ISSN 1977-0677

Official Journal

of the European Union

L 351

European flag  

English edition

Legislation

Volume 60
30 December 2017


Contents

 

II   Non-legislative acts

page

 

 

REGULATIONS

 

*

Council Regulation (EU) 2017/2466 of 18 December 2017 amending Regulation (EU) No 1388/2013 opening and providing for the management of autonomous tariff quotas of the Union for certain agricultural and industrial products

1

 

*

Council Regulation (EU) 2017/2467 of 21 December 2017 amending Regulation (EU) No 1387/2013 suspending the autonomous Common Customs Tariff duties on certain agricultural and industrial products

7

 

*

Commission Implementing Regulation (EU) 2017/2468 of 20 December 2017 laying down administrative and scientific requirements concerning traditional foods from third countries in accordance with Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods ( 1 )

55

 

*

Commission Implementing Regulation (EU) 2017/2469 of 20 December 2017 laying down administrative and scientific requirements for applications referred to in Article 10 of Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods ( 1 )

64

 

*

Commission Implementing Regulation (EU) 2017/2470 of 20 December 2017 establishing the Union list of novel foods in accordance with Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods ( 1 )

72

 

 

Corrigenda

 

*

Corrigendum to Commission Implementing Regulation (EU) 2017/2330 of 14 December 2017 concerning the authorisation of Iron(II) carbonate, Iron(III) chloride hexahydrate, Iron(II) sulphate monohydrate, Iron(II) sulphate heptahydrate, Iron(II) fumarate, Iron(II) chelate of amino acids hydrate, Iron(II) chelate of protein hydrolysates and Iron(II) chelate of glycine hydrate as feed additives for all animal species and of Iron dextran as feed additive for piglets and amending Regulations (EC) No 1334/2003 and (EC) No 479/2006 ( OJ L 333, 15.12.2017 )

202

 


 

(1)   Text with EEA relevance.

EN

Acts whose titles are printed in light type are those relating to day-to-day management of agricultural matters, and are generally valid for a limited period.

The titles of all other Acts are printed in bold type and preceded by an asterisk.

This issue closes the L series for 2017.


II Non-legislative acts

REGULATIONS

30.12.2017   

EN

Official Journal of the European Union

L 351/1


COUNCIL REGULATION (EU) 2017/2466

of 18 December 2017

amending Regulation (EU) No 1388/2013 opening and providing for the management of autonomous tariff quotas of the Union for certain agricultural and industrial products

THE COUNCIL OF THE EUROPEAN UNION,

Having regard to the Treaty on the Functioning of the European Union, and in particular Article 31 thereof,

Having regard to the proposal from the European Commission,

Whereas:

(1)

In order to ensure the sufficient and uninterrupted supply of certain goods insufficiently produced in the Union and to avoid disturbances on the market for certain agricultural and industrial products, autonomous tariff quotas were opened by Council Regulation (EU) No 1388/2013 (1). Products within those tariff quotas can be imported into the Union at reduced or zero duty rates.

(2)

For those reasons, it is necessary to open, with effect from 1 January 2018, tariff quotas at zero duty rates for an appropriate volume as regards 12 new products. In the case of five additional products, the quota volumes should be increased, as an increase is in the interests of economic operators of the Union.

(3)

In the case of one additional product, the quota volume should be decreased, as the production capacity of the Union producers has been increased.

(4)

In the case of five products, the quota period and the quota volume should be adapted, as they had been opened for a period of 6 months only.

(5)

In the case of another product, its description should be amended.

(6)

In the case of 12 other products, the autonomous tariff quotas of the Union should be closed with effect from 1 January 2018, as it is not in the Union's interest to maintain those quotas as from that date.

(7)

Regulation (EU) No 1388/2013 should therefore be amended accordingly.

(8)

In order to avoid any interruption of the application of the quota scheme and to comply with the guidelines set out in the Communication from the Commission concerning autonomous tariff suspensions and quotas (2), the changes provided for in this Regulation regarding the quotas for the products concerned have to apply from 1 January 2018. This Regulation should therefore enter into force as a matter of urgency,

HAS ADOPTED THIS REGULATION:

Article 1

The Annex to Regulation (EU) No 1388/2013 is amended as follows:

(1)

the rows for the tariff quotas with order numbers 09.2872, 09.2874, 09.2878, 09.2880, 09.2886, 09.2876, 09.2888, 09.2866, 09.2906, 09.2909, 09.2910 and 09.2932 set out in Annex I to this Regulation are inserted into the table according to the order of the CN codes indicated in the second column;

(2)

in the table, the rows for the tariff quotas with order numbers 09.2828, 09.2929, 09.2704, 09.2842, 09.2844, 09.2671, 09.2846, 09.2723, 09.2848, 09.2870, 09.2662, 09.2850 and 09.2868 are replaced by the corresponding rows set out in Annex II to this Regulation;

(3)

in the table, the rows for the tariff quotas with order numbers 09.2703, 09.2691, 09.2692, 09.2680, 09.2977, 09.2693, 09.2712, 09.2714, 09.2666, 09.2687, 09.2689 and 09.2669 are deleted;

(4)

endnote (*) containing the text ‘A newly introduced measure or a measure with amended conditions.’ is deleted.

Article 2

This Regulation shall enter into force on the day following that of its publication in the Official Journal of the European Union.

It shall apply from 1 January 2018.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 18 December 2017.

For the Council

The President

K. SIMSON


(1)  Council Regulation (EU) No 1388/2013 of 17 December 2013 opening and providing for the management of autonomous tariff quotas of the Union for certain agricultural and industrial products, and repealing Regulation (EU) No 7/2010 (OJ L 354, 28.12.2013, p. 319).

(2)  OJ C 363, 13.12.2011, p. 6.


ANNEX I

In the table in the Annex to Regulation (EU) No 1388/2013, the following rows are inserted according to the order of the CN codes indicated in the second column of that table:

Order number

CN code

TARIC

Description

Quota period

Quota volume

Quota duty (%)

‘09.2872

ex 2833 29 80

40

Cesium sulphate (CAS RN 10294-54-9) in solid form or as aqueous solution containing by weight 48 % or more but not more than 52 % of cesium sulphate

1.1.-31.12.

160 tonnes

0

09.2874

ex 2924 29 70

87

Paracetamol (INN) (CAS RN 103-90-2)

1.1.-31.12.

20 000 tonnes

0

09.2878

ex 2933 29 90

85

Enzalutamide INN (CAS RN 915087-33-1)

1.1.-31.12.

1 000 kg

0

09.2880

ex 2933 59 95

39

Ibrutinib (INN) (CAS RN 936563-96-1)

1.1.-31.12.

5 tonnes

0

09.2886

ex 2934 99 90

51

Canagliflozin (INN) (CAS RN 928672-86-0)

1.1.-31.12.

10 tonnes

0

09.2876

ex 3811 29 00

55

Additives consisting of reaction products of diphenylamine and branched nonenes with:

by weight more than 28 %, but not more than 35 % of 4-monononyldiphenylamine, and

by weight more than 50 % but not more than 65 % of 4,4′-dinonyldiphenylamine,

by weight a total percentage of 2, 4-dinonyldiphenylamine and 2, 4′-dinonyldiphenylamine of not more than 5 %,

used for the manufacture of lubricating oils (2)

1.1.-31.12.

900 tonnes

0

09.2888

ex 3824 99 92

89

Mixture of tertiary alkyldimethyl amines containing by weight:

60 % or more but not more than 80 % of dodecyldimethylamine (CAS RN 112-18-5), and

20 % or more but not more than 30 % of dimethyl(tetradecyl)amine (CAS RN 112-75-4)

1.1.-31.12.

16 000 tonnes

0

09.2866

ex 7019 12 00

ex 7019 12 00

06

26

S glass stratifils (rovings):

composed of continuous glass filaments of 9 μm (± 0,5 μm),

measuring 200 tex or more but not more than 680 tex,

not containing any calcium oxide, and

with a breaking strength of more than 3 550 Mpa determined by ASTM D2343-09

for use in the manufacture of aeronautics (2)

1.1.-31.12.

1 000 tonnes

0

09.2906

ex 7609 00 00

20

Aluminium tube or pipe fittings for affixing to radiators of motor bikes (2)

1.1.-31.12.

3 000 000 pieces

0

09.2909

ex 8481 80 85

40

Exhaust valve for use in the manufacture of motorcycle exhaust gas systems (2)

1.1.-31.12.

1 000 000 pieces

0

09.2910

ex 8708 99 97

75

Aluminium alloy support bracket, with mounting holes, whether or not with fixation nuts, for indirect connection of the gearbox to the car body for use in the manufacture of goods of Chapter 87 (2)

1.1.-31.12.

200 000 pieces

0

09.2932

ex 9027 10 90

20

Lambda sensors for permanent incorporation into motor cycle exhaust systems (2)

1.1.-31.12.

1 000 000 pieces

0’.


(2)  Suspension of duties is subject to end-use customs supervision in accordance with Article 254 of Regulation (EU) No 952/2013 of the European Parliament and of the Council of 9 October 2013 laying down the Union Customs Code (OJ L 269, 10.10.2013, p. 1).


ANNEX II

In the table in the Annex to Regulation (EU) No 1388/2013, the rows for the tariff quotas with order numbers 09.2828, 09.2929, 09.2704, 09.2842, 09.2844, 09.2671, 09.2846, 09.2723, 09.2848, 09.2870, 09.2662, 09.2850 and 09.2868 are replaced by the following:

Order number

CN code

TARIC

Description

Quota period

Quota volume

Quota duty (%)

‘09.2828

2712 20 90

 

Paraffin wax containing by weight less than 0,75 % of oil

1.1.-31.12.

120 000 tonnes

0

09.2929

2903 22 00

 

Trichloroethylene (CAS RN 79-01-6)

1.1.-31.12.

15 000 tonnes

0

09.2704

ex 2909 49 80

20

2,2,2′,2′-Tetrakis(hydroxymethyl)-3,3′-oxydipropan-1-ol (CAS RN 126-58-9)

1.1.-31.12.

500 tonnes

0

09.2842

2932 12 00

 

2-Furaldehyde (furfuraldehyde)

1.1.-31.12.

10 000 tonnes

0

09.2844

ex 3824 99 92

71

Mixtures containing by weight:

60 % or more but not more than 90 % of 2-chloropropene (CAS RN 557-98-2),

8 % or more but not more than 14 % of (Z)-1-chloropropene (CAS RN 16136-84-8),

5 % or more but not more than 23 % of 2-chloropropane (CAS RN 75-29-6),

not more than 6 % of 3-chloropropene (CAS RN 107-05-1), and

not more than 1 % of ethyl chloride (CAS RN 75-00-3)

1.1.-31.12.

6 000 tonnes

0

09.2671

ex 3905 99 90

81

Poly(vinyl butyral)(CAS RN 63148-65-2):

containing by weight 17,5 % or more, but not more than 20 % of hydroxyl groups, and

with a median particle size (D50) of more than 0,6 mm

1.1.-31.12.

12 500 tonnes

0

09.2846

ex 3907 40 00

25

Polymer blend of polycarbonate and poly(methyl methacrylate) with a polycarbonate content of not less than 98,5 % by weight, in the form of pellets or granules, with a luminous transmittance of not less than 88,5 %, measured using a test sample with a thickness of 4 mm at a wavelength of λ = 400 nm (according to ISO 13468-2)

1.1.-31.12.

2 000 tonnes

0

09.2723

ex 3911 90 19

10

Poly(oxy-1,4-phenylenesulphonyl-1,4-phenyleneoxy-4,4′-biphenylene)

1.1.-31.12.

3 500 tonnes

0

09.2848

ex 5505 10 10

10

Waste of synthetic fibres (including noils, yarn waste, and garnetted stock) of nylon or other polyamides (PA6 and PA66)

1.1.-31.12.

10 000 tonnes

0

09.2870

ex 7019 40 00

ex 7019 52 00

70

30

E-fibre glass fabrics:

having a weight of 20 g/m2 or more, but not more than 214 g/m2,

impregnated with silane,

in rolls,

having a humidity content by weight of 0,13 % or less, and

having not more than 3 hollow fibres out of 100 000 fibres,

for the exclusive use in the manufacture of prepregs and copper clad laminates (2)

1.1.-31.12.2018

6 000 000 m

0

09.2662

ex 7410 21 00

55

Plates:

consisting of at least one layer of fibreglass fabric impregnated with epoxide resin,

covered on one or both sides with copper foil with a thickness of not more than 0,15 mm,

with a dielectric constant (DK) of less than 5,4 at 1 MHz, as measured according to IPC-TM-650 2.5.5.2,

with a loss tangent of less than 0,035 at 1 MHz, as measured according to IPC-TM-650 2.5.5.2,

with a comparative tracking index (CTI) of 600 or more

1.1.-31.12.

80 000 m2

0

09.2850

ex 8414 90 00

70

Aluminium alloy compressor wheel with:

a diameter of 20 mm or more, but not more than 130 mm, and

a weight of 5 g or more, but not more than 800 g

for use in the manufacture of combustion engines (2)

1.1.-31.12.

5 900 000 pieces

0

09.2868

ex 8714 10 90

60

Pistons for suspension systems, having a diameter of not more than 55 mm, of sintered steel

1.1.-31.12.

2 000 000 pieces

0’.


(2)  Suspension of duties is subject to end-use customs supervision in accordance with Article 254 of Regulation (EU) No 952/2013 of the European Parliament and of the Council of 9 October 2013 laying down the Union Customs Code (OJ L 269, 10.10.2013, p. 1).


30.12.2017   

EN

Official Journal of the European Union

L 351/7


COUNCIL REGULATION (EU) 2017/2467

of 21 December 2017

amending Regulation (EU) No 1387/2013 suspending the autonomous Common Customs Tariff duties on certain agricultural and industrial products

THE COUNCIL OF THE EUROPEAN UNION,

Having regard to the Treaty on the Functioning of the European Union, and in particular Article 31 thereof,

Having regard to the proposal from the European Commission,

Whereas:

(1)

The Union production of 67 products that are not listed in the Annex to Council Regulation (EU) No 1387/2013 (1) is not sufficient to cover the needs of the Union industry. It is therefore in the interest of the Union to suspend the autonomous Common Customs Tariff (‘CCT’) duties on those products.

(2)

It is necessary to modify the conditions for the suspension of autonomous CCT duties for 49 products listed in the Annex to Regulation (EU) No 1387/2013 in order to take into account technical product developments and economic trends on the market. Certain product classifications have been amended in order to allow industry to fully benefit from the suspensions in force. Moreover, the Annex to Regulation (EU) No 1387/2013 should be updated in order to align or clarify texts in some cases. The modified conditions relate to changes in the product description, classification, duty rates or end-use requirements.

(3)

The end dates for the mandatory review provided for in the Annex to Regulation (EU) No 1387/2013 should be revised for 188 suspensions.

(4)

It is no longer in the interest of the Union to maintain the suspension of autonomous CCT duties for 92 products listed in the Annex to Regulation (EU) No 1387/2013. Suspensions for those products should therefore be deleted from that Annex.

(5)

In the interests of clarity, the entries for the suspensions that are modified or newly introduced by this Regulation should be marked with an asterisk, whereas the asterisk should be removed from the entries for the suspensions that are not modified by this Regulation.

