This document is an excerpt from the EUR-Lex website
Document 02003L0097-20050419
Directive 2003/97/EC of the European Parliament and of the Council of 10 November 2003 on the approximation of the laws of the Member States relating to the type-approval of devices for indirect vision and of vehicles equipped with these devices, amending Directive 70/156/EEC and repealing Directive 71/127/EEC (Text with EEA relevance)
Consolidated text: Directive 2003/97/EC of the European Parliament and of the Council of 10 November 2003 on the approximation of the laws of the Member States relating to the type-approval of devices for indirect vision and of vehicles equipped with these devices, amending Directive 70/156/EEC and repealing Directive 71/127/EEC (Text with EEA relevance)
Directive 2003/97/EC of the European Parliament and of the Council of 10 November 2003 on the approximation of the laws of the Member States relating to the type-approval of devices for indirect vision and of vehicles equipped with these devices, amending Directive 70/156/EEC and repealing Directive 71/127/EEC (Text with EEA relevance)
2003L0097 — EN — 19.04.2005 — 001.001
This document is meant purely as a documentation tool and the institutions do not assume any liability for its contents
DIRECTIVE 2003/97/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 10 November 2003 on the approximation of the laws of the Member States relating to the type-approval of devices for indirect vision and of vehicles equipped with these devices, amending Directive 70/156/EEC and repealing Directive 71/127/EEC (OJ L 025, 29.1.2004, p.1) |
Amended by:
|
|
Official Journal |
||
No |
page |
date |
||
Commission Directive 2005/27/EC Text with EEA relevance of 29 March 2005 |
L 81 |
44 |
30.3.2005 |
DIRECTIVE 2003/97/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL
of 10 November 2003
on the approximation of the laws of the Member States relating to the type-approval of devices for indirect vision and of vehicles equipped with these devices, amending Directive 70/156/EEC and repealing Directive 71/127/EEC
(Text with EEA relevance)
THE EUROPEAN PARLIAMENT AND THE COUNCIL OF THE EUROPEAN UNION,
Having regard to the Treaty establishing the European Community, and in particular Article 95 thereof,
Having regard to the proposal from the Commission ( 1 ),
Having regard to the opinion of the European Economic and Social Committee ( 2 ),
Acting in accordance with the procedure laid down in Article 251 of the Treaty ( 3 ),
Whereas:
(1) |
Council Directive 71/127/EEC of 1 March 1971 on the approximation of the laws of the Member States relating to the rear-view mirrors of motor vehicles ( 4 ) was adopted as one of the separate directives of the EC type-approval procedure which was established by Council Directive 70/156/EEC of 6 February 1970 on the approximation of the laws of the Member States relating to the type-approval of motor vehicles and their trailers ( 5 ). Consequently, the provisions laid down in Directive 70/156/EEC relating to vehicle systems, components and separate technical units apply to Directive 71/127/EEC. |
(2) |
Existing provisions, in particular in the case of categories N2, N3, M2 and M3 have proved inadequate as regards the exterior field of vision to the side, front and rear of the vehicle. In order to remedy this shortcoming, it is necessary to require an extension of the field of vision. |
(3) |
In the light of the experience gained and the present state of the art, it is now possible to amplify certain requirements of Directive 71/127/EEC with a view to improving road safety and to permit the use of mirrors to be supplemented by other technologies. |
(4) |
Taking into account the nature and the number of changes necessary to the requirements in force today, it is advisable to repeal andreplace Directive 71/127/EEC by this Directive. Since the type-approval and the conformity of production procedures are provided for in Directive 70/156/EEC, it is not necessary to repeat them in this Directive. |
(5) |
The Annexes to Directive 70/156/EEC should be amended accordingly, |
HAVE ADOPTED THIS DIRECTIVE:
Article 1
The aim of this Directive is to harmonise rules relating to the type-approval of devices for indirect vision and of vehicles equipped with these devices.
These rules are contained in the Annexes to this Directive.
For the purpose of this Directive ‘vehicle’ means any motor vehicle as defined in Section A of Annex II to Directive 70/156/EEC.
Article 2
1. With effect from 26 January 2005, Member States shall not, on grounds relating to devices for indirect vision,
— refuse to grant EC type-approval or national type-approval of a vehicle or a device for indirect vision,
— prohibit the sale, registration or entry into service of vehicles or devices for indirect vision,
1. if the vehicles or devices for indirect vision comply with the requirements of this Directive.
2. With effect from 26 January 2006, Member States shall refuse to grant EC type-approval for any new type of vehicle on grounds relating to the device for indirect vision or for any new type of device for indirect vision, if the requirements of this Directive are not fulfilled.
However, this date shall be postponed by 12 months as regards the requirements concerning a class VI front mirror as a component and its installation on vehicles.
3. With effect from 26 January 2006, Member States shall prohibit the national type-approval for any new type of vehicle on grounds relating to the device for indirect vision if the requirements of this Directive are not fulfilled.
However this date shall be postponed by 12 months as regards the requirements concerning a class VI front mirror as a component and its installation on vehicles.
4. With effect from 26 January 2010 for vehicles of categories M1 and N1, and with effect from 26 January 2007 for all vehicles of other categories, Member States:
— shall consider certificates of conformity which accompany new vehicles in accordance with the provisions of Directive 70/156/EEC to be no longer valid for the purposes of Article 7(1) of that Directive,
— shall prohibit the sale, registration or entry into service of vehicles,
4. on grounds relating to the device for indirect vision if the vehicles do not comply with the requirements of this Directive.
5. With effect from 26 January 2010 for vehicles of categories M1 and N1, and with effect from 26 January 2007, for all vehicles of other categories, the requirements of this Directive relating to the device for indirect vision as a component shall apply for the purposes of Article 7(2) of Directive 70/156/EEC.
6. Notwithstanding paragraphs 2 and 5, for the purposes of replacement parts, Member States shall continue to grant EC type-approval and to permit the sale and entry into service of components or separate technical units intended for use on vehicle types which have been approved before 26 January 2007, pursuant to Directive 71/127/EEC and, where applicable, subsequent extensions to those approvals.
7. Notwithstanding paragraph 3, Member States may continue to grant national type-approval for any new type of articulated vehicle of category M2 and M3, class I, as defined in Annex I, point 2.1.1.1 to Directive 2001/85/EC ( 6 ), composed of at least three articulated rigid parts, which do not comply with the provisions of this Directive, provided that the requirements for the driver's field of vision are respected as referred in Annex III, point 5 to this Directive.
8. The provisions laid down in this Directive shall also contribute to establishing a high level of protection in the context of the international harmonisation of legislation in this area. Therefore, as soon as possible after the adoption of this Directive, the Commission shall submit a proposal to the United Nations Economic Commission for Europe with the aim of aligning the provisions of UNECE Regulation 46 with the provisions of this Directive.
Article 3
By 26 January 2010, the Commission shall carry out a detailed study to ascertain whether the amendments introduced by this Directive are having a positive effect on road safety, in particular as regards pedestrians, cyclists and other vulnerable road users. On the basis of those findings, the Commission shall, if necessary, propose additional legislative measures for further improvement of the field of indirect vision.
