal and building backbone cables |
|
52. |
EN 50288-11-2:2015 Multi-element metallic cables used in analogue and digital communication and control – Part 11-2: Sectional specification for un-screened cables, characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications |
|
53. |
EN 50289-1-3:2001 Communication cables – Specifications for test methods – Part 1-3: Electrical test methods – Dielectric strength |
|
54. |
EN 50289-1-4:2001 Communication cables – Specifications for test methods – Part 1-4: Electrical test methods – Insulation resistance |
|
55. |
EN 50290-2-1:2005 Communication cables – Part 2-1: Common design rules and construction |
|
56. |
EN 50290-2-20:2001 Communication cables – Part 2-20: Common design rules and construction – General |
|
57. |
EN 50290-2-21:2001 Communication cables – Part 2-21: Common design rules and construction – PVC insulation compounds EN 50290-2-21:2001/A1:2007/AC:2016 EN 50290-2-21:2001/A1:2007 EN 50290-2-21:2001/AC:2003 |
|
58. |
EN 50290-2-22:2001 Communication cables – Part 2-22: Common design rules and construction – PVC sheathing compounds EN 50290-2-22:2001/A1:2007 |
|
59. |
EN 50290-2-23:2013 Communication cables – Part 2-23: Common design rules and construction – Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables |
|
60. |
EN 50290-2-24:2002 Communication cables – Part 2-24: Common design rules and construction – PE sheathing EN 50290-2-24:2002/A1:2008 |
|
61. |
EN 50290-2-25:2013 Communication cables – Part 2-25: Common design rules and construction – Polypropylene insulation compounds |
|
62. |
EN 50290-2-26:2002 Communication cables – Part 2-26: Common design rules and construction – Halogen free flame retardant insulation compounds EN 50290-2-26:2002/A1:2007 |
|
63. |
EN 50290-2-27:2002 Communication cables – Part 2-27: Common design rules and construction – Halogen free flame retardant thermoplastic sheathing compounds EN 50290-2-27:2002/A1:2007 EN 50290-2-27:2002/A1:2007/AC:2010 |
|
64. |
EN 50290-2-28:2002 Communication cables – Part 2-28: Common design rules and construction – Filling compounds for filled cables |
|
65. |
EN 50290-2-29:2002 Communication cables – Part 2-29: Common design rules and construction – Cross-linked PE insulation compounds |
|
66. |
EN 50290-2-30:2002 Communication cables – Part 2-30: Common design rules and construction – Poly(tetrafluoroethylene-hexafluoropropylene) (FEP) insulation and sheathing |
|
67. |
EN 50290-4-1:2014 Communication cables – Part 4-1: General considerations for the use of cables – Environmental conditions and safety aspects |
|
68. |
EN 50290-4-2:2014 Communication cables – Part 4-2: General considerations for the use of cables – Guide to use |
|
69. |
EN 50364:2010 Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications |
|
70. |
EN 50369:2005 Liquid tight sheathing systems for cable management |
|
71. |
EN 50406-1:2004 End user multi-pair cables used in high bit rate telecommunication networks – Part 1: Aerial cables |
|
72. |
EN 50406-2:2004 End user multi-pair cables used in high bit rate telecommunication networks – Part 2: Duct and buried cables |
|
73. |
EN 50407-1:2004 Multi-pair cables used in high bit rate digital access telecommunication networks – Part 1: Outdoor cables |
|
74. |
EN 50407-3:2014 Multi-pair cables used in high bit rate digital access telecommunications networks – Part 3: Indoor multi-pair/quad riser cables up to 100 MHz for maximum length of connection 100 m supporting universal services, xDSL and applications up to 100 Mbit/s over IP |
|
75. |
EN 50428:2005 Switches for household and similar fixed electrical installations – Collateral standard – Switches and related accessories for use in home and building electronic systems (HBES) EN 50428:2005/A1:2007 EN 50428:2005/A2:2009 |
|
76. |
EN 50441-1:2012 Cables for indoor residential telecommunication installations – Part 1: Unscreened cables – Grade 1 |
|
77. |
EN 50441-2:2012 Cables for indoor residential telecommunication installations – Part 2: Screened cables – Grade 1 |
|
78. |
EN 50441-3:2006 Cables for indoor residential telecommunication installations – Part 3: Screened cables – Grade 3 |
|
79. |
EN 50441-4:2012 Cables for indoor residential telecommunication installations – Part 4: Cables up to 1 200 MHz – Grade 3 |
|
80. |
EN 50445:2008 Product family standard to demonstrate compliance of equipment for resistance welding, arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic fields (0 Hz – 300 GHz) |
|
81. |
EN 50491-4-1:2012 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 4-1: General functional safety requirements for products intended to be integrated in Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) |
|
82. |
EN 50491-6-1:2014 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 6-1: HBES installations – Installation and planning |
|
83. |
EN 50520:2020 Cover plates and cover tapes for the protection and location warning of buried cables or buried conduits in underground installations EN 50520:2020/A1:2021 |
|
84. |
EN 50525-1:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 1: General requirements |
|
85. |
EN 50525-2-11:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-11: Cables for general applications – Flexible cables with thermoplastic PVC insulation |
|
86. |
EN 50525-2-12:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-12: Cables for general applications – Cables with thermoplastic PVC insulation for extensible leads |
|
87. |
EN 50525-2-21:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-21: Cables for general applications – Flexible cables with crosslinked elastomeric insulation EN 50525-2-21:2011/AC:2013 |
|
88. |
EN 50525-2-22:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-22: Cables for general applications – High flexibility braided cables with crosslinked elastomeric insulation |
|
89. |
EN 50525-2-31:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-31: Cables for general applications – Single core non-sheathed cables with thermoplastic PVC insulation |
|
90. |
EN 50525-2-41:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-41: Cables for general applications – Single core cables with crosslinked silicone rubber insulation |
|
91. |
EN 50525-2-42:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-42: Cables for general applications – Single core non-sheathed cables with crosslinked EVA insulation |
|
92. |
EN 50525-2-51:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-51: Cables for general applications – Oil resistant control cables with thermoplastic PVC insulation |
|
93. |
EN 50525-2-71:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-71: Cables for general applications – Flat tinsel cables (cords) with thermoplastic PVC insulation |
|
94. |
EN 50525-2-72:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-72: Cables for general applications – Flat divisible cables (cords) with thermoplastic PVC insulation |
|
95. |
EN 50525-2-81:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-81: Cables for general applications – Cables with crosslinked elastomeric covering for arc welding |
|
96. |
EN 50525-2-82:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-82: Cables for general applications – Cables with crosslinked elastomeric insulation for decorative chains |
|
97. |
EN 50525-2-83:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-83: Cables for general applications – Multicore cables with crosslinked silicone rubber insulation |
|
98. |
EN 50525-3-11:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-11: Cables with special fire performance – Flexible cables with halogen-free thermoplastic insulation, and low emission of smoke |
|
99. |
EN 50525-3-21:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-21: Cables with special fire performance – Flexible cables with halogen-free crosslinked insulation, and low emission of smoke EN 50525-3-21:2011/AC:2013 |
|
100. |
EN 50525-3-31:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-31: Cables with special fire performance – Single core non-sheathed cables with halogen-free thermoplastic insulation, and low emission of smoke |
|
101. |
EN 50525-3-41:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-41: Cables with special fire performance – Single core non-sheathed cables with halogen-free crosslinked insulation, and low emission of smoke |
|
102. |
EN 50539-11:2013 Low-voltage surge protective devices – Surge protective devices for specific application including d.c. – Part 11: Requirements and tests for SPDs in photovoltaic applications EN 50539-11:2013/A1:2014 |
|
103. |
EN 50550:2011 Power frequency overvoltage protective device for household and similar applications (POP) EN 50550:2011/AC:2012 EN 50550:2011/A1:2014 |
|
104. |
EN 50556:2011 Road traffic signal systems |
|
105. |
EN 50615:2015 Household and similar electrical appliances – Safety – Particular requirements for devices for fire prevention and suppression for electric hobs (cooktops) |
|
106. |
EN 50618:2014 Electric cables for photovoltaic systems |
|
107. |
EN 50620:2017 Electric cables – Charging cables for electric vehicles EN 50620:2017/A1:2019 |
|
107.I |
EN 50626-1:2023 Conduit systems buried underground for the protection and management of insulated electrical cables or communication cables – Part 1: General requirements |
|
107.II |
EN 50626-2:2023 Conduit systems buried underground for the protection and management of insulated electrical cables or communication cables – Part 2: Polyethylene (PE), Polypropylene (PP) or Unplasticized poly(vinyl chloride) (PVC-U) conduit systems – Requirements for solid wall conduits, fittings and the system used in special applications |
|
108. |
EN 50689:2021 Safety of laser products – Particular Requirements for Consumer Laser Products |
|
109. |
EN 60034-1:2010 Rotating electrical machines – Part 1: Rating and performance EN 60034-1:2010/AC:2010 |
|
110. |
EN 60034-5:2001 Rotating electrical machines – Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification EN 60034-5:2001/A1:2007 |
|
111. |
EN 60034-6:1993 Rotating electrical machines – Part 6: Methods of cooling (IC Code)#IEC 60034-6:1991 |
|
112. |
EN 60034-7:1993 Rotating electrical machines – Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code) EN 60034-7:1993/A1:2001 |
|
113. |
EN 60034-8:2007 Rotating electrical machines – Part 8: Terminal markings and direction of rotation EN 60034-8:2007/A1:2014 |
|
114. |
EN 60034-9:2005 Rotating electrical machines – Part 9: Noise limits EN 60034-9:2005/A1:2007 |
|
115. |
EN 60034-11:2004 Rotating electrical machines – Part 11: Thermal protection |
|
116. |
EN 60034-12:2002 Rotating electrical machines – Part 12: Starting performance of single-speed three-phase cage induction motors EN 60034-12:2002/A1:2007 |
|
117. |
EN 60034-14:2004 Rotating electrical machines – Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher – Measurement, evaluation and limits of vibration severity EN 60034-14:2004/A1:2007 |
|
118. |
EN 60051-1:1998 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 1: Definitions and general requirements common to all parts |
|
119. |
EN 60051-2:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 2: Special requirements for ammeters and voltmeters |
|
120. |
EN 60051-3:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 3: Special requirements for wattmeters and varmeters EN 60051-3:1989/A1:1995 |
|
121. |
EN 60051-4:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 4: Special requirements for frequency meters |
|
122. |
EN 60051-5:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 5: Special requirements for phase meters, power factor meters and synchroscopes |
|
123. |