(6)

Regulation (EU) No 1387/2013 should therefore be amended accordingly.

(7)

In order to avoid any interruption of the application of the autonomous suspension scheme and to comply with the guidelines set out in the Communication from the Commission concerning autonomous tariff suspensions and quotas (2), the changes provided for in this Regulation regarding the suspensions for the products concerned have to apply from 1 January 2018. This Regulation should therefore enter into force as a matter of urgency,

HAS ADOPTED THIS REGULATION:

Article 1

The Annex to Regulation (EU) No 1387/2013 is amended as follows:

(1)

in the table, the rows for the products for which the CN and TARIC codes are set out in Annex I to this Regulation are deleted;

(2)

all asterisks in the table and endnote (*), containing the text ‘A newly introduced measure or a measure with amended conditions.’, are deleted;

(3)

the rows for the products listed in Annex II to this Regulation are inserted into the table according to the order of the CN codes indicated in the first column of that table.

Article 2

This Regulation shall enter into force on the day following that of its publication in the Official Journal of the European Union.

It shall apply from 1 January 2018.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 21 December 2017.

For the Council

The President

M. MAASIKAS


(1)  Council Regulation (EU) No 1387/2013 of 17 December 2013 suspending the autonomous Common Customs Tariff duties on certain agricultural and industrial products and repealing Regulation (EU) No 1344/2011 (OJ L 354, 28.12.2013, p. 201).

(2)  OJ C 363, 13.12.2011, p. 6.


ANNEX I

In the table set out in the Annex to Regulation (EU) No 1387/2013, the rows relating to suspensions for the products identified by the following CN and TARIC codes are deleted:

CN code

TARIC

ex 1511 90 19

20

ex 1511 90 91

20

ex 1513 11 10

20

ex 1513 19 30

20

ex 1513 21 10

20

ex 1513 29 30

20

ex 2007 99 50

81

ex 2007 99 50

82

ex 2007 99 50

83

ex 2007 99 50

84

ex 2007 99 50

85

ex 2007 99 50

91

ex 2007 99 50

92

ex 2007 99 50

93

ex 2007 99 50

94

ex 2007 99 50

95

ex 2007 99 93

10

ex 2008 93 91

20

ex 2008 99 49

70

ex 2008 99 99

11

ex 2804 50 90

10

ex 2805 19 90

20

ex 2811 19 80

30

ex 2811 22 00

70

ex 2816 40 00

10

ex 2823 00 00

10

ex 2823 00 00

20

ex 2825 10 00

10

ex 2825 60 00

10

ex 2835 10 00

10

ex 2837 20 00

20

ex 2839 19 00

10

ex 2841 80 00

10

ex 2841 90 85

10

ex 2850 00 20

30

ex 2850 00 20

50

2903 39 31

 

ex 2903 39 35

10

ex 2903 89 80

50

ex 2904 99 00

40

ex 2905 19 00

70

ex 2905 19 00

80

ex 2905 39 95

20

ex 2905 39 95

40

ex 2906 29 00

30

ex 2907 29 00

55

ex 2908 99 00

40

ex 2909 60 00

40

ex 2912 29 00

50

ex 2912 49 00

20

ex 2914 19 90

20

ex 2914 19 90

30

ex 2914 19 90

40

ex 2914 39 00

30

ex 2914 39 00

70

ex 2914 39 00

80

ex 2914 50 00

45

ex 2914 50 00

60

ex 2914 50 00

70

ex 2914 79 00

20

ex 2915 60 19

10

ex 2915 90 70

30

ex 2915 90 70

75

ex 2916 12 00

70

ex 2916 13 00

10

ex 2916 39 90

55

ex 2916 39 90

75

ex 2916 39 90

85

ex 2917 19 10

20

ex 2917 39 95

70

ex 2918 29 00

35

ex 2918 30 00

50

ex 2918 99 90

15

ex 2920 29 00

50

ex 2920 29 00

60

ex 2920 90 10

60

ex 2920 90 70

40

ex 2920 90 70

50

2921 13 00

 

ex 2921 19 99

70

ex 2921 30 99

40

ex 2921 42 00

86

ex 2921 42 00

87

ex 2921 42 00

88

ex 2921 43 00

80

ex 2921 49 00

85

ex 2921 59 90

30

ex 2921 59 90

60

ex 2922 19 00

20

ex 2922 19 00

25

ex 2922 49 85

20

ex 2922 49 85

60

ex 2924 19 00

80

ex 2924 29 70

51

ex 2924 29 70

53

ex 2924 29 70

86

ex 2924 29 70

87

ex 2925 19 95

20

ex 2925 19 95

30

ex 2927 00 00

80

ex 2928 00 90

60

ex 2929 10 00

20

ex 2929 10 00

55

ex 2929 10 00

80

ex 2930 20 00

10

ex 2930 90 98

65

ex 2930 90 98

66

ex 2930 90 98

68

ex 2930 90 98

83

ex 2931 39 90

08

ex 2931 39 90

25

ex 2932 14 00

10

ex 2932 20 90

20

ex 2932 20 90

40

ex 2932 99 00

25

ex 2932 99 00

80

ex 2933 19 90

80

ex 2933 19 90

85

ex 2933 29 90

80

ex 2933 39 99

12

ex 2933 39 99

18

ex 2933 39 99

50

ex 2933 39 99

57

ex 2933 49 10

30

ex 2933 49 90

25

ex 2933 59 95

77

ex 2933 59 95

88

ex 2933 79 00

30

ex 2933 99 80

18

ex 2933 99 80

24

ex 2933 99 80

28

ex 2933 99 80

43

ex 2933 99 80

47

ex 2933 99 80

51

ex 2934 10 00

15

ex 2934 10 00

25

ex 2934 10 00

35

ex 2934 20 80

40

ex 2934 30 90

10

ex 2934 99 90

14

ex 2934 99 90

18

ex 2934 99 90

22

ex 2934 99 90

35

ex 2934 99 90

37

ex 2934 99 90

38

ex 2934 99 90

74

ex 2935 90 90

73

ex 2940 00 00

40

ex 3204 11 00

30

ex 3204 11 00

70

ex 3204 11 00

80

ex 3204 12 00

20

ex 3204 12 00

30

ex 3204 13 00

20

ex 3204 13 00

30

ex 3204 13 00

40

ex 3204 17 00

12

ex 3204 17 00

60

ex 3204 17 00

75

ex 3204 17 00

80

ex 3204 17 00

85

ex 3204 17 00

88

ex 3204 19 00

52

ex 3204 19 00

84

ex 3204 19 00

85

ex 3205 00 00

20

ex 3207 40 85

40

ex 3208 90 19

25

ex 3208 90 19

35

ex 3208 90 19

75

ex 3208 90 91

20

ex 3215 11 90

10

ex 3215 19 90

10

ex 3215 19 90

20

ex 3402 13 00

20

ex 3707 90 29

50

ex 3802 90 00

11

ex 3808 91 90

60

ex 3808 93 15

10

ex 3811 21 00

30

ex 3811 21 00

50

ex 3811 21 00

60

ex 3811 21 00

70

ex 3811 21 00

85

ex 3811 29 00

20

ex 3811 29 00

30

ex 3811 29 00

40

ex 3811 29 00

50

ex 3811 29 00

55

ex 3811 90 00

40

ex 3812 39 90

80

ex 3815 19 90

87

ex 3815 90 90

16

ex 3815 90 90

18

ex 3815 90 90

71

ex 3815 90 90

85

ex 3824 99 92

22

ex 3824 99 92

35

ex 3824 99 92

39

ex 3824 99 92

44

ex 3824 99 92

47

ex 3824 99 92

48

ex 3824 99 92

49

ex 3824 99 92

50

ex 3824 99 92

80

ex 3824 99 92

83

ex 3824 99 92

86

ex 3824 99 93

57

ex 3824 99 93

63

ex 3824 99 93

77

ex 3824 99 93

83

ex 3824 99 93

88

ex 3824 99 96

50

ex 3824 99 96

79

ex 3824 99 96

85

ex 3824 99 96

87

ex 3902 10 00

10

ex 3902 10 00

50

ex 3903 90 90

15

ex 3904 69 80

85

ex 3905 30 00

10

ex 3905 91 00

30

ex 3906 90 90

27

ex 3907 20 20

20

ex 3907 30 00

60

ex 3907 69 00

50

ex 3907 99 80

25

ex 3907 99 80

60

ex 3907 99 80

70

ex 3908 90 00

60

ex 3909 40 00

30

ex 3910 00 00

50

ex 3911 90 19

30

ex 3911 90 99

53

ex 3911 90 99

57

ex 3919 10 80

40

ex 3919 10 80

45

ex 3919 10 80

47

ex 3919 10 80

53

ex 3919 10 80

55

ex 3919 90 80

25

ex 3919 90 80

32

ex 3919 90 80

34

ex 3919 90 80

36

ex 3919 90 80

38

ex 3919 90 80

40

ex 3919 90 80

42

ex 3919 90 80

43

ex 3919 90 80

44

ex 3919 90 80

45

ex 3919 90 80

47

ex 3919 90 80

53

ex 3919 90 80

60

ex 3920 10 28

93

ex 3920 10 40

30

ex 3920 10 89

50

ex 3920 20 29

55

ex 3920 20 29

94

ex 3920 20 80

93

ex 3920 20 80

95

ex 3920 49 10

95

ex 3920 62 19

60

ex 3920 99 28

55

ex 3921 13 10

20

ex 3921 90 60

95

ex 3926 90 92

40

ex 3926 90 97

20

ex 3926 90 97

77

ex 4104 41 19

10

ex 5407 10 00

10

ex 5603 11 10

20

ex 5603 11 90

20

ex 5603 12 90

50

ex 6909 19 00

15

ex 7005 10 30

10

ex 7009 10 00

50

ex 7019 12 00

05

ex 7019 12 00

25

ex 7019 19 10

15

ex 7019 19 10

50

ex 7409 19 00

10

ex 7410 21 00

70

ex 7601 20 20

10

ex 7607 20 90

10

ex 7616 99 90

75

ex 8102 10 00

10

ex 8105 90 00

10

ex 8108 20 00

50

ex 8108 90 30

20

ex 8108 90 50

10

ex 8108 90 50

15

ex 8108 90 50

30

ex 8108 90 50

35

ex 8108 90 50

50

ex 8108 90 50

60

ex 8108 90 50

75

ex 8113 00 90

10

ex 8207 30 10

10

ex 8407 33 20

10

ex 8407 33 80

10

ex 8407 90 80

10

ex 8407 90 90

10

ex 8408 90 43

40

ex 8408 90 45

30

ex 8408 90 47

50

ex 8409 91 00

20

ex 8409 91 00

30

ex 8409 99 00

50

ex 8411 99 00

60

ex 8411 99 00

65

ex 8414 59 25

30

ex 8415 90 00

50

ex 8431 20 00

30

ex 8481 80 69

60

ex 8482 10 10

30

ex 8482 10 90

20

ex 8483 30 38

40

ex 8501 10 99

60

ex 8501 31 00

25

ex 8501 31 00

33

ex 8501 31 00

35

ex 8501 32 00

70

ex 8501 62 00

30

ex 8503 00 99

40

ex 8504 31 80

20

ex 8504 31 80

40

ex 8504 40 82

40

ex 8504 50 95

50

ex 8505 11 00

35

ex 8505 11 00

50

ex 8505 11 00

60

ex 8506 90 00

10

ex 8507 60 00

25

ex 8507 60 00

50

ex 8507 60 00

53

ex 8507 60 00

55

ex 8507 60 00

57

ex 8511 30 00

50

ex 8512 90 90

10

ex 8516 90 00

70

ex 8518 29 95

30

ex 8522 90 80

15

ex 8522 90 80

96

ex 8525 80 19

45

ex 8529 90 65

75

ex 8529 90 92

70

ex 8536 69 90

51

ex 8536 69 90

81

ex 8536 69 90

88

ex 8536 90 95

30

ex 8537 10 91

30

ex 8537 10 98

92

ex 8544 20 00

20

ex 8544 30 00

35

ex 8544 30 00

80

ex 8544 42 90

30

ex 8544 42 90

60

ex 8548 10 29

10

ex 8548 90 90

50

ex 8704 23 91

20

ex 8708 40 20

10

ex 8708 40 50

20

ex 8708 50 20

30

ex 8708 50 99

20

ex 8708 93 10

20

ex 8708 93 90

20

ex 8708 99 10

20

ex 8708 99 97

70

ex 9001 20 00

10

ex 9001 20 00

40

ex 9001 50 41

30

ex 9001 50 49

30

ex 9001 90 00

25

ex 9001 90 00

60

ex 9001 90 00

75

ex 9002 11 00

20

ex 9002 11 00

30

ex 9002 11 00

40

ex 9002 11 00

70

ex 9002 11 00

80

ex 9002 90 00

40

ex 9032 89 00

40


ANNEX II

In the table set out in the Annex to Regulation (EU) No 1387/2013, the following rows are inserted according to the order of the CN codes indicated in the first column of that table:

CN code

TARIC

Description

Rate of autonomous duty

Supplementary Unit

Date foreseen for mandatory review

*ex 1511 90 19

*ex 1511 90 91

*ex 1513 11 10

*ex 1513 19 30

*ex 1513 21 10

*ex 1513 29 30

20

20

20

20

20

20

Palm oil, coconut (copra) oil, palm kernel oil, for the manufacture of:

industrial monocarboxylic fatty acids of subheading 3823 19 10 ,

methyl esters of fatty acids of heading 2915 or 2916 ,

fatty alcohols of subheadings 2905 17 , 2905 19 and 3823 70 used for the manufacture of cosmetics, washing products or pharmaceutical products,

fatty alcohols of subheading 2905 16 , pure or mixed, used for the manufacture of cosmetics, washing products or pharmaceutical products,

stearic acid of subheading 3823 11 00 ,

goods of heading 3401 , or

fatty acids with high purity of heading 2915  (2)

0 %

31.12.2018

*ex 2007 99 50

*ex 2007 99 50

*ex 2007 99 93

83

93

10

Mango puree concentrate, obtained by cooking:

of the Genus Mangifera spp.,

with a sugar content by weight of not more than 30 %

for use in the manufacture of products of food and drink industry (2)

6 % (3)

31.12.2022

*ex 2007 99 50

*ex 2007 99 50

84

94

Papaya puree concentrate, obtained by cooking:

of the Genus Carica spp.,

with a sugar content by weight of more than 13 % but not more than 30 %

for use in the manufacture of products of food and drink industry (2)

7,8 % (3)

31.12.2022

*ex 2007 99 50

*ex 2007 99 50

85

95

Guava puree concentrate, obtained by cooking:

of the Genus Psidium spp.,

with a sugar content by weight of more than 13 % but not more than 30 %

for use in the manufacture of products of food and drink industry (2)

6 % (3)

31.12.2022

*ex 2008 93 91

20

Sweetened dried cranberries, excluding packing alone as processing, for the manufacture of products of food processing industries (4)