Article 4
Directive 70/156/EEC is hereby amended as follows:
1. in Annex I, point 9.9 is replaced by the following:
‘9.9. Devices for indirect vision
9.9.1. |
Mirrors (state for each mirror): … 9.9.1.1. Make: … 9.9.1.2. EC type-approval mark: … 9.9.1.3. Variant: … 9.9.1.4. Drawing(s) for the identification of the mirror showing the position of the mirror relative to the vehicle structure: … 9.9.1.5. Details of the method of attachment including that part of the vehicle structure to which it is attached: … 9.9.1.6. Optional equipment which may affect the rearward field of vision: … 9.9.1.7. A brief description of the electronic components (if any) of the adjustment system: … |
9.9.2. |
Devices for indirect vision other than mirrors: …
|
2. in Annex III, point 9.9 is replaced by the following:
‘9.9. Devices for indirect vision
9.9.1. |
Mirrors (state for each mirror): … 9.9.1.1. Make: … 9.9.1.2. EC type-approval mark: … 9.9.1.3. Variant: … 9.9.1.4. Drawing(s) for the identification of the mirror showing the position of the mirror relative to the vehicle structure: … 9.9.1.5. Details of the method of attachment including that part of the vehicle structure to which it is attached: … 9.9.1.6. Optional equipment which may affect the rearward field of vision: … 9.9.1.7. A brief description of the electronic components (if any) of the adjustment system: … |
9.9.2. |
Devices for indirect vision other than mirrors: …
|
3. Annex IV is hereby amended as follows:
— Part I, point 8 of the table shall be replaced by the following:
—
‘Subject |
Directive number |
Official Journal reference |
Applicability |
|||||||||
M1 |
M2 |
M3 |
N1 |
N2 |
N3 |
O1 |
O2 |
O3 |
O4 |
|||
… |
||||||||||||
8. Indirect vision devices |
2003/97/EC |
L 25 of 29.1.2004 |
X |
X |
X |
X |
X |
X’ |
— in point 8 of Part I, the term ‘rear-view mirrors’ shall be replaced by ‘devices for indirect vision’,
— in point 8 of Part II, the term ‘rear-view mirrors’ shall be replaced by ‘devices for indirect vision’;
4. in point 8 of Appendices 1 and 2 to Annex XI, the term ‘rear-view mirrors’ shall be replaced by ‘devices for indirect vision’.
Article 5
1. Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with this Directive before 24 January 2005. They shall forthwith inform the Commission thereof.
When Member States adopt these measures, they shall contain a reference to this Directive or be accompanied by such reference on the occasion of their official publication. The methods of making such reference shall be laid down by the Member States.
2. Member States shall communicate to the Commission the text of the main provisions of national law which they adopt in the field covered by this Directive.
Article 6
Directive 71/127/EEC shall be repealed with effect from 24 January 2010.
References to the repealed Directive shall be construed as being made to this Directive and shall be read in accordance with the correlation table set out in Annex IV.
Article 7
This Directive shall enter into force on the day of its publication in the Official Journal of the European Union.
Article 8
This Directive is addressed to the Member States.
LIST OF ANNEXES
Annex I |
Definitions and administrative provisions for EC type-approval |
|
Appendix 1 |
Information document relating to EC type-approval of a device for indirect vision |
|
Appendix 2 |
Model EC component type-approval certificate for a device for indirect vision |
|
Appendix 3 |
Information document relating to EC type-approval of a vehicle |
|
Appendix 4 |
Model EC type-approval certificate for a vehicle with regard to the installation of devices for indirect vision |
|
Appendix 5 |
EC component type-approval mark |
|
Appendix 6 |
Procedure for determining the H point and verifying the relative positions of the R and H points |
|
Annex II |
Design specifications and tests required for EC component type-approval of a device for indirect vision. |
|
Appendix 1 |
Procedure for determining the radius of curvature ‘r’ of the reflecting surface of a mirror |
|
Appendix 2 |
Test method for determining reflectivity |
|
Annex III |
Requirements concerning the fitting of mirrors and other devices for indirect vision to vehicles. |
|
Appendix |
Calculation of the detection distance. |
|
Annex IV |
Correlation table provided for in Article 6. |
ANNEX I
DEFINITIONS AND ADMINISTRATIVE PROVISIONS FOR EC TYPE-APPROVAL
1. DEFINITIONS
1.1. |
‘Devices for indirect vision’ means devices to observe the traffic area adjacent to the vehicle which cannot be observed by direct vision. These can be conventional mirrors, camera-monitors or other devices able to present information about the indirect field of vision to the driver.
|
1.2. |
‘Vehicles of categories M1, M2, M3, N1, N2, N3’ means those defined in Annex II, Part A to Directive 70/156/EEC.
|
2. APPLICATION FOR EC COMPONENT TYPE-APPROVAL OF A DEVICE FOR INDIRECT VISION
2.1. |
The application for EC component type-approval for a type of device for indirect vision shall be made by the manufacturer. |
2.2. |
The model information document is reproduced in Appendix 1 to this Annex. |
2.3. |
For each type of device for indirect vision the application shall be accompanied by: 2.3.1. In case of mirrors, four samples: three for use in the tests and one to be retained by the laboratory for any further examination that might subsequently prove necessary. Additional specimens may be called for at the request of the laboratory. 2.3.2. In case of other devices for indirect vision, one sample of all the parts. |
3. INSCRIPTIONS
Specimens of a type of mirror or device for indirect vision other than a mirrorsubmitted for EC component type-approval must bear the applicant's clearly visible and indelible trade mark or name and must allow sufficient space for the inscription of the EC component type-approval mark; this space must be indicated in the diagrams referred to in point 1.2.1.2 of Appendix 1 to this Annex.
4. APPLICATION FOR EC TYPE-APPROVAL OF A VEHICLE WITH REGARD TO THE INSTALLATION OF THE DEVICES FOR INDIRECT VISION
4.1. |
The application for EC vehicle type-approval with regard to devices for indirect vision shall be made by the manufacturer. |
4.2. |
The model information document is reproduced in Appendix 3 to this Annex. |
4.3. |
For each type of vehicle the application shall be accompanied by: 4.3.1. A vehicle representative of the type, the vehicle being if necessary determined by agreement with the technical department responsible for conducting the tests. |
5. EC COMPONENT TYPE-APPROVAL
5.1. Once the relevant requirements have been met, EC component type-approval shall be granted and a component type-approval number, in accordance with Annex VII to Directive 70/156/EEC, issued in respect of any mirror or device for indirect vision other than a mirror.
5.2. This number shall not be assigned to any other type of device for indirect vision.
5.3. The model EC type-approval certificate is reproduced in Appendix 2 to this Annex.
6. MARKING
Any device for indirect vision conforming to a type in respect of which component type-approval has been granted pursuant to this Directive shall bear an EC component type-approval mark as specified in Appendix 5.
7. EC VEHICLE TYPE-APPROVAL
7.1. Once the relevant requirements have been met, EC vehicle type-approval shall be granted in respect of any type of vehicles.
7.2. The model EC type-approval certificate is reproduced in Appendix 4 to this Annex.
7.3. A type-approval number in accordance with Annex VII of Directive 70/156/EEC is assigned to each vehicle type. The same Member State must not assign the same number to another vehicle type.
8. TYPE MODIFICATIONS AND AMENDMENTS TO THE APPROVALS
8.1. Where type modifications are made to the type of vehicle or type of device for indirect vision approved pursuant to this Directive, the provisions of Article 5 of Directive 70/156/EEC shall apply.
9. CONFORMITY OF PRODUCTION (VEHICLES AND COMPONENTS)
9.1. Measures to ensure conformity of production must be taken in accordance with the provisions laid down in Article 10 of Directive 70/156/EEC.
Appendix 1
Information document No … relating to EC type-approval of a device for indirect vision
Directive 2003/97/EC of the European Parliament and of the Council
The following information, if applicable, must be supplied in triplicate and must include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 on a folder of A4 format. Photographs, if any, must show sufficient detail.
