—

25 % or more but not more than 70 % arachidonic acid, or

—

12 % or more but not more than 65 % docosahexaenoic acid, and

—

standardized with high oleic sunflower oil (HOSO),

—

containing by weight 0,005  % or more, but not more than 0,1  % of antioxidants

—

92 % or more, but less than 98,5  % of aluminium oxide,

—

2 % (±1,5  %) of magnesium oxide,

—

1 % (±0,6  %) of yttrium oxide, and

—

either 3 % (±2,2  %) of lanthanum oxide or

—

2 % (±1,2  %) of lanthanum oxide and neodymium oxide,

—

an overall maximum length of 15,5  mm or more but not more than 29,4  mm, and

—

a pin length of 6,4  mm or more but not more than 12,6  mm

—

25 % or more but not more than 40 % of calcium C16-24 alkylbenzenesulphonates (CAS RN 70024-69-0),

—

30 % or more but not more than 65 % of mineral oils,

—

overbased magnesium (C20-C24) alkylbenzenesulphonates (CAS RN 231297-75-9) and

—

by weight more than 25 % but not more than 50 % of mineral oils,

—

having a total base number of more than 350, but not more than 450,

—

having thickness of both sides of 7 nm or more but not more than 80 nm, or thickness of both sides of 7 μm or more but not more than 80 μm, whether coated with an acrylic-based organic material or not,

—

with a surface tension of 36 Dyne/cm or more but not more than 39 Dyne/cm, or transparent 3 or 4 layers, second layer of PET, and other layers contain fluorine resin,

—

with a light transmittance of more than 70 %,

—

with a haze value of not more than 1,3  %,

—

with a total thickness of 10 μm or more but not more than 350 μm,

—

with a width of 800 mm or more but not more than 1 600  mm

—

a total thickness of 0,25  mm or more but not more than 0,40  mm,

—

a total weight of 109 g/m2 or more but not more than 114 g/m2

—

with a thickness of 2,20  mm or more but not more than 2,80  mm,

—

with a density of 0,95  g/cm3 or more,

—

lacquered or coated with melamine foil on both sides, and

—

with dimensions of 1 300  mm x 1 100  mm or less

—

electronic brake assistants,

—

hydraulic unit driven by brushless electric motor,

—

brake fluid reservoir,

—

an external diameter of 80 mm or more, but not more than 200 mm,

—

a supply voltage of 4V or more, but not more than 16 V,

—

an output at 20 oC of 200 W or more, but not more than 750 W,

—

a torque at 20 oC of 2,00 Nm or more, but not more than 7,00 Nm,

—

a rated speed at 20 oC of 600 rpm or more, but not more than 3 100 rpm,

—

with or without a pulley,

—

with or without an electronic power steering sensor/controller

—

an external diameter of 24,2  mm or more, but not more than 140 mm,

—

a rated speed of 3 300 rpm or more, but not more than 26 200 rpm,

—

a rated supply voltage of 3,6  V or more, but not more than 230 V,

—

an output power of more than 37,5  W, but not more than 2 400  W,

—

a free load current of not more than 20,1  A,

—

a maximum efficiency of 50 % or more

—

an external diameter of 27 mm or more but not more than 90 mm, including mounting flange,

—

a rated speed of not more than 25 000 rpm,

—

an output of 45 W or more but not more than 400 W, and

—

a supply voltage of 9 V or more but not more than 50 V,

—

whether or not a multiple-phase winding,

—

whether or not with a drive disc,

—

whether or not with a crankcase,

—

whether or not with a fan,

—

whether or not with a cap assembly,

—

whether or not with a sun gear,

—

whether or not with a speed and rotational direction encoder,

—

whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type,

—

whether or not with a mounting flange

—

whether or not arched,

—

whether or not with rounded corners or oblique sides,

—

whether or not colour marked

—

whether or not coated or passivated with a surface treatment,

—

whether or not consisting of segments bonded together and electrically insulated from one another