0 %

31.12.2022

*ex 2008 99 49

*ex 2008 99 99

70

11

Blanched vine leaves of the genus Karakishmish, in brine, containing by weight:

more than 6 % of salt concentration,

0,1 % or more but not more than 1,4 % of acidity expressed as citric acid monohydrate and

whether or not but not more than 2 000  mg/kg of sodium benzoate according CODEX STAN 192-1995

for use in the manufacture of stuffed vine leaves with rice (2)

0 %

31.12.2022

*ex 2106 90 92

50

Casein protein hydrolysate consisting of:

by weight 20 % or more but not more than 70 % free amino acids, and

peptones of which by weight more than 90 % having a molecular weight of not more than 2 000 Da

0 %

kg

31.12.2022

*ex 2804 50 90

40

Tellurium (CAS RN 13494-80-9) of a purity by weight of 99,99 % or more, but not more than 99,999 %, based on metallic impurities measured by ICP analysis

0 %

31.12.2018

*ex 2805 19 90

20

Lithium metal (CAS RN 7439-93-2) of a purity by weight of 98,8 % or more

0 %

31.12.2022

*ex 2811 22 00

15

Amorphous silicon dioxide (CAS RN 60676-86-0),

in the form of powder

of a purity by weight of 99,0 % or more

with a median grain size of 0,7 μm or more, but not more than 2,1 μm

where 70 % of the particles have a diameter of not more than 3 μm

0 %

31.12.2020

*ex 2811 29 90

10

Tellurium dioxide (CAS RN 7446-07-3)

0 %

31.12.2022

*ex 2816 40 00

10

Barium hydroxide (CAS RN 17194-00-2)

0 %

31.12.2022

*ex 2823 00 00

10

Titanium dioxide (CAS RN 13463-67-7):

of a purity by weight of 99,9 % or more,

with an average grain-size of 0,7 μm or more but not more than 2,1 μm

0 %

31.12.2022

*ex 2825 10 00

10

Hydroxylammonium chloride (CAS RN 5470-11-1)

0 %

31.12.2022

*ex 2825 60 00

10

Zirconium dioxide (CAS RN 1314-23-4)

0 %

31.12.2022

*ex 2835 10 00

10

Sodium hypophosphite monohydrate (CAS RN 10039-56-2)

0 %

31.12.2022

*ex 2837 20 00

20

Ammonium iron (III) hexacyanoferrate (II) (CAS RN 25869-00-5)

0 %

31.12.2022

*ex 2839 19 00

10

Disodium disilicate (CAS RN 13870-28-5)

0 %

31.12.2022

*ex 2841 50 00

10

Potassium dichromate (CAS RN 7778-50-9)

0 %

31.12.2022

*ex 2841 80 00

10

Diammonium wolframate (ammonium paratungstate) (CAS RN 11120-25-5)

0 %

31.12.2022

*ex 2841 90 30

10

Potassium metavanadate (CAS RN 13769-43-2)

0 %

kg

31.12.2022

*ex 2841 90 85

10

Lithium cobalt(III) oxide (CAS RN 12190-79-3) with a cobalt content of at least 59 %

0 %

31.12.2022

*ex 2850 00 20

30

Titanium nitride (CAS RN 25583-20-4) with a particle size of not more than 250 nm

0 %

31.12.2022

*ex 2850 00 20

60

Disilane (CAS RN 1590-87-0)

0 %

31.12.2022

*ex 2903 39 19

20

5-Bromopent-1-ene (CAS RN 1119-51-3)

0 %

31.12.2022

*2903 39 31

 

2,3,3,3-Tetrafluoroprop-1-ene (2,3,3,3-tetrafluoropropene) (CAS RN 754-12-1)

0 %

31.12.2022

*ex 2903 39 35

20

Trans-1,3,3,3-tetrafluoroprop-1-ene (Trans-1,3,3,3-tetrafluoropropene) (CAS RN 29118-24-9)

0 %

31.12.2018

*ex 2903 39 39

40

1,1,2,3,4,4-hexafluorobuta-1,3-diene (CAS RN 685-63-2)

0 %

31.12.2022

*ex 2903 89 80

50

Chlorocyclopentane (CAS RN 930-28-9)

0 %

31.12.2022

*ex 2903 89 80

60

Octafluorocyclobutane (CAS RN 115-25-3)

0 %

31.12.2022

*ex 2904 99 00

40

4-Chlorobenzenesulphonyl chloride (CAS RN 98-60-2)

0 %

31.12.2022

*ex 2905 19 00

70

Titanium tetrabutanolate (CAS RN 5593-70-4)

0 %

31.12.2022

*ex 2905 19 00

80

Titanium tetraisopropoxide (CAS RN 546-68-9)

0 %

31.12.2022

*ex 2905 39 95

20

Butane-1,2-diol (CAS RN 584-03-2)

0 %

31.12.2022

*ex 2905 39 95

40

Decane-1,10-diol (CAS RN 112-47-0)

0 %

31.12.2022

*ex 2906 29 00

30

2-Phenylethanol (CAS RN 60-12-8)

0 %

31.12.2022

*ex 2908 99 00

40

4,5-Dihydroxynaphthalene-2,7-disulphonic acid (CAS RN 148-25-4)

0 %

31.12.2018

*ex 2912 29 00

35

Cinnamaldehyde (CAS RN 104-55-2)

0 %

kg

31.12.2022

*ex 2912 29 00

50

4-Isobutylbenzaldehyde (CAS RN 40150-98-9)

0 %

31.12.2018

*ex 2912 49 00

20

4-Hydroxybenzaldehyde (CAS RN 123-08-0)

0 %

31.12.2022

*ex 2914 19 90

20

Heptan-2-one (CAS RN 110-43-0)

0 %

31.12.2022

*ex 2914 19 90

30

3-Methylbutanone (CAS RN 563-80-4)

0 %

31.12.2022

*ex 2914 19 90

40

Pentan-2-one (CAS RN 107-87-9)

0 %

31.12.2022

*ex 2914 39 00

30

Benzophenone (CAS RN 119-61-9)

0 %

31.12.2022

*ex 2914 39 00

70

Benzil (CAS RN 134-81-6)

0 %

31.12.2022

*ex 2914 39 00

80

4′-Methylacetophenone (CAS RN 122-00-9)

0 %

31.12.2022

*ex 2914 50 00

45

3,4-Dihydroxybenzophenone (CAS RN 10425-11-3)

0 %

31.12.2022

*ex 2914 50 00

60

2,2-Dimethoxy-2-phenylacetophenone (CAS RN 24650-42-8)

0 %

31.12.2022

*ex 2914 79 00

20

2,4′-Difluorobenzophenone (CAS RN 342-25-6)

0 %

31.12.2022

*ex 2915 60 19

10

Ethyl butyrate (CAS RN 105-54-4)

0 %

31.12.2022

*ex 2915 90 70

30

3,3-Dimethylbutyryl chloride (CAS RN 7065-46-5)

0 %

31.12.2022

*ex 2916 12 00

70

2-(2-Vinyloxyethoxy)ethyl acrylate (CAS RN 86273-46-3)

0 %

31.12.2022

*ex 2916 13 00

30

Zinc monomethacrylate powder (CAS RN 63451-47-8) whether or not containing not more than 17 % by weight of manufacturing impurities

0 %

31.12.2020

*ex 2916 39 90

55

4-tert-Butylbenzoic acid (CAS RN 98-73-7)

0 %

31.12.2022

*ex 2916 39 90

75

m-Toluic acid (CAS RN 99-04-7)

0 %

31.12.2022

*ex 2916 39 90

85

(2,4,5-Trifluorophenyl)acetic acid (CAS RN 209995-38-0)

0 %

31.12.2022

*ex 2917 19 10

20

Diethyl malonate (CAS RN 105-53-3)

0 %

31.12.2022

*ex 2918 29 00

35

Propyl 3,4,5-trihydroxybenzoate (CAS RN 121-79-9)

0 %

31.12.2022

*ex 2918 30 00

50

Ethyl acetoacetate (CAS RN 141-97-9)

0 %

31.12.2022

*ex 2918 99 90

15

Ethyl 2,3-epoxy-3-phenylbutyrate (CAS RN 77-83-8)

0 %

31.12.2022

*ex 2918 99 90

27

Ethyl 3-ethoxypropionate (CAS RN 763-69-9)

0 %

31.12.2022

*ex 2920 29 00

15

Phosphorous acid 3,3′,5,5′-tetrakis(1,1-dimethylethyl)-6,6′-dimethyl[1,1′-biphenyl]-2,2′-diyl tetra-1-naphthalenyl ester (CAS RN 198979-98-5)

0 %

31.12.2022

*ex 2920 29 00

50

Fosetyl-aluminium (CAS RN 39148-24-8)

0 %

31.12.2018

*ex 2920 29 00

60

Fosetyl-sodium (CAS RN 39148-16-8) in form of an aqueous solution with a content by weight of fosetyl-sodium of 35 % or more but not more than 45 % for use in the manufacture of pesticides (2)

0 %

31.12.2021

*ex 2920 90 10

60

2,4-Di-tert-butyl-5-nitrophenyl methyl carbonate (CAS RN 873055-55-1)

0 %

31.12.2022

*2921 13 00

 

2-(N,N-Diethylamino)ethyl chloride hydrochloride (CAS RN 869-24-9)

0 %

31.12.2022

*ex 2921 19 99

70

N,N-Dimethyloctylamine – boron trichloride (1:1) (CAS RN 34762-90-8)

0 %

31.12.2022

*ex 2921 30 99

40

Cyclopropylamine (CAS RN 765-30-0)

0 %

31.12.2022

*ex 2921 42 00

86

2,5-Dichloroaniline (CAS RN 95-82-9)

0 %

31.12.2022

*ex 2921 42 00

87

N-Methylaniline (CAS RN 100-61-8)

0 %

31.12.2022

*ex 2921 42 00

88

3,4-Dichloroaniline-6-sulphonic acid (CAS RN 6331-96-0)

0 %

31.12.2022

*ex 2921 43 00

80

6-Chloro-α,α,α-trifluoro-m-toluidine (CAS RN 121-50-6)

0 %

31.12.2018

*ex 2921 45 00

60

1-Naphthylamine (CAS RN 134-32-7)

0 %

31.12.2022

*ex 2921 45 00

70

8-Aminonaphthalene-2-sulphonic acid (CAS RN 119-28-8)

0 %

31.12.2022

*ex 2921 59 90

30

3,3′-Dichlorobenzidine dihydrochloride (CAS RN 612-83-9)

0 %

31.12.2022

*ex 2921 59 90

60

(2R,5R)-1,6-Diphenylhexane-2,5-diamine dihydrochloride (CAS RN 1247119-31-8)

0 %

31.12.2022

*ex 2922 19 00

20

2-(2-Methoxyphenoxy)ethylamine hydrochloride (CAS RN 64464-07-9)

0 %

31.12.2022

*ex 2922 49 85

20

3-Amino-4-chlorobenzoic acid (CAS RN 2840-28-0)

0 %

31.12.2022

*ex 2922 49 85

60

Ethyl-4-dimethylaminobenzoate (CAS RN 10287-53-3)

0 %

31.12.2022

*ex 2922 49 85

75

L-alanine isopropyl ester hydrochloride (CAS RN 62062-65-1)

0 %

31.12.2022

*ex 2922 50 00

15

3,5-Diiodothyronine (CAS RN 1041-01-6)

0 %

31.12.2022

*ex 2924 19 00

25

Isobutylidenediurea (CAS RN 6104-30-9)

0 %

31.12.2022

*ex 2924 19 00

80

Tetrabutylurea (CAS RN 4559-86-8)

0 %

31.12.2022

*ex 2924 29 70

53

4-Amino-N-[4-(aminocarbonyl)phenyl]benzamide (CAS RN 74441-06-8)

0 %

31.12.2022

*ex 2924 29 70

86

Anthranilamide (CAS RN 88-68-6) of a purity by weight of 99,5 % or more

0 %

31.12.2022

*ex 2925 19 95

20

4,5,6,7-Tetrahydroisoindole-1,3-dione (CAS RN 4720-86-9)

0 %

31.12.2022

*ex 2925 19 95

30

N,N′-(m-Phenylene)dimaleimide (CAS RN 3006-93-7)

0 %

31.12.2022

*ex 2927 00 00

80

4-[(2,5-Dichlorophenyl)azo]-3-hydroxy-2-naphthoic acid (CAS RN 51867-77-7)

0 %

31.12.2022

*ex 2929 10 00

20

Butyl isocyanate (CAS RN 111-36-4)

0 %

31.12.2022

*ex 2929 10 00

55

2,5 (and 2,6)-Bis(isocyanatomethyl)bicyclo[2.2.1]heptane (CAS RN 74091-64-8)

0 %

31.12.2022

*ex 2929 10 00

80

1,3-Bis(isocyanatomethyl)benzene (CAS RN 3634-83-1)

0 %

31.12.2022

*ex 2930 20 00

10

Prosulfocarb (ISO) (CAS RN 52888-80-9)

0 %

31.12.2022

*ex 2930 90 98

65

Pentaerythritol tetrakis(3-mercaptopropionate) (CAS RN 7575-23-7)

0 %

31.12.2022

*ex 2930 90 98

68

Clethodim (ISO) (CAS RN 99129-21-2)

0 %

31.12.2022

*ex 2931 39 90

08

Sodium diisobutyldithiophosphinate (CAS RN 13360-78-6) in an aqueous solution

0 %

31.12.2022

*ex 2931 39 90

25

(Z)-Prop-1-en-1-ylphosphonic acid (CAS RN 25383-06-6)

0 %

31.12.2022

*ex 2931 90 00

20

Ferrocene (CAS RN 102-54-5)

0 %

31.12.2022

*ex 2932 14 00

10

1,6-Dichloro-1,6-dideoxy-β-D-fructofuranosyl-4-chloro-4 deoxy-α-D-galactopyranoside (CAS RN 56038-13-2)

0 %

31.12.2019

*ex 2932 20 90

40

(S)-(–)-α-Amino-γ-butyrolactone hydrobromide (CAS RN 15295-77-9)

0 %

31.12.2022

*ex 2932 20 90

50

L-Lactide (CAS RN 4511-42-6) or D-Lactide (CAS RN 13076-17-0) or dilactide (CAS RN 95-96-5)

0 %

t

31.12.2022

*ex 2932 99 00

25

1-(2,2-Difluorobenzo[d][1,3]dioxol-5-yl)cyclopropanecarboxylic acid (CAS RN 862574-88-7)

0 %

31.12.2022

*ex 2932 99 00

80

1,3:2,4-bis-O-(4-Methylbenzylidene)-D-glucitol (CAS RN 81541-12-0)

0 %

31.12.2018

*ex 2933 19 90

80

3-(4,5-Dihydro-3-methyl-5-oxo-1H-pyrazol-1-yl)benzenesulphonic acid (CAS RN 119-17-5)

0 %

31.12.2022

*ex 2933 29 90

80

Imazalil (ISO) (CAS RN 35554-44-0)

0 %

31.12.2022

*ex 2933 39 99

12

2,3-Dichloropyridine (CAS RN 2402-77-9)

0 %

31.12.2022

*ex 2933 39 99

36

1-[2-[5-Methyl-3-(trifluoromethyl)-1H-pyrazol-1-yl]acetyl]piperidine-4-carbothioamide (CAS RN 1003319-95-6)