EN 60051-6:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters |
|
124. |
EN 60051-7:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 7: Special requirements for multi-function instruments |
|
125. |
EN 60051-8:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 8: Special requirements for accessories |
|
126. |
EN 60051-9:1989 Direct acting indicating analogue electrical-measuring instruments and their accessories – Part 9: Recommended test methods EN 60051-9:1989/A1:1995 EN 60051-9:1989/A2:1995 |
|
127. |
EN 60110-1:1998 Power capacitors for induction heating installations – Part 1: General |
|
128. |
EN 60127-1:2006 Miniature fuses – Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links EN 60127-1:2006/A1:2011 EN 60127-1:2006/A2:2015 |
|
129. |
EN 60127-2:2014 Miniature fuses – Part 2: Cartridge fuse-links |
|
130. |
EN 60127-3:1996 Miniature fuses – Part 3: Sub-miniature fuse-links EN 60127-3:1996/A2:2003 EN 60127-3:1996/AC:1996 |
|
131. |
EN 60127-4:2005 Miniature fuses – Part 4: Universal modular fuse-links (UMF) – Through-hole and surface mount types EN 60127-4:2005/A1:2009 EN 60127-4:2005/A2:2013 |
|
132. |
EN 60127-6:2014 Miniature fuses – Part 6: Fuse-holders for miniature fuse-links |
|
133. |
EN 60127-7:2016 Miniature fuses – Part 7: Miniature fuse-links for special applications |
|
134. |
EN 60143-2:2013 Series capacitors for power systems – Part 2: Protective equipment for series capacitor banks |
|
135. |
EN 60155:1995 Glow-starters for fluorescent lamps EN 60155:1995/A1:1995 EN 60155:1995/A2:2007 |
|
136. |
EN 60204-1:2018 Safety of machinery – Electrical equipment of machines – Part 1: General requirements |
|
137. |
EN 60204-32:2008 Safety of machinery – Electrical equipment of machines – Part 32: Requirements for hoisting machines |
|
138. |
EN 60215:1989 Safety requirements for radio transmitting equipment EN 60215:1989/A1:1992 EN 60215:1989/A2:1994 |
|
139. |
EN IEC 60238:2018 Edison screw lampholders |
|
140. |
EN 60252-1:2011 AC motor capacitors – Part 1: General – Performance, testing and rating – Safety requirements – Guidance for installation and operation EN 60252-1:2011/A1:2013 |
|
141. |
EN 60252-2:2011 AC motor capacitors – Part 2: Motor start capacitors EN 60252-2:2011/A1:2013 |
|
142. |
EN 60255-27:2014 Measuring relays and protection equipment – Part 27: Product safety requirements |
|
143. |
EN 60269-1:2007 Low-voltage fuses – Part 1: General requirements EN 60269-1:2007/A1:2009 EN 60269-1:2007/A2:2014 |
|
144. |
HD 60269-2:2013 Low-voltage fuses – Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to K |
|
145. |
HD 60269-3:2010 Low-voltage fuses – Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) – Examples of standardized systems of fuses A to F HD 60269-3:2010/A1:2013 |
|
146. |
EN 60269-4:2009 Low-voltage fuses – Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices EN 60269-4:2009/A1:2012 |
|
147. |
EN 60269-6:2011 Low-voltage fuses – Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems |
|
148. |
EN 60309-1:1999 Plugs, socket-outlets and couplers for industrial purposes – Part 1: General requirements EN 60309-1:1999/A1:2007 EN 60309-1:1999/A2:2012 EN 60309-1:1999/A1:2007/AC:2014 |
|
149. |
EN 60309-2:1999 Plugs, socket-outlets and couplers for industrial purposes – Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories EN 60309-2:1999/A1:2007 EN 60309-2:1999/A2:2012 |
|
150. |
EN 60309-4:2007 Plugs, socket-outlets and couplers for industrial purposes – Part 4: Switched socket-outlets and connectors with or without interlock EN 60309-4:2007/A1:2012 |
|
151. |
EN IEC 60320-1:2021 Appliance couplers for household and similar general purposes – Part 1: General requirements |
|
152. |
EN 60320-2-1:2000 Appliance couplers for household and similar general purposes – Part 2-1: Sewing machine couplers |
|
153. |
EN 60320-2-2:1998 Appliance couplers for household and similar general purposes – Part 2-2: Interconnection couplers for household and similar equipment |
|
154. |
EN IEC 60320-2-4:2021 Appliance couplers for household and similar general purposes – Part 2-4: Couplers dependent on appliance weight for engagement |
|
155. |
EN 60335-1:2012 Household and similar electrical appliances – Safety – Part 1: General requirements EN 60335-1:2012/AC:2014 EN 60335-1:2012/A11:2014 EN 60335-1:2012/A13:2017 EN 60335-1:2012/A1:2019 EN 60335-1:2012/A14:2019 EN 60335-1:2012/A2:2019 EN 60335-1:2012/A15:2021 |
|
156. |
EN 60335-2-2:2010 Household and similar electrical appliances – Safety – Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances EN 60335-2-2:2010/A11:2012 EN 60335-2-2:2010/A1:2013 |
|
157. |
EN 60335-2-3:2016 Household and similar electrical appliances – Safety – Part 2-3: Particular requirements for electric irons EN 60335-2-3:2016/A1:2020 |
|
158. |
EN 60335-2-4:2010 Household and similar electrical appliances – Safety – Part 2-4: Particular requirements for spin extractors EN 60335-2-4:2010/A1:2015 EN 60335-2-4:2010/A11:2018 EN 60335-2-4:2010/A2:2019 |
|
159. |
EN 60335-2-5:2015 Household and similar electrical appliances – Safety – Part 2-5: Particular requirements for dishwashers EN 60335-2-5:2015/A11:2019 EN 60335-2-5:2015/A1:2020 |
|
160. |
EN 60335-2-6:2015 Household and similar electrical appliances – Safety – Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances EN 60335-2-6:2015/A11:2020 |
|
161. |
EN 60335-2-7:2010 Household and similar electrical appliances – Safety – Part 2-7: Particular requirements for washing machines EN 60335-2-7:2010/A11:2013 EN 60335-2-7:2010/A1:2013 EN 60335-2-7:2010/A2:2019 |
|
162. |
EN 60335-2-8:2015 Household and similar electrical appliances – Safety – Part 2-8: Particular requirements for shavers, hair clippers and similar appliances EN 60335-2-8:2015/A1:2016 |
|
163. |
EN 60335-2-9:2003 Household and similar electrical appliances – Safety – Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliances EN 60335-2-9:2003/A1:2004 EN 60335-2-9:2003/A12:2007 EN 60335-2-9:2003/A13:2010 EN 60335-2-9:2003/A2:2006 EN 60335-2-9:2003/A13:2010/AC:2011 EN 60335-2-9:2003/A13:2010/AC:2012 Restriction: The application of the following parts of standard EN 60335-2-9:2003, as last amended by A13:2010, does not confer a presumption of conformity to the safety objectives laid down in point 1(c) of Annex I to Directive 2014/35/EU, in conjunction with point 2(b) of that Annex: – footnote b of Table Z101 in Section 11, – the parts of Section 7.1 which refer to footnote b of Table Z101, – the parts of Section 11.Z10x which refer to ventilation openings. |
|
164. |
EN 60335-2-10:2003 Household and similar electrical appliances – Safety – Part 2-10: Particular requirements for floor treatment machines and wet scrubbing machines EN 60335-2-10:2003/A1:2008 |
|
165. |
EN IEC 60335-2-11:2022 Household and similar electrical appliances – Safety – Part 2-11: Particular requirements for tumble dryers EN IEC 60335-2-11:2022/A11:2022 |
|
166. |
EN 60335-2-12:2003 Household and similar electrical appliances – Safety – Part 2-12: Particular requirements for warming plates and similar appliances EN 60335-2-12:2003/A1:2008 EN 60335-2-12:2003/A11:2019 EN 60335-2-12:2003/A2:2019 |
|
167. |
EN 60335-2-13:2010 Household and similar electrical appliances – Safety – Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances EN 60335-2-13:2010/A11:2012 EN 60335-2-13:2010/A1:2019 |
|
168. |
EN 60335-2-15:2016 Household and similar electrical appliances – Safety – Part 2-15: Particular requirements for appliances for heating liquids EN 60335-2-15:2016/A11:2018 EN 60335-2-15:2016/A1:2021 EN 60335-2-15:2016/A12:2021 EN 60335-2-15:2016/A2:2021 |
|
169. |
EN 60335-2-16:2003 Household and similar electrical appliances – Safety – Part 2-16: Particular requirements for food waste disposers EN 60335-2-16:2003/A1:2008 EN 60335-2-16:2003/A2:2012 EN 60335-2-16:2003/A11:2018 |
|
170. |
EN 60335-2-17:2013 Household and similar electrical appliances – Safety – Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances EN 60335-2-17:2013/A11:2019 EN 60335-2-17:2013/A1:2020 EN 60335-2-17:2013/A2:2021 |
|
171. |
EN 60335-2-21:2021 Household and similar electrical appliances – Safety – Part 2-21: Particular requirements for storage water heaters EN 60335-2-21:2021/A1:2021 |
|
172. |
EN 60335-2-23:2003 Household and similar electrical appliances – Safety – Part 2-23: Particular requirements for appliances for skin or hair care EN 60335-2-23:2003/A11:2010/AC:2012 EN 60335-2-23:2003/A11:2010 EN 60335-2-23:2003/A1:2008 EN 60335-2-23:2003/A2:2015 |
|
173. |
EN IEC 60335-2-24:2022 Household and similar electrical appliances – Safety – Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers EN IEC 60335-2-24:2022/A11:2022 |
|
174. |
EN IEC 60335-2-25:2021 Household and similar electrical appliances – Safety – Part 2-25: Particular requirements for microwave ovens, including combination microwave ovens EN IEC 60335-2-25:2021/A11:2021 |
|
175. |
EN 60335-2-26:2003 Household and similar electrical appliances – Safety – Part 2-26: Particular requirements for clocks EN 60335-2-26:2003/A1:2008 |
|
176. |
EN 60335-2-27:2013 Household and similar electrical appliances – Safety – Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation EN 60335-2-27:2013/A1:2020 EN 60335-2-27:2013/A2:2020 EN 60335-2-27:2013/AC:2021-11 |
|
177. |
EN 60335-2-28:2003 Household and similar electrical appliances – Safety – Part 2-28: Particular requirements for sewing machines EN 60335-2-28:2003/A1:2008 EN 60335-2-28:2003/A11:2018 |
|
178. |
EN 60335-2-29:2021 Household and similar electrical appliances – Safety – Part 2-29: Particular requirements for battery chargers EN 60335-2-29:2021/A1:2021 |
|
179. |
EN 60335-2-30:2009 Household and similar electrical appliances – Safety – Part 2-30: Particular requirements for room heaters EN 60335-2-30:2009/A11:2012 EN 60335-2-30:2009/AC:2010 EN 60335-2-30:2009/AC:2014 EN 60335-2-30:2009/A1:2020 EN 60335-2-30:2009/A12:2020 EN 60335-2-30:2009/A13:2022 EN 60335-2-30:2009/A2:2022 |
|
180. |
EN 60335-2-31:2014 Household and similar electrical appliances – Safety – Part 2-31: Particular requirements for range hoods and other cooking fume extractors |
|
181. |
EN 60335-2-32:2003 Household and similar electrical appliances – Safety – Part 2-32: Particular requirements for massage appliances EN 60335-2-32:2003/A1:2008 EN 60335-2-32:2003/A2:2015 |
|
182. |
EN 60335-2-34:2013 Household and similar electrical appliances – Safety – Part 2-34: Particular requirements for motor-compressors |
|
183. |
EN 60335-2-35:2016 Household and similar electrical appliances – Safety – Part 2-35: Particular requirements for instantaneous water heaters EN 60335-2-35:2016/A1:2019 EN 60335-2-35:2016/A2:2021 |
|
184. |
EN 60335-2-36:2002 Household and similar electrical appliances – Safety – Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements EN 60335-2-36:2002/A1:2004 EN 60335-2-36:2002/A11:2012 EN 60335-2-36:2002/A2:2008 EN 60335-2-36:2002/AC:2007 |
|
185. |
EN 60335-2-37:2002 Household and similar electrical appliances – Safety – Part 2-37: Particular requirements for commercial electric deep fat fryers EN 60335-2-37:2002/A1:2008 EN 60335-2-37:2002/A11:2012 EN 60335-2-37:2002/AC:2007 |
|
186. |
EN 60335-2-38:2003 Household and similar electrical appliances – Safety – Part 2-38: Particular requirements for commercial electric griddles and griddle grills EN 60335-2-38:2003/A1:2008 EN 60335-2-38:2003/AC:2007 |
|
187. |
EN 60335-2-39:2003 Household and similar electrical appliances – Safety – Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans EN 60335-2-39:2003/A1:2004 EN 60335-2-39:2003/A2:2008 EN 60335-2-39:2003/AC:2007 |
|
188. |