0. GENERAL
0.1. Make (trade name of manufacturer): …
0.2. Type: …
0.3. Means of identification of the type, if indicated on the device: …
0.4. Category of vehicle for which the device is intended: …
0.5. Name and address of manufacturer: …
0.7. Location of and method of affixing the EC type-approval mark: …
0.8. Address(es) of the production plant(s): …
1. DEVICE FOR INDIRECT VISION
1.1. |
Mirrors (state for each mirror) 1.1.3. Variant: … 1.1.4. Drawing(s) for the identification of the mirror: … 1.1.5. Details of the method of attachment: … |
1.2. |
Devices for indirect vision other than mirrors
|
Appendix 2
Model EC component type-approval certificate for a device for indirect vision
Notification concerning the grant, refusal, withdrawal or extension of EC component type-approval for a type of device for indirect vision
EC component type-approval No: …
1. |
Trade name or mark: … |
2. |
Identification of the devices: mirror, camera/monitor, other device ( 8 ): — in the case of a mirror Class (I, II, III, IV, V, VI) ( 9 ) … — in the case of a camera/monitor or other device for indirect vision (S) ( 10 ) … |
3. |
Name and address of manufacturer: … |
4. |
If applicable, name and address of manufacturer's authorised representative: … |
5. |
Symbol |
6. |
Submitted for type-approval on: … |
7. |
Test laboratory: … |
8. |
Date and number of laboratory report: … |
9. |
Date of grant/refusal/withdrawal/extension of EC component type-approval ( 12 ): … |
10. |
Place: … |
11. |
Date: … |
12. |
The following documents, bearing the type-approval number shown above, are annexed to this type-approval certificate: … … … … … (Descriptive notes, drawings, diagrams and plans) These documents must be supplied to the competent authorities of the other Member States at their express request. Remarks, if any, particularly as regards restrictions on use and/or conditions for fitting: … … … … … … (Signature) |
Appendix 3
Information document No … relating to EC type-approval of a vehicle
Directive 2003/97/EC of the European Parliament and of the Council
The following information, if applicable, must be supplied in triplicate and must include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 on a folder of A4 format. Photographs, if any, must show sufficient detail.
0. GENERAL
0.1. |
Make (trade name of manufacturer): … |
0.2. |
Type: … 0.2.1. Commercial description (if applicable): … |
0.3. |
Means of identification of the type, if indicated on the vehicle: … 0.3.1. Location of that marking: … |
0.4. |
Category of vehicle ( 13 ): … |
0.5. |
Name and address of manufacturer: … |
0.8. |
Address(es) of the production plant(s): … |
1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1. |
Photographs and/or drawings of a representative vehicle: … |
1.7. |
Driving cab (forward control or bonneted) ( 14 ): … |
1.8. |
Driving position: left/right ( 15 ): … 1.8.1. Vehicle is equipped to be driven in right-hand/left-hand traffic ( 16 ): … |
2.4. |
Range of vehicle dimensions (overall): …
|
9. |
BODYWORK
|
Appendix 4
Model EC type-approval certificate for a vehicle with regard to the installation of devices for indirect vision
Articles 4(2) and 10 of Council Directive 70/156/EEC of 6 February 1970 on the approximation of the laws of the Member States relating to the type-approval of motor vehicles and their trailers
EC type-approval No: … extension ( 17 )
1. |
Trade name or mark of vehicle: … … |
2. |
Type of vehicle: … |
3. |
Category of vehicle (M1, M2, M3, N1, N2≤ 7,5 t, N2> 7,5 t, N3) ( 18 ) 3.1. Type of category N3 vehicle: rigid lorry/trailer/semi-trailer ( 19 ) |
4. |
Name and address of manufacturer: … … |
5. |
If applicable, name and address of authorised representative: … … |
6. |
Trade name or mark of mirrors and supplementary devices for indirect vision and component type-approval number:… … |
7. |
Class(es) of mirrors and devices for indirect vision (I, II, III, IV, V, VI, S) ( 20 ) |
8. |
Extension of EC type-approval of the vehicle to cover the following device for indirect vision: … … … |
9. |
Data for identification of the R point of the driver's seating position: … … |
10. |
Maximum and minimum bodywork widths in respect of which the mirror and the device for indirect vision has been granted type-approval (in the case of chassis/cabs referred to in point 3.3 of Annex III): … … … … |
11. |
Vehicle submitted for EC type-approval on: … |
12. |
Technical department responsible for checking conformity for the purpose of EC type-approval: … … |
13. |
Date of report issued by that department: … |
14. |
Number of report issued by that department: … |
15. |
EC type-approval in respect of the installation of devices for indirect vision has been granted/refused ( 21 ) |
16. |
An extension of EC type-approval in respect of the installation of devices for indirect vision has been granted/refused ( 22 ) |
17. |
Place: … |
18. |
Date: … |
19. |
Signature: … |
20. |
The following documents, bearing the type-approval number shown above, are annexed to this certificate: — drawings showing the mountings of the devices for indirect vision; — drawings and plans showing the mounting positions and characteristics of the part of the structure where the devices for indirect vision are mounted; — general view from the front, the rear and the passenger compartment showing where the devices for indirect vision are fitted. These documents must be supplied to the competent authorities of the other Member States at their express request. |
Appendix 5
EC component type-approval mark
1. GENERAL
1.1. The EC component type-approval mark shall consist of a rectangle surrounding the lower case letter ‘e’ followed by the distinguishing number of the Member State which has granted the component type-approval: 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, ►M1 7 for Hungary, 8 for the Czech Republic, ◄ 9 for Spain, 11 for the United Kingdom, 12 for Austria, 13 for Luxembourg, 17 for Finland, 18 for Denmark, ►M1 20 for Poland, ◄ 21 for Portugal, 23 for Greece, 24 for Ireland ►M1 , 26 for Slovenia, 27 for Slovakia, 29 for Estonia, 32 for Latvia, 36 for Lithuania, 49 for Cyprus, 50 for Malta ◄ . It must also include in the vicinity of the rectangle the EC component type-approval number. This number shall consist of the component type-approval number shown on the certificate completed for the type (see Appendix 3), preceded by two figures indicating the sequence number of the latest amendment to this Directive on the date EC component type-approval was granted. The amendment sequence number and the component type-approval number shown on the certificate shall be separated by an asterisk. In this Directive the sequence number is 03.
1.2. The EC component type-approval mark shall be completed by the addition of the symbol I or II or III or IV or V or VI, specifying the class to which the type of mirror belongs or the symbol S in case of any device for indirect vision other than a mirror. The additional symbol shall be placed in any convenient position in the vicinity of the rectangle containing the letter ‘e’.
1.3. The EC component type-approval mark and the additional symbol shall be indelibly inscribed on an integral part of the mirror or any other device for indirect vision other than a mirror in such a way as to be clearly visible even after the mirror or other device for indirect vision has been mounted on a vehicle.
2. EXAMPLES OF THE EC COMPONENT TYPE-APPROVAL MARK
2.1. |
Five examples of EC component type-approval marks, completed by the additional symbol are given below. |
Example No 1
The mirror bearing the EC component type-approval mark shown above is a Class I mirror (interior rear-view), which has been approved in France (e2) under number 03*3500. Example No 2
The mirror bearing the EC component type-approval mark shown above is a Class II mirror (exterior rear-view), which has been approved in the Netherlands (e4) under the number 03*1870. Example No 3
The mirror bearing the EC component type-approval mark shown above is a Class V mirror (close proximity), which has been approved in Greece (e23) under the number 03*3901. Example No 4
The mirror bearing the EC component type-approval mark shown above is a Class IV mirror (exterior rear-view — wide angle), which has been approved in Italy (e3) under the number 03*1248. Example No 5
Explanation: The device for indirect vision bearing the EC component type-approval mark shown above is a device for indirect vision (S), other than a mirror which has been approved in the Netherlands (e4) under number 03*3002. |
Appendix 6
Procedure for determining the H point and verifying the relative positions of the R and H points
The relevant parts of Annex III to Directive 77/649/EEC are applicable.
Appendix 7
Determination of the ocular points for a seat with a fixed seat-back angle
1. The position of the ocular points in relation to the R point shall be adjusted as indicated in the table below by X coordinates from the three-dimensional reference grid. The table indicates the basic coordinates for a fixed seat-back angle of 25 degrees. The three-dimensional reference grid for the coordinates is as defined in point 2.3 of Annex I to Directive 77/649/EEC as amended.
Seat back angle |
Horizontal coordinates |
(in degrees) |
ΔX |
25 |
68 mm |
2. Further correction for fixed seat-back angles other than 25
The table below indicates the further corrections, from the ocular position with a fixed seat-back angle of 25 degrees, to be made to the X and Z coordinates of the ocular points when the design seat-back angle is not 25 degrees.