0 %

31.12.2022

*ex 2933 39 99

57

Tert-butyl 3-(6-amino-3-methylpyridin-2-yl)benzoate (CAS RN 1083057-14-0)

0 %

31.12.2022

*ex 2933 49 10

30

Ethyl 4-oxo-1,4-dihydroquinoline-3-carboxylate (CAS RN 52980-28-6)

0 %

31.12.2022

*ex 2933 49 90

25

Cloquintocet-mexyl (ISO) (CAS RN 99607-70-2)

0 %

31.12.2021

*ex 2933 59 95

77

3-(Trifluoromethyl)-5,6,7,8-tetrahydro[1,2,4]triazolo[4,3-a]pyrazine hydrochloride (1:1) (CAS RN 762240-92-6)

0 %

31.12.2022

*ex 2933 79 00

30

5-Vinyl-2-pyrrolidone (CAS RN 7529-16-0)

0 %

31.12.2022

*ex 2933 99 80

24

1,3-Dihydro-5,6-diamino-2H-benzimidazol-2-one (CAS RN 55621-49-3)

0 %

31.12.2022

*ex 2933 99 80

41

5-[4′-(bromomethyl)biphenyl-2-yl]-1-trityl-1H-tetrazole (CAS RN 124750-51-2)

0 %

31.12.2022

*ex 2933 99 80

46

(S)-indoline-2-carboxylic acid (CAS RN 79815-20-6)

0 %

31.12.2022

*ex 2933 99 80

47

Paclobutrazol (ISO) (CAS RN 76738-62-0)

0 %

31.12.2022

*ex 2933 99 80

51

Diquat dibromide (ISO) (CAS RN 85-00-7) in aqueous solution for use in the manufacture of herbicides (2)

0 %

31.12.2021

*ex 2934 10 00

15

4-Nitrophenyl thiazol-5-ylmethyl carbonate (CAS RN 144163-97-3)

0 %

31.12.2022

*ex 2934 10 00

25

(S)-Ethyl-2-(3-((2-isopropylthiazol-4-yl)methyl)-3-methylureido)-4-morpholinobutanoate oxalate (CAS RN 1247119-36-3)

0 %

31.12.2022

*ex 2934 10 00

35

(2-Isopropylthiazol-4-yl)-N-methylmethanamine dihydrochloride (CAS RN 1185167-55-8)

0 %

31.12.2022

*ex 2934 20 80

15

Benthiavalicarb-isopropyl (ISO) (CAS RN 177406-68-7)

0 %

kg

31.12.2022

*ex 2934 20 80

40

1,2-Benzisothiazol-3(2H)-one (Benzisothiazolinone (BIT)) (CAS RN 2634-33-5)

0 %

31.12.2022

*ex 2934 30 90

10

2-Methylthiophenothiazine (CAS RN 7643-08-5)

0 %

31.12.2022

*ex 2934 99 90

37

4-Propan-2-ylmorpholine (CAS RN 1004-14-4)

0 %

31.12.2022

*ex 2934 99 90

52

Epoxiconazole (ISO) (CAS RN 133855-98-8)

0 %

31.12.2022

*ex 2934 99 90

54

2-benzyl-2-dimethylamino-4′-morpholinobutyrophenone (CAS RN 119313-12-1)

0 %

kg

31.12.2022

*ex 2934 99 90

56

1-[5-(2,6-Difluorophenyl)-4,5-dihydro-1,2-oxazol-3-yl]ethanone (CAS RN 1173693-36-1)

0 %

31.12.2022

*ex 2934 99 90

57

(6R,7R)-7-Amino-8-oxo-3-(1-propenyl)-5-thia-1-azabicyclo[4.2.0]oct-2-ene-2-carboxylic acid (CAS RN 120709-09-3)

0 %

31.12.2022

*ex 2934 99 90

58

Dimethenamide-P (CAS RN 163515-14-8)

0 %

31.12.2018

*ex 2934 99 90

74

2-Isopropylthioxanthone (CAS RN 5495-84-1)

0 %

31.12.2022

*ex 2935 90 90

73

(2S)-2-Benzyl-N,N-dimethylaziridine-1-sulfonamide (CAS RN 902146-43-4)

0 %

31.12.2022

*ex 2938 90 90

30

Rebaudioside A (CAS RN 58543-16-1)

0 %

31.12.2022

*ex 2938 90 90

40

Purified steviol glycoside with a rebaudioside M (CAS RN 1220616-44-3) content of 80 % or more but not more than 90 % by weight for use in the manufacture of non-alcoholic beverages (2)

0 %

31.12.2022

*ex 3204 11 00

35

Colourant C.I Disperse Yellow 232 (CAS RN 35773-43-4) and preparations based thereon with a colourant C.I Disperse Yellow 232 content of 50 % or more

0 %

31.12.2022

*ex 3204 11 00

45

Preparation of dispersion dyes, containing:

C.I. Disperse Orange 61 or Disperse Orange 288,

C.I. Disperse Blue 291:1,

C.I. Disperse Violet 93:1,

whether or not containing C.I. Disperse Red 54

0 %

31.12.2020

*ex 3204 13 00

30

Colourant C.I. Basic Blue 7 (CAS RN 2390-60-5) and preparations based thereon with a colourant C.I. Basic Blue 7 content of 50 % or more by weight

0 %

31.12.2018

*ex 3204 13 00

40

Colourant C.I. Basic Violet 1 (CAS RN 603-47-4 or CAS RN 8004-87-3) and preparations based thereon with a colourant C.I. Basic Violet 1 content of 90 % or more by weight

0 %

31.12.2022

*ex 3204 15 00

80

Colourant C.I. Vat Blue 1 (CAS RN 482-89-3) and preparations based thereon with a colourant C.I. Vat Blue 1 content of 94 % or more by weight

0 %

31.12.2022

*ex 3204 17 00

26

Colourant C.I. Pigment Orange 13 (CAS RN 3520-72-7) and preparations based thereon with a colourant C.I. Pigment Orange 13 content of 80 % or more by weight

0 %

31.12.2022

*ex 3204 17 00

75

Colourant C.I. Pigment Orange 5 (CAS RN 3468-63-1) and preparations based thereon with a colourant C.I. Pigment Orange 5 content of 80 % or more by weight

0 %

31.12.2022

*ex 3204 17 00

80

Colourant C.I. Pigment Red 207 (CAS RN 71819-77-7) and preparations based thereon with a colourant C.I. Pigment Red 207 content of 50 % or more by weight

0 %

31.12.2022

*ex 3204 17 00

85

Colourant C.I. Pigment Blue 61 (CAS RN 1324-76-1) and preparations based thereon with a colourant C.I. Pigment Blue 61 content of 35 % or more by weight

0 %

31.12.2022

*ex 3204 17 00

88

Colourant C.I. Pigment Violet 3 (CAS RN 1325-82-2 or CAS RN 101357-19-1) and preparations based thereon with a colourant C.I. Pigment Violet 3 content of 90 % or more by weight

0 %

31.12.2022

*ex 3204 19 00

16

Colourant C.I Solvent Yellow 133 (CAS RN 51202-86-9) and preparations based thereon with a colourant C.I. Solvent Yellow 133 content of 97 % or more by weight

0 %

31.12.2022

*ex 3204 19 00

84

Colourant C.I. Solvent Blue 67 (CAS RN 12226-78-7) and preparations based thereon with a colourant C.I. Solvent Blue 67 content of 98 % or more by weight

0 %

31.12.2022

*ex 3204 90 00

20

Preparations of colourant C.I. Solvent Red 175 (CAS RN 68411-78-6) in petroleum distillates, hydrotreated light naphthenic (CAS RN 64742-53-6), containing by weight 40 % or more but not more than 60 % C.I. Solvent Red 175

0 %

31.12.2022

*ex 3206 49 70

30

Colourant C.I. Pigment Black 12 (CAS RN 68187-02-0) and preparations based thereon with a colourant C.I. Pigment Black 12 content of 50 % or more by weight

0 %

31.12.2022

*ex 3207 40 85

40

Glass flakes (CAS RN 65997-17-3):

of a thickness of 0,3 μm or more but not more than 10 μm, and

coated with titanium dioxide (CAS RN 13463-67-7) or iron oxide (CAS RN 18282-10-5)

0 %

31.12.2022

*ex 3208 90 19

*ex 3208 90 91

25

20

Tetrafluoroethylene copolymer in butylacetate solution with a content of solvent of 50 % (± 2 %) by weight

0 %

31.12.2022

*ex 3208 90 19

65

Silicones containing 50 % by weight or more of xylene and not more than 25 % by weight of silica, of a kind used for the manufacture of long term surgical implants

0 %

31.12.2018

*ex 3208 90 19

75

Acenaphthalene copolymer in ethyl lactate solution

0 %

31.12.2022

*ex 3215 11 00

*ex 3215 19 00

10

10

Printing ink, liquid, consisting of a dispersion of a vinyl acrylate copolymer and colour pigments in isoparaffins, containing by weight not more than 13 % of vinyl acrylate copolymer and colour pigments

0 %

31.12.2018

*ex 3215 19 00

20

Ink:

consisting of a polyester polymer and a dispersion of silver (CAS RN 7440-22-4) and silver chloride (CAS RN 7783-90-6) in methyl propyl ketone (CAS RN 107-87-9),

with a total solid content by weight of 55 % or more, but not more than 57 %, and

with a specific gravity of 1,40 g/cm3 or more, but not more than 1,60 g/cm3,

for use in the manufacture of electrodes (2)

0 %

l

31.12.2022

*ex 3402 13 00

20

Surfactant containing 1,4-dimethyl-1,4-bis(2-methylpropyl)-2-butyne-1,4-diyl ether, polymerised with oxirane, methyl terminated

0 %

31.12.2022

*ex 3506 91 90

60

Temporary wafer-bonding adhesive material in the form of a suspension of a solid polymer in D-limonene (CAS RN 5989-27-5) with a polymeric content by weight of 65 % or more but not more than 75 %

0 %

l

31.12.2022

*ex 3506 91 90

70

Temporary wafer-bonding release in form of a suspension of a solid polymer in cyclopentanone (CAS RN 120-92-3) with a polymeric content of not more than 10 % by weight

0 %

l

31.12.2022

*ex 3603 00 60

10

Igniters for gas generators with an overall maximum length of 20,34 mm or more but not more than 25,25 mm and a pin length of 6,68 mm (± 0,3 mm) or more but not more than 6,9 mm (± 0,3 mm)

0 %

31.12.2022

*ex 3707 90 29

50

Dry ink powder or toner blend, consisting of:

styrene acrylate/butadiene copolymer

either carbon black or an organic pigment

whether or not containing polyolefin or amorphous silica

for use as a developer in the manufacturing of ink/toner filled bottles or cartridges for facsimile machines, computer printers and copiers (2)

0 %

31.12.2022

*ex 3801 90 00

20

Pitch coated graphite based powder with:

an average particle size of 10,8 μm or more but not more than 13,0 μm,

an iron content of less than 40 ppm,

a copper content of less than 5 ppm,

a nickel content of less than 5 ppm,

an average surface area (N2 atmosphere) of 3,0 m2/g or more but not more than 4,36 m2/g, and

a magnetic metal impurity of less than 0,3 ppm

0 %

kg

31.12.2022

*ex 3808 91 90

60

Spinetoram (ISO) (CAS RN 935545-74-7), preparation of two spinosyn components (3′-ethoxy-5,6-dihydro spinosyn J) and (3′-ethoxy- spinosyn L)

0 %

31.12.2022

*ex 3811 21 00

30

Additives for lubricating oils, containing mineral oils, consisting of calcium salts of reaction products of polyisobutylene substituted phenol with salicylic acid and formaldehyde, used as a concentrated additive for the manufacture of engine oils through a blending process

0 %

31.12.2022

*ex 3811 21 00

50

Additives for lubricating oils,

based on calcium C16-24 alkylbenzenesulphonates (CAS RN 70024-69-0),

containing mineral oils,

used as a concentrated additive for the manufacture of engine oils through a blending process

0 %

31.12.2022

*ex 3811 21 00

60

Additives for lubricating oils, containing mineral oils,

based on calcium polypropylenyl substituted benzenesulphonate (CAS RN 75975-85-8) with a content by weight of 25 % or more but not more than 35 %,

with a total base number (TBN) of 280 or more but not more than 320,

used as a concentrated additive for the manufacture of engine oils through a blending process

0 %

31.12.2022

*ex 3811 21 00

70

Additives for lubricating oils,

containing polyisobutylene succinimide derived from reaction products of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 84605-20-9),

containing mineral oils,

with a chlorine content by weight of 0,05 % or more but not more than 0,25 %,

with a total base number (TBN) of more than 20,

used as a concentrated additive for the manufacture of engine oils through a blending process

0 %

31.12.2022

*ex 3811 21 00

85

Additives,

containing more than 20 % or more but not more than 45 % by weight of mineral oils,

based on a mixture of branched dodecylphenol sulfide calcium salts, whether or not carbonated,

of a kind used in the manufacture of blends of additives for lubricating oils

0 %

31.12.2022

*ex 3811 29 00

20

Additives for lubricating oils, consisting of reaction products of bis(2-methylpentan-2-yl)dithiophosphoric acid with propylene oxide, phosphorus oxide, and amines with C12-14 alkyl chains, used as a concentrated additive for the manufacture of lubricating oils

0 %

31.12.2022

*ex 3811 29 00

30

Additives for lubricating oils, consisting of reaction products of butyl-cyclohex-3-enecarboxylate, sulphur and triphenyl phosphite (CAS RN 93925-37-2), used as a concentrated additive for the manufacture of engine oils through a blending process

0 %

31.12.2022

*ex 3811 29 00

40

Additives for lubricating oils, consisting of reaction products of 2-methyl-prop-1-ene with sulphur monochloride and sodium sulphide (CAS RN 68511-50-2), with a chlorine content by weight of 0,01 % or more but not more than 0,5 %, used as a concentrated additive for the manufacture of lubricating oils

0 %

31.12.2022

*ex 3811 29 00

50

Additives for lubricating oils, consisting of a mixture of N,N-dialkyl -2-hydroxyacetamides with alkyl chain lengths between 12 and 18 carbon atoms (CAS RN 866259-61-2), used as a concentrated additive for the manufacture of engine oils through a blending process

0 %

31.12.2022

*ex 3811 90 00

40

Solution of a quaternary ammonium salt based on polyisobutenyl succinimide, containing by weight 20 % or more but not more than 29,9 % of 2-ethylhexanol

0 %

31.12.2022

*ex 3812 39 90

80

UV-stabilizer, consisting of:

a hindered amine: N,N′-bis(1,2,2,6,6-pentamethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4-dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 193098-40-7) and

either an o-hydroxyphenyl triazine UV light absorber or

a chemically modified phenolic compound

0 %

31.12.2022

*ex 3815 19 90

*ex 8506 90 00

87

10

Cathode, in rolls, for air zinc button cell batteries (hearing aid batteries) (2)