EN 60335-2-40:2003 Household and similar electrical appliances – Safety – Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers EN 60335-2-40:2003/A11:2004 EN 60335-2-40:2003/A12:2005 EN 60335-2-40:2003/A1:2006 EN 60335-2-40:2003/A13:2012/AC:2013 EN 60335-2-40:2003/A13:2012 EN 60335-2-40:2003/A2:2009 EN 60335-2-40:2003/AC:2006 EN 60335-2-40:2003/AC:2010 |
|
189. |
EN IEC 60335-2-41:2021 Household and similar electrical appliances – Safety – Particular requirements for pumps EN IEC 60335-2-41:2021/A11:2021 |
|
190. |
EN 60335-2-42:2003 Household and similar electrical appliances – Safety – Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens EN 60335-2-42:2003/A1:2008 EN 60335-2-42:2003/A11:2012 EN 60335-2-42:2003/AC:2007 |
|
191. |
EN IEC 60335-2-43:2020 Household and similar electrical appliances – Safety – Part 2-43: Particular requirements for clothes dryers and towel rails EN IEC 60335-2-43:2020/A11:2020 |
|
192. |
EN 60335-2-44:2002 Household and similar electrical appliances – Safety – Part 2-44: Particular requirements for ironers EN 60335-2-44:2002/A1:2008 EN 60335-2-44:2002/A2:2012 |
|
193. |
EN 60335-2-45:2002 Household and similar electrical appliances – Safety – Part 2-45: Particular requirements for portable heating tools and similar appliances EN 60335-2-45:2002/A1:2008 EN 60335-2-45:2002/A2:2012 |
|
194. |
EN 60335-2-47:2003 Household and similar electrical appliances – Safety – Part 2-47: Particular requirements for commercial electric boiling pans EN 60335-2-47:2003/A1:2008 EN 60335-2-47:2003/A11:2012 EN 60335-2-47:2003/AC:2007 EN 60335-2-47:2003/A2:2019 |
|
195. |
EN 60335-2-48:2003 Household and similar electrical appliances – Safety – Part 2-48: Particular requirements for commercial electric grillers and toasters EN 60335-2-48:2003/A1:2008 EN 60335-2-48:2003/A11:2012 EN 60335-2-48:2003/AC:2007 EN 60335-2-48:2003/A2:2019 |
|
196. |
EN 60335-2-49:2003 Household and similar electrical appliances – Safety – Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm EN 60335-2-49:2003/A1:2008 EN 60335-2-49:2003/A11:2012 EN 60335-2-49:2003/AC:2007 EN 60335-2-49:2003/A2:2019 |
|
197. |
EN 60335-2-50:2003 Household and similar electrical appliances – Safety – Part 2-50: Particular requirements for commercial electric bains-marie EN 60335-2-50:2003/A1:2008 EN 60335-2-50:2003/AC:2007 |
|
198. |
EN 60335-2-51:2003 Household and similar electrical appliances – Safety – Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations EN 60335-2-51:2003/A1:2008 EN 60335-2-51:2003/A2:2012 |
|
199. |
EN 60335-2-52:2003 Household and similar electrical appliances – Safety – Part 2-52: Particular requirements for oral hygiene appliances EN 60335-2-52:2003/A11:2010/AC:2012 EN 60335-2-52:2003/A11:2010 EN 60335-2-52:2003/A1:2008 EN 60335-2-52:2003/A12:2019 |
|
200. |
EN 60335-2-53:2011 Household and similar electrical appliances – Safety – Part 2-53: Particular requirements for sauna heating appliances and infrared cabins |
|
201. |
EN 60335-2-54:2008 Household and similar electrical appliances – Safety – Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam EN 60335-2-54:2008/A11:2012/AC:2015 EN 60335-2-54:2008/A11:2012 EN 60335-2-54:2008/A1:2015 EN 60335-2-54:2008/A12:2021 EN 60335-2-54:2008/A2:2021 |
|
202. |
EN 60335-2-55:2003 Household and similar electrical appliances – Safety – Part 2-55: Particular requirements for electrical appliances for use with aquariums and garden ponds EN 60335-2-55:2003/A1:2008 EN 60335-2-55:2003/A11:2018 |
|
203. |
EN 60335-2-56:2003 Household and similar electrical appliances – Safety – Part 2-56: Particular requirements for projectors and similar appliances EN 60335-2-56:2003/A1:2008 EN 60335-2-56:2003/A2:2014 |
|
204. |
EN 60335-2-58:2005 Household and similar electrical appliances – Safety – Part 2-58: Particular requirements for commercial electric dishwashing machines |
|
205. |
EN 60335-2-59:2003 Household and similar electrical appliances – Safety – Part 2-59: Particular requirements for insect killers EN 60335-2-59:2003/A1:2006 EN 60335-2-59:2003/A2:2009 EN 60335-2-59:2003/A11:2018 |
|
206. |
EN 60335-2-60:2003 Household and similar electrical appliances – Safety – Part 2-60: Particular requirements for whirlpool baths and whirlpool spas EN 60335-2-60:2003/A1:2005 EN 60335-2-60:2003/A12:2010 EN 60335-2-60:2003/A11:2010 EN 60335-2-60:2003/A2:2008 |
|
207. |
EN 60335-2-61:2003 Household and similar electrical appliances – Safety – Part 2-61: Particular requirements for thermal-storage room heaters EN 60335-2-61:2003/A1:2005 EN 60335-2-61:2003/A2:2008 EN 60335-2-61:2003/A11:2019 EN 60335-2-61:2003/A12:2021 |
|
208. |
EN 60335-2-62:2003 Household and similar electrical appliances – Safety – Part 2-62: Particular requirements for commercial electric rinsing sinks EN 60335-2-62:2003/A1:2008 EN 60335-2-62:2003/AC:2007 |
|
209. |
EN 60335-2-65:2003 Household and similar electrical appliances – Safety – Part 2-65: Particular requirements for air-cleaning appliances EN 60335-2-65:2003/A1:2008 EN 60335-2-65:2003/A11:2012 |
|
210. |
EN 60335-2-66:2003 Household and similar electrical appliances – Safety – Part 2-66: Particular requirements for water-bed heaters EN 60335-2-66:2003/A1:2008 EN 60335-2-66:2003/A2:2012 EN 60335-2-66:2003/A11:2019 |
|
211. |
EN 60335-2-70:2002 Household and similar electrical appliances – Safety – Part 2-70: Particular requirements for milking machines |
|
212. |
EN 60335-2-71:2003 Household and similar electrical appliances – Safety – Part 2-71: Particular requirements for electrical heating appliances for breeding and rearing animals EN 60335-2-71:2003/A1:2007 |
|
213. |
EN 60335-2-73:2003 Household and similar electrical appliances – Safety – Part 2-73: Particular requirements for fixed immersion heaters EN 60335-2-73:2003/A1:2006 EN 60335-2-73:2003/A2:2009 EN 60335-2-73:2003/A11:2021 |
|
214. |
EN 60335-2-74:2003 Household and similar electrical appliances – Safety – Part 2-74: Particular requirements for portable immersion heaters EN 60335-2-74:2003/A1:2006 EN 60335-2-74:2003/A2:2009 EN 60335-2-74:2003/A11:2018 |
|
215. |
EN 60335-2-75:2004 Household and similar electrical appliances – Safety – Part 2-75: Particular requirements for commercial dispensing appliances and vending machines EN 60335-2-75:2004/A11:2006 EN 60335-2-75:2004/A1:2005 EN 60335-2-75:2004/A12:2010 EN 60335-2-75:2004/A2:2008 |
|
216. |
EN 60335-2-78:2003 Household and similar electrical appliances – Safety – Part 2-78: Particular requirements for outdoor barbecues EN 60335-2-78:2003/A1:2008 EN 60335-2-78:2003/A11:2020 |
|
217. |
EN 60335-2-80:2003 +6Household and similar electrical appliances – Safety – Part 2-80: Particular requirements for fans EN 60335-2-80:2003/A1:2004 EN 60335-2-80:2003/A2:2009 |
|
218. |
EN 60335-2-81:2003 Household and similar electrical appliances – Safety – Part 2-81: Particular requirements for foot warmers and heating mats EN 60335-2-81:2003/A1:2007 EN 60335-2-81:2003/A2:2012 |
|
219. |
EN 60335-2-82:2003 Household and similar electrical appliances – Safety – Part 2-82: Particular requirements for amusement machines and personal service machines EN 60335-2-82:2003/A1:2008 EN 60335-2-82:2003/A2:2020 |
|
220. |
EN 60335-2-83:2002 Household and similar electrical appliances – Safety – Part 2-83: Particular requirements for heated gullies for roof drainage EN 60335-2-83:2002/A1:2008 |
|
221. |
EN IEC 60335-2-84:2021 Household and similar electrical appliances – Safety – Part 2-84: Particular requirements for toilet appliances EN IEC 60335-2-84:2021/A11:2021 |
|
222. |
EN 60335-2-85:2003 Household and similar electrical appliances – Safety – Part 2-85: Particular requirements for fabric steamers EN 60335-2-85:2003/A1:2008 EN 60335-2-85:2003/A11:2018 EN 60335-2-85:2003/A2:2020 |
|
223. |
EN 60335-2-86:2003 Household and similar electrical appliances – Safety – Part 2-86: Particular requirements for electric fishing machines EN 60335-2-86:2003/A1:2005 EN 60335-2-86:2003/A11:2016 EN 60335-2-86:2003/A2:2016 |
|
224. |
EN 60335-2-87:2002 Household and similar electrical appliances – Safety – Part 2-87: Particular requirements for electrical animal-stunning equipment EN 60335-2-87:2002/A1:2007 EN 60335-2-87:2002/A2:2019 |
|
225. |
EN 60335-2-88:2002 Household and similar electrical appliances – Safety – Part 2-88: Particular requirements for humidifiers intended for use with heating, ventilation, or air-conditioning systems |
|
226. |
EN 60335-2-90:2006 Household and similar electrical appliances – Safety – Part 2-90: Particular requirements for commercial microwave ovens EN 60335-2-90:2006/A1:2010 |
|
227. |
EN IEC 60335-2-96:2021 Household and similar electrical appliances – Safety – Part 2-96: Particular requirements for flexible sheet heating elements for room heating EN IEC 60335-2-96:2021/A11:2021 |
|
228. |
EN 60335-2-97:2006 Household and similar electrical appliances – Safety – Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment EN 60335-2-97:2006/A11:2008 EN 60335-2-97:2006/A12:2015 EN 60335-2-97:2006/A2:2010 |
|
229. |
EN 60335-2-98:2003 Household and similar electrical appliances – Safety – Part 2-98: Particular requirements for humidifiers EN 60335-2-98:2003/A1:2005 EN 60335-2-98:2003/A2:2008 EN 60335-2-98:2003/A11:2019 |
|
230. |
EN 60335-2-99:2003 Household and similar electrical appliances – Safety – Part 2-99: Particular requirements for commercial electric hoods |
|
231. |
EN 60335-2-101:2002 Household and similar electrical appliances – Safety – Part 2-101: Particular requirements for vaporizers EN 60335-2-101:2002/A1:2008 EN 60335-2-101:2002/A2:2014 |
|
232. |
EN 60335-2-102:2016 Household and similar electrical appliances – Safety – Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
|
233. |
EN IEC 60335-2-105:2021 Household and similar electrical appliances – Safety – Part 2-105: Particular requirements for multifunctional shower cabinets EN IEC 60335-2-105:2021/A11:2021 |
|
234. |
EN 60335-2-106:2007 Household and similar electrical appliances – Safety – Part 2-106: Particular requirements for heated carpets and for heating units for room heating installed under removable floor coverings |
|
235. |
EN 60335-2-108:2008 Household and similar electrical appliances – Safety – Part 2-108: Particular requirements for electrolysers |
|
236. |
EN 60335-2-109:2010 Household and similar electrical appliances – Safety – Part 2-109: Particular requirements for UV radiation water treatment appliances EN 60335-2-109:2010/A1:2018 EN 60335-2-109:2010/A2:2018 |
|
237. |
EN 60358-1:2012 Coupling capacitors and capacitor dividers – Part 1: General rules EN 60358-1:2012/AC:2013 |
|
238. |
EN 60360:1998 Standard method of measurement of lamp cap temperature rise |
|
239. |
EN 60399:2004 Barrel thread for lampholders with shade holder ring EN 60399:2004/A1:2008 |
|
240. |
EN 60400:2017 Lampholders for tubular fluorescent lamps and starterholders EN 60400:2017/A1:2021 |
|
241. |
EN 60423:2007 Conduit systems for cable management – Outside diameters of conduits for electrical installations and threads for conduits and fittings |
|
242. |
EN 60432-1:2000 Incandescent lamps – Safety specifications – Part 1: Tungsten filament lamps for domestic and similar general lighting purposes EN 60432-1:2000/A1:2005 EN 60432-1:2000/A2:2012 |
|
243. |
EN 60432-2:2000 Incandescent lamps – Safety specifications – Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes EN 60432-2:2000/A1:2005 EN 60432-2:2000/A2:2012 |
|
244. |
EN 60432-3:2013 Incandescent lamps – Safety specifications – Part 3: Tungsten-halogen lamps (non-vehicle) |
|
245. |
EN 60477:1997 Laboratory d.c. resistors EN 60477:1997/A1:1997 |
|
246. |
EN 60477-2:1997 Laboratory resistors – Part 2: Laboratory a.c. resistors EN 60477-2:1997/A1:1997 |
|
247. |