Seat-back angle |
Horizontal coordinates |
Vertical coordinates |
(in degrees) |
ΔX |
ΔZ |
5 |
– 186 mm |
28 mm |
6 |
– 177 mm |
27 mm |
7 |
– 167 mm |
27 mm |
8 |
– 157 mm |
27 mm |
9 |
– 147 mm |
26 mm |
10 |
– 137 mm |
25 mm |
11 |
– 128 mm |
24 mm |
12 |
– 118 mm |
23 mm |
13 |
– 109 mm |
22 mm |
14 |
– 99 mm |
21 mm |
15 |
– 90 mm |
20 mm |
16 |
– 81 mm |
18 mm |
17 |
– 72 mm |
17 mm |
18 |
– 62 mm |
15 mm |
19 |
– 53 mm |
13 mm |
20 |
– 44 mm |
11 mm |
21 |
– 35 mm |
9 mm |
22 |
– 26 mm |
7 mm |
23 |
– 18 mm |
5 mm |
24 |
– 9 mm |
3 mm |
25 |
0 mm |
0 mm |
26 |
9 mm |
– 3 mm |
27 |
17 mm |
– 5 mm |
28 |
26 mm |
– 8 mm |
29 |
34 mm |
– 11 mm |
30 |
43 mm |
– 14 mm |
31 |
51 mm |
– 18 mm |
32 |
59 mm |
– 21 mm |
33 |
67 mm |
– 24 mm |
34 |
76 mm |
– 28 mm |
35 |
84 mm |
– 32 mm |
36 |
92 mm |
– 35 mm |
37 |
100 mm |
– 39 mm |
38 |
108 mm |
– 43 mm |
39 |
115 mm |
– 48 mm |
40 |
123 mm |
– 52 mm |
ANNEX II
DESIGN SPECIFICATIONS AND TESTS REQUIRED FOR EC COMPONENT TYPE-APPROVAL OF A DEVICE FOR INDIRECT VISION
A. MIRRORS
1. General specifications
1.1. |
All mirrors must be adjustable. |
1.2. |
The edge of the reflecting surface must be enclosed in a protective housing (holder, etc.) which, on its perimeter, must have a value ‘c’ greater than or equal to 2,5 mm at all points and in all directions. If the reflecting surface projects beyond the protective housing, the radius of curvature ‘c’ on the edge of the projecting part must be not less than 2,5 mm and the reflecting surface must return into the protective housing under a force of 50 N applied to the point of greatest projection, relative to the protective housing, in a horizontal direction, approximately parallel to the longitudinal median plane of the vehicle. |
1.3. |
When the mirror is mounted on a plane surface, all parts, irrespective of the adjustment position of the device, including those parts remaining attached to the support after the test provided for in point 4.2, which are in potential, static contact with a sphere either 165 mm in diameter in the case of an interior mirror or 100 mm in diameter in the case of an exterior mirror, must have a radius of curvature ‘c’ of not less than 2,5 mm. 1.3.1. Edges of fixing holes or recesses of which the diameter or longest diagonal is less than 12 mm are exempt from the radius requirements of point 1.3 provided that they are blunted. |
1.4. |
The device for the attachment of mirrors to the vehicle must be so designed that a cylinder with a 70 mm radius, having as its axis the axis, or one of the axes, of pivot or rotation which ensures deflection of the mirror in the direction of impact concerned, passes through at least part of the surface to which the device is attached. |
1.5. |
The parts of exterior mirrors referred to in points 1.2 and 1.3 which are made of a material with a Shore A hardness not exceeding 60 are exempt from the relevant provisions. |
1.6. |
In the case of those parts of interior mirrors which are made of a material with a Shore A hardness of less than 50 and which are mounted on a rigid support, the requirements of points 1.2 and 1.3 shall only apply to the support. |
2. Dimensions
2.1. Interior rear-view mirrors (Class I)
The dimensions of the reflecting surface must be such that it is possible to inscribe thereon a rectangle one side of which is 40 mm and the other ‘a’ mm in length, where
and r is the radius of curvature.
2.2. Main exterior rear-view mirrors (Classes II and III)
2.2.1. The dimensions of the reflecting surface must be such that it is possible to inscribe therein:
— a rectangle 40 mm high the base length of which, measured in millimetres, has the value ‘a’;
— a segment which is parallel to the height of the rectangle and the length of which, expressed in millimetres, has the value ‘b’.
2.2.2. The minimum values of ‘a’ and ‘b’ are given in the table below:
Class of rear-view mirror |
a [mm] |
b [mm] |
II |
|
200 |
III |
|
70 |
2.3. ‘Wide-angle’ exterior mirrors (Class IV)
The contours of the reflecting surface must be of simple geometric form and its dimensions such that it provides, if necessary in conjunction with a Class II exterior mirror, the field of vision specified in point 5.4 of Annex III.
2.4. ‘Close-proximity’ exterior mirrors (Class V)
The contours of the reflecting surface must be of simple geometric form and its dimensions such that the mirror provides the field of vision specified in point 5.5 of Annex III.
2.5. Front mirrors (Class VI)
The contours of the reflecting surface must be of simple geometric form and its dimensions such that the mirror provides the field of vision specified in point 5.6 of Annex III.
3. Reflecting surface and coefficients of reflection
3.1. |
The reflecting surface of a mirror must be either flat or spherically convex. Exterior mirrors may be equipped with an additional aspherical part provided that the main mirror fulfils the requirements of the indirect field of vision. |
3.2. |
Differences between the radii of curvature of mirrors 3.2.1. The difference between ri or r′i, and rp at each reference point must not exceed 0,15 r. 3.2.2. The difference between any of the radii of curvature (rp1, rp2, and rp3) and r must not exceed 0,15 r. 3.2.3. When r is not less than 3 000 mm, the value of 0,15 r quoted in points 3.2.1 and 3.2.2 is replaced by 0,25 r. |
3.3. |
Requirements for aspherical parts of mirrors 3.3.1. Aspherical mirrors shall be of sufficient size and shape to provide useful information to the driver. This normally means a minimum width of 30 mm at some point. 3.3.2. The radius of curvature ri of the aspherical part shall not be less than 150 mm. |
3.4. |
Value of ‘r’ for spherical mirrors must not be less than: 3.4.1. 1 200 mm for interior rear-view mirrors (Class I); 3.4.2. 1 200 mm for Class II and III main exterior rear-view mirrors; 3.4.3. 300 mm for ‘wide-angle’ exterior mirrors (Class IV) and ‘close-proximity’ exterior mirrors (Class V); 3.4.4. 200 mm for front mirrors (Class VI). |
3.5. |
The value of the normal coefficient of reflection, as determined according to the method described in Appendix 1 to this Annex, must be not less than 40 %. In the case of reflecting surfaces with a changeable degree of reflection, the ‘day’ position must allow the colours of the signals used for road traffic to be recognised. The value of the normal coefficient of reflection in the ‘night’ position must be not less than 4 %. |
3.6. |
The reflecting surface must retain the characteristics laid down in point 3.5 in spite of prolonged exposure to adverse weather conditions in normal use. |
4. Tests
4.1. |
Mirrors shall be subjected to the tests described in point 4.2.