0 %

31.12.2018

*ex 3815 90 90

16

Initiator based on dimethylaminopropyl urea

0 %

31.12.2022

*ex 3815 90 90

18

Oxidation catalyst with an active ingredient of di[manganese (1+)], 1,2-bis(octahydro-4,7-dimethyl-1H-1,4,7-triazonine-1-yl-kN1, kN4, kN7)ethane-di-μ-oxo-μ-(ethanoato-kO, kO′)-, di[chloride(1-)],(CAS RN 1217890-37-3) used to accelerate chemical oxidation or bleaching

0 %

31.12.2022

*ex 3815 90 90

22

Catalyst in powder form consisting by weight of 95 % (± 1 %) titanium dioxide and 5 % (± 1 %) silicon dioxide

0 %

31.12.2022

*ex 3815 90 90

85

Catalyst based on aluminosilicate (zeolite), for the alkylation of aromatic hydrocarbons, for the transalkylation of alkylaromatic hydrocarbons or for the oligomerization of olefins (2)

0 %

31.12.2022

*ex 3824 99 92

26

Preparation containing by weight:

60 % or more but not more than 75 % of Solvent naphtha (petroleum), heavy aromatic (CAS RN 64742-94-5)

15 % or more but not more than 25 % of 4-(4-nitrophenylazo)-2,6-di-sec-butyl-phenol (CAS RN 111850-24-9), and

10 % or more but not more than 15 % of 2-sec-butylphenol (CAS RN 89-72-5)

0 %

31.12.2022

*ex 3824 99 92

28

Aqueous solution containing by weight

10 % or more but not more than 42 % of 2-(3-chloro-5-(trifluoromethyl)pyridin-2-yl)ethanamine (CAS RN 658066-44-5),

10 % or more but not more than 25 % of sulphuric acid (CAS RN 7664-93-9) and

0,5 % or more but not more than 2,9 % of methanol (CAS RN 67-56-1)

0 %

31.12.2020

*ex 3824 99 92

29

Preparation containing by weight:

85 % or more but not more than 99 % of polyethylene glycol ether of butyl 2-cyano 3-(4-hydroxy-3-methoxyphenyl) acrylate, and

1 % or more but not more than 15 % of polyoxyethylene (20) sorbitan trioleate

0 %

31.12.2020

*ex 3824 99 92

35

Preparations containing not less than 92 % or more but not more than 96,5 % by weight of 1,3:2,4-bis-O-(4-methylbenzylidene)-D-glucitol and also containing carboxylic acid derivatives and an alkyl sulphate

0 %

31.12.2018

*ex 3824 99 92

39

Preparation containing not less than 47 % by weight of 1,3:2,4-bis-O-benzylidene-D-glucitol

0 %

31.12.2018

*ex 3824 99 92

47

Preparation, containing:

trioctylphosphine oxide (CAS RN 78-50-2),

dioctylhexylphosphine oxide (CAS RN 31160-66-4),

octyldihexylphosphine oxide (CAS RN 31160-64-2) and

trihexylphosphine oxide (CAS RN 3084-48-8)

0 %

31.12.2022

*ex 3824 99 92

49

Preparation based on 2,5,8,11-tetramethyl-6-dodecyn-5,8-diol ethoxylate (CAS RN 169117-72-0)

0 %

31.12.2022

*ex 3824 99 92

50

Alkyl carbonate-based preparation, also containing a UV absorber, for use in the manufacture of spectacle lenses (2)

0 %

31.12.2022

*ex 3824 99 92

80

Diethylene glycol propylene glycol triethanolamine titanate complexes (CAS RN 68784-48-5) dissolved in diethylene glycol (CAS RN 111-46-6)

0 %

31.12.2022

*ex 3824 99 93

30

Powder Mixture containing by weight:

85 % or more of zinc diacrylate (CAS RN 14643-87-9),

not more than 5 % of 2,6-di-tert-butyl-alpha-dimethylamino-p-cresol (CAS RN 88-27-7), and

not more than 10 % of zinc stearate (CAS RN 557-05-1)

0 %

31.12.2018

*ex 3824 99 93

63

Mixture of phytosterols, not in the form of powder, containing by weight:

75 % or more of sterols,

not more than 25 % of stanols,

for use in the manufacture of stanols/sterols or stanol/sterol esters (2)

0 %

31.12.2022

*ex 3824 99 93

*ex 3824 99 96

83

85

Preparation containing:

C,C′-azodi(formamide) (CAS RN 123-77-3),

magnesium oxide (CAS RN 1309-48-4) and

zinc bis(p-toluene sulphinate) (CAS RN 24345-02-6)

in which the gas formation from C,C′-azodi(formamide) occurs at 135 °C

0 %

31.12.2018

*ex 3824 99 93

88

Mixture of phytosterols derived from wood and wood based oils (tall oil), in the form of powder, containing by weight:

60 % or more, but not more than 80 % of sitosterols,

not more than 15 % of campesterols,

not more than 5 % of stigmasterols and

not more than 15 % of betasitostanols

0 %

31.12.2022

*ex 3824 99 96

45

Lithium nickel cobalt aluminum oxide powder (CAS RN 177997-13-6) with:

a particle size of less than 10 μm,

a purity by weight of more than 98 %

0 %

kg

31.12.2022

*ex 3824 99 96

50

Nickel hydroxide, doped with 12 % or more but not more than 18 % by weight of zinc hydroxide and cobalt hydroxide, of a kind used to produce positive electrodes for accumulators

0 %

31.12.2022

*ex 3824 99 96

87

Platinum oxide (CAS RN 12035-82-4) fixed on a porous support of aluminium oxide (CAS RN 1344-28-1), containing by weight:

0,1 % or more but not more than 1 % of platinum, and

0,5 % or more but not more than 5 % of ethylaluminium dichloride (CAS RN 563-43-9)

0 %

31.12.2022

*ex 3903 90 90

15

Copolymer in the form of granules containing by weight:

78 (± 4 %) of styrene,

9 (± 2 %) of n-butyl acrylate,

11 (± 3 %) of n-butyl methacrylate,

1,5 (± 0,7 %) of methacrylic acid and

0,01 % or more but not more than 2,5 % of polyolefinic wax

0 %

31.12.2018

*ex 3904 69 80

85

Copolymer of ethylene with chlorotrifluoroethylene, whether or not modified with hexafluoroisobutylene, in powder, whether or not with fillers

0 %

31.12.2022

*ex 3905 30 00

10

Viscous preparation, essentially consisting of poly(vinyl alcohol) (CAS RN 9002-89-5), an organic solvent and water for use as protective coating of wafers during the manufacturing of semiconductors (2)

0 %

31.12.2022

*ex 3905 91 00

40

Water soluble copolymer of ethylene and vinyl alcohol (CAS RN 26221-27-2), containing by weight not more than 38 % of the monomer unit ethylene

0 %

31.12.2022

*ex 3906 90 90

27

Copolymer of stearyl methacrylate, isooctyl acrylate and acrylic acid, dissolved in isopropyl palmitate

0 %

31.12.2022

*ex 3907 20 20

20

Polytetramethylene ether glycol with a weight average molecular weight (Mw) of 2 700 or more but not more than 3 100 (CAS RN 25190-06-1)

0 %

31.12.2022

*ex 3907 20 20

60

Polypropylene glycol monobutyl ether (CAS RN 9003-13-8) of an alkalinity of not more than 1 ppm of sodium

0 %

31.12.2022

*ex 3907 20 99

80

Isoamyl alcohol polyoxyethylene ether (CAS RN 62601-60-9)

0 %

kg

31.12.2022

*ex 3907 30 00

60

Polyglycerol polyglycidyl ether resin (CAS RN 118549-88-5)

0 %

31.12.2022

*ex 3907 99 80

25

Copolymer, containing 72 % by weight or more of terephthalic acid and/or isomers thereof and cyclohexanedimethanol

0 %

31.12.2022

*ex 3907 99 80

70

Copolymer of poly(ethylene terephthalate) and cyclohexane dimethanol, containing more than 10 % by weight of cyclohexane dimethanol

3.5 %

31.12.2019

*ex 3910 00 00

50

Silicone based pressure sensitive adhesive in solvent containing copoly (dimethylsiloxane/diphenylsiloxane) gum

0 %

31.12.2022

*ex 3911 90 19

30

Copolymer of ethyleneimine and ethyleneimine dithiocarbamate, in an aqueous solution of sodium hydroxide

0 %

31.12.2022

*ex 3911 90 99

53

Hydrogenated polymer of 1,2,3,4,4a,5,8,8a-octahydro-1,4:5,8-dimethanonaphthalene with 3a,4,7,7a-tetrahydro-4,7-methano-1H-indene and 4,4a,9,9a-tetrahydro-1,4-methano-1H-fluorene (CAS RN 503442-46-4)

0 %

31.12.2022

*ex 3911 90 99

57

Hydrogenated polymer of 1,2,3,4,4a,5,8,8a-octahydro-1,4:5,8-dimethanonaphthalene with 4,4a,9,9a-tetrahydro-1,4-methano-1H-fluorene (CAS RN 503298-02-0)

0 %

31.12.2022

*ex 3919 10 80

*ex 3919 90 80

40

43

Black poly(vinyl chloride) film:

with a gloss of more than 30 degrees according to ASTM D2457,

whether or not covered on one side with a protective poly(ethyleneterephthalate) film, and on the other side with a pressure sensitive adhesive with channels and a release liner

0 %

31.12.2022

*ex 3919 10 80

*ex 3919 90 80

45

45

Reinforced polyethylene foam tape, coated on both sides with an acrylic micro channelled pressure sensitive adhesive and on one side a liner, with an application thickness of 0,38 mm or more but not more than 1,53 mm

0 %

31.12.2022

*ex 3919 10 80

*ex 3919 90 80

55

53

Acrylic foam tape, covered on one side with a heat activatable adhesive or an acrylic pressure sensitive adhesive and on the other side with an acrylic pressure sensitive adhesive and a release sheet, of a peel adhesion at an angle of 90° of more than 25 N/cm (as determined by the ASTM D 3330 method)

0 %

31.12.2022

*ex 3919 90 80

82

Reflecting film consisting of:

a polyurethane layer,

a glass microspheres layer,

a metallised aluminium layer, and

an adhesive, covered on one or both sides with a release liner,

whether or not a poly(vinyl chloride) layer,

a layer whether or not incorporating security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use

0 %

31.12.2020

*ex 3919 90 80

*ex 9001 90 00

83

33

Reflector or diffuser sheets, in rolls,

for protection against ultraviolet or infra-red heat radiation, to be affixed to windows or

for equal transmission and distribution of light, intended for LCD modules

0 %

31.12.2022

*ex 3920 20 29

94

Co-extruded trilayer film,

each layer containing a mixture of polypropylene and polyethylene,

containing not more than 3 % by weight of other polymers,

whether or not containing titanium dioxide in the core layer,

of an overall thickness of not more than 70 μm

0 %

31.12.2022

*ex 3920 62 19

60

Poly(ethylene terephthalate) film:

of a thickness of not more than 20 μm,

coated on at least one side with a gas barrier layer consisting of a polymeric matrix in which silica or aluminium oxide has been dispersed and of a thickness of not more than 2μm

0 %

31.12.2022

*ex 3920 99 28

55

Thermoplastic polyurethane film extruded, with:

not self-adhesive,

an index of yellow lower of more than 1,0 but not more than 2,5 for 10 mm stacked films (as determined by test method ASTM E 313-10),

a light transmission higher to 87 % for 10 mm stacked films (as determined by test method ASTM D 1003-11),

a total thickness of 0,38 mm or more, but not more than 7,6 mm,

a width of 99 cm or more, but not more than 305 cm,

of a kind used in the production of laminated safety glass

0 %

31.12.2018

*ex 3921 13 10

20

Rolls of open-cell polyurethane foam:

with a thickness of 2,29 mm (± 0,25 mm),

surface-treated with a foraminous adhesion promoter, and

laminated to a polyester film and a layer of textile material

0 %

31.12.2022

*ex 3921 19 00

60

Multi-porous multilayer separator foil with:

one microporous polyethylene layer between two microporous polypropylene layers and whether or not containing a coating of aluminium oxide on both sides,

a width of 65 mm or more but not more than 170 mm,

a total thickness of 0,01 mm or more but not more than 0,03 mm,

a porosity of 0,25 or more but not more than 0,65

0 %

m2

31.12.2022

*ex 3921 19 00

70

Microporous membranes of expanded Polytetrafluoroethylene (ePTFE) in rolls, having:

a width of 1 600 mm or more but not more than 1 730 mm, and

a membrane thickness of 15 μm or more, but not more than 50 μm

for use in the manufacture of a bi-component ePTFE membrane (2)

0 %

31.12.2022

*ex 3921 19 00

80

Microporous monolayer film of polypropylene or a microporous trilayer film of polypropylene, polyethylene and polypropylene, each film with

zero transversal production direction (TD) shrinkage,

a total thickness of 10 μm or more but not more than 50 μm,

a width of 15 mm or more but not more than 900 mm,

a length of more than 200 m but not more than 3 000 m, and

an average pore size between 0,02 μm and 0,1 μm

0 %

31.12.2022

*ex 3926 30 00

*ex 3926 90 97

30

34

Electroplated interior or exterior decorative parts consisting of:

a copolymer of acrylonitrile-butadiene-styrene (ABS), whether or not mixed with polycarbonate,

layers of copper, nickel and chromium

for use in the manufacturing of parts for motor vehicles of heading 8701 to 8705  (2)

0 %

p/st

31.12.2022

*ex 3926 90 97

33

Housings, housing parts, drums, setting wheels, frames, covers and other parts of acrylonitrile-butadiene-styrene or polycarbonate, of a kind used for the manufacture of remote controls

0 %

p/st

31.12.2019

*ex 3926 90 97

77

Silicone decoupling ring, with an inner diameter of 15,4 mm (+ 0,0 mm/– 0,1 mm), of a kind used in car parking aid sensor systems

0 %

p/st

31.12.2021

*ex 4104 41 19

10

Buffalo leather, split, chrome tanned synthetic retanned (‘crust’), dry

0 %

31.12.2022

*ex 5407 10 00

10

Textile fabric, consisting of warp filament yarns of polyamide-6,6 and weft filament yarns of polyamide-6,6, polyurethane and a copolymer of terephthalic acid, p-phenylenediamine and 3,4′–oxybis (phenyleneamine)

0 %

31.12.2022

*ex 5603 12 90

50

Non-woven:

weighing 30 g/m2 or more, but not more than 60 g/m2,

containing fibres of polypropylene or of polypropylene and polyethylene,

whether or not printed, with:

on one side, 65 % of the total surface area having circular bobbles of 4 mm in diameter, consisting of anchored, elevated un-bonded curly fibres, suitable for the engagement of extruded hook materials, and the remaining 35 % of the surface area being bonded,

and on other side a smooth untextured surface,

for use in the manufacture of napkins and napkin liners for babies and similar sanitary articles (2)

0 %

m2

31.12.2022

*ex 7009 10 00

50

Unfinished electro-chromic auto-dimming mirror for motor vehicle rear-view mirrors:

whether or not equipped with plastic backing plate,

whether or not equipped with a heating element,

whether or not equipped with Blind Spot Module (BSM) display

0 %

31.12.2022

*ex 7019 12 00

*ex 7019 12 00

05

25

Rovings ranging from 1 980 to 2 033 tex, composed of continuous glass filaments of 9 μm (± 0,5 μm)

