EUR-Lex Access to European Union law
This document is an excerpt from the EUR-Lex website
Document 02019D1616-20230621
Commission Implementing Decision (EU) 2019/1616 of 27 September 2019 on the harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU of the European Parliament and of the Council
Consolidated text: Commission Implementing Decision (EU) 2019/1616 of 27 September 2019 on the harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU of the European Parliament and of the Council
Commission Implementing Decision (EU) 2019/1616 of 27 September 2019 on the harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU of the European Parliament and of the Council
ELI: http://data.europa.eu/eli/dec_impl/2019/1616/2023-06-21
02019D1616 — EN — 21.06.2023 — 006.001
This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document
COMMISSION IMPLEMENTING DECISION (EU) 2019/1616 of 27 September 2019 (OJ L 250 30.9.2019, p. 95) |
Amended by:
|
|
Official Journal |
||
No |
page |
date |
||
COMMISSION IMPLEMENTING DECISION (EU) 2020/542 of 16 April 2020 |
L 121 |
4 |
20.4.2020 |
|
COMMISSION IMPLEMENTING DECISION (EU) 2021/157 of 9 February 2021 |
L 46 |
40 |
10.2.2021 |
|
COMMISSION IMPLEMENTING DECISION (EU) 2021/1801 of 11 October 2021 |
L 361 |
53 |
12.10.2021 |
|
COMMISSION IMPLEMENTING DECISION (EU) 2021/2272 of 20 December 2021 |
L 457 |
10 |
21.12.2021 |
|
COMMISSION IMPLEMENTING DECISION (EU) 2022/1844 of 28 September 2022 |
L 254 |
58 |
3.10.2022 |
COMMISSION IMPLEMENTING DECISION (EU) 2019/1616
of 27 September 2019
on the harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU of the European Parliament and of the Council
Article 1
The references of harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU, listed in Annex I to this Decision, are hereby published in the Official Journal of the European Union.
Article 2
The references of harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU, listed in Annex II to this Decision, are hereby withdrawn from the Official Journal of the European Union as from the dates set out in that Annex.
Article 3
This Decision shall enter into force on the day of its publication in the Official Journal of the European Union.
ANNEX I
No |
Reference of the standard |
1. |
EN 1562:2019 Founding — Malleable cast irons |
2. |
EN 1563:2018 Founding — Spheroidal graphite cast irons |
3. |
EN ISO 4126-2:2019 Safety devices for protection against excessive pressure — Part 2: Bursting disc safety devices (ISO 4126-2:2018) |
4. |
EN 12516-1:2014+A1:2018 Industrial valves — Shell design strength — Part 1: Tabulation method for steel valve shells |
5. |
EN 12516-4:2014+A1:2018 Industrial valves — Shell design strength — Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
6. |
EN 13136:2013+A1:2018 Refrigerating systems and heat pumps — Pressure relief devices and their associated piping — Methods for calculation |
▼M4 ————— |
|
7a. |
EN 13445-2:2021 Unfired pressure vessels – Part 2: Materials |
▼M4 ————— |
|
8a. |
EN 13445-3:2021 Unfired pressure vessels – Part 3: Design |
▼M4 ————— |
|
9a. |
EN 13445-5:2021 Unfired pressure vessels – Part 5: Inspection and testing |
▼M4 ————— |
|
10a. |
EN 13445-6:2021 Unfired pressure vessels – Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron |
11. |
EN 13480-2:2017 Metallic industrial piping - Part 2: Materials EN 13480-2:2017/A1:2018 EN 13480-2:2017/A2:2018 EN 13480-2:2017/A3:2018 EN 13480-2:2017/A7:2020 |
11a. |
EN 13480-2:2017 Metallic industrial piping - Part 2: Materials EN 13480-2:2017/A3:2018 EN 13480-2:2017/A1:2018 EN 13480-2:2017/A2:2018 EN 13480-2:2017/A7:2020 EN 13480-2:2017/A8:2021 |
12. |
EN 13480-5:2017 Metallic industrial piping — Part 5: Inspection and testing EN 13480-5:2017/A1:2019 |
12a. |
EN 13480-5:2017 Metallic industrial piping - Part 5: Inspection and testing EN 13480-5:2017/A1:2019 EN 13480-5:2017/A2:2021 |
13. |
EN ISO 15494:2018 Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for components and the system (ISO 15494:2015) |
14. |
EN ISO 21028-2:2018 Cryogenic vessels — Toughness requirements for materials at cryogenic temperature — Part 2: Temperatures between – 80 degrees C and – 20 degrees C (ISO 21028-2:2018) |