—

a length of 9 mm or more, but not more than 105 mm,

—

a width of 5 mm or more, but not more than 105 mm,

—

a thickness of 2 mm or more, but not more than 55 mm

—

a length of 15 mm or more but not more than 52 mm,

—

a width of 5 mm or more but not more than 42 mm,

—

whether or not coated or passivated with a surface treatment,

—

with a notch,

—

with an internal threaded bore on one side,

—

with a length of 97,5  mm or more, but not more than 225 mm,

—

with a diameter of 19 mm or more, but not more than 25 mm,

—

whether or not coated or passivated with a surface treatment

—

with an external diameter of not more than 45 mm,

—

with a height of not more than 45 mm,

—

whether or not coated or passivated with a surface treatment,

—

a rectangular or a trapezoidal cross-section,

—

a length of not more than 140 mm,

—

a width of not more than 90 mm and

—

a thickness of not more than 55 mm,

—

a length of not more than 75 mm,

—

a width of not more than 40 mm,

—

a thickness of not more than 7 mm and

—

a radius of curvature of more than 86 mm but not more than 241 mm,

—

layers of nickel and copper

—

a diameter of not more than 90 mm,

—

whether or not a hole in the centre

—

a diameter of not more than 90 mm,

—

whether or not a hole in the centre,

—

layers of copper, nickel and/or zinc,

—

a length of 16,8  mm or more, but not more than 110,2  mm,

—

a width of 14,8  mm or more, but not more than 75,2  mm,

—

a thickness of 4,8  mm or more, but not more than 13,2  mm,

—

a diameter of not more than 120 mm,

—

a hole in the centre,

—

a length of 26,85  mm or more but not more than 32,15  mm,

—

a width of 7,6  mm or more but not more than 9,55  mm,

—

a thickness of 5,3  mm or more but not more than 5,8  mm, and

—

a weight of 6,1  g or more but not more than 8,3  g,

—

whether or not coated or passivated with a surface treatment,

—

whether or not with rounded corners,

—

a length of 9 mm or more but not more than 101 mm,

—

a width of 9 mm or more but not more than 101 mm,

—

a thickness of 1,85  mm or more but not more than 15,15  mm,

—

6 modules with 90 cells or more but not more than 192 cells,

—

a nominal voltage of 280 V or more but not more than 400 V,

—

a nominal capacity of 9,7 Ah or more but not more than 120 Ah,

—

a charging voltage of 110 V or more but not more than 495 V, and

—

a length of not more than 1 723  mm,

—

a width of not more than 1 162,23  mm,

—

a height of not more than 395 mm,

—

a length of 50 mm or more, but not more than 120 mm,

—

a width of 35 mm or more, but not more than 80 mm,

—

a height of 15 mm or more, but not more than 45 mm,

—

a weight of 0,040  kg or more but not more than 0,085  kg; and

—

a capacity of not more than 2 200  mAh

—

a length of 298 mm or more, but not more than 500 mm,

—

a width of 33,5  mm or more, but not more than 209 mm,

—

a height of 75 mm or more, but not more than 228 mm,

—

a weight of 3,6  kg or more, but not more than 17 kg,

—

a power of 458 Wh or more, but not more than 3 510 Wh, and

—

a voltage of less than 45 V or more than 70 V

—

a length of 570 mm or more, but not more than 610 mm,

—

a width of 210 mm or more, but not more than 240 mm,

—

a height of 100 mm or more, but not more than 120 mm,

—

a weight of 28 kg or more, but not more than 35 kg, and

—

a capacity of not more than 2 500 Ah and a nominal energy of less than 8,4  kW,

—

whether or not including parts made of aluminum and aluminum alloy,

—

with or without sealing elements or other elements made of polymer material,

—

with or without a “current interrupt device” and an “evacuation valve”

—

with or without plastic sockets

—

with an outer diameter of 17 mm or more, but not more than 18 mm,

—

length not greater than 450 mm,

—

width not greater than 200 mm, and

—

hight not greater than 150 mm,

—

45 % or more, but not more than 90 % silver (CAS RN 7440-22-4) and

—

59 % or more, but not more than 92 % of the total solids (including silver)

—

72 % or more but not more than 82 % aluminium (CAS RN 7429-90-5)

—

with a viscosity of 10 or more, but not more than 100 Pa.s (Brookfield RVT, 14 Spindle, 20 rpm, 25 oC±0,5  oC)

—

with an aluminium particle size of not more than 25 μm

—

49 % or more but not more than 51 % of ethylene carbonate (CAS RN 96-49-1), and

—

49 % or more but not more than 51 % of 1,3-propanesultone (CAS RN 1120-71-4)

—

with a thickness of 50 μm or more,

—

with a width of 6,30  mm or more but not more than 740 mm,

—

an elongation at break of not more than 200 %, and

—

coated on one side with a pressure sensitive silicone adhesive with a thickness of not more than 50 μm

—

with a gloss of more than 25 degrees according to ASTM D 2457,

—

whether or not covered on one side with a protective film of polyethylene terephthalate and on the other side with a micro-structured pressure sensitive acrylic adhesive and a release liner