0 %

31.12.2022

*ex 7019 19 10

15

S-glass yarn of 33 tex or a multiple of 33 tex (± 13 %) made from continuous spun-glass filaments with fibres of a diameter of 9 μm (– 1 μm / + 1,5 μm)

0 %

31.12.2022

*ex 7019 19 10

50

Yarn of 11 tex or a multiple thereof (± 7,5 %), obtained from continuous spun-glass filaments, containing 93 % by weight or more of silicon dioxide, of a nominal diameter of 6 μm or 9 μm, other than those treated

0 %

31.12.2022

*ex 7020 00 10

20

Raw material for optical elements of fused silicon dioxide with:

a thickness of 10 cm or more but not more than 40 cm and

a weight of 100 kg or more

0 %

31.12.2022

*ex 7315 11 90

10

Roller type steel timing chain with a fatigue limit of 2 kN at 7 000 rpm or more for use in the manufacture of engines of motor vehicles (2)

0 %

31.12.2022

*ex 7601 20 20

10

Slabs and billets of aluminium alloy containing lithium

0 %

31.12.2022

*ex 7608 20 20

*ex 8708 91 99

30

40

Assembly for supplying compressed air, whether or not with a resonator, comprising at least:

one solid aluminium tube whether or not with mounting bracket,

one flexible rubber hose, and

one metal clip

for use in the manufacture of goods of Chapter 87 (2)

0 %

31.12.2022

*ex 8101 96 00

20

Tungsten wire

containing by weight 99,95 % or more of tungsten, and

with a maximum cross-sectional dimension of not more than 1,02 mm

0 %

31.12.2022

*ex 8102 10 00

10

Molybdenum powder with:

a purity by weight of 99 % or more and

a particle size of 1,0 μm or more, but not more than 5,0 μm

0 %

31.12.2022

*ex 8105 90 00

10

Bars or wires made of cobalt alloy containing, by weight:

35 % (± 2 %) cobalt,

25 % (± 1 %) nickel,

19 % (± 1 %) chromium and

7 % (± 2 %) iron

conforming to the material specifications AMS 5842, of a kind used in the aerospace industry

0 %

31.12.2018

*ex 8108 20 00

55

Titanium alloy ingot,

with a height of 17,8 cm or more, a length of 180 cm or more, a width of 48,3 cm or more

a weight of 680 kg or more,

containing alloy elements by weight of:

3 % or more but not more than 7 % of aluminium,

1 % or more but not more than 5 % of tin,

3 % or more but not more than 5 % of zirconium,

4 % or more but not more than 8 % of molybdenum

0 %

31.12.2020

*ex 8108 20 00

70

Titanium alloy slab, with

a height of 20,3 cm or more, but not more than 23,3 cm,

a length of 246,1 cm or more, but not more than 289,6 cm,

a width of 40,6 cm or more, but not more than 46,7 cm,

a weight of 820 kg or more but not more than 965 kg,

containing alloy elements by weight of:

5,2 % or more but not more than 6,2 % of aluminium,

2,5 % or more but not more than 4,8 % of vanadium

0 %

31.12.2022

*ex 8108 90 30

15

Rods and wire of an alloy of titanium with:

a uniform solid cross-section in a form of a cylinder,

with a diameter of 0,8 mm or more, but not more than 5 mm,

an aluminium content by weight of 0,3 % or more, but not more than 0,7 %,

a silicon content by weight of 0,3 % or more, but not more than 0,6 %,

a niobium content by weight of 0,1 or more, but not more than 0,3 %, and

an iron content by weight of not more than 0,2 %

0 %

kg

31.12.2022

*ex 8108 90 50

45

Cold or hot rolled plates, sheets and strips of non-alloyed titanium with:

a thickness of 0,4 mm or more, but not more than 100 mm,

a length of not more than 14 m, and

a width of not more than 4 m

0 %

kg

31.12.2022

*ex 8108 90 50

55

Plates, sheets, strip and foil of an alloy of titanium

0 %

31.12.2021

*ex 8108 90 60

30

Seamless tubes and pipes of a titanium or an alloy of titanium with:

a diameter of 19 mm or more but not more than 159 mm,

a wall thickness of 0,4 mm or more but not more than 8 mm, and

a maximum length of 18 m

0 %

kg

31.12.2022

*ex 8113 00 90

10

Carrier plate of aluminium silicon carbide (AlSiC-9) for electronic circuits

0 %

31.12.2022

*ex 8207 30 10

10

Set of transfer and/or tandem press tools for cold-forming, pressing, drawing, cutting, punching, bending, calibrating, bordering and throating of metal sheets, for use in the manufacture of frame parts of motor vehicles (2)

0 %

p/st

31.12.2022

*ex 8407 33 20

*ex 8407 33 80

*ex 8407 90 80

*ex 8407 90 90

10

10

10

10

Spark-ignition reciprocating or rotary internal combustion piston engines, having a cylinder capacity of not less than 300 cm3 and a power of not less than 6 kW but not exceeding 20,0 kW, for the manufacture of:

self-propelled lawn mowers, with a seat of subheading 8433 11 51 , and hand-operated lawn mowers of heading 8433 11 90 ,

tractors of subheading 8701 91 90 , whose main function is that of a lawn mower,

four stroke mowers with motor of a cylinder capacity of not less than 300 cc of subheading 8433 20 10 or

snowploughs and snow blowers of subheading 8430 20  (2)

0 %

31.12.2022

*ex 8408 90 43

*ex 8408 90 45

*ex 8408 90 47

40

30

50

4 Cylinder, 4 cycle, liquid cooled, compression-ignition engine having:

a capacity of not more than 3 850 cm3, and

a rated output of 15 kW or more but not more than 85 kW,

for use in the manufacture of vehicles of heading 8427  (2)

0 %

31.12.2022

*ex 8409 91 00

40

Fuel injector with solenoid valve for optimized atomization in the combustion chamber for use in the manufacture of spark-ignition internal combustion piston engines of motor vehicles (2)

0 %

31.12.2021

*ex 8409 91 00

*ex 8409 99 00

50

55

exhaust manifold with turbine housing of turbochargers with:

a heat-resistance of not more than 1 050  °C, and

a hole to insert a turbine wheel, whereby the hole has a diameter of 28 mm or more, but not more than 130 mm

0 %

p/st

31.12.2018

*ex 8409 99 00

60

Intake manifold for air supply to the engine cylinders, comprising at least:

a throttle,

a boost pressure sensor

for use in the manufacture of compression ignition engines of motor vehicles (2)

0 %

31.12.2022

*ex 8409 99 00

70

Metal alloy intake and exhaust valve with a Rockwell hardness HRC 20 or more, but not more than HRC 50 for use in the manufacture of compression ignition engines of motor vehicles (2)

0 %

31.12.2021

*ex 8409 99 00

80

High pressure oil jet for engine piston cooling and lubrication with:

an opening pressure of 1 bar or more, but not more than 3 bar,

a closing pressure of more than 0,7 bar,

a one-way valve

for use in the manufacture of compression ignition engines of motor vehicles (2)

0 %

31.12.2022

*ex 8411 99 00

20

Wheel-shaped gas turbine component with blades, of a kind used in turbochargers:

of a precision-cast nickel based alloy complying with standard DIN G- NiCr13Al6MoNb or DIN G- NiCr13Al16MoNb or DIN G- NiCo10W10Cr9AlTi or DIN G- NiCr12Al6MoNb or AMS AISI:686,

with a heat-resistance of not more than 1 100 °C,

with a diameter of 28 mm or more, but not more than 180 mm,

with a height of 20 mm or more, but not more than 150 mm

0 %

p/st

31.12.2022

*ex 8411 99 00

30

Turbine housing of turbochargers with:

a heat-resistance of not more than 1 050  °C, and

a hole to insert a turbine wheel, whereby the hole has a diameter of 28 mm or more, but not more than 130 mm

0 %

p/st

31.12.2021

*ex 8414 80 22

*ex 8414 80 80

20

20

Air membrane compressor with:

a flow of 4,5 l/min or more, but not more than 7 l/min,

power input of not more than 8,1 W, and

a gauge pressure capacity not exceeding 400 hPa (0,4 bar)

of a kind used in the production of motor vehicle seats

0 %

31.12.2022

*ex 8415 90 00

55

Aluminium arc-welded removable receiver dryer with polyamide and ceramic elements with:

a length of 143 mm or more but not more than 292 mm,

a diameter of 31 mm or more but not more than 99 mm,

a spangle length of not more than 0,2 mm and a thickness of not more than 0,06 mm, and

a solid particle diameter of not more than 0,06 mm

of a kind used in car air-conditioning systems

0 %

p/st

31.12.2020

*ex 8431 20 00

30

Drive axle assembly containing differential, reduction gears, crown wheel, drive shafts, wheel hubs, brakes and mast mounting arms for use in the manufacture of vehicles in heading 8427  (2)

0 %

p/st

31.12.2022

*ex 8481 80 69

60

Four-way reversing valve for refrigerants, consisting of:

a solenoid pilot valve

a brass valve body including valve slider and copper connections

with a working pressure up to 4,5 MPa

0 %

p/st

31.12.2022

*ex 8482 10 10

*ex 8482 10 90

40

30

Ball bearings:

with an internal diameter of 3 mm or more,

with an external diameter of not more than 100 mm,

with a width of not more than 40 mm,

whether or not equipped with a duster,

for use in the manufacture of belt drive steering systems of motor, electric power steering systems or steering gears or assembly ball screw for steering gears (2)

0 %

p/st

31.12.2019

*ex 8483 30 32

*ex 8483 30 38

20

50

Bearing housing of a kind used in turbochargers:

of precision-cast grey cast iron complying with standard DIN EN 1561,

with oil chambers,

without bearings,

with a diameter of 50 mm or more, but not more than 250 mm,

with a height of 40 mm or more, but not more than 150 mm,

whether or not with water chambers and connectors

0 %

p/st

31.12.2022

*ex 8483 40 90

20

Hydrostatic transmission with:

measurements (without shafts) of not more than 154 mm × 115 mm × 108 mm,

a weight of not more than 3,3 kg,

a maximum rotation speed of the input shaft of 2 700 rpm or more, but not more than 3 200 rpm,

a torque of the output shaft of not more than 10,4 Nm,

a rotation speed of the output shaft of not more than 930 rpm at 2 800 rpm input speed, and

an operating temperature range of – 5 °C or more, but not more than + 40 °C

for use in the manufacture of hand-operated lawn mowers of heading 8433 11 90  (2)

0 %

31.12.2022

*ex 8483 40 90

30

Hydrostatic transmission with

a reduction of 20,63:1 or more, but not more than 22,68:1,

an input speed of 1 800 rpm or more when loaded and of not more than 3 000  rpm when unloaded,

a continuous output torque of 142 Nm or more, but not more than 156 Nm,

an intermittent output torque of 264 Nm or more, but not more than 291 Nm, and

an axle shaft diameter of 19,02 mm or more, but not more than 19,06 mm,

whether or not equipped with a fan impeller or with a pulley with integrated fan impeller

for use in the production of self-propelled lawn mowers with a seat of subheading 8433 11 51 , and tractors of subheading 8701 91 90 , whose main function is that of a lawn mower (2)

0 %

31.12.2022

*ex 8501 10 99

60

DC motor:

with a rotor speed of 3 500 rpm or more but not more than 5 000 rpm loaded and not more than 6 500 rpm when not loaded

with a power supply voltage of 100 V or more but not more than 240 V

for use in the manufacture of electric fryers (2)

0 %

31.12.2022

*ex 8501 20 00

30

Universal AC/DC motor with

a rated output of 1,2 kW,

a supply voltage of 230 V, and

engine brake,

assembled to a reduction gear with output shaft, which is contained in a plastic housing

for use as electric drive of lawnmower blades (2)

0 %

31.12.2022

*ex 8501 31 00

25

DC motors, brushless, with:

an external diameter of 80 mm or more, but not more than 100 mm,

a supply voltage of 12 V,

an output at 20 °C of 300 W or more, but not more than 750 W,

a torque 20 °C of 2,00 Nm or more, but not more than 7,00 Nm,

a rated speed at 20 °C of 600 rpm or more, but not more than 3 100 rpm,

with or without the rotor angle position sensor of resolver type or Hall effect type,

of the kind used in power steering systems for cars

0 %

31.12.2022

*ex 8501 31 00

75

Brushless DC motor assembly comprised of a motor and transmission, with:

electronic control operating by Hall Effect position sensors,

voltage input 9V or more but not more than 16 V,

external diameter of the motor 70 mm or more but not more than 80 mm,

output motor power 350 W or more but not more than 550 W,

maximum output torque 50 Nm or more but not more than 52 Nm,

maximum output rotation speed 280 rpm or more but not more than 300 rpm,

coaxial male spline outputs of outer diameter 20 mm (± 1 mm), 17 teeth and minimum length of teeth 25 mm (± 1 mm), and

with distance between root of splines 119 mm (± 1 mm)

for use in the manufacture of all-terrain or utility task vehicles (2)

0 %

31.12.2021

*ex 8501 31 00

*ex 8501 32 00

78

75

Automotive-ready, brushless and permanently excited direct current motor with:

a specified speed of not more than 4 100  rpm,

a minimum output of 400 W, but not more than 1,3 kW (at 12 V),

a flange diameter of 90 mm or more, but not more than 150 mm,

a maximum length of 200 mm, measured from the beginning of the shaft to the outer ending,

a housing length of not more than 160 mm, measured from the flange to the outer ending,

a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 6 bore holes) aluminium diecast housing whether or not with a sealing compound (groove with an O-ring and grease),

a stator with single T-tooth design and single coil windings in 12/8 topology, and

surface magnets

0 %

31.12.2020

*ex 8501 62 00

30

Fuel cell system

consisting of at least phosphoric acid fuel cells,

in a housing with integrated water management and gas treatment,

for permanent, stationary energy supply

0 %

31.12.2022

*ex 8503 00 99

40

Fuel cell membrane, in rolls or sheets, with a width of not more than 150 cm, of a kind used for manufacture of fuel cells in heading 8501

0 %

p/st

31.12.2022

*ex 8504 31 80

40

Electrical transformers:

with a capacity of 1 kVA or less

without plugs or cables,

for internal use in the manufacture of set top boxes and TVs (2)

0 %

31.12.2022

*ex 8504 40 82

40

Printed circuit board equipped with a bridge rectifier circuit and other active and passive components:

with two output connectors

with two input connectors which are available and useable in parallel

able to switch between bright and dimmed operation mode

with an input voltage of 40 V (+ 25 % -15 %) or 42 V (+ 25 % -15 %) in bright operation mode, with an input voltage of 30 V (± 4 V) in dimmed operation mode, or

with an input voltage of 230 V (+ 20 % -15 %) in bright operation mode, with an input voltage of 160 V (± 15 %) in dimmed operation mode, or

with an input voltage of 120 V (15 % -35 %) in bright operation mode, with an input voltage of 60 V (± 20 %) in dimmed operation mode

with an input current reaching 80 % of its nominal value within 20 ms

with an input frequency of 45 Hz or more, but not more than 65 Hz for 42 V and 230 V, and 45-70 Hz for 120 V versions

with an maximum inrush current overshoot of not more than 250 % of the input current

with a period of the inrush current overshoot of not more than 100 ms

with an input current undershoot of not less than 50 % of the input current

with a period of the inrush current undershoot of not more than 20 ms

with a presettable output current

with an output current reaching 90 % of its nominal pre-set value within 50 ms

with an output current reaching zero within 30 ms after removal of the input voltage

with an defined failure status in case of no-load or too-high load (end-of-life function)