15. |
EN ISO 4126-1:2013 Safety devices for protection against excessive pressure – Part 1: Safety valves (ISO 4126-1:2013) EN ISO 4126-1:2013/A2:2019 |
16. |
EN 10217-1:2019 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties |
17. |
EN 10217-2:2019 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties |
18. |
EN 10217-3:2019 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 3: Electric welded and submerged arc welded alloy fine grain steel tubes with specified room, elevated and low temperature properties |
19. |
EN 10217-4:2019 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 4: Electric welded non-alloy steel tubes with specified low temperature properties |
20. |
EN 10217-5:2019 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties |
21. |
EN 10217-6:2019 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties |
22. |
EN 13480-1:2017 Metallic industrial piping – Part 1: General EN 13480-1:2017/A1:2019 |
23. |
EN 13480-6:2017 Metallic industrial piping – Part 6: Additional requirements for buried piping EN 13480-6:2017/A1:2019 |
24. |
EN ISO 4126-3:2020 Safety devices for protection against excessive pressure - Part 3: Safety valves and bursting disc safety devices in combination (ISO 4126-3:2020) |
25. |
EN 12542:2020 LPG equipment and accessories - Static welded steel cylindrical pressure vessels, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m3 - Design and manufacture |
26. |
EN 12735-1:2020 Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems |
27. |
EN 12953-5:2020 Shell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler |
28. |
EN 13175:2019+A1:2020 LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings |
29. |
EN 13480-3:2017 Metallic industrial piping – Part 3: Design and calculation EN 13480-3:2017/A2:2020 EN 13480-3:2017/A3:2020 EN 13480-3:2017/A1:2021 |
29a. |
EN 13480-3:2017 Metallic industrial piping - Part 3: Design and calculation EN 13480-3:2017/A3:2020 EN 13480-3:2017/A1:2021 EN 13480-3:2017/A2:2020 EN 13480-3:2017/A4:2021 |
30. |
EN 14276-1:2020 Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
31. |
EN 14276-2:2020 Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements |
32. |
EN ISO 15620:2019 Welding - Friction welding of metallic materials (ISO 15620:2019) |
33. |
EN ISO 16135:2006 Industrial valves - Ball valves of thermoplastics materials (ISO 16135:2006) EN ISO 16135:2006/A1:2019 |
34. |
EN ISO 16136:2006 Industrial valves - Butterfly valves of thermoplastics materials (ISO 16136:2006) EN ISO 16136:2006/A1:2019 |
35. |
EN ISO 16137:2006 Industrial valves - Check valves of thermoplastics materials (ISO 16137:2006) EN ISO 16137:2006/A1:2019 |
36. |
EN ISO 16138:2006 Industrial valves - Diaphragm valves of thermoplastics materials (ISO 16138:2006) EN ISO 16138:2006/A1:2019 |
37. |
EN ISO 16139:2006 Industrial valves - Gate valves of thermoplastics materials (ISO 16139:2006) EN ISO 16139:2006/A1:2019 |
38. |
EN 16767:2020 Industrial valves - Metallic check valves |
39. |
EN ISO 21787:2006 Industrial valves - Globe valves of thermoplastics materials (ISO 21787:2006) EN ISO 21787:2006/A1:2019 |
40. |
EN 1515-4:2021 Flanges and their joints – Bolting – Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU |
41. |
EN 14222:2021 Stainless steel steam boilers |
42. |
EN 10216-5:2021 Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 5: Stainless steel tubes |
43. |
EN 10217-7:2021 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 7: Stainless steel tubes |
44. |
EN 10222-2:2017+A1:2021 Steel forgings for pressure purposes – Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
45. |
EN 10222-4:2017+A1:2021 Steel forgings for pressure purposes – Part 4: Weldable fine grain steels with high proof strength |
46. |
EN 13445-1:2021 Unfired pressure vessels – Part 1: General |
47. |
EN 13445-4:2021 Unfired pressure vessels – Part 4: Fabrication |
48. |
EN 13445-8:2021 Unfired pressure vessels – Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys |
49. |
EN 13445-10:2021 Unfired pressure vessels – Part 10: Additional requirements for pressure vessels of nickel and nickel alloys |
50. |
EN 17278:2021 Natural gas vehicles – Vehicle fuelling appliances |