|
4.2. |
Impact test The test according to this paragraph is not to be carried out for devices integrated in the bodywork of the vehicle and providing a frontal deflecting area of an angle not more than 45 ° measured in relation to the longitudinal median plane of the vehicle, or devices not protruding more than 100 mm measured beyond the circumscribing bodywork of the vehicle according to 74/483/EEC. 4.2.1. Description of the test rig
4.2.2. Description of the test
|
5. Results of the test
5.1. |
In the tests described in point 4.2, the pendulum must continue to swing after impact in such a way that the projection of the position assumed by the arm on the plane of release makes an angle of at least 20 ° with the vertical. The accuracy of measurement of the angle shall be within ± 1 °. 5.1.1. This requirement is not applicable to mirrors stuck to the windscreen, in respect of which the requirement stipulated in point 5.2 shall apply after the test. 5.1.2. The required angle to the vertical is reduced from 20 ° to 10 ° for all Class II and Class IV rear-view mirrors and for Class III rear-view mirrors which are attached to the same mounting as Class IV mirrors. |
5.2. |
Should the mounting of the mirror break during the tests described in point 4.2 for mirrors stuck to the windscreen, the part remaining must not project beyond the base by more than 10 mm and the configuration remaining after the test must satisfy the conditions laid down in point 1.3. |
5.3. |
The reflecting surface must not break during the tests described in point 4.2. However breakage of the reflecting surface will be allowed if one of the following conditions is fulfilled: 5.3.1. The fragments of glass still adhere to the back of the housing or to a surface firmly attached to the housing; partial separation of the glass from its backing is admissible provided this does not exceed 2,5 mm on either side of the cracks. It is permissible for small splinters to become detached from the surface of the glass at the point of impact; 5.3.2. The reflecting surface is made of safety glass. |
B. DEVICES FOR INDIRECT VISION OTHER THAN MIRRORS
1. General requirements
1.1. If adjustment by the user is needed, the device for indirect vision shall be adjustable without the use of tools.
1.2. If a device for indirect vision can only render the total prescribed field of vision by scanning the field of vision, the total process of scanning, rendering and reset to its initial position together shall not take more than two seconds.
2. Camera-monitor devices for indirect vision
2.1. General requirements
2.1.1. When the camera-monitor device for indirect vision is mounted on a plane surface, all parts, irrespective of the adjustment position of the device which are in potential, static contact with a sphere either 165 mm in diameter in the case of a monitor or 100 mm in diameter in the case of a camera, must have a radius of curvature ‘c’ of not less than 2,5 mm.
2.1.2. Edges of fixing holes or recesses of which the diameter or longest diagonal is less than 12 mm are exempt from the radius requirements of point 2.1.1 provided that they are blunted.
2.1.3. For parts of the camera and the monitor which are made of a material with a Shore A hardness of less than 60 and which are mounted on a rigid support, the requirements of point 2.1.1 shall only apply to the support.
2.2. Functional requirements
2.2.1. The camera should function well under low sunlight conditions. The camera shall provide a luminance contrast of at least 1:3 under low sun condition in a region outside the part of the image where the light source is reproduced (condition as defined in EN 12368:8.4). The light source shall illuminate the camera with 40 000 lx. The angle between the normal of the sensor plane and the line connecting the midpoint of the sensor and the light source shall be 10 °.
2.2.2. The monitor shall render a minimum contrast under various light conditions as specified by draft international standard ISO/DIS 15008 [2].
2.2.3. It shall be possible to adjust the average luminance of the monitor either manually or automatically to the ambient conditions.
2.2.4. The measurements for the luminance contrast shall be carried out according to ISO/DIS 15008.
3. Other devices for indirect vision
It has to be proved that the device meets the following requirements:
3.1. The device shall perceive the visual spectrum and shall always render this image without the need for interpretation into the visual spectrum.
3.2. The functionality shall be guaranteed under the circumstances of use in which the system shall be put into service. Depending on the technology used in obtaining images and presenting them point 2.2 shall be entirely or partly applicable. In other cases this can be achieved by establishing and demonstrating by means of system sensitivity analogous to point 2.2 that a function is ensured that is comparable to or better than what is required for and by demonstrating that a functionality is guaranteed that is equivalent or better than that required for mirror- or camera-monitor devices for indirect vision.
Appendix 1
Procedure for determining the radius of curvature ‘r’ of the reflecting surface of a mirror
1. Measurement
1.1. Equipment
A ‘spherometer’ similar to the one described in Figure 3 having the indicated distances between the tracing pin of the dial gauge and the fixed legs of the bar is used.
1.2. Measuring points
1.2.1. The principal radii of curvature shall be measured at three points situated as close as possible to positions at one-third, one-half and two-thirds of the distance along the arc of the reflecting surface passing through the centre of this surface and parallel to segment b, or of the arc passing through the centre of the reflecting surface which is perpendicular to it if this arc is the longer.
1.2.2. Where, owing to the size of the reflecting surface, it is impossible to obtain measurements in the directions defined in point 1.1.1.5 of Annex I, the technical services responsible for the tests may take measurements at the said point in two perpendicular directions as close as possible to those prescribed above.
2. Calculation of the radius of curvature ‘r’
‘r’ expressed in mm is calculated from the formula:
where:
rp1 |
: |
the radius of curvature at the first measuring point, |
rp2 |
: |
the radius of curvature at the second measuring point, |
rp3 |
: |
the radius of curvature at the third measuring point. |
Figure 3: spherometer
Appendix 2
Test method for determining reflectivity
1. DEFINITIONS
1.1. CIE standard illuminate A ( 23 ): Colorimetric illuminate, respecting the full radiator at T68 = 2 855,6 K.
1.2. CIE standard source A ( 24 ): Gas-filled tungsten filament lamp operating at a correlated colour temperature of T68= 2 855,6 K.
1.3. CIE 1931 standard colorimetric observer (
25
): Receptor of radiation whose colorimetric characteristics correspond to the spectral tristimulus values(λ),
(λ),
(λ) (see table).
1.4. CIE spectral tristimulus values ( 26 ): Tristimulus values of the spectral components of an equi-energy spectrum in the CIE (XYZ) system.
1.5. Photopic vision ( 27 ): Vision by the normal eye when it is adapted to levels of luminance of at least several cd/m2.
2. APPARATUS
2.1. General
The apparatus shall consist of a light source, a holder for the test sample, a receiver unit with a photodetector and an indicating meter (see Figure 4), and means of eliminating the effects of extraneous light.
The receiver may incorporate a light-integrating sphere to facilitate measuring the reflectance of non-flat (convex) mirrors (see Figure 5).
2.2. Spectral characteristics of light source and receiver
The light source shall consist of a CIE standard source A and associated optics to provide a near-collimated light beam. A voltage stabiliser is recommended in order to maintain a fixed lamp voltage during instrument operation.
The receiver shall have a photodetector with a spectral response proportional to the photopic luminosity function of the CIE (1931) standard colorimetric observer (see table). Any other combination of illuminate-filter-receptor giving the overall equivalent of CIE standard illuminate A and photopic vision may be used. When an integrating sphere is used in the receiver, the interior surface of the sphere shall be coated with a matt (diffusive) spectrally non-selective white coating.
2.3. Geometrical conditions
The angle of the incident beam (θ) should preferably be 0,44 ± 0,09 rad (25 ± 5 °) from the perpendicular to the test surface and shall not exceed the upper limit of the tolerance (i.e. 0,53 rad or 30 °). The axis of the receptor shall make an angle (θ) with this perpendicular equal to that of the incident beam (see Figure 4). The incident beam upon arrival at the test surface shall have a diameter of not less than 13 mm (0,5 in.). The reflected beam shall not be wider than the sensitive area of the photodetector, shall not cover less than 50 % of such area, and as nearly as possible shall cover the same area segment as used during instrument calibration.
When an integrating sphere is used in the receiver section, the sphere shall have a minimum diameter of 127 mm (5 in.). The sample and incident beam apertures in the sphere wall shall be of such a size as to admit the entire incident and reflected light beams. The photodetector shall be so located as not to receive direct light from either the incident or the reflected beam.
2.4. Electrical characteristics of the photodetector-indicator unit
The photodetector output as read on the indicating meter shall be a linear function of the light intensity of the photosensitive area. Means (electrical and/or optical) shall be provided to facilitate zeroing and calibration adjustments. Such means shall not affect the linearity or the spectral characteristics of the instrument. The accuracy of the receptor-indicator unit shall be within ± 2 % of full scale, or ± 10 % of the magnitude of the reading, whichever is the smaller.