0 %

p/st

31.12.2022

*ex 8504 40 82

50

Electric rectifier:

with an input AC voltage of 100-240 V at frequency of 50-60 Hz,

with two output DC voltages of 9 V or more but not more than 12 V and 396 V or more but not more than 420 V,

output cables without connectors, and

in a plastic enclosure with dimensions 110 mm (± 0,5 mm) × 60 mm (± 0,5 mm) × 38 mm (± 1 mm)

for use in the manufacture of products using IPL (Intensive Pulse Light) (2)

0 %

p/st

31.12.2022

*ex 8504 50 95

50

Solenoid coil with

a power consumption of not more than 6 W,

an insulation resistance of more than 100 M ohms, and

an insert hole of 11,4 mm or more, but not more than 11,8 mm

0 %

p/st

31.12.2022

*ex 8505 11 00

50

Bars specifically shaped, intended to become permanent magnets after magnetisation, containing neodymium, iron and boron, with dimensions:

a length of 15 mm or more but not more than 52 mm,

a width of 5 mm or more but not more than 42 mm,

of a kind to be used in the manufacture of electric servomotors for industrial automation

0 %

p/st

31.12.2022

*ex 8505 11 00

60

Rings, tubes, bushings or collars made from an alloy of neodymium, iron and boron, with

a diameter of not more than 45 mm,

a height of not more than 45 mm,

of a kind used in the manufacture of permanent magnets after magnetisation

0 %

31.12.2022

*ex 8505 19 90

50

Article of agglomerated ferrite in the shape of a rectangular prism to become permanent magnet after magnetisation

whether or not with bevelled edges

of a length of 27 mm or more but not more than 32 mm (± 0,15 mm),

of a width of 8,5 mm or more but not more than 9,5 mm (+ 0,05 mm/– 0,09 mm),

of a thickness of 5,5 mm or more but not more than 5,8 mm (+ 0/– 0,2 mm), and

of a weight of 6,1 g or more but not more than 8,3 g

0 %

31.12.2022

*ex 8507 60 00

25

Rectangular modules for incorporation in lithium-ion rechargeable batteries, with:

a width of 352,5 mm (± 1 mm) or 367,1 mm (±1mm)

a depth of 300 mm (± 2 mm) or 272,6 mm (± 1 mm)

a height of 268,9 mm (± 1,4 mm) or 229,5 mm (± 1mm)

a weight of 45,9 kg or 46,3 kg

a rating of 75 Ah and

a nominal voltage of 60 V

0 %

31.12.2022

*ex 8507 60 00

50

Modules for the assembly of batteries of ion lithium electric accumulators with:

a length of 298 mm or more, but not more than 408 mm,

a width of 33,5 mm or more, but not more than 209 mm,

a height of 138 mm or more, but not more than 228 mm,

a weight of 3,6 kg or more, but not more than 17 kg, and

a power of 458 Wh or more, but not more than 2 158 Wh

0 %

31.12.2022

*ex 8507 60 00

53

Batteries of lithium-ion electric accumulators or rechargeable module:

a length of 1 203 mm or more, but not more than 1 297 mm,

a width of 282 mm or more, but not more than 772 mm,

a height of 792 mm or more, but not more than 839 mm,

a weight of 253 kg or more, but not more than 293 kg,

power of 22 kWh or 26 kWh, and

constituted of 24 or 48 modules

0 %

31.12.2022

*ex 8511 30 00

55

Ignition coil:

with a length of 50 mm or more, but not more than 200 mm,

with an operating temperature of – 40 °C or more, but not more than 140 °C, and

with a voltage of 9 V or more, but not more than 16 V,

with or without connection cable,

for use in the manufacture of engines of motor vehicles (2)

0 %

31.12.2021

*ex 8516 90 00

70

Inner pot:

containing side and central openings,

of annealed aluminium,

with a ceramic coating, heat resistant to more than 200 °C

for use in the manufacture of an electric fryer (2)

0 %

p/st

31.12.2022

*ex 8518 29 95

30

Loudspeakers of:

an impedance of 3 Ohm or more, but not more than 16 Ohm,

a nominal power of 2 W or more, but not more than 20 W,

with or without plastic bracket, and

with or without electric cable fitted with connectors,

of a kind used for TV sets and video monitors manufacture as well as home entertainment systems

0 %

31.12.2022

*ex 8526 91 20

30

Control unit of the emergency call system containing GSM and GPS module, for use in the manufacture of goods of Chapter 87 (2)

0 %

31.12.2019

*ex 8529 90 65

75

Modules comprising at least semiconductor chips for:

the generation of driving signals for pixel addressing, or

driving addressing pixels

0 %

p/st

31.12.2022

*ex 8529 90 92

70

Rectangular fastening and covering frame:

of an aluminium alloy containing silicon and magnesium,

with a length of 500 mm or more but not more than 2 200 mm,

with a width of 300 mm or more but not more than 1 500 mm,

of a kind used for the production of TV sets

0 %

p/st

31.12.2022

*ex 8536 69 90

51

SCART type connectors, built into a plastic or metal housing, with 21 pins in 2 rows, for use in the manufacture of products falling within headings 8521 and 8528  (2)

0 %

p/st

31.12.2022

*ex 8536 69 90

88

Secure Digital (SD), CompactFlash, ‘Smart Card’ and ‘Common interface modules (cards)’ female connectors and interfaces, of a kind used for soldering on printed circuit boards, for connecting electrical apparatus and circuits and switching or protecting electrical circuits with a voltage of not more than 1 000 V

0 %

p/st

31.12.2022

*ex 8536 90 95

40

Rivet contacts

of copper

plated with silver nickel alloy AgNi10 or with silver containing by weight 11,2 % (± 1,0 %) of tin oxide and of indium oxide taken together

with a thickness of the plating of 0,3 mm (– 0/+ 0,015 mm)

whether or not gilded

0 %

p/st

31.12.2020

*ex 8537 10 91

70

Programmable memory controller for a voltage not exceeding 1 000 V, of a kind used for the operation of a combustion motor and/or various actuators working with a combustion motor, comprising at least

a printed circuit with active and passive components,

an aluminium housing, and

multiple connectors

0 %

31.12.2022

*ex 8544 20 00

30

Antenna connecting cable for the transmission of radio (AM/FM) signal and whether or not GPS signal, containing:

a coaxial cable,

two or more connectors, and

3 or more plastic clips for attachment to the dashboard

of a kind used in the manufacture of goods of Chapter 87

0 %

31.12.2021

*ex 8544 30 00

35

Wire harness:

with an operation voltage of 12 V,

wrapped in tape or covered in plastic convoluted tubing,

with 16 or more strands, with all terminals to be tin plated or equipped with connectors,

for use in the manufacture of all-terrain or utility task vehicles (2)

0 %

31.12.2021

*ex 8544 30 00

*ex 8544 42 90

85

65

extension two-core cable with two connectors, containing at least:

a rubber grommet,

a metal attachment bracket

of a kind used to connect vehicle speed sensors in the manufacture of vehicles of Chapter 87

0 %

p/st

31.12.2020

*ex 8548 10 29

10

Spent lithium-ion or nickel metal hydride electric accumulators

0 %

31.12.2018

*ex 8708 40 20

30

Automatic gearbox with a hydraulic torque converter with:

at least eight gears,

an engine torque of 300 Nm or more, and

transverse or longitudinal installation

for use in the manufacture of motor vehicles of heading 8703  (2)

0 %

31.12.2022

*ex 8708 40 20

*ex 8708 40 50

40

30

Gear box assembly with one or two inputs and at least three outputs in cast aluminium housing with overall dimensions (excluding the shafts) of not more than 455 mm (width) × 462 mm (height), 680 mm length, equipped with at least:

one exterior-splined output shaft,

a rotary switch to indicate gear position,

the potential for a differential

for use in the manufacture of all-terrain or utility task vehicles (2)

0 %

31.12.2021

*ex 8708 50 20

*ex 8708 50 99

*ex 8708 99 10

*ex 8708 99 97

40

30

70

80

Single input, dual output gearcase (transmission) in cast aluminium housing, with overall dimensions not exceeding 148 mm (± 1 mm) × 213 mm (± 1 mm) × 273 mm (± 1 mm) comprising at least:

two electro-magnetic one direction clutches in one cage, working in both directions,

an input shaft with outer diameter of 24 mm (± 1 mm), ended with spline of 22,

a coaxial output bushing with inner diameter of 22 mm or more but not more than 30 mm, ended with spline of 22 teeth or more but not more than 28 teeth

for use in the manufacture of all-terrain or utility task vehicles (2)

0 %

31.12.2021

*ex 8708 93 10

*ex 8708 93 90

30

30

Mechanically operated centrifugal clutch for use with an elastomeric belt in a dry environment in a continuously variable transmission (CVT), equipped with:

elements that activate the clutch at given rotation and generate (in this way) centrifugal force,

shaft ended with 5 or more but not more than 6 degree taper,

3 weights, and

1 compression spring

for use in the manufacture of all-terrain or utility task vehicles (2)

0 %

31.12.2021

*ex 8708 99 97

85

Electroplated interior or exterior parts consisting of:

a copolymer of acrylonitrile-butadiene-styrene (ABS), whether or not mixed with polycarbonate,

layers of copper, nickel and chromium

for use in the manufacturing of parts for motor vehicles of heading 8701 to 8705  (2)

0 %

p/st

31.12.2022

*ex 9001 20 00

10

Material consisting of a polarising film, whether or not on rolls, supported on one or both sides by transparent material, whether or not with an adhesive layer, covered on one side or on both sides with a release film

0 %

31.12.2022

*ex 9001 50 41

*ex 9001 50 49

40

40

Organic uncut corrective eyeglass lens, finished on both sides, to undergo a coating, colouring, edging, mounting or any other substantial process for use in the manufacture of corrective glasses (2)

0 %

31.12.2022

*ex 9001 90 00

25

Unmounted optical elements made from moulded infrared transmitting chalcogenide glass, or a combination of infrared transmitting chalcogenide glass and another lens material

0 %

31.12.2018

*ex 9002 11 00

20

Lenses

measuring not more than 80 mm × 55 mm × 50 mm,

with a resolution of 160 lines/mm or better, and

with a zoom ratio of 18 times,

of a kind used for the production of visualizers or live image cameras

0 %

31.12.2022

*ex 9002 11 00

40

Lenses

measuring not more than 125 mm × 65 mm × 65 mm,

with a resolution of 125 lines/mm or better, and

with a zoom ratio of 16 times

of a kind used for the production of visualizers or live image cameras

0 %

31.12.2018

*ex 9002 11 00

85

Lens assembly with:

a horizontal field of view range of 50 deg or more, but not more than 200 deg,

a focal length of 1,16 mm or more, but not more than 5,45 mm,

a relative aperture of F/2,0 or more but not more than F/2,6, and

a diameter of 5 mm or more but not more than 18,5 mm,

for use in the manufacture of CMOS automotive cameras (2)

0 %

31.12.2019

*ex 9002 90 00

40

Mounted lenses made from infrared transmitting chalcogenide glass, or a combination of infrared transmitting chalcogenide glass and another lens material

0 %

p/st

31.12.2022

*ex 9032 89 00

40

Digital valve controller for controlling liquids and gases

0 %

p/st

31.12.2022


(2)  Suspension of duties is subject to end-use customs supervision in accordance with Article 254 of Regulation (EU) No 952/2013 of the European Parliament and of the Council of 9 October 2013 laying down the Union Customs Code (OJ L 269, 10.10.2013, p. 1).

(3)  Only the ad valorem duty is suspended. The specific duty shall continue to apply.

(4)  A surveillance of imports of goods covered by this tariff suspension shall be established in accordance with the procedure laid down in Articles 55 and 56 of Commission Implementing Regulation (EU) 2015/2447 of 24 November 2015 laying down detailed rules for implementing certain provisions of Regulation (EU) No 952/2013 of the European Parliament and of the Council laying down the Union Customs Code (OJ L 343, 29.12.2015, p. 558).

*

A newly introduced measure or a measure with amended conditions.


30.12.2017   

EN

Official Journal of the European Union

L 351/55


COMMISSION IMPLEMENTING REGULATION (EU) 2017/2468

of 20 December 2017

laying down administrative and scientific requirements concerning traditional foods from third countries in accordance with Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods

(Text with EEA relevance)

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Regulation (EU) 2015/2283 of the European Parliament and of the Council of 25 November 2015 on novel foods, amending Regulation (EU) No 1169/2011 of the European Parliament and of the Council and repealing Regulation (EC) No 258/97 of the European Parliament and of the Council and Commission Regulation (EC) No 1852/2001 (1), and in particular Article 20 and Article 35(3) thereof,

Whereas:

(1)

Regulation (EU) 2015/2283 lays down rules for the placing on the market and use of novel foods in the Union.

(2)

Pursuant to Article 20 of Regulation (EU) 2015/2283 the Commission has to adopt implementing acts laying down administrative and scientific requirements concerning traditional foods from third countries.

(3)

Without prejudice to Articles 5, 15 and 16 of Regulation (EU) 2015/2283, the Commission should verify whether the notification falls within the scope of that Regulation and the validity of the notification or the application.

(4)

Notifications referred to in Article 14 of Regulation (EU) 2015/2283 should contain sufficient information and scientific documentation to allow the Commission to verify the validity and enable Member States and the Authority to evaluate the history of safe use of the traditional food from a third country.

(5)

Applications referred to in Article 16 of Regulation (EU) 2015/2283 should contain sufficient information and scientific documentation to allow the Commission to verify the validity and enable the Authority to conduct comprehensive risk assessments.

(6)

Where the applicant submits a notification or an application to add, remove or change the conditions of use, the specifications, additional specific labelling requirements or post-market monitoring requirements of an authorised traditional food from a third country, it may not be necessary for the applicant to provide all the data required for the safety assessment where the applicant provides adequate verifiable justification.

(7)

The exchange of information between the Commission, the Member States and the Authority should allow that duly reasoned safety objections are submitted to the Commission where necessary.

(8)

The opinion of the Authority should provide sufficient information to ascertain whether the proposed use of the traditional food from a third country is safe for consumers.

(9)

Pursuant to Article 35(3) of Regulation (EU) 2015/2283 the Commission has to adopt implementing acts laying down the requirements referred to in Article 20 of that Regulation.

(10)

The measures provided for in this Regulation are in accordance with the opinion of the Standing Committee on Plants, Animals, Food and Feed,

HAS ADOPTED THIS REGULATION:

Article 1

Scope and subject matter

This Regulation lays down rules for the implementation of Article 20 of Regulation (EU) 2015/2283 as regards the administrative and scientific requirements concerning traditional foods from third countries and transitional measures referred to in Article 35(3) of that Regulation.

It applies to notifications and applications as referred to in Articles 14 and 16 of Regulation (EU) 2015/2283.

