EUR-Lex Access to European Union law
This document is an excerpt from the EUR-Lex website
Document 31997D0464
97/464/EC: Commission Decision of 27 June 1997 on the procedure for attesting the conformity of construction products pursuant to Article 20 (2) of Council Directive 89/106/EEC as regards waste water engineering products (Text with EEA relevance)
97/464/EC: Commission Decision of 27 June 1997 on the procedure for attesting the conformity of construction products pursuant to Article 20 (2) of Council Directive 89/106/EEC as regards waste water engineering products (Text with EEA relevance)
97/464/EC: Commission Decision of 27 June 1997 on the procedure for attesting the conformity of construction products pursuant to Article 20 (2) of Council Directive 89/106/EEC as regards waste water engineering products (Text with EEA relevance)
OJ L 198, 25.7.1997, p. 33–36
(ES, DA, DE, EL, EN, FR, IT, NL, PT, FI, SV)
Special edition in Czech: Chapter 13 Volume 019 P. 158 - 161
Special edition in Estonian: Chapter 13 Volume 019 P. 158 - 161
Special edition in Latvian: Chapter 13 Volume 019 P. 158 - 161
Special edition in Lithuanian: Chapter 13 Volume 019 P. 158 - 161
Special edition in Hungarian Chapter 13 Volume 019 P. 158 - 161
Special edition in Maltese: Chapter 13 Volume 019 P. 158 - 161
Special edition in Polish: Chapter 13 Volume 019 P. 158 - 161
Special edition in Slovak: Chapter 13 Volume 019 P. 158 - 161
Special edition in Slovene: Chapter 13 Volume 019 P. 158 - 161
Special edition in Bulgarian: Chapter 13 Volume 021 P. 233 - 237
Special edition in Romanian: Chapter 13 Volume 021 P. 233 - 237
Special edition in Croatian: Chapter 13 Volume 053 P. 53 - 56
No longer in force, Date of end of validity: 18/11/2015; Repealed and replaced by 32015D1959
25.7.1997 |
EN |
Official Journal of the European Union |
L 198/33 |
COMMISSION DECISION
of 27 June 1997
on the procedure for attesting the conformity of construction products pursuant to Article 20 (2) of Council Directive 89/106/EEC as regards waste water engineering products
(Text with EEA relevance)
(97/464/EC)
THE COMMISSION OF THE EUROPEAN COMMUNITIES,
Having regard to the Treaty establishing the European Community,
Having regard to Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (1), as amended by Directive 93/68/EEC (2), and in particular Article 13 (4) thereof,
Whereas the Commission is required to select, as between the two procedures in accordance with Article 13 (3) of Directive 89/106/EEC for attesting the conformity of a product, the ‘least onerous possible procedure consistent with safety’; whereas this means that it is necessary to decide whether, for a given product or family of products, the existence of a factory production control system under the responsibility of the manufacturer is a necessary and sufficient condition for an attestation of conformity, or whether, for reasons related to compliance with the criteria mentioned in Article 13 (4), the intervention of an approved certification body is required for that purpose;
Whereas Article 13 (4) requires that the procedure thus determined must be indicated in the mandates and in the technical specifications; whereas, therefore, it is desirable to define the concept of products or family of products as used in the mandates and in the technical specifications;
Whereas the two procedures provided for in Article 13 (3) are described in detail in Annex III to Directive 89/106/EEC; whereas it is necessary therefore to specify clearly the methods by which the two procedures must be implemented, by reference to Annex III, for each product or family of products, since Annex III gives preference to certain systems;
Whereas the procedure referred to in point (a) of Article 13 (3) corresponds to the systems set out in the first possibility, without continuous surveillance, and the second and third possibilities of point (ii) of Section 2 of Annex III, and the procedure referred to in point (b) of Article 13 (3) corresponds to the systems set out in point (i) of Section 2 of Annex III, and in the first possibility, with continuous surveillance, of point (ii) of Section 2 of Annex III;
Whereas the measures provided for in this Decision are in accordance with the opinion of the Standing Committee on Construction,
HAS ADOPTED THIS DECISION:
Article 1
The products set out in Annex I shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in assessment and surveillance of the production control or of the product itself.
Article 2
The procedure for attesting conformity as set out in Annex II shall be indicated in mandates for harmonized standards.
Article 3
This Decision is addressed to the Member States.
Done at Brussels, 27 June 1997.
For the Commission
Martin BANGEMANN
Member of the Commission
(1) OJ No L 40, 11. 2. 1989, p. 12.
(2) OJ No L 220, 30. 8. 1993, p. 1.
ANNEX I
Waste water engineering products inside buildings
Back-flow devices: air admittance valve ventilating pipework.
Kits for waste water pumping station and effluent lifting plants.
Waste water engineering products outside buildings
Kits and elements for waste water treatment plants and on-site treatment equipment.
Septic tanks.
Prefabricated drainage channel.
Manholes and inspection chambers.
Covers, step irons, ladders and handrail for manholes and inspection chambers, gully tops.
Separators.
ANNEX II
PRODUCT FAMILY
WASTE WATER ENGINEERING PRODUCTS INSIDE BUILDINGS (1/2)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
Product |
Intended use |
Level or class |
Attestation of conformity system |
Back-flow devices: air admittance valve ventilating pipework |
For use inside buildings |
|
4 (1) |
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
PRODUCT FAMILY
WASTE WATER ENGINEERING PRODUCTS INSIDE BUILDINGS (2/2)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
Product(s) |
Intended use(s) |
Level(s) or class(es) |
Attestation of conformity system(s) |
Kits for waste water pumping station and effluent lifting plants |
For use inside building |
|
3 (2) |
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
PRODUCT FAMILY
WASTE WATER ENGINEERING PRODUCTS OUTSIDE BUILDINGS (1/3)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
Product(s) |
Intended use(s) |
Level(s) or class(es) |
Attestation of conformity system(s) |
||
Kits and elements for waste water treatment plants and on-site treatment equipment
|
To be used outside buildings, for rain water, faecal and organic effluents |
|
3 (3) |
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
PRODUCT FAMILY
WASTE WATER ENGINEERING PRODUCTS OUTSIDE BUILDINGS (2/3)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
Product(s) |
Intended use(s) |
Level(s) or class(es) |
Attestation of conformity system(s) |
Prefabricated drainage channel |
To be used outside buildings, for waste water from buildings and civil engineering works including roads |
|
3 (4) |
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
PRODUCT FAMILY
WASTE WATER ENGINEERING PRODUCTS OUTSIDE BUILDINGS (3/3)
Systems of attestation of conformity
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
Product(s) |
Intended use(s) |
Level(s) or class(es) |
Attestation of conformity system(s) |
Manholes and inspection chambers Covers, step irons, ladders and handrail for manholes and inspection chambers, gully tops |
To be used on carriageways, parking areas, hard shoulders and outside buildings |
|
4 (5) |
Separators |
For waste water/sewage from buildings and civil engineering works including roads |
|
4 (5) |
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
(1) System 4: See Annex III point 2 (ii) to Directive 89/106/EEC, third possibility.
(2) System 3: See Annex III point 2 (ii) to Directive 89/106/EEC, second possibility.
(3) System 3: See Annex III point 2 (ii) to Directive 89/106/EEC, second possibility.
(4) System 3: See Annex III point 2 (ii) of Directive 89/106/EEC, second possibility.
(5) System 4: See Annex III point 2 (ii) to Directive 89/106/EEC, third possibility.