—

a density of 20 kg/m3 or more, but not more than 40 kg/m3,

—

a tensile strength of not less than 170 kPa,

—

water absorption coefficient of not greater than 1 %,

—

a length of 5 mm or more but not more than 300 mm,

—

a height of 10 mm or more but not more than 400 mm,

—

a depth of 5 mm or more but not more than 250 mm

—

a steel bracket with at least one mounting hole and

—

silent block,

—

covered with diamond grains of 5 μm or more but not more than 55 μm,

—

with a wire diameter of 45 μm or more, but not more than 350 μm

—

a breaking strength of 11 N or more but not more than 170 N

—

a length of 155 mm or more, but not more than 158 mm,

—

a height of 115 mm or more, but not more than 120 mm,

—

a blind spot sensor with a blind spot motion detection light module, with an edge luminescence greater than or equal to 5 000 cd/m2 and a central luminescence greater than or equal to 7 000 cd/m2,

—

a heater foil, with a resistance of 1,1  kΩ or more, but not more than 1,35 kΩ,

—

with a length of 140 mm or more but not more than 215 mm,

—

with a height of 104 mm or more but not more than 138 mm,

—

with curvature radius of 0 mm or more but not more than 1 330  mm,

—

with a reflectance of more than 40 %,

—

a dilution steam generator system which produces steam from pretreated quench water for use as dilution steam in steam cracking furnaces,

—

a condensate system that collects, filters and deaerates steam condensates, which are subsequently recycled as boiler feed water and further distributed within the cracker unit, and

—

a flare system that collects, separates and vaporizes non-recyclable hydrocarbon containing releases from different equipment in a steam cracker, and transfers those towards flares

—

2 mounting holes with a diameter of 31 mm,

—

a choke bore diameter of 18 mm or more, but not more than 19,05  mm

—

a direct current operating voltage of more than 10 V but not more than 14 V, or

—

an alternating current operating voltage of more than 185 V, but not more than 254 V,

—

an operating temperature of - 40 oC or higher, but not higher than 70 oC,

—

with an operating voltage of 9 VDC or more but not more than 16 VDC,

—

with a centrifugal electric fan,

—

with a connector,

—

with a plastic case,

—

with or without a control unit for the fan electric motor,

—

quench water circulation loops, which contain a heat exchanger and circulation pumps to cool and recirculate quench water,

—

a water purification system, which removes hydrocarbon contaminants from quench water which is then re-used for dilution steam production (outside the module),

—

a pyrolysis oil purification system, which separates pyrolysis gasoline, heavy oil and coke fractions from the hydrocarbon contaminants that have been removed from the quench water,

—

an ethane feedstock start-up vaporizer and superheater, which vaporizes and heats ethane feedstock before sending the ethane to the cracking furnaces (outside the module),

—

a propane feedstock preparation system, which filters, vaporizes and superheats propane feedstock, before sending the propane to cracking furnaces (outside the module), and

—

a chemical grade propylene preparation system, which filters and dries chemical grade propylene before sending it to the deethanizer (outside the module)

—

an open loop ethylene refrigeration system, which is to be integrated with an external ethylene refrigerant compressor,

—

pumps and a heat exchanger to deliver ethylene to an external pipeline, and

—

a closed loop propylene refrigeration system, which is to be integrated with an external propylene refrigerant compressor

—

coolers,

—

vapor-liquid separation drums, and

—

pumps needed to condense and remove water and heavier hydrocarbons and to avoid undesirable formation of polymer by-products,

—

caustic water circulation pumps to support an external caustic wash tower in removing acid gasses (carbon dioxide and hydrogen sulphide) from the cracked gas,

—

a spent caustic pre-treatment system, containing separation drums, pumps and mixers,

—

a heat exchanger for the pre-cooling of cracked gas, and

—

a separation drum for the removal of water from cracker gas

—

in the form of hedge trimmer attachment,

—

with a knife length of 60 cm and teeth opening of 30 mm,

—

with angle adjustment of the blade,

—

with integrated single stage gearbox,

—

with a magnesium cast body,

—

various distillation columns (depropanizer, debutanizer and degreenoiler) and their associated heat exchangers, pumps and drums,

—

a chilling train containing heat exchangers and a drum which condenses C2 in a gas stream,

—

a system to separate hydrogen and methane from cracked gas containing heat exchangers, drums, turbines, compressors and a hydrogen purification unit (pressure swing adsorption unit),

—

associated equipment of a C3 splitter distillation column, containing heat exchanger, pumps and drums, and

—

a vinyl acetylene hydrogenation system, containing hydrogenation reactors, filters, mixer, drum, condenser, heat exchangers

—

a system for filtering and cooling of dried cracked gas,

—

a deethanizer distillation column and associated equipment for C2-/C3+ separation,

—

an acetylene hydrogenation system to remove acetylene within a C2 stream,

—

a fuel gas drum that stores fuel gas for cracker furnaces, and

—

a system to regenerate dryers in a cracker installation

—

made of lightweight alloys and steel,

—

built on straight or helical bevel gears,

—

with an angle between the shafts of 30 degrees or more but not more than 90 degrees