2.5. Sample holder
The mechanism shall be capable of locating the test sample so that the axes of the source arm and receptor intersect at the reflecting surface. The reflecting surface may lie within or at either face of the mirror sample, depending on whether it is a first-surface, second-surface or prismatic ‘flip’-type mirror.
3. PROCEDURE
3.1. Direct calibration method
In the direct calibration method, air is used as the reference standard. This method is applicable for those instruments, which are so constructed as to permit calibration at the 100 % point by swinging the receiver to a position directly on the axis of the light source (see Figure 4).
It may be desired in some cases (such as when measuring low-reflectivity surfaces) to use an intermediate calibration point (between 0 and 100 % on the scale) with this method. In these cases, a neutral density filter of known transmittance shall be inserted in the optical path, and the calibration control shall then be adjusted until the meter reads the percentage transmission of the neutral density filter. This filter shall be removed before reflectivity measurements are performed.
3.2. Indirect calibration method
The indirect calibration method is applicable in the case of instruments with fixed source and receiver geometry. A properly calibrated and maintained reflectance standard is required. This reference standard should preferably be a flat mirror with a reflectance value as near as possible to that of the test samples.
3.3. Flat mirror measurement
The reflectance of flat mirror samples can be measured on instruments employing either the direct or the indirect calibration method. The reflectance value is read directly from the indicating meter.
3.4. Non-flat (convex) mirror measurement
Measurement of the reflectance of non-flat (convex) mirrors requires the use of instruments which incorporate an integrating sphere in the receiver unit (see Figure 5). If the instrument-indicating meter indicates ne divisions with a standard mirror of E % reflectance, then, with a mirror of unknown reflectance, nx divisions will correspond to a reflectance of X %, in accordance with the formula:
Figure 4: Generalised reflectometer showing experimental set-ups for the two calibration methods
Figure 5: Generalised reflectometer, incorporating an integrating sphere in the receiver
Spectral tristimulus values for the CIE 1931 standard colorimetric observer ( 28 )
This table is taken from CIE publication 50 (45) (1970)
λ nm |
|
|
|
380 |
0,0014 |
0,0000 |
0,0065 |
390 |
0,0042 |
0,0001 |
0,0201 |
400 |
0,0143 |
0,0004 |
0,0679 |
410 |
0,0435 |
0,0012 |
0,2074 |
420 |
0,1344 |
0,0040 |
0,6456 |
430 |
0,2839 |
0,0116 |
1,3856 |
440 |
0,3483 |
0,0230 |
1,7471 |
450 |
0,3362 |
0,0380 |
1,7721 |
460 |
0,2908 |
0,0600 |
1,6692 |
470 |
0,1954 |
0,0910 |
1,2876 |
480 |
0,0956 |
0,1390 |
0,8130 |
490 |
0,0320 |
0,2080 |
0,4652 |
500 |
0,0049 |
0,3230 |
0,2720 |
510 |
0,0093 |
0,5030 |
0,1582 |
520 |
0,0633 |
0,7100 |
0,0782 |
530 |
0,1655 |
0,8620 |
0,0422 |
540 |
0,2904 |
0,9540 |
0,0203 |
550 |
0,4334 |
0,9950 |
0,0087 |
560 |
0,5945 |
0,9950 |
0,0039 |
570 |
0,7621 |
0,9520 |
0,0021 |
580 |
0,9163 |
0,8700 |
0,0017 |
590 |
1,0263 |
0,7570 |
0,0011 |
600 |
1,0622 |
0,6310 |
0,0008 |
610 |
1,0026 |
0,5030 |
0,0003 |
620 |
0,8544 |
0,3810 |
0,0002 |
630 |
0,6424 |
0,2650 |
0,0000 |
640 |
0,4479 |
0,1750 |
0,0000 |
650 |
0,2835 |
0,1070 |
0,0000 |
660 |
0,1649 |
0,0610 |
0,0000 |
670 |
0,0874 |
0,0320 |
0,0000 |
680 |
0,0468 |
0,0170 |
0,0000 |
690 |
0,0227 |
0,0082 |
0,0000 |
700 |
0,0114 |
0,0041 |
0,0000 |
710 |
0,0058 |
0,0021 |
0,0000 |
720 |
0,0029 |
0,0010 |
0,0000 |
730 |
0,0014 |
0,0005 |
0,0000 |
740 |
0,0007 |
0,0002 (*) |
0,0000 |
750 |
0,0003 |
0,0001 |
0,0000 |
760 |
0,0002 |
0,0001 |
0,0000 |
770 |
0,0001 |
0,0000 |
0,0000 |
780 |
0,0000 |
0,0000 |
0,0000 |
(*) Changed in 1966 (from 3 to 2) |
ANNEX III
REQUIREMENTS CONCERNING THE FITTING OF MIRRORS AND OTHER DEVICES FOR INDIRECT VISION TO VEHICLES
General
1.1. Mirrors and other devices for indirect vision must be fitted in such a way that the mirror or other device does not move so as significantly to change the field of vision as measured or vibrate to an extent which would cause the driver to misinterpret the nature of the image perceived.
1.2. The conditions laid down in item 1.1 must be maintained when the vehicle is moving at speeds of up to 80 % of its maximum design speed, but not exceeding 150 km/h.
1.3. The fields of vision defined below shall be established using ambinocular vision, the eyes being at the ‘driver's ocular points’ as defined in Annex I, point 1.1.1.12. The fields of vision shall be determined when the vehicle is in running order as defined in Directive 97/27/EC, Annex I, point 2.5. They shall be established through windows which have a total light transmission factor of at least 70 % measured normal to the surface.
Mirrors
2. Number
2.1. Minimum number of compulsory mirrors
2.1.1. |
The fields of vision prescribed in point 5 shall be obtained from the minimum number on mandatory mirrors set out in the following table. Where the presence of a mirror is not requested on a mandatory base, this means that no other system for indirect vision can be requested on a mandatory base.
|
2.1.2. |
In case the described field of vision of a front mirror prescribed in point 5.6 can be obtained by another device for indirect vision that is approved according to Annex II, part B and that is installed according to this Annex, this device can be used instead of a mirror. In case a camera/monitor device is used the monitor must exclusively show the field of vision prescribed in point 5.6 while the vehicle is moving forward with a speed up to 30 km/h. In case the vehicle is moving with higher speed or moving backwards the monitor can be used to display the field of vision of other cameras mounted to the vehicle. |
2.2. |
The provisions of this Directive do not apply to the surveillance mirrors defined in point 1.1.1.3 of Annex I. Nevertheless, the exterior surveillance mirrors must be mounted at least 2 m above the ground when the vehicle is under a load corresponding to its maximum technical permissible mass. |
3. Position
3.1. |
Mirrors must be so placed that the driver, when sitting on the driving seat in a normal driving position, has a clear view of the road to the rear, side(s) or front of the vehicle. |
3.2. |
Exterior mirrors shall be visible through the side windows or through the portion of the windscreen that is swept by the windscreen wiper. Nevertheless, for design reasons, this last provision (i.e. the provisions relating the cleaned part of the windscreen) shall not apply to: — exterior mirrors on the passenger side of vehicles of categories M2 and M3; — Class VI mirrors. |
3.3. |
In the case of any vehicle, which is in chassis/cab form when the field of vision is measured, the minimum and maximum body widths shall be stated by the manufacturer and, if necessary, simulated by dummy headboards. All vehicles and mirror configurations taken into consideration during the tests shall be shown on the EC type-approval certificate for a vehicle with regard to the installation of mirrors (see Appendix 4 to Annex I). |
3.4. |
The prescribed exterior mirror on the driver's side of the vehicle must be so located that an angle of not more than 55° is formed between the vertical longitudinal median plane of the vehicle and the vertical plane passing through the centre of the mirror and through the centre of the straight line 65 mm long which joins the driver's two ocular points. |
3.5. |
Mirrors must not project beyond the external bodywork of the vehicle substantially more than is necessary to comply with the requirements concerning fields of vision laid down in point 5. |
3.6. |
Where the lower edge of an exterior mirror is less than 2 m above the ground when the vehicle is loaded to its technically permissible maximum laden mass, this mirror must not project more than 250 mm beyond the overall width of the vehicle measured without mirrors. |
3.7. |
Class V and Class VI mirrors shall be mounted on vehicles in such a way that, regardless of their position after adjustment, no part of these mirrors or their holders is less than 2 m from the ground when the vehicle is under a load corresponding to its technically permissible maximum laden mass. These mirrors shall not, however, be mounted on vehicles the cab height of which is such as to prevent compliance with this requirement. In this case an other device for indirect vision is not required. |
3.8. |
Subject to the requirements of points 3.5, 3.6 and 3.7, mirrors may project beyond the permissible maximum widths of vehicles. |
4. Adjustment
4.1. The interior mirror must be capable of being adjusted by the driver from his driving position.
4.2. The exterior mirror situated on the driver's side must be capable of being adjusted from inside the vehicle while the door is closed, although the window may be open. The mirror may, however, be locked in position from the outside.