EN 60519-1:2015 Safety in installations for electroheating and electromagnetic processing – Part 1: General requirements |
|
248. |
EN 60519-2:2006 Safety in electroheat installations – Part 2: Particular requirements for resistance heating equipment |
|
249. |
EN 60519-3:2005 Safety in electroheat installations – Part 3: Particular requirements for induction and conduction heating and induction melting installations |
|
250. |
EN 60519-4:2013 Safety in electroheating installations – Part 4: Particular requirements for arc furnace installations |
|
251. |
EN 60519-6:2011 Safety in electroheat installations – Part 6: Specifications for safety in industrial microwave heating equipment |
|
252. |
EN 60519-7:2008 Safety in electroheat installations – Part 7: Particular requirements for installations with electron guns |
|
253. |
EN 60519-8:2005 Safety in electroheat installations – Part 8: Particular requirements for electroslag remelting furnaces |
|
254. |
EN 60519-9:2005 Safety in electroheat installations – Part 9: Particular requirements for high-frequency dielectric heating installations |
|
255. |
EN 60519-10:2013 Safety in electroheating installations – Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications |
|
256. |
EN 60519-12:2013 Safety in electroheating installations – Part 12: Particular requirements for infrared electroheating installations |
|
257. |
EN 60519-21:2009 Safety in electroheat installations – Part 21: Particular requirements for resistance heating equipment – Heating and melting glass equipment#IEC 60519-21:2008 |
|
258. |
EN 60523:1993 Direct-current potentiometers EN 60523:1993/A2:1997 |
|
259. |
EN 60524:1993 Direct-current resistive volt ratio boxes EN 60524:1993/A2:1997 |
|
260. |
EN 60529:1991 Degrees of protection provided by enclosures (IP Code)#IEC 60529:1989 EN 60529:1991/A1:2000 EN 60529:1991/A2:2013 EN 60529:1991/AC:1993 EN 60529:1991/AC:2016-12 EN 60529:1991/A2:2013/AC:2019-02 |
|
261. |
EN 60564:1993 D.C. bridges for measuring resistance EN 60564:1993/A2:1997 |
|
262. |
EN 60570:2003 Electrical supply track systems for luminaires EN 60570:2003/A1:2018 EN 60570:2003/A2:2020 |
|
263. |
EN IEC 60598-1:2021 Luminaires – Part 1: General requirements and tests EN IEC 60598-1:2021/A11:2022 |
|
264. |
EN 60598-2-1:1989 Luminaires – Part 2: Particular requirements – Section 1: Fixed general purpose luminaires |
|
265. |
EN 60598-2-2:2012 Luminaires – Part 2-2: Particular requirements – Recessed luminaires |
|
266. |
EN 60598-2-3:2003 Luminaires – Part 2-3: Particular requirements – Luminaires for road and street lighting EN 60598-2-3:2003/A1:2011 EN 60598-2-3:2003/AC:2005 |
|
267. |
EN 60598-2-4:2018 Luminaires – Part 2: Particular requirements – Section 4: Portable general purpose luminaires |
|
268. |
EN 60598-2-5:2015 Luminaires – Part 2-5: Particular requirements – Floodlights |
|
269. |
EN 60598-2-8:2013 Luminaires – Part 2-8: Particular requirements – Handlamps |
|
270. |
EN 60598-2-9:1989 Luminaires – Part 2: Particular requirements – Section 9: Photo and film luminaires (non-professional) EN 60598-2-9:1989/A1:1994 |
|
271. |
EN 60598-2-10:2003 Luminaires – Part 2-10: Particular requirements – Portable luminaires for children EN 60598-2-10:2003/AC:2005 |
|
272. |
EN 60598-2-11:2013 Luminaires – Part 2-11: Particular requirements – Aquarium luminaires EN 60598-2-11:2013/A1:2022 |
|
273. |
EN 60598-2-12:2013 Luminaires – Part 2-12: Particular requirements – Mains socket-outlet mounted nightlights |
|
274. |
EN 60598-2-13:2006 Luminaires – Part 2-13: Particular requirements – Ground recessed luminaires EN 60598-2-13:2006/A1:2012 EN 60598-2-13:2006/AC:2006 EN 60598-2-13:2006/A11:2021 |
|
275. |
EN 60598-2-14:2009 Luminaires – Part 2-14: Particular requirements – Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment |
|
276. |
EN IEC 60598-2-17:2018 Luminaires – Part 2-17: Particular requirements – Luminaires for stage lighting, television and film studios (outdoor and indoor) |
|
277. |
EN 60598-2-19:1989 Luminaires – Part 2: Particular requirements – Section 19: Air-handling luminaires (safety requirements) EN 60598-2-19:1989/A2:1998 EN 60598-2-19:1989/AC:2005 |
|
278. |
EN 60598-2-20:2015 Luminaires – Part 2-20: Particular requirements – Lighting chains EN 60598-2-20:2015/AC:2017-01 |
|
279. |
EN 60598-2-21:2015 Luminaires – Part 2-21: Particular requirements – Rope lights EN 60598-2-21:2015/AC:2017-01 |
|
280. |
EN IEC 60598-2-22:2022 Luminaires – Part 2-22: Particular requirements – Luminaires for emergency lighting |
|
281. |
EN IEC 60598-2-23:2021 Luminaires – Part 2-23: Particular requirements – Extra-low-voltage lighting systems for ELV light sources |
|
282. |
EN 60598-2-24:2013 Luminaires – Part 2-24: Particular requirements – Luminaires with limited surface temperatures |
|
283. |
EN 60598-2-25:1994 Luminaires – Part 2-25: Particular requirements – Luminaires for use in clinical areas of hospitals and health care buildings EN 60598-2-25:1994/A1:2004 |
|
284. |
EN 60618:1997 Inductive voltage dividers EN 60618:1997/A2:1997 |
|
285. |
EN 60645-1:2015 Electroacoustics – Audiometric equipment – Part 1: Equipment for pure-tone audiometry |
|
286. |
EN 60645-3:2007 Electroacoustics – Audiometric equipment – Part 3: Test signals of short duration |
|
287. |
EN 60645-6:2010 Electroacoustics – Audiometric equipment – Part 6: Instruments for the measurement of otoacoustic emissions |
|
288. |
EN 60645-7:2010 Electroacoustics – Audiometric equipment – Part 7: Instruments for the measurement of auditory brainstem responses |
|
289. |
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems – Part 1: Principles, requirements and tests |
|
290. |
EN 60664-3:2003 Insulation coordination for equipment within low-voltage systems – Part 3: Use of coating, potting or moulding for protection against pollution EN 60664-3:2003/A1:2010 |
|
291. |
EN 60664-4:2006 Insulation coordination for equipment within low-voltage systems – Part 4: Consideration of high-frequency voltage stress EN 60664-4:2006/AC:2006 |
|
292. |
EN 60669-1:2018 Switches for household and similar fixed electrical installations – Part 1: General requirements EN 60669-1:2018/AC:2018-11 EN 60669-1:2018/AC:2020-02 |
|
293. |
EN 60669-2-1:2004 Switches for household and similar fixed electrical installations – Part 2-1: Particular requirements – Electronic switches EN 60669-2-1:2004/A1:2009 EN 60669-2-1:2004/A12:2010 EN 60669-2-1:2004/AC:2007 |
|
294. |
EN 60669-2-2:2006 Switches for household and similar fixed electrical installations – Part 2-2: Particular requirements – Electromagnetic remote-control switches (RCS) |
|
295. |
EN 60669-2-3:2006 Switches for household and similar fixed electrical installations – Part 2-3: Particular requirements – Time delay switches (TDS) |
|
296. |
EN 60669-2-4:2005 Switches for household and similar fixed electrical installations – Part 2-4: Particular requirements – Isolating switches |
|
297. |
EN 60669-2-6:2012 Switches for household and similar fixed electrical installations – Part 2-6: Particular requirements – Fireman’s switches for exterior and interior signs and luminaires |
|
298. |
EN IEC 60670-1:2021 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 1: General requirements EN IEC 60670-1:2021/A11:2021 |
|
299. |
EN 60670-21:2007 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 21: Particular requirements for boxes and enclosures with provision for suspension means |
|
299a. |
EN 60670-21:2007 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 21: Particular requirements for boxes and enclosures with provision for suspension means EN 60670-21:2007/A11:2023 |
|
300. |
EN 60670-22:2006 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 22: Particular requirements for connecting boxes and enclosures |
|
301. |
EN 60670-23:2008 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 23: Particular requirements for floor boxes and enclosures |
|
301a. |
EN 60670-23:2008 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 23: Particular requirements for floor boxes and enclosures EN 60670-23:2008/A11:2023 |
|
302. |
EN 60670-24:2013 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment |
|
302a. |
EN 60670-24:2013 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment EN 60670-24:2013/A11:2023 |
|
303. |
EN 60688:2013 Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
|
304. |
EN 60691:2016 Thermal-links – Requirements and application guide EN 60691:2016/A1:2019 |
|
305. |
EN 60695-2-10:2013 Fire hazard testing – Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and common test procedure |
|
306. |
EN 60695-2-11:2014 Fire hazard testing – Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014) |
|
307. |
EN 60695-10-2:2014 Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method |
|
308. |
EN 60695-10-3:2002 Fire hazard testing – Part 10-3: Abnormal heat – Mould stress relief distortion test |
|
309. |
EN 60695-11-2:2014 Fire hazard testing – Part 11-2: Test flames – 1 kW nominal pre-mixed flame: Apparatus, confirmatory test arrangement and guidance |
|
310. |
EN 60695-11-3:2012 Fire hazard testing – Part 11-3: Test flames – 500 W flames – Apparatus and confirmational test methods |
|
311. |
EN 60695-11-4:2011 Fire hazard testing – Part 11-4: Test flames – 50 W flame – Apparatus and confirmational test method |
|
312. |
EN 60695-11-5:2005 Fire hazard testing – Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test arrangement and guidance |
|
313. |
EN 60695-11-10:2013 Fire hazard testing – Part 11-10: Test flames – 50 W horizontal and vertical flame test methods EN 60695-11-10:2013/AC:2014 |
|
314. |
EN 60695-11-20:2015 Fire hazard testing – Part 11-20: Test flames – 500 W flame test method EN 60695-11-20:2015/AC:2016 |
|
315. |
EN 60702-1:2002 Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V – Part 1: Cables EN 60702-1:2002/A1:2015 |
|
316. |
EN 60702-2:2002 Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V – Part 2: Terminations EN 60702-2:2002/A1:2015 |
|
317. |
EN 60715:2017 Dimensions of low-voltage switchgear and controlgear – Standardized mounting on rails for mechanical support of switchgear, controlgear and accessories |
|
318. |
EN 60719:1993 Calculation of the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750 V |
|
319. |
EN 60728-11:2017 Cable networks for television signals, sound signals and interactive services – Part 11: Safety EN 60728-11:2017/A11:2018 |
|
320. |
EN 60730-1:2011 Automatic electrical controls for household and similar use – Part 1: General requirements |
|
321. |
EN 60730-2-2:2002 Automatic electrical controls for household and similar use – Part 2-2: Particular requirements for thermal motor protectors EN 60730-2-2:2002/A11:2005 |
|
322. |
EN 60730-2-3:2007 Automatic electrical controls for household and similar use – Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps |
|
323. |
EN 60730-2-4:2007 Automatic electrical controls for household and similar use – Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type |
|
324. |
EN 60730-2-5:2015 Automatic electrical controls – Part 2-5: Particular requirements for automatic electrical burner control systems |
|
325. |
EN 60730-2-6:2016 Automatic electrical controls – Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
|
326. |
EN 60730-2-7:2010 Automatic electrical controls for household and similar use – Part 2-7: Particular requirements for timers and time switches EN 60730-2-7:2010/AC:2011 |
|
327. |
EN 60730-2-8:2002 Automatic electrical controls for household and similar use – Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements EN 60730-2-8:2002/A1:2003 |
|
328. |
EN 60730-2-9:2010 Automatic electrical controls for household and similar use – Part 2-9: Particular requirements for temperature sensing controls |