51. |
EN 3-8:2021 Portable fire extinguishers - Part 8: Requirements for the construction, pressure resistance and mechanical tests for extinguishers with a maximum allowable pressure equal to or lower than 30 bar, which comply with the requirements of EN 3-7 |
52. |
EN ISO 9712:2022 Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2021) |
53. |
EN 10253-2:2021 Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
54. |
EN 12516-2:2014+A1:2021 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
55. |
EN 12952-2:2021 Water-tube boilers and auxiliary installations - Part 2: Materials for pressure parts of boilers and accessories |
56. |
EN 12952-5:2021 Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler |
57. |
EN 12952-6:2021 Water-tube boilers and auxiliary installations - Part 6: Inspection during construction, documentation and marking of pressure parts of the boiler |
58. |
EN 12952-10:2021 Water-tube boilers and auxiliary installations - Part 10: Requirements for safety devices against excessive pressure |
59. |
EN 13121-1:2021 GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance criteria |
60. |
EN 14917:2021 Metal bellows expansion joints for pressure applications |
61. |
EN ISO 21922:2021 Refrigerating systems and heat pumps - Valves - Requirements, testing and marking (ISO 21922:2021) |
ANNEX II
No |
Reference of the standard |
Date of withdrawal |
1. |
EN 13445-2:2014 Unfired pressure vessels — Part 2: Materials EN 13445-2:2014/A1:2016 EN 13445-2:2014/A2:2018 |
30 September 2019 |
2. |
EN 13445-3:2014 Unfired pressure vessels — Part 3: Design EN 13445-3:2014/A1:2015 EN 13445-3:2014/A2:2016 EN 13445-3:2014/A3:2017 EN 13445-3:2014/A4:2018 |
30 September 2019 |
3. |
EN 13445-5:2014 Unfired pressure vessels — Part 5: Inspection and testing |
30 September 2019 |
4. |
EN 13445-6:2014 Unfired pressure vessels — Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron |
30 September 2019 |
5. |
EN 13480-2:2017 Metallic industrial piping — Part 2: Materials |
30 September 2019 |
6. |
EN 13480-5:2017 Metallic industrial piping — Part 5: Inspection and testing |
30 September 2019 |
7. |
EN 1252-2:2001 Cryogenic vessels — Materials — Part 2: Toughness requirements for temperatures between – 80 °C and – 20 °C |
30 March 2020 |
8. |
EN 1562:2012 Founding — Malleable cast irons |
30 March 2020 |
9. |
EN 1563:2011 Founding — Spheroidal graphite cast irons |
30 March 2020 |
10. |
EN 12516-1:2014 Industrial valves — Shell design strength — Part 1: Tabulation method for steel valve shells |
30 March 2020 |
11. |
EN 12516-4:2014 Industrial valves — Shell design strength — Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
30 March 2020 |
12. |
EN 13136:2013 Refrigerating systems and heat pumps — Pressure relief devices and their associated piping — Methods for calculation |
30 March 2020 |
13. |
EN 10217-1:2002 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties EN 10217-1:2002/A1:2005 |
20 April 2021 |
14. |
EN 10217-2:2002 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties EN 10217-2:2002/A1:2005 |
20 April 2021 |
15. |
EN 10217-3:2002 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 3: Alloy fine grain steel tubes EN 10217-3:2002/A1:2005 |
20 April 2021 |
16. |
EN 10217-4:2002 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 4: Electric welded non-alloy steel tubes with specified low temperature properties EN 10217-4:2002/A1:2005 |
20 April 2021 |
17. |
EN 10217-5:2002 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties EN 10217-5:2002/A1:2005 |
20 April 2021 |
18. |
EN 10217-6:2002 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties EN 10217-6:2002/A1:2005 |
20 April 2021 |
19. |
EN 13480-1:2017 Metallic industrial piping – Part 1: General |
20 April 2020 |
20. |
EN 13480-6:2017 Metallic industrial piping – Part 6: Additional requirements for buried piping |
20 April 2020 |
21. |
EN ISO 4126-1:2013 Safety devices for protection against excessive pressure – Part 1: Safety valves (ISO 4126-1:2013) |
20 April 2020 |
22. |
EN 12542:2010 LPG equipment and accessories - Static welded steel cylindrical tanks, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m3 - Design and manufacture |