4.3. The requirements of point 4.2 do not apply to exterior mirrors which, after having been knocked out of alignment, can be returned to their former position without the need for adjustment.
5. Fields of vision
5.1. Interior rear-view mirror (Class I)
The field of vision must be such that the driver can see at least a 20 m wide, flat, horizontal portion of the road centred on the vertical longitudinal median plane of the vehicle and extending from 60 m behind the driver's ocular points (Figure 6) to the horizon.
Figure 6: Field of vision of Class I mirror
5.2. Main exterior rear-view mirrors Class II
5.2.1. Exterior rear-view mirror on the driver's side
The field of vision must be such that the driver can see at least a 5 m wide, flat, horizontal portion of the road, which is bounded by a plane which is parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle on the driver's side of the vehicle and extends from 30 m behind the driver's ocular points to the horizon.
In addition, the road must be visible to the driver over a width of 1 m, which is bounded by a plane parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle starting from a point 4 m behind the vertical plane passing through the driver's ocular points (see Figure 7).
5.2.2. Exterior rear-view mirror on the passenger's side
The field of vision must be such that the driver can see at least a 5 m wide, flat, horizontal portion of the road, which is bounded on the passenger's side by a plane parallel to the median longitudinal vertical plane of the vehicle and passing through the outermost point of the vehicle on the passenger's side and which extends from 30 m behind the driver's ocular points to the horizon.
In addition, the road must be visible to the driver over a width of 1 m, which is bounded by a plane parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle starting from a point 4 m behind the vertical plane passing through the driver's ocular points (see Figure 7).
Figure 7: Field of vision of Class II mirrors
5.3. Main exterior rear-view mirrors Class III
5.3.1. Exterior rear-view mirror on the driver's side
The field of vision must be such that the driver can see at least a 4 m wide, flat, horizontal portion of the road, which is bounded by a plane parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle on the driver's side of the vehicle and extends from 20 m behind the driver's ocular points to the horizon (see Figure 8).
In addition, the road must be visible to the driver over a width of 1 m, which is bounded by a plane parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle starting from a point 4 m behind the vertical plane passing through the driver's ocular points.
5.3.2. Exterior rear-view mirror on the passenger's side
The field of vision must be such that the driver can see at least a 4 m wide flat, horizontal portion of the road which is bounded by a plane parallel to the median longitudinal vertical plane passing through the outermost point of the vehicle on the passenger's side and which extends from 20 m behind the driver's ocular points to the horizon (see Figure 8).
In addition, the road must be visible to the driver over a width of 1 m which is bounded by a plane which is parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle starting from a point 4 m behind the vertical plane passing through the driver's ocular points.
Figure 8: Field of vision of Class III mirrors
5.4. ‘Wide-angle’ exterior mirror (Class IV)
5.4.1. ‘Wide-angle’ exterior mirror on the driver's side
The field of vision must be such that the driver can see at least a 15 m-wide, flat, horizontal portion of the road, which is bounded by a plane parallel to the median longitudinal vertical plane of the vehicle and passing through the outermost point of the vehicle on the driver's side and which extends from at least 10 to 25 m behind the driver's ocular points.
In addition, the road must be visible to the driver over a width of 4,5 m, which is bounded by a plane parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle starting from a point 1,5 m behind the vertical plane passing through the driver's ocular points (see Figure 9).
5.4.2. ‘Wide-angle’ exterior mirror on the passenger's side
The field of vision must be such that the driver can see at least a 15 m-wide, flat, horizontal portion of the road, which is bounded by a plane parallel to the median longitudinal vertical plane of the vehicle and passing through the outermost point of the vehicle on the passenger's side and which extends from at least 10 to 25 m behind the driver's ocular points.
In addition, the road must be visible to the driver over a width of 4,5 m, which is bounded by a plane parallel to the median longitudinal vertical plane and passing through the outermost point of the vehicle starting from a point 1,5 m behind the vertical plane passing through the driver's ocular points (see Figure 9).
Figure 9: Field of vision of Class IV wide-angle mirrors
5.5. ‘Close-proximity’ exterior mirror (Class V)
The field of vision must be such that the driver can see a flat horizontal portion of the road along the side of the vehicle, bounded by the following vertical planes (see Figures 10a and 10b):
5.5.1. |
the plane parallel to the median longitudinal vertical plane of the vehicle which passes through the outermost point of the vehicle cab on the passenger's side; |
5.5.2. |
in the transverse direction, the parallel plane passing at a distance of 2 m in front of the plane mentioned in point 5.5.1; |
5.5.3. |
to the rear, the plane parallel to the vertical plane passing through the driver's ocular points and situated at a distance of 1,75 m behind that plane; |
5.5.4. |
to the front, the plane parallel to the vertical plane passing through the driver's ocular points and situated at a distance of 1 m in front of that plane. If the vertical transverse plane passing through the leading edge of the vehicle bumper is less than 1 m in front of the vertical plane passing through the driver's ocular points, the field of vision shall be limited to that plane. |
5.5.5. |
In case the field of vision described in Figures 10a and 10b can be perceived through the combination of the field of vision from a Class IV wide-angle mirror and that of a Class VI front mirror, the installation of a Class V close proximity mirror is not compulsory. ![]() Figures 10a and 10b: Field of vision of Class V close-proximity mirror |
5.6. Front mirror (Class VI)
5.6.1. |
The field of vision must be such that the driver can see at least a flat horizontal portion of the road, which is bounded by: — one traverse vertical plane through the outermost point of the front of the vehicle-cab — one traverse vertical plane 2 000 mm in front of the vehicle — one longitudinal vertical plane parallel to the longitudinal vertical median plane going though the outermost side of the vehicle at the driver's side and — one longitudinal vertical plane parallel to the longitudinal vertical median plane 2 000 mm outside the outermost side of the vehicle opposite to the driver's side. The front of this field of vision opposite to the driver's side may be rounded off with a radius of 2 000 mm (see Figure 11). The provisions for front mirrors are compulsory for forward-controlled (as defined in Directive 70/156/EEC, Annex I(a), footnote (Z)) vehicles of categories N2> 7,5 t and N3. If vehicles of these categories with other construction characteristics regarding the bodywork cannot fulfil the requirements by using a front mirror, a camera/monitor device shall be used. If either of these options do not provide the adequate field of vision then any other device for indirect vision shall be used. This device must be able to detect an object of 50 cm height and with a diameter of 30 cm within the field defined in Figure 11. ![]() Figure 11: Field of vision of Class VI front mirror |
5.6.2. |
However, if the driver can see, taking into account the obstructions by the A-pillars, a straight line 300 mm in front of the vehicle at a height of 1 200 mm above the road surface and which is situated between a longitudinal vertical plane parallel to the longitudinal vertical median plane going through the outermost side of the vehicle at the driver's side and a longitudinal vertical plane parallel to the longitudinal vertical median plane 900 mm outside the outermost side of the vehicle opposite to the driver's side, a front mirror of class VI is not mandatory. |
5.7. |
In the case of mirrors consisting of several reflecting surfaces which are either of a different curvature or make an angle with each other, at least one of the reflecting surfaces must provide the field of vision and have the dimensions (see point 2.2.2 of Annex II) specified for the class to which they belong. |
5.8. |
Obstructions 5.8.1. Interior rear-view mirror (Class I) The field of vision may be reduced by the presence of headrest and devices such as, in particular, sun visors, rear windscreen wipers, heating elements and stop lamp of category S3 or by components of bodywork such as window columns of rear split doors, provided that all these devices together do not obscure more than 15 per cent of the prescribed field of vision when projected onto a vertical plane perpendicular to the longitudinal median plane of the vehicle. The degree of obstruction shall be measured with the headrests adjusted to their lowest possible position and with the sun visors folded back. 5.8.2. Exterior mirrors (Classes II, III, IV, V and VI) In the fields of vision specified above, obstruction due to the bodywork and some of its components, such as other mirrors, door handles, outline marker lights, direction indicators and rear bumpers, as well as reflective-surface cleaning components, shall not be taken into account if they are responsible for a total obstruction of less than 10 % of the specified field of vision. |
5.9. |
Test procedure The field of vision shall be determined by placing powerful light sources at the ocular points and examining the light reflected on the vertical monitoring screen. Other equivalent methods may be used. |
Devices for indirect vision other than mirrors
6. |
A device for indirect vision shall give such performances that a critical object can be observed within the described field of vision, taking into account the critical perception. |
7. |
Obstruction of the driver's direct view caused by the installation of a device for indirect vision shall be restricted to a minimum. |
8. |
For the determination of the detection distance in case of camera-monitor devices for indirect vision, the procedure of the Appendix to this Annex shall be applied. |
9. |
Installation requirements for the monitor The viewing direction of the monitor shall roughly be the same direction as the one for the main mirror. |
10. |
Vehicles of category M2 and M3 and complete or completed vehicles of categories N2>7,5 t and N3 having a special bodywork for refuse collection may be equipped on the rear part of their bodywork with a device for indirect vision other than a mirror in order to ensure the following field of vision.