—

with a gear 1:1,3 ratio or more but not more than 1:1,46 ,

—

made of lightweight alloys and steel,

—

built on straight bevel gears,

—

with an angle between the shafts of 24 degrees or more but not more than 35 degrees,

—

with a rated power of 240 W or more, but not more than 260 W,

—

with a voltage of 36 V or higher, but not higher than 52 V

—

with a torque of 20 Nm or more, but not more than 140 Nm,

—

with a housing made of aluminum, aluminum alloy or plastic,

—

with or without a built-in controller,

—

with a communication function in the LIN or UART interface,

—

weighing 1,5  kg or more, but not more than 5,0  kg,

—

adapted for mounting in a bicycle frame

—

with a rated power of 240 W or more, but not more than 260 W,

—

with voltage of 36 V or higher, but not higher than 52 V,

—

with torque of 30 Nm or more, but not more than 50 Nm,

—

with communication function UART or CAN interface,

—

with internal planetary gearbox with fixed or variable ratio,

—

made by CNC machined casting,

—

with housing made of aluminum,

—

weighing 2,3  kg or more, but not more than 4,4  kg,

—

adapted for mounting in the front or rear bicycle wheel (2)

—

of EN AC-47100-F aluminum,

—

with a sealing cap of stainless steel,

—

shot-blasted and machined,

—

leakproof to the degree of 1 ml per minute or less under 2,75 bar pressure,

—

with a hardness of 70 HBW or more (2,5 /62,5 , according to ISO 6506),

—

with a tensile strength of 240 N/mm2 or more,

—

with a height of 50 mm or more, but not more than 55 mm,

—

with a diameter of 109 mm or more, but not more than 112 mm,

—

with a weight of 3,9  kg or more but not more than 4,2  kg

—

of EN AC-47100 aluminum,

—

shot-blasted and machined,

—

leakproof to the degree of 3 ml per minute or less under 2,75 bar pressure,

—

with a hardness of 70 HBW or more (2,5 /62,5 , according to ISO 6506)

—

with a tensile strength of 240 N/mm2 or more,

—

with a height of 225 mm or more, but not more than 280 mm,

—

with a diameter of 300 mm or more, but not more than 310 mm,

—

with a weight of 3,8  kg or more, but not more than 4,9  kg

—

of EN AC-47100 aluminum,

—

with overmolded bearing sleeves of martensitic stainless steel and assembled sealing caps of stainless steel,

—

shot-blasted and machined,

—

a rotor chamber, leakproof to the degree of 3 ml per minute or less under 2,75 bar pressure,

—

with a hardness of 70 HBW or more (2,5 /62,5 , according to ISO 6506)

—

with a tensile strength of 240 N/mm2 or more,

—

with a height of 245 mm or more, but not more than 360 mm,

—

with a width of 360 mm or more, but not more than 525 mm,

—

with a length of 345 mm or more, but not more than 450 mm,

—

with a weight of 6,4  kg or more, but not more than 8,3  kg

—

transmitting torque from the motor shaft to the cutting device pulley,

—

containing field coil, rotor, hub and armature,

—

with an operating voltage of 12 V

—

a current of 3,93  A current or more but not more than 6,86  A,

—

a resistance of 1,84  ohm or more but not more than 3,05  ohm (operating at 20 oC),

—

a static torque of 108 Nm or more but not more than 305 Nm

—

a length of 820 mm or more, but not more than 882 mm,

—

a width of 390 mm or more, but not more than 655 mm,

—

a height of 110 mm or more, but not more than 137 mm,

—

a weight of 60 kg or more, but not more than 165 kg, and

—

a power of 11 300 Wh or more, but not more than 29 360  Wh

—

a length of 190 mm or more but not more than 380 mm,

—

a width of 90 mm or more but not more than 150 mm,

—

a height of 4 mm or more but not more than 15 mm,

—

a weight of 0,1  kg or more but not more than 1,2  kg,

—

a nominal voltage of 3,0 VDC or more but not more than 4,0 VDC,

—

a nominal capacity of not more than 90 Ah,

—

multiple connected lithium-ion accumulator cells,

—

charging and monitoring electronics,

—

a power of 74 Wh or more, but not more than 75 Wh,

—

in a plastic housing with electrical connection contacts and LCD display,

—

made with plastics and non-ferrous metals,

—

with the electric components cast in epoxy resin,

—

to generate the ignition energy and to electronically control the ignition timing,

—

to connect spark plug and circuit breaker,

—

a voltage of 11 V or more, but not more than 15 V,

—

a circular shape,

—

2 terminals,

—

an outer diameter of the housing of 42,3  mm,

—

a diode voltage of 42 V or more, but not more than 48 V and

—

a current of 55 mA or more, but not more than 65 mA

—

an input waterproof connector,

—

four or more output connectors,

—

two or more plastic clips for attachment