|
329. |
EN 60730-2-10:2007 Automatic electrical controls for household and similar use – Part 2-10: Particular requirements for motor-starting relays |
|
330. |
EN 60730-2-11:2008 Automatic electrical controls for household and similar use – Part 2-11: Particular requirements for energy regulators |
|
331. |
EN 60730-2-12:2006 Automatic electrical controls for household and similar use – Part 2-12: Particular requirements for electrically operated door locks EN 60730-2-12:2006/A11:2008 |
|
332. |
EN 60730-2-13:2008 Automatic electrical controls for household and similar use – Part 2-13: Particular requirements for humidity sensing controls |
|
333. |
EN 60730-2-14:1997 Automatic electrical controls for household and similar use – Part 2-14: Particular requirements for electric actuators EN 60730-2-14:1997/A11:2005 EN 60730-2-14:1997/A1:2001 EN 60730-2-14:1997/A2:2008 |
|
334. |
EN 60730-2-15:2010 Automatic electrical controls for household and similar use – Part 2-15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls |
|
335. |
EN 60730-2-19:2002 Automatic electrical controls for household and similar use – Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements EN 60730-2-19:2002/A11:2005 EN 60730-2-19:2002/A2:2008 |
|
336. |
EN 60799:1998 Electrical accessories – Cord sets and interconnection cord sets |
|
337. |
EN 60825-1:2014 Safety of laser products – Part 1: Equipment classification and requirements EN 60825-1:2014/A11:2021 |
|
338. |
EN 60825-2:2004 Safety of laser products – Part 2: Safety of optical fibre communication systems (OFCS) EN 60825-2:2004/A1:2007 EN 60825-2:2004/A2:2010 |
|
339. |
EN 60825-4:2006 Safety of laser products – Part 4: Laser guards EN 60825-4:2006/A1:2008 EN 60825-4:2006/A2:2011 |
|
340. |
EN 60825-12:2004 Safety of laser products – Part 12: Safety of free space optical communication systems used for transmission of information |
|
341. |
EN 60831-1:2014 Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V – Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation EN 60831-1:2014/AC:2014 |
|
342. |
EN 60831-2:2014 Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V – Part 2: Ageing test, self-healing test and destruction test |
|
343. |
EN 60838-1:2017 Miscellaneous lampholders – Part 1: General requirements and tests EN 60838-1:2017/A1:2017 EN 60838-1:2017/A11:2021 EN 60838-1:2017/A2:2021 |
|
344. |
EN 60838-2-1:1996 Miscellaneous lampholders – Part 2: Particular requirements – Section 1: Lampholders S14 EN 60838-2-1:1996/A1:1998 EN 60838-2-1:1996/A2:2004 |
|
345. |
EN 60838-2-2:2006 Miscellaneous lampholders – Part 2-2: Particular requirements – Connectors for LED-modules EN 60838-2-2:2006/A1:2012 |
|
346. |
EN 60898-1:2019 Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations – Part 1: Circuit-breakers for a.c. operation |
|
347. |
EN 60898-2:2021 Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations – Part 2: Circuit-breakers for a.c. and d.c. operation |
|
348. |
EN 60931-1:1996 Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation EN 60931-1:1996/A1:2003 |
|
349. |
EN 60931-2:1996 Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 2: Ageing test and destruction test |
|
350. |
EN 60931-3:1996 Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 3: Internal fuses |
|
351. |
EN IEC 60934:2019 Circuit breakers for equipment (CBE) |
|
352. |
EN 60947-1:2007 Low-voltage switchgear and controlgear – Part 1: General rules EN 60947-1:2007/A1:2011 EN 60947-1:2007/A2:2014 |
|
353. |
EN 60947-2:2017 Low-voltage switchgear and controlgear – Part 2: Circuit-breakers EN 60947-2:2017/A1:2020 |
|
354. |
EN IEC 60947-3:2021 Low-voltage switchgear and controlgear – Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units |
|
355. |
EN IEC 60947-4-1:2019 Low-voltage switchgear and controlgear – Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters EN IEC 60947-4-1:2019/AC:2020-05 |
|
356. |
EN 60947-4-2:2012 Low-voltage switchgear and controlgear – Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters |
|
357. |
EN 60947-4-3:2014 Low-voltage switchgear and controlgear – Part 4-3: Contactors and motor-starters – AC semiconductor controllers and contactors for non-motor loads |
|
358. |
EN 60947-5-1:2017 Low-voltage switchgear and controlgear – Part 5-1: Control circuit devices and switching elements – Electromechanical control circuit devices EN 60947-5-1:2017/AC:2020-05 |
|
359. |
EN IEC 60947-5-2:2020 Low-voltage switchgear and controlgear – Part 5-2: Control circuit devices and switching elements – Proximity switches |
|
360. |
EN 60947-5-3:1999 Low-voltage switchgear and controlgear – Part 5-3: Control circuit devices and switching elements – Requirements for proximity devices with defined behaviour under fault conditions (PDF) EN 60947-5-3:1999/A1:2005 |
|
361. |
EN 60947-5-4:2003 Low-voltage switchgear and controlgear – Part 5-4: Control circuit devices and switching elements – Method of assessing the performance of low-energy contacts – Special tests EN 60947-5-4:2003/A1:2019 |
|
362. |
EN 60947-5-5:1997 Low-voltage switchgear and controlgear – Part 5-5: Control circuit devices and switching elements – Electrical emergency stop device with mechanical latching function EN 60947-5-5:1997/A1:2005 EN 60947-5-5:1997/A11:2013 EN 60947-5-5:1997/A2:2017 |
|
363. |
EN 60947-5-7:2003 Low-voltage switchgear and controlgear – Part 5-7: Control circuit devices and switching elements – Requirements for proximity devices with analogue output |
|
364. |
EN IEC 60947-5-8:2021 Low-voltage switchgear and controlgear – Part 5-8: Control circuit devices and switching elements – Three-position enabling switches |
|
365. |
EN 60947-5-9:2007 Low-voltage switchgear and controlgear – Part 5-9: Control circuit devices and switching elements – Flow rate switches |
|
366. |
EN 60947-6-1:2005 Low-voltage switchgear and controlgear – Part 6-1: Multiple function equipment – Transfer switching equipment EN 60947-6-1:2005/A1:2014 |
|
367. |
EN 60947-6-2:2003 Low-voltage switchgear and controlgear – Part 6-2: Multiple function equipment – Control and protective switching devices (or equipment) (CPS) EN 60947-6-2:2003/A1:2007 |
|
368. |
EN 60947-7-1:2009 Low-voltage switchgear and controlgear – Part 7-1: Ancillary equipment – Terminal blocks for copper conductors |
|
369. |
EN 60947-7-2:2009 Low-voltage switchgear and controlgear – Part 7-2: Ancillary equipment – Protective conductor terminal blocks for copper conductors |
|
370. |
EN 60947-7-3:2009 Low-voltage switchgear and controlgear – Part 7-3: Ancillary equipment – Safety requirements for fuse terminal blocks |
|
371. |
EN 60947-8:2003 Low-voltage switchgear and controlgear – Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines EN 60947-8:2003/A1:2006 EN 60947-8:2003/A2:2012 |
|
371a. |
EN IEC 60947-8:2023 Low-voltage switchgear and controlgear – Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines |
|
372. |
EN IEC 60947-9-1:2019 Low-voltage switchgear and controlgear – Part 9-1: Active arc-fault mitigation systems – Arc quenching devices |
|
373. |
EN 60950-21:2003 Information technology equipment – Safety – Part 21: Remote power feeding |
|
374. |
EN 60950-22:2006 Information technology equipment – Safety – Part 22: Equipment installed outdoors EN 60950-22:2006/AC:2008 |
|
375. |
EN 60950-23:2006 Information technology equipment – Safety – Part 23: Large data storage equipment EN 60950-23:2006/AC:2008 |
|
376. |
EN 60968:2015 Self-ballasted fluorescent lamps for general lighting services – Safety requirements |
|
377. |
EN IEC 60974-1:2018 Arc welding equipment – Part 1: Welding power sources EN IEC 60974-1:2018/A1:2019 |
|
378. |
EN IEC 60974-2:2019 Arc welding equipment – Part 2: Liquid cooling systems |
|
379. |
EN IEC 60974-3:2019 Arc welding equipment – Part 3: Arc striking and stabilizing devices |
|
380. |
EN IEC 60974-5:2019 Arc welding equipment – Part 5: Wire feeders |
|
381. |
EN 60974-6:2016 Arc welding equipment – Part 6: Limited duty equipment |
|
382. |
EN IEC 60974-7:2019 Arc welding equipment – Part 7: Torches |
|
383. |
EN IEC 60974-8:2021 Arc welding equipment – Part 8: Gas consoles for welding and plasma cutting systems |
|
384. |
EN IEC 60974-11:2021 Arc welding equipment – Part 11: Electrode holders |
|
385. |
EN 60974-12:2011 Arc welding equipment – Part 12: Coupling devices for welding cables |
|
386. |
EN IEC 60974-13:2021 Arc welding equipment – Part 13: Welding current return clamp |
|
387. |
EN 60998-1:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 1: General requirements |
|
388. |
EN 60998-2-1:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units |
|
389. |
EN 60998-2-2:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units |
|
390. |
EN 60998-2-3:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units |
|
391. |
EN 60998-2-4:2005 Connecting devices for low voltage circuits for household and similar purposes – Part 2-4: Particular requirements for twist-on connecting devices |
|
392. |
EN 60999-1:2000 Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
|
393. |
EN 60999-2:2003 Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included) |
|
394. |
EN 61008-1:2012 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) – Part 1: General rules EN 61008-1:2012/A1:2014 EN 61008-1:2012/A11:2015 EN 61008-1:2012/A2:2014 EN 61008-1:2012/A1:2014/AC:2016-06 EN 61008-1:2012/A12:2017 |
|
395. |
EN 61008-2-1:1994 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) – Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage EN 61008-2-1:1994/A11:1998 EN 61008-2-1:1994/A11:1998/AC:1999 |
|
396. |
EN 61009-1:2012 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) – Part 1: General rules EN 61009-1:2012/A1:2014 EN 61009-1:2012/A11:2015 EN 61009-1:2012/A2:2014 EN 61009-1:2012/A13:2021 |
|
397. |
EN 61009-2-1:1994 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) – Part 2-1: Applicability of the general rules to RCBO’s functionally independent of line voltage EN 61009-2-1:1994/A11:1998 EN 61009-2-1:1994/A11:1998/AC:1999 |
|
398. |
EN 61010-1:2010 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 1: General requirements EN 61010-1:2010/A1:2019/AC:2019-04 EN 61010-1:2010/A1:2019 |
|
399. |
EN IEC 61010-2-010:2020 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-010: Particular requirements for laboratory equipment for the heating of materials |
|
400. |
EN IEC 61010-2-011:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-011: Particular requirements for refrigerating equipment EN IEC 61010-2-011:2021/A11:2021 |
|
401. |
EN IEC 61010-2-012:2022 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-012: Particular requirements for climatic and environmental testing and other temperature conditioning equipment EN IEC 61010-2-012:2022/A11:2022 |
|
402. |
EN 61010-2-020:2006 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-020: Particular requirements for laboratory centrifuges |
|
403. |
EN IEC 61010-2-030:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-030: Particular requirements for equipment having testing or measuring circuits EN IEC 61010-2-030:2021/A11:2021 |
|
404. |
EN IEC 61010-2-032:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement EN IEC 61010-2-032:2021/A11:2021 |
|
405. |
EN IEC 61010-2-033:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-033: Particular requirements for hand-held multimeters for domestic and professional use, capable of measuring mains voltage EN IEC 61010-2-033:2021/A11:2021 |
|
406. |
EN IEC 61010-2-034:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-034: Particular requirements for measurement equipment for insulation resistance and test equipment for electric strength EN IEC 61010-2-034:2021/A11:2021 |