|
Appendix
Calculation of the detection distance
1. CAMERA MONITOR DEVICE FOR INDIRECT VISION
1.1. Resolution threshold of a camera
The resolution threshold of a camera is defined by the formula:
where:
ωc |
: |
resolution threshold of the camera (arc-min) |
βc |
: |
angle of vision of the camera (°) |
Nc |
: |
number of video lines of the camera |
The manufacturer shall supply the values for βc and Nc.
1.2. Determination of the critical viewing distance of the monitor
For a monitor having certain dimensions and properties, a distance to the monitor can be calculated within which the detection distance is dependent only on the performances of the camera. This critical viewing distance rm,c is defined by:
where:
rm,c |
: |
critical viewing distance (m) |
Hm |
: |
height of the monitor image (m) |
Nm |
: |
number of video lines of the monitor (-) |
ωeye |
: |
resolution threshold of the observer (minutes of arch) |
The number 60 is for conversion from minutes of arches to degrees.
The manufacturer shall supply the values for Hm and Nm.
ωeye = 1
1.3. Determination of the detection distance
1.3.1. |
Maximum detection distance within the critical viewing distance where, due to the installation, the distance eye-monitor is less than the critical viewing distance, the maximum attainable detection distance shall be defined by:
where:
ωc, βc and Nc according to item 1.1 D0= 0,8 m f = 8 |
1.3.2. |
Detection distance greater than the critical viewing distance. Where, due to the installation, the distance eye-monitor is more than the critical viewing distance, the maximum obtainable detection distance shall be defined:
where:
βc and Nc according to point 1.1 Nm and ωeye according to point 1.2 |
2. SECONDARY FUNCTIONAL REQUIREMENTS
Based on the installation conditions, a determination shall be made to discover whether the entire device can still satisfy the functional requirements listed in Annex II, especially the glare correction, the maximum and the minimum luminance of the monitor. It shall also be determined the degree to which the glare correction will be addressed and the angle at which sunlight can strike a monitor and these shall be compared to the corresponding measuring results from the system measurements.
This can be based on either a CAD-generated model, a determination of the angles of light for the device when mounted on the relevant vehicle, or by carrying out relevant measurements on the relevant vehicle as described in Annex II, part B, point 3.2.
ANNEX IV
CORRELATION TABLE PROVIDED FOR IN ARTICLE 6
Directive 71/127/EEC as amended |
This Directive |
— |
Article 1 |
— |
Article 2 |
Article 1 |
— |
Article 2 |
— |
Article 3 |
— |
Article 4 |
— |
Article 5 |
— |
Article 6 |
— |
Article 7 |
Article 3 |
Article 8 |
— |
— |
Article 4 |
Article 9 |
— |
Article 10 |
Article 5 |
— |
Article 6 |
— |
Article 7 |
Article 11 |
Article 8 |
Annex I |
Annex I |
Appendix 1 to Annex I |
Appendix 1 to Annex II |
— |
Appendix 1 to Annex I |
— |
Appendix 2 to Annex I |
— |
Appendix 3 to Annex I |
— |
Appendix 4 to Annex I |
— |
Appendix 5 to Annex I |
Appendix 2 to Annex I |
Appendix 6 to Annex I |
Annex II |
Annex II, A |
— |
Annex II, B |
Appendix 1 to Annex II |
Appendix 1 to Annex II |
— |
Appendix 2 to Annex II |
Appendix 2 to Annex II |
— |
Appendix 3 to Annex II |
Annex I and Appendix 5 to Annex I |
Annex III |
Appendix 2 to Annex I |
— |
Annex III |
Appendix to Annex III |
Appendix to Annex III |
— |
Appendix 4 to Annex I |
— |
Annex IV |
( 1 ) OJ C 126 E, 28.5.2002, p. 225.
( 2 ) OJ C 149, 21.6.2002, p. 5.
( 3 ) Opinion of the European Parliament of 9 April 2002 (OJ C 127 E, 29.5.2003, p. 25, Council common position of 8 April 2003 (OJ C 214 E, 9.9.2003, p. 7), position of the European Parliament of 1 July 2003 (not yet published in the Official Journal) and Council decision of 20 October 2003.
( 4 ) OJ L 68, 22.3.1971, p. 1. Directive as last amended by the 1994 Act of Accession.
( 5 ) OJ L 42, 23.2.1970, p. 1. Directive as last amended by Regulation (EC) No 807/2003 (OJ L 122, 16.5.2003, p. 36).
( 6 ) Directive 2001/85/EC of the European Parliament and of the Council of 20 November 2001 relating to special priorities for vehicles used for the carriage of passengers comprising more than eight seats in addition to the driver's seat (OJ L 42, 13.2.2002, p. 1).
( 7 ) A system for indirect vision is intended to detect relevant road users. The relevancy of a road user is defined by his or her position and (potential) speed. More or less in proportion with the speed of the pedestriancyclistmoped driver, the dimensions of these road users increase as well. For detection purposes a moped driver (D = 0,8) at 40 m distance would be equal to a pedestrian (D = 0,5) at a distance of 25 m. Considering the speeds, the moped driver would be selected as the criterion for the detection size; for that reason an object with a size of 0,8 m shall be used for determining the detection performance.
( 8 ) Delete where inapplicable.
( 13 ) Within the meaning of Annex IIA to Directive 70/156/EEC.
( 14 ) Delete where inapplicable.
( 17 ) Where appropriate, state whether the extension of the initial EC type-approval is the first, second, etc.
( 18 ) Delete where inapplicable.
( 21 ) Delete where inapplicable.
( 23 ) Definitions taken from CIE publication 50 (45), International Electronical Vocabulary, Group 45: Lighting.
(
28
) Abridged table. The values of(λ) = V(λ) are rounded off to four decimal places.