10 August 2022 |
23. |
EN 12735-1:2016 Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems |
10 August 2022 |
24. |
EN 12953-5:2002 Shell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler |
10 August 2022 |
25. |
EN 13175:2014 LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings |
10 August 2022 |
26. |
EN 13480-3:2017 Metallic industrial piping - Part 3: Design and calculation |
10 August 2022 |
27. |
EN 14276-1:2006+A1:2011 Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
10 August 2022 |
28. |
EN 14276-2:2007+A1:2011 Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements |
10 August 2022 |
29. |
EN 16767:2016 Industrial valves - Steel and cast iron check valves |
10 August 2022 |
30. |
EN ISO 15620:2000 Welding - Friction welding of metallic materials (ISO 15620:2000) |
10 August 2022 |
31. |
EN ISO 16135:2006 Industrial valves - Ball valves of thermoplastics materials (ISO 16135:2006) |
10 August 2022 |
32. |
EN ISO 16136:2006 Industrial valves - Butterfly valves of thermoplastics materials (ISO 16136:2006) |
10 August 2022 |
33. |
EN ISO 16137:2006 Industrial valves - Check valves of thermoplastics materials (ISO 16137:2006) |
10 August 2022 |
34. |
EN ISO 16138:2006 Industrial valves - Diaphragm valves of thermoplastics materials (ISO 16138:2006) |
10 August 2022 |
35. |
EN ISO 16139:2006 Industrial valves - Gate valves of thermoplastics materials (ISO 16139:2006) |
10 August 2022 |
36. |
EN ISO 21787:2006 Industrial valves - Globe valves of thermoplastics materials (ISO 21787:2006) |
10 August 2022 |
37. |
EN ISO 4126-3:2006 Safety devices for protection against excessive pressure - Part 3: Safety valves and bursting disc safety devices in combination (ISO 4126-3:2006) |
10 August 2022 |
38. |
EN 1515-4:2009 Flanges and their joints – Bolting – Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
12 April 2023 |
39. |
EN 14222:2003 Stainless steel shell boilers |
12 April 2023 |
40. |
EN 10216-5:2013 Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 5: Stainless steel tubes |
21 June 2023 |
41. |
EN 10217-7:2014 Welded steel tubes for pressure purposes – Technical delivery conditions – Part 7: Stainless steel tubes |
21 June 2023 |
42. |
EN 10222-2:2017 Steel forgings for pressure purposes – Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
21 June 2023 |
43. |
EN 10222-4:2017 Steel forgings for pressure purposes – Part 4: Weldable fine grain steels with high proof strength |
21 June 2023 |
44. |
EN 13445-1:2014 Unfired pressure vessels – Part 1: General EN 13445-1:2014/A1:2014 |
21 June 2023 |
45. |
EN 13445-4:2014 Unfired pressure vessels – Part 4: Fabrication |
21 June 2023 |
46. |
EN 13445-8:2014 Unfired pressure vessels – Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys EN 13445-8:2014/A1:2014 |
21 June 2023 |
47. |
EN 10253-2:2007 Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
3.4.2024 |
48. |
EN 12284:2003 Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
3.4.2024 |
49. |
EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
3.4.2024 |
50. |
EN 12952-10:2002 Water-tube boilers and auxiliary installations - Part 10: Requirements for safeguards against excessive pressure |
3.4.2024 |
51. |
EN 12952-2:2011 Water-tube boilers and auxiliary installations - Part 2: Materials for pressure parts of boilers and accessories |
3.4.2024 |
52. |
EN 12952-5:2011 Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler |
3.4.2024 |
53. |
EN 12952-6:2011 Water-tube boilers and auxiliary installations - Part 6: Inspection during construction; documentation and marking of pressure parts of the boiler |
3.4.2024 |
54. |
EN 13121-1:2003 GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions |
3.4.2024 |
55. |
EN 14917:2009+A1:2012 Metal bellows expansion joints for pressure applications |
3.4.2024 |
56. |
EN 3-8:2006 Portable fire extinguishers - Part 8: Additional requirements to EN 3-7 for the construction, resistance to pressure and mechanical tests for extinguishers with a maximum allowable pressure equal to or lower than 30 bar EN 3-8:2006/AC:2007 |
3.4.2024 |
57. |
EN ISO 9712:2012 Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
3.4.2024 |