|
407. |
EN IEC 61010-2-040:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials |
|
408. |
EN IEC 61010-2-051:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-051: Particular requirements for laboratory equipment for mixing and stirring EN IEC 61010-2-051:2021/A11:2021 |
|
409. |
EN IEC 61010-2-061:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization EN IEC 61010-2-061:2021/A11:2021 |
|
410. |
EN IEC 61010-2-081:2020 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes |
|
411. |
EN IEC 61010-2-091:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-091: Particular requirements for cabinet X-ray systems EN IEC 61010-2-091:2021/A11:2021 |
|
412. |
EN IEC 61010-2-130:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-130: Particular requirements for equipment intended to be used in educational establishments by children |
|
413. |
EN IEC 61010-2-201:2018 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-201: Particular requirements for control equipment |
|
414. |
EN IEC 61010-2-202:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-202: Particular requirements for electrically operated valve actuators |
|
415. |
EN 61010-031:2015 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test |
|
416. |
EN 61028:1993 Electrical measuring instruments – X-Y recorders EN 61028:1993/A2:1997 |
|
417. |
EN 61048:2006 Auxiliaries for lamps – Capacitors for use in tubular fluorescent and other discharge lamp circuits – General and safety requirements EN 61048:2006/A1:2016 |
|
418. |
EN 61050:1992 Transformers for tubular discharge lamps having a no-load output voltage exceeding 1 kV (generally called neon-transformers) – General and safety requirements EN 61050:1992/A1:1995 |
|
419. |
EN IEC 61058-1:2018 Switches for appliances – Part 1: General requirements |
|
420. |
EN 61058-2-1:2011 Switches for appliances – Part 2-1: Particular requirements for cord switches |
|
421. |
EN 61058-2-4:2005 Switches for appliances – Part 2-4: Particular requirements for independently mounted switches |
|
422. |
EN 61058-2-5:2011 Switches for appliances – Part 2-5: Particular requirements for change-over selectors |
|
423. |
EN 61071:2007 Capacitors for power electronics |
|
424. |
EN 61095:2009 Electromechanical contactors for household and similar purposes |
|
425. |
EN 61131-2:2007 Programmable controllers – Part 2: Equipment requirements and tests |
|
426. |
EN 61138:2007 Cables for portable earthing and short-circuiting equipment |
|
427. |
EN 61140:2002 Protection against electric shock – Common aspects for installation and equipment EN 61140:2002/A1:2006 |
|
428. |
EN 61143-1:1994 Electrical measuring instruments – X-t recorders – Part 1: Definitions and requirements EN 61143-1:1994/A1:1997 |
|
429. |
EN 61143-2:1994 Electrical measuring instruments – X-t recorders – Part 2: Recommended additional test methods |
|
430. |
EN 61184:2017 Bayonet lampholders |
|
431. |
EN 61187:1994 Electrical and electronic measuring equipment – Documentation EN 61187:1994/AC:1995 |
|
432. |
EN 61195:1999 Double-capped fluorescent lamps – Safety specifications EN 61195:1999/A1:2013 EN 61195:1999/A2:2015 |
|
433. |
EN 61199:2011 Single-capped fluorescent lamps – Safety specifications EN 61199:2011/A1:2013 EN 61199:2011/A2:2015 |
|
434. |
EN 61204:1995 Low-voltage power supply devices, d.c. output – Performance characteristics |
|
435. |
EN IEC 61204-7:2018 Low-voltage switch mode power supplies – Part 7: Safety requirements |
|
436. |
EN 61210:2010 Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements |
|
437. |
EN 61230:2008 Live working – Portable equipment for earthing or earthing and short-circuiting |
|
438. |
EN 61242:1997 Electrical accessories – Cable reels for household and similar purposes EN 61242:1997/A1:2008 EN 61242:1997/A2:2016 EN 61242:1997/A1:2008/AC:2010 |
|
439. |
EN 61243-3:2014 Live working – Voltage detectors – Part 3: Two-pole low-voltage type EN 61243-3:2014/AC:2015 EN 61243-3:2014/AC:2015 |
|
440. |
EN 61270-1:1996 Capacitors for microwave ovens – Part 1: General |
|
441. |
EN IEC 61293:2020 Marking of electrical equipment with ratings related to electrical supply – Safety requirements |
|
442. |
EN 61310-1:2008 Safety of machinery – Indication, marking and actuation – Part 1: Requirements for visual, acoustic and tactile signals |
|
443. |
EN 61310-2:2008 Safety of machinery – Indication, marking and actuation – Part 2: Requirements for marking |
|
444. |
EN 61310-3:2008 Safety of machinery – Indication, marking and actuation – Part 3: Requirements for the location and operation of actuators |
|
445. |
EN 61316:1999 Industrial cable reels |
|
446. |
EN 61347-1:2015 Lamp controlgear – Part 1: General and safety requirements |
|
447. |
EN 61347-2-2:2012 Lamp controlgear – Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps |
|
448. |
EN 61347-2-3:2011 Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps EN 61347-2-3:2011/AC:2011 |
|
449. |
EN 61347-2-7:2012 Lamp controlgear – Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) EN 61347-2-7:2012/A1:2019 EN 61347-2-7:2012/A2:2022 |
|
450. |
EN 61347-2-8:2001 Lamp controlgear – Part 2-8: Particular requirements for ballasts for fluorescent lamps EN 61347-2-8:2001/A1:2006 EN 61347-2-8:2001/AC:2003 EN 61347-2-8:2001/AC:2010 |
|
451. |
EN 61347-2-9:2013 Lamp controlgear – Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
|
452. |
EN 61347-2-10:2001 Lamp controlgear – Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) EN 61347-2-10:2001/A1:2009 EN 61347-2-10:2001/AC:2010 |
|
453. |
EN 61347-2-11:2001 Lamp controlgear – Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires EN 61347-2-11:2001/AC:2002 EN 61347-2-11:2001/AC:2010 EN 61347-2-11:2001/A1:2019 |
|
454. |
EN 61347-2-12:2005 Lamp controlgear – Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps) EN 61347-2-12:2005/A1:2010 EN 61347-2-12:2005/AC:2010 |
|
455. |
EN 61347-2-13:2014 Lamp controlgear – Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules |
|
456. |
EN IEC 61347-2-14:2018 Lamp controlgear – Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps EN IEC 61347-2-14:2018/A11:2021 |
|
457. |
EN 61386-1:2008 Conduit systems for cable management – Part 1: General requirements EN 61386-1:2008/A1:2019 |
|
458. |
EN 61386-21:2004 Conduit systems for cable management – Part 21: Particular requirements – Rigid conduit systems EN 61386-21:2004/A11:2010 EN 61386-21:2004/AC:2004 |
|
459. |
EN 61386-22:2004 Conduit systems for cable management – Part 22: Particular requirements – Pliable conduit systems EN 61386-22:2004/A11:2010 EN 61386-22:2004/AC:2004 |
|
460. |
EN 61386-23:2004 Conduit systems for cable management – Part 23: Particular requirements – Flexible conduit systems EN 61386-23:2004/A11:2010 EN 61386-23:2004/AC:2004 |
|
461. |
EN 61386-24:2010 Conduit systems for cable management – Part 24: Particular requirements – Conduit systems buried underground |
|
462. |
EN 61386-25:2011 Conduit systems for cable management – Part 25: Particular requirements – Conduit fixing devices |
|
463. |
EN 61439-1:2011 Low-voltage switchgear and controlgear assemblies – Part 1: General rules |
|
464. |
EN 61439-2:2011 Low-voltage switchgear and controlgear assemblies – Part 2: Power switchgear and controlgear assemblies |
|
465. |
EN 61439-3:2012 Low-voltage switchgear and controlgear assemblies – Part 3: Distribution boards intended to be operated by ordinary persons (DBO) EN 61439-3:2012/AC:2019-04 |
|
466. |
EN 61439-4:2013 Low-voltage switchgear and controlgear assemblies – Part 4: Particular requirements for assemblies for construction sites (ACS) |
|
467. |
EN 61439-5:2015 Low-voltage switchgear and controlgear assemblies – Part 5: Assemblies for power distribution in public networks EN 61439-5:2015/AC:2015 |
|
468. |
EN 61439-6:2012 Low-voltage switchgear and controlgear assemblies – Part 6: Busbar trunking systems (busways) |
|
469. |
EN 61534-1:2011 Powertrack systems – Part 1: General requirements EN 61534-1:2011/A1:2014 EN 61534-1:2011/A11:2021 EN 61534-1:2011/A2:2021 |
|
470. |
EN 61534-21:2014 Powertrack systems – Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting EN 61534-21:2014/A11:2021 |
|
471. |
EN 61534-22:2014 Powertrack systems – Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation EN 61534-22:2014/A11:2021 |
|
472. |
EN IEC 61535:2019 Installation couplers intended for permanent connection in fixed installations |
|
473. |
EN 61537:2007 Cable management – Cable tray systems and cable ladder systems |
|
474. |
EN 61549:2003 Miscellaneous lamps EN 61549:2003/A3:2012 EN 61549:2003/A1:2005 EN 61549:2003/A2:2010 |
|
475. |
EN 61557-1:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 1: General requirements |
|
476. |
EN 61557-2:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 2: Insulation resistance |
|
477. |
EN 61557-3:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 3: Loop impedance |
|
478. |
EN 61557-4:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 4: Resistance of earth connection and equipotential bonding |
|
479. |
EN 61557-5:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 5: Resistance to earth |
|
480. |
EN 61557-6:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems |
|
481. |
EN 61557-7:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 7: Phase sequence |
|
482. |
EN 61557-8:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 8: Insulation monitoring devices for IT systems |
|
483. |
EN 61557-9:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 9: Equipment for insulation fault location in IT systems EN 61557-9:2015/AC:2017-02 |
|
484. |
EN 61557-10:2013 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 10: Combined measuring equipment for testing, measuring or monitoring of protective measures |
|
485. |
EN 61557-11:2009 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems |
|
486. |
EN IEC 61557-12:2022 Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC – Equipment for testing, measuring or monitoring of protective measures – Part 12: Power metering and monitoring devices (PMD) |
|
487. |
EN 61557-13:2011 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems |
|
488. |
EN 61557-14:2013 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 14: Equipment for testing the safety of electrical equipment of machinery |
|
489. |
EN 61557-15:2014 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 15: Functional safety requirements for insulation monitoring devices in IT systems and equipment for insulation fault location in IT systems |
|
490. |
EN 61557-16:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 16: Equipment for testing the effectiveness of the protective measures of electrical equipment and/or medical electrical equipment |
|
491. |
EN IEC 61558-1:2019 Safety of transformers, reactors, power supply units and combinations thereof – Part 1: General requirements and tests |
|
492. |
EN 61558-2-1:2007 Safety of power transformers, power supplies, reactors and similar products – Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications |
|
493. |
EN 61558-2-2:2007 Safety of power transformers, power supplies, reactors and similar products – Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers |
|
494. |
EN 61558-2-3:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners |
|
495. |
EN 61558-2-4:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers |
|
496. |
EN 61558-2-5:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-5: Particular requirements and tests for transformer for shavers, power supply units for shavers and shaver supply units |
|
497. |
EN 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
|
498. |
EN 61558-2-7:2007 Safety of power transformers, power supplies, reactors and similar products – Part 2-7: Particular requirements and tests for transformers and power supplies for toys |
|
499. |
EN 61558-2-8:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes |
|
500. |
EN 61558-2-9:2011 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps |
|
501. |
EN 61558-2-12:2011 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage |
|
502. |
EN 61558-2-13:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers |
|
503. |
EN 61558-2-14:2013 Safety of transformers, reactors, power supply units and combination thereof – Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers |
|
504. |
EN 61558-2-15:2012 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations |
|
505. |
EN 61558-2-16:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units EN 61558-2-16:2009/A1:2013 |
|
506. |
EN 61558-2-20:2011 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-20: Particular requirements and tests for small reactors |
|
507. |
EN 61558-2-23:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites |
|
508. |
EN 61558-2-26:2013 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-26: Particular requirements and tests for transformers and power supply units for saving energy and other purposes |
|
509. |
EN 61643-11:2012 Low-voltage surge protective devices – Part 11: Surge protective devices connected to low-voltage power systems – Requirements and test methods EN 61643-11:2012/A11:2018 |
|
510. |
EN 61643-21:2001 Low voltage surge protective devices – Part 21: Surge protective devices connected to telecommunications and signalling networks – Performance requirements and testing methods EN 61643-21:2001/A1:2009 EN 61643-21:2001/A2:2013 |
|
511. |
EN 61643-31:2019 Low-voltage surge protective devices – Part 31: Requirements and test methods for SPDs for photovoltaic installations |
|
512. |
EN IEC 61730-1:2018 Photovoltaic (PV) module safety qualification – Part 1: Requirements for construction EN IEC 61730-1:2018/AC:2018-06 |
|
513. |
EN IEC 61730-2:2018 Photovoltaic (PV) module safety qualification – Part 2: Requirements for testing EN IEC 61730-2:2018/AC:2018-06 |
|
514. |
EN 61770:2009 Electric appliances connected to the water mains – Avoidance of backsiphonage and failure of hose-sets EN 61770:2009/AC:2011 |
|
515. |
EN 61800-5-1:2007 Adjustable speed electrical power drive systems – Part 5-1: Safety requirements – Electrical, thermal and energy EN 61800-5-1:2007/A1:2017 EN 61800-5-1:2007/A11:2021 |
|
516. |
EN 61812-1:2011 Time relays for industrial and residential use – Part 1: Requirements and tests |
|
517. |
EN IEC 61851-1:2019 Electric vehicle conductive charging system – Part 1: General requirements |
|
518. |
EN 61851-21:2002 Electric vehicle conductive charging system – Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply |
|
519. |
EN 61851-23:2014 Electric vehicle conductive charging system – Part 23: DC electric vehicle charging station EN 61851-23:2014/AC:2016-06 |
|
520. |
EN 61851-24:2014 Electric vehicle conductive charging system – Part 24: Digital communication between a d.c. EV charging station and an electric vehicle for control of d.c. charging EN 61851-24:2014/AC:2015 |
|
521. |
EN 61869-1:2009 Instrument transformers – Part 1: General requirements |
|
522. |
EN 61869-2:2012 Instrument transformers – Part 2: Additional requirements for current transformers |
|
523. |
EN 61869-3:2011 Instrument transformers – Part 3: Additional requirements for inductive voltage transformers |
|
524. |
EN 61869-4:2014 Instrument transformers – Part 4: Additional requirements for combined transformers EN 61869-4:2014/AC:2014 |
|
525. |
EN 61869-5:2011 Instrument transformers – Part 5: Additional requirements for capacitor voltage transformers EN 61869-5:2011/AC:2015 |
|
526. |
EN IEC 61914:2021 Cable cleats for electrical installations |
|
527. |
EN 61921:2003 Power capacitors – Low-voltage power factor correction banks |
|
528. |
EN 61995-1:2008 Devices for the connection of luminaires for household and similar purposes – Part 1: General requirements EN 61995-1:2008/A1:2017 EN 61995-1:2008/A11:2021 |
|
529. |
EN 61995-2:2009 Devices for the connection of luminaires for household and similar purposes – Part 2: Standard sheets for DCL |
|
530. |
EN 62020:1998 Electrical accessories – Residual current monitors for household and similar uses (RCMs) EN 62020:1998/A1:2005 |
|
531. |
EN 62026-1:2007 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 1: General rules |
|
532. |
EN 62026-2:2013 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 2: Actuator sensor interface (AS-i) |
|
533. |
EN 62026-3:2015 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 3: DeviceNet EN 62026-3:2015/AC:2019-12 |
|
534. |
EN 62026-7:2013 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 7: CompoNet |
|
535. |
EN IEC 62031:2020 LED modules for general lighting – Safety specifications EN IEC 62031:2020/A11:2021 |
|
536. |
EN 62035:2014 Discharge lamps (excluding fluorescent lamps) – Safety specifications EN 62035:2014/A1:2019 |
|
537. |
EN IEC 62040-1:2019 Uninterruptible power systems (UPS) – Part 1: Safety requirements EN IEC 62040-1:2019/A11:2021 |
|
538. |
EN 62080:2009 Sound signalling devices for household and similar purposes |
|
539. |
EN 62094-1:2003 Indicator light units for household and similar fixed-electrical installations – Part 1: General requirements EN 62094-1:2003/A11:2003 |
|
540. |
EN 62109-1:2010 Safety of power converters for use in photovoltaic power systems – Part 1: General requirements |
|
541. |
EN 62109-2:2011 Safety of power converters for use in photovoltaic power systems – Part 2: Particular requirements for inverters |
|
542. |
EN 62135-1:2015 Resistance welding equipment – Part 1: Safety requirements for design, manufacture and installation EN 62135-1:2015/AC:2016-02 |
|
543. |
EN 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 1: General requirements |
|
544. |
EN 62196-2:2012 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories EN 62196-2:2012/A12:2014/AC:2014 EN 62196-2:2012/A12:2014 EN 62196-2:2012/A11:2013 |
|
545. |
EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers |
|
546. |
EN 62208:2011 Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements |
|
547. |
EN 62233:2008 Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure EN 62233:2008/AC:2008 |
|
548. |
EN 62253:2011 Photovoltaic pumping systems – Design qualification and performance measurements |
|
549. |
EN IEC 62275:2019 Cable management systems – Cable ties for electrical installations |
|
550. |
EN 62282-3-100:2012 Fuel cell technologies – Part 3-100: Stationary fuel cell power systems – Safety |
|
551. |
EN 62282-3-300:2012 Fuel cell technologies – Part 3-300: Stationary fuel cell power systems – Installation |
|
552. |
EN 62282-5-1:2012 Fuel cell technologies – Part 5-1: Portable fuel cell power systems – Safety |
|
553. |
EN 62310-1:2005 Static transfer systems (STS) – Part 1: General and safety requirements |
|
554. |
EN 62311:2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300 GHz) |
|
555. |
EN 62368-1:2014 Audio/video, information and communication technology equipment – Part 1: Safety requirements (IEC 62368-1:2014, modified) EN 62368-1:2014/AC:2015 |
|
556. |
EN 62395-1:2013 Electrical resistance trace heating systems for industrial and commercial applications – Part 1: General and testing requirements |
|
557. |
EN 62423:2012 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses EN 62423:2012/A11:2021 EN 62423:2012/A12:2022 |
|
558. |
EN 62444:2013 Cable glands for electrical installations |
|
559. |
EN 62471:2008 Photobiological safety of lamps and lamp systems |
|
560. |
EN 62477-1:2012 Safety requirements for power electronic converter systems and equipment – Part 1: General EN 62477-1:2012/A11:2014 EN 62477-1:2012/A1:2017 EN 62477-1:2012/A12:2021 |
|
561. |
EN 62479:2010 Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz) |
|
562. |
EN 62493:2010 Assessment of lighting equipment related to human exposure to electromagnetic fields |
|
563. |
EN 62532:2011 Fluorescent induction lamps – Safety specifications |
|
564. |
EN 62549:2011 Articulated systems and flexible systems for cable guiding |
|
565. |
EN 62560:2012 Self-ballasted LED-lamps for general lighting services by voltage > 50 V – Safety specifications EN 62560:2012/A1:2015 EN 62560:2012/A1:2015/AC:2015 EN 62560:2012/AC:2015 EN 62560:2012/A11:2019 |
|
566. |
EN 62606:2013 General requirements for arc fault detection devices EN 62606:2013/A1:2017 |
|
567. |
EN 62626-1:2014 Low-voltage switchgear and controlgear enclosed equipment – Part 1: Enclosed switch-disconnectors outside the scope of IEC 60947-3 to provide isolation during repair and maintenance work |
|
568. |
HD 62640:2015 Residual current devices with or without overcurrent protection for socket-outlets for household and similar uses |
|
569. |
EN 62776:2015 Double-capped LED lamps designed to retrofit linear fluorescent lamps – Safety specifications |
|
570. |
EN 62868:2015 Organic light emitting diode (OLED) panels for general lighting – Safety requirements |
|
571. |
EN 62949:2017 Particular safety requirements for equipment to be connected to information and communication networks |
|
572. |
EN 63024:2018 Requirements for automatic reclosing devices (ARDs) for circuit-breakers, RCBOs and RCCBs for household and similar uses |
|
573. |
EN IEC 63044-3:2018 Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 3: Electrical safety requirements |
ANNEX II
|
|
Reference of the standard |
Date of withdrawal |
|
1. |
EN 60335-2-24:2010 Household and similar electrical appliances – Safety – Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers EN 60335-2-24:2010/A1:2019 EN 60335-2-24:2010/A11:2020 EN 60335-2-24:2010/A2:2019 Restriction: For the purposes of presumption of conformity with the corresponding safety objectives, referred to in Article 3 of Directive 2014/35/EU and set out in Annex I to that Directive: (a) the text ‘an area exceeding 75 cm2’, in its clause 30.2, shall be read as ‘a total area exceeding 75 cm2 (75 cm2 shall be considered the sum of all holes in back part of an appliance)’; (b) the text ‘an area not exceeding 75 cm2’, in its clause 30.2.101, shall be read as ‘a total area not exceeding 75 cm2 (75 cm2 shall be considered the sum of all holes in back part of an appliance).’ |
13.6.2025 |
|
2. |
EN 60335-2-30:2009 Household and similar electrical appliances – Safety – Part 2-30: Particular requirements for room heaters EN 60335-2-30:2009/A11:2012 EN 60335-2-30:2009/AC:2010 EN 60335-2-30:2009/AC:2014 EN 60335-2-30:2009/A1:2020 EN 60335-2-30:2009/A12:2020 |
17.9.2024 |
|
3. |
EN 60598-2-22:2014 Luminaires – Part 2-22: Particular requirements – Luminaires for emergency lighting EN 60598-2-22:2014/AC:2015 EN 60598-2-22:2014/AC:2016-05 EN 60598-2-22:2014/AC:2016-09 EN 60598-2-22:2014/A1:2020 |
11.7.2024 |
|
11. |
EN 61347-2-7:2012 Lamp controlgear – Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) EN 61347-2-7:2012/A1:2019 |
11.7.2024 |
|
12. |
EN 62423:2012 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses EN 62423:2012/A11:2021 |
17.9.2024 |
ANNEX III
|
No |
Reference of the standard |
Date of withdrawal |
|
1. |
HD 361 S3:1999 System for cable designation HD 361 S3:1999/A1:2006, HD 361 S3:1999/AC:1999 |
13.6.2025 |
|
2. |
HD 605 S2:2008 Electric cables – Additional test methods HD 605 S2:2008/AC:2010 |
13.6.2025 |
|
3. |
EN 50363-0:2011 Insulating, sheathing and covering materials for low-voltage energy cables – Part 0: General introduction |
13.6.2025 |
|
4. |
EN 50363-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 1: Cross-linked elastomeric insulating compounds |
13.6.2025 |
|
5. |
EN 50363-2-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 2-1: Cross-linked elastomeric sheathing compounds EN 50363-2-1:2005/A1:2011 |
13.6.2025 |
|
6. |
EN 50363-2-2:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 2-2: Cross-linked elastomeric covering compounds |
13.6.2025 |
|
7. |
EN 50363-3:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 3: PVC insulating compounds EN 50363-3:2005/A1:2011 |
13.6.2025 |
|
8. |
EN 50363-4-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 4-1: PVC sheathing compounds |
13.6.2025 |
|
9. |
EN 50363-4-2:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 4-2: PVC covering compounds |
13.6.2025 |
|
10. |
EN 50363-5:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 5: Halogen-free, cross-linked insulating compounds EN 50363-5:2005/A1:2011 |
13.6.2025 |
|
11. |
EN 50363-6:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 6: Halogen-free, cross-linked sheathing compounds EN 50363-6:2005/A1:2011 |
13.6.2025 |
|
12. |
EN 50363-7:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 7: Halogen-free, thermoplastic insulating compounds |
13.6.2025 |
|
13. |
EN 50363-8:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 8: Halogen-free, thermoplastic sheathing compounds EN 50363-8:2005/A1:2011 |
13.6.2025 |
|
14. |
EN 50363-9-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 9-1: Miscellaneous insulating compounds – Cross-linked polyvinyl chloride (XLPVC) |
13.6.2025 |
|
15. |
EN 50363-10-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 10-1: Miscellaneous sheathing compounds – Cross-linked polyvinyl chloride (XLPVC) |
13.6.2025 |
|
16. |
EN 50363-10-2:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 10-2: Miscellaneous sheathing compounds – Thermoplastic polyurethane |
13.6.2025 |
|
17. |
EN 50395:2005 Electrical test methods for low voltage energy cables EN 50395:2005/A1:2011 |
13.6.2025 |
|
18. |
EN 50396:2005 Non electrical test methods for low voltage energy cables EN 50396:2005/A1:2011 |
13.6.2025 |
|
19. |
EN 50497:2007 Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables |
13.6.2025 |
|
20. |
EN 50565-1:2014 Electric cables – Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) – Part 1: General guidance |
13.6.2025 |
|
21. |
EN 50565-2:2014 Electric cables – Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) – Part 2: Specific guidance related to EN 50525 cable types |
13.6.2025 |
|
22. |
EN 60228:2005 Conductors of insulated cables EN 60228:2005/AC:2005 |
13.6.2025 |
|
23. |
EN 60332-1-1:2004 Tests on electric and optical fibre cables under fire conditions – Part 1-1: Test for vertical flame propagation for a single insulated wire or cable – Apparatus EN 60332-1-1:2004/A1:2015 |
13.6.2025 |
|
24. |
EN 60332-1-2:2004 Tests on electric and optical fibre cables under fire conditions – Part 1-2: Test for vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixed flame EN 60332-1-2:2004/A1:2015 |
13.6.2025 |
|
25. |
EN 60332-1-3:2004 Tests on electric and optical fibre cables under fire conditions – Part 1-3: Test for vertical flame propagation for a single insulated wire or cable – Procedure for determination of flaming droplets/particles EN 60332-1-3:2004/A1:2015 |
13.6.2025 |
|
26. |
EN 60332-2-1:2004 Tests on electric and optical fibre cables under fire conditions – Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus |
13.6.2025 |
|
27. |
EN 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions – Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame |
13.6.2025 |
|
28. |
EN 60332-3-10:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables – Apparatus |
13.6.2025 |
|
29. |
EN 60332-3-21:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A F/R |
13.6.2025 |
|
30. |
EN 60332-3-22:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A |
13.6.2025 |
|
31. |
EN 60332-3-23:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B |
13.6.2025 |
|
32. |
EN 60332-3-24:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category C |
13.6.2025 |
|
33. |
EN 60332-3-25:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category D |
13.6.2025 |
|
34. |
EN 60335-2-11:2010 Household and similar electrical appliances – Safety – Part 2-11: Particular requirements for tumble dryers EN 60335-2-11:2010/A11:2012 EN 60335-2-11:2010/A1:2015 |
17.9.2024 |
|
35. |
EN 60598-1:2015 Luminaires – Part 1: General requirements and tests EN 60598-1:2015/AC:2015 EN 60598-1:2015/AC:2016 EN 60598-1:2015/AC:2017-05 EN 60598-1:2015/A1:2018 |
11.7.2024 |
|
36. |
EN 60598-2-11:2013 Luminaires – Part 2-11: Particular requirements – Aquarium luminaires |
17.9.2024 |
|
37. |
EN 60754-1:2014 Test on gases evolved during combustion of materials from cables – Part 1: Determination of the halogen acid gas content |
13.6.2025 |
|
38. |
EN 60754-2:2014 Test on gases evolved during combustion of materials from cables – Part 2: Determination of acidity (by pH measurement) and conductivity |
13.6.2025 |
|
39. |
EN 60811-100:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 100: General |
13.6.2025 |
|
40. |
EN 60811-201:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 201: General tests – Measurement of insulation thickness |
13.6.2025 |
|
41. |
EN 60811-202:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 202: General tests – Measurement of thickness of non-metallic sheath |
13.6.2025 |
|
42. |
EN 60811-203:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 203: General tests – Measurement of overall dimensions |
13.6.2025 |
|
43. |
EN 60811-301:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 301: Electrical tests – Measurement of the permittivity at 23 °C of filling compounds |
13.6.2025 |
|
44. |
EN 60811-302:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 302: Electrical tests – Measurement of the d.c. resistivity at 23 °C and 100 °C of filling compounds |
13.6.2025 |
|
45. |
EN 60811-401:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven |
13.6.2025 |
|
46. |
EN 60811-402:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 402: Miscellaneous tests – Water absorption tests |
13.6.2025 |
|
47. |
EN 60811-403:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 403: Miscellaneous tests – Ozone resistance test on cross-linked compounds |
13.6.2025 |
|
48. |
EN 60811-404:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths |
13.6.2025 |
|
49. |
EN 60811-405:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 405: Miscellaneous tests – Thermal stability test for PVC insulations and PVC sheaths |
13.6.2025 |
|
50. |
EN 60811-406:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 406: Miscellaneous tests – Resistance to stress cracking of polyethylene and polypropylene compounds |
13.6.2025 |
|
51. |
EN 60811-407:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 407: Miscellaneous tests – Measurement of mass increase of polyethylene and polypropylene compounds |
13.6.2025 |
|
52. |
EN 60811-408:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 408: Miscellaneous tests – Long-term stability test of polyethylene and polypropylene compounds |
13.6.2025 |
|
53. |
EN 60811-409:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 409: Miscellaneous tests – Loss of mass test for thermoplastic insulations and sheaths |
13.6.2025 |
|
54. |
EN 60811-410:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 410: Miscellaneous tests – Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors |
13.6.2025 |
|
55. |
EN 60811-411:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 411: Miscellaneous tests – Low-temperature brittleness of filling compounds |
13.6.2025 |
|
56. |
EN 60811-412:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 412: Miscellaneous tests – Thermal ageing methods – Ageing in an air bomb |
13.6.2025 |
|
57. |
EN 60811-501:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 501: Mechanical tests – Tests for determining the mechanical properties of insulating and sheathing compounds |
13.6.2025 |
|
58. |
EN 60811-502:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 502: Mechanical tests – Shrinkage test for insulations |
13.6.2025 |
|
59. |
EN 60811-503:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 503: Mechanical tests – Shrinkage test for sheaths |
13.6.2025 |
|
60. |
EN 60811-504:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 504: Mechanical tests – Bending tests at low temperature for insulation and sheaths |
13.6.2025 |
|
61. |
EN 60811-505:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 505: Mechanical tests – Elongation at low temperature for insulations and sheaths |
13.6.2025 |
|
62. |
EN 60811-506:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 506: Mechanical tests – Impact test at low temperature for insulations and sheaths |
13.6.2025 |
|
63. |
EN 60811-507:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 507: Mechanical tests – Hot set test for cross-linked materials |
13.6.2025 |
|
64. |
EN 60811-508:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 508: Mechanical tests – Pressure test at high temperature for insulation and sheaths |
13.6.2025 |
|
65. |
EN 60811-509:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 509: Mechanical tests – Test for resistance of insulations and sheaths to cracking (heat shock test) |
13.6.2025 |
|
66. |
EN 60811-510:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 510: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after thermal ageing in air |
13.6.2025 |
|
67. |
EN 60811-511:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 511: Mechanical tests – Measurement of the melt flow index of polyethylene compounds |
13.6.2025 |
|
68. |
EN 60811-512:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 512: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature |
13.6.2025 |
|
69. |
EN 60811-513:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 513: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after conditioning |
13.6.2025 |
|
70. |
EN 60811-601:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 601: Physical tests – Measurement of the drop point of filling compounds |
13.6.2025 |
|
71. |
EN 60811-602:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 602: Physical tests – Separation of oil in filling compounds |
13.6.2025 |
|
72. |
EN 60811-603:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 603: Physical tests – Measurement of total acid number of filling compounds |
13.6.2025 |
|
73. |
EN 60811-604:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 604: Physical tests – Measurement of absence of corrosive components in filling compounds |
13.6.2025 |
|
74. |
EN 60811-605:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 605: Physical tests – Measurement of carbon black and/or mineral filler in polyethylene compounds |
13.6.2025 |
|
75. |
EN 60811-606:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 606: Physical tests – Methods for determining the density#IEC 60811-606:2012 |
13.6.2025 |
|
76. |
EN 60811-607:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 607: Physical tests – Test for the assessment of carbon black dispersion in polyethylene and polypropylene |
13.6.2025 |
|
77. |
EN 61034-1:2005 Measurement of smoke density of cables burning under defined conditions – Part 1: Test apparatus EN 61034-1:2005/A1:2014 |
13.6.2025 |
|
78. |
EN 61034-2:2005 Measurement of smoke density of cables burning under defined conditions – Part 2: Test procedure and requirements EN 61034-2:2005/A1:2013 |
13.6.2025 |
|
79. |
EN 61557-12:2008 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 12: Performance measuring and monitoring devices (PMD) |
11.7.2024 |