Article 2

Definitions

In addition to the definitions laid down in Articles 2 and 3 of Regulation (EC) No 178/2002 of the European Parliament and of the Council (2) and Regulation (EU) 2015/2283, the following definitions shall apply:

(a)

‘notification’ means a stand-alone dossier containing the information and the scientific data submitted in accordance with Article 14 of Regulation (EU) 2015/2283.

(b)

‘application’ means a stand-alone dossier containing the information and the scientific data submitted in accordance with Article 16 of Regulation (EU) 2015/2283.

Article 3

Structure, content and presentation of a notification

1.   A notification shall be submitted electronically to the Commission and shall consist of the following:

(a)

a cover letter;

(b)

a technical dossier;

(c)

a summary of the dossier.

2.   The cover letter referred to in paragraph 1(a) shall be drafted in accordance with the template provided in Annex I.

3.   The technical dossier referred to in paragraph 1(b) shall contain:

(a)

the administrative data as provided for in Article 5;

(b)

the scientific data as provided for in Article 6.

4.   Where the applicant submits a notification to modify the conditions of use, the specifications, specific labelling requirements or post-market monitoring requirements of an authorised traditional food from a third country, it may not be necessary for the applicant to provide all the data required under Article 6 where the applicant provides verifiable justification explaining that the proposed changes do not affect the results of the existing safety assessment.

5.   The summary of the dossier referred to in paragraph 1(c) shall provide evidence that the use of a traditional food from a third country complies with the conditions laid down in Article 7 of Regulation (EU) 2015/2283.

Article 4

Structure, content and presentation of an application

1.   An application shall be submitted electronically to the Commission and shall consist of the following:

(a)

a cover letter;

(b)

a technical dossier;

(c)

a summary of the dossier;

(d)

duly reasoned safety objections referred to in Article 15(2) of Regulation (EU) 2015/2283;

(e)

the applicant's response to duly reasoned safety objections.

2.   The cover letter referred to in paragraph 1(a) shall be drafted in accordance with the template provided in Annex II.

3.   The technical dossier referred to in paragraph 1(b) shall contain:

(a)

the administrative data as provided for in Article 5;

(b)

the scientific data as provided for in Article 6.

4.   Where the applicant submits an application to modify the conditions of use, the specifications, specific labelling requirements or post-market monitoring requirements of an authorised traditional food from a third country, it may not be necessary for the applicant to provide all the data required under Article 6 where the applicant provides verifiable justification explaining that the proposed changes not affect the results of the existing safety assessment.

5.   The summary of the dossier referred to in paragraph 1(c) shall provide evidence that the use of a traditional food from a third country complies with the conditions laid down in Article 7 of Regulation (EU) 2015/2283.

Article 5

Administrative data to be provided in a notification or an application

In addition to the information set out in Article 14 of Regulation (EU) 2015/2283, the notifications and the applications shall include the following administrative data:

(a)

the name, address and contact details of the person responsible for the dossier authorised to communicate on behalf of the applicant with the Commission;

(b)

the date of submission of the dossier;

(c)

a table of contents of the dossier;

(d)

a detailed list of documents annexed to the dossier, including references to titles, volumes and pages;

(e)

a list of the parts of the dossier to be treated as confidential in accordance with Article 23 of Regulation (EU) 2015/2283 and the rules set out in Annex III to this Regulation.

Article 6

Scientific data to be provided in a notification or an application

1.   The dossier submitted in support of a notification or an application for the authorisation of a traditional food from a third country shall enable a history of safe use of the traditional food from a third country to be assessed.

2.   The applicant shall provide a copy of the documentation on the procedure followed when gathering the data.

3.   The applicant shall provide a description of the safety evaluation strategy and shall justify the inclusion and exclusion of specific studies or information.

4.   The applicant shall propose an overall conclusion on the safety of the proposed uses of the traditional food from a third country. The overall evaluation of potential risk to human health shall be made in the context of known or likely human exposure.

Article 7

Verification of the validity of a notification

1.   On receipt of a notification of a traditional food from a third country, the Commission shall without delay verify whether the food concerned falls within the scope of Regulation (EU) 2015/2283 and whether the notification fulfils the requirements set out in Articles 3, 5 and 6 of this Regulation.

2.   The Commission may request additional information from the applicant as regards the validity of the notification and inform the applicant of the period within which that information shall be provided.

3.   By way of derogation from paragraph 1 of this Article and without prejudice to Article 14 of Regulation (EU) 2015/2283, a notification may be considered valid even if it does not contain all the elements required under Articles 3, 5 and 6 of this Regulation, provided that the applicant has submitted verifiable justification for each missing element.

4.   The Commission shall inform the applicant, the Member States and the Authority of the reasons why the notification is considered not valid.

Article 8

Verification of the validity of an application

1.   On receipt of an application for the authorisation of a traditional food from a third country the Commission shall without delay verify whether the application fulfils the requirements of Articles 4 to 6.

2.   The Commission may request additional information from the applicant on matters regarding the validity of the application and inform the applicant of the period within which that information shall be provided.

3.   By way of derogation from paragraph 1 of this Article and without prejudice to Article 16 of Regulation (EU) 2015/2283, an application may be considered valid even if it does not contain all the elements required under Articles 4 to 6 of this Regulation, provided that the applicant has submitted verifiable justification for each missing element.

4.   The Commission shall inform the applicant, the Member States and the Authority whether the application is considered valid or not. If the application is not considered valid, the Commission shall indicate the reasons why it is not valid.

Article 9

Duly reasoned safety objections

1.   On receipt of a valid notification, consultation between the Commission, the Member States and the Authority may be carried out in the first three months of the period established in Article 15(2) of Regulation (EU) 2015/2283.

2.   The duly reasoned safety objections submitted by a Member State or the Authority to the Commission in accordance with Article 15(2) of Regulation (EU) 2015/2283 shall include the following information:

(a)

the name and description of the traditional food from a third country;

(b)

a scientific statement indicating why the traditional food from a third country may pose a safety risk to human health.

Article 10

Information to be included in the opinion of the Authority

1.   The opinion of the Authority shall include the following information:

(a)

the identity and characterisation of the traditional food from a third country;

(b)

the assessment of the history of safe use in a third country;

(c)

an overall risk assessment establishing if possible the safety of the traditional food from a third country and highlighting uncertainties and limitations where relevant;

(d)

conclusions.

2.   The Commission may ask for additional information in its request for an opinion of the Authority.

Article 11

Transitional measures

The notifications as referred to in Article 35(2) of Regulation (EU) 2015/2283 shall be submitted to the Commission not later than 1 January 2019.

Article 12

Entry into force and application

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 20 December 2017.

For the Commission

The President

Jean-Claude JUNCKER


(1)  OJ L 327, 11.12.2015, p. 1.

(2)  Regulation (EC) No 178/2002 of the European Parliament and of the Council of 28 January 2002 laying down the general principles and requirements of food law, establishing the European Food Safety Authority and laying down procedures in matters of food safety (OJ L 31, 1.2.2002, p. 1).


ANNEX I

Template cover letter accompanying a notification for traditional food from a third country following the requirements of Article 14 of Regulation (EU) 2015/2283

EUROPEAN COMMISSION

Directorate General

Directorate

Unit

Date: …

Subject: Notification for authorisation of a traditional food from a third country in accordance with Regulation (EU) 2015/2283.

(Please indicate clearly by ticking one of the boxes)

Notification for an authorisation of a new traditional food.

Notification for adding, removing or changing the conditions of use of an already authorised traditional food. Please provide a reference to that notification.

Notification for adding, removing or changing the specifications of an already authorised traditional food. Please provide a reference to that notification.

Notification for adding, removing or changing additional specific labelling requirements of an already authorised traditional food. Please provide a reference to that notification.

Notification for adding, removing or changing the post-market monitoring requirements of an already authorised traditional food. Please provide a reference to that notification.

The Applicant(s) or their Representative(s) in the Union

(name(s), address(es)…)

submit(s) this notification in order to update the Union list on novel foods.

Identity of the traditional food:

Confidentiality (1). Where appropriate, state whether the application includes confidential data in accordance with Article 23 of Regulation (EU) 2015/2283

Yes

No

Food categories, conditions of use and labelling requirements

Food category

Specific conditions of use

Additional specific labelling requirement

 

 

 

 

 

Yours sincerely,

Signature …

Enclosures:

Complete technical dossier

Summary of the dossier

List of the parts of the dossier requested to be treated as confidential and verifiable justification for such claims

Copy of administrative data of applicant(s)


(1)  Applicants should use the format established in Annex III to indicate which information they wish to have treated as confidential and should provide all necessary details to substantiate the request for confidentiality.


ANNEX II

Template cover letter accompanying an application for traditional food from a third country following the requirements of Article 16 of Regulation (EU) 2015/2283

EUROPEAN COMMISSION

Directorate General

Directorate

Unit

Date: …

Subject: Application for authorisation of a traditional food from a third country following the requirements of Article 16 of Regulation (EU) 2015/2283

The Applicant(s) or their Representative(s) within the European Union

(name(s), address(es)…)

submit(s) this application in order to update the Union list on novel foods.

Identity of the traditional food:

Confidentiality (1). Where appropriate, state whether the application includes confidential data in accordance with Article 23 of Regulation (EU) 2015/2283

Yes

No

Food categories, conditions of use and labelling requirements

Food category

Specific conditions of use

Additional specific labelling requirement

 

 

 

 

 

 

Yours sincerely,

Signature …

Enclosures:

Complete application

Summary of the application

List of the parts of the application requested to be treated as confidential and verifiable justification for such claims

Documented data relating to the duly reasoned safety objections

Copy of administrative data of applicant(s)


(1)  Applicants should use the format established in Annex III to indicate the information they wish to have treated as confidential and should provide all necessary details to substantiate the request for confidentiality.


ANNEX III

Justification for confidential information

This Annex shall be updated during the notification or application procedure each time an applicant submits a request for information to be treated as confidential.

Where the production process contains confidential data, a non-confidential summary of the production process shall be provided.

Information requested to be considered as confidential

Justification

Section x.y (submitted on YYYY/MM/DD)

 

 

 

Annex X (submitted on YYYY/MM/DD)

 

 

 

Section x.y. (submitted on YYYY/MM/DD)

 

 

 

Annex X (submitted on YYYY/MM/DD)

 


30.12.2017   

EN

Official Journal of the European Union

L 351/64


COMMISSION IMPLEMENTING REGULATION (EU) 2017/2469

of 20 December 2017

laying down administrative and scientific requirements for applications referred to in Article 10 of Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods

(Text with EEA relevance)

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Regulation (EU) 2015/2283 of the European Parliament and of the Council of 25 November 2015 on novel foods, amending Regulation (EU) No 1169/2011 of the European Parliament and of the Council and repealing Regulation (EC) No 258/97 of the European Parliament and of the Council and Commission Regulation (EC) No 1852/2001 (1), and in particular Article 13 and Article 35(3) thereof,

Whereas:

(1)

Regulation (EU) 2015/2283 lays down rules for the placing on the market and use of novel foods in the Union.

(2)

Pursuant to Article 13 of Regulation (EU) 2015/2283, the Commission has to adopt implementing acts laying down administrative and scientific data requirements for applications referred to in Article 10(1) of that Regulation.

(3)

Without prejudice to Articles 5 and 10 of Regulation (EU) 2015/2283, the Commission should verify whether the application falls within the scope of that Regulation and its validity.

(4)

Applications referred to in Article 10(1) of Regulation (EU) 2015/2283 should contain sufficient information and scientific documentation to allow the Commission to verify their validity and enable the European Food Safety Authority (the Authority) to conduct comprehensive risk assessments of the novel foods.

(5)

The applications should include detailed descriptions of the safety evaluation strategy, the raw data, information on the relevance of the test material used in the toxicological studies, and detection and characterisation test methods for the engineered nanomaterials.

(6)

Experience has shown that in certain cases a novel food intended for a particular group of the population may also reasonably be expected to be consumed by other groups of the population and that risk management measures may be necessary to mitigate potential health risks to those other population groups. Therefore, sufficient information should be provided in the application to enable the risks to those population groups to be assessed.

(7)

Where the applicant submits an application to add, remove or change the conditions of use, the specifications, additional specific labelling requirements or post-market monitoring requirements of an authorised novel food, it may not be necessary for the applicant to provide all the data required for the risk assessment, where the applicant provides verifiable justification.

(8)

In order to ensure that toxicological tests are performed to a certain standard, they should be carried out in accordance with the rules set out in Directive 2004/10/EC of the European Parliament and of the Council (2). Where those tests are carried out outside the territory of the Union, they should follow the OECD Principles of Good Laboratory Practice (3).

(9)

The opinion of the Authority should provide sufficient information to ascertain whether the proposed use of the novel food is safe for consumers.

(10)

In order to benefit from data protection, as laid down in Article 26 of Regulation (EU) 2015/2283, requests for protection of proprietary data should be justified and all data concerned should be kept in a separate part of the application.

(11)

Pursuant to Article 35 of Regulation (EU) 2015/2283, it is necessary to lay down transitional measures for the entry into force of that Regulation.

(12)

The measures provided for in this Regulation are in accordance with the opinion of the Standing Committee on Plants, Animals, Food and Feed,

HAS ADOPTED THIS REGULATION:

Article 1

Scope and subject matter

This Regulation lays down rules for the implementation of Article 13 of Regulation (EU) 2015/2283 as regards the administrative and scientific requirements for applications referred to in Article 10(1) and the transitional measures referred to in Article 35(3) of that Regulation.

Article 2

Definitions

In addition to the definitions laid down in Articles 2 and 3 of Regulation (EC) No 178/2002 of the European Parliament and of the Council (4) and Regulation (EU) 2015/2283, the following definition shall apply:

 

‘application’ means a stand-alone dossier containing the information and the scientific data submitted for the authorisation of a novel food pursuant to Article 10(1) of Regulation (EU) 2015/2283.

Article 3

Structure, content and presentation of an application

1.   An application shall be submitted electronically to the Commission and shall consist of the following:

(a)

a cover letter;

(b)

a technical dossier;

(c)

a summary of the dossier.

2.   The cover letter referred to in paragraph 1(a) shall be drafted in accordance with the template provided in Annex I.

3.   The technical dossier referred to in paragraph 1(b) shall contain:

(a)

the administrative data as provided for in Article 4;

(b)

the scientific data as provided for in Article 5.

4.   Where the applicant submits an application to modify the conditions of use, the specifications, additional specific labelling requirements or post-market monitoring requirements of an authorised novel food, it may not be necessary for the applicant to provide all the data required under Article 5 of this Regulation where the applicant provides verifiable justification explaining that the proposed changes do not affect the results of the existing risk assessment.

5.   In addition to the information referred to in points (a), (b) and (e) of Article 10(2) of Regulation (EU) 2015/2283, the summary of the dossier referred to in paragraph 1(c) of this Article shall set out the reasons why the use of the novel food complies with the conditions laid down in Article 7 of Regulation (EU) 2015/2283.

Article 4

Administrative data requirements

In addition to the information set out in Article 10(2) of Regulation (EU) 2015/2283, the application shall include the following administrative data:

(a)

the name(s) of the manufacturer(s) of the novel food, if different than the applicant's, address and contact details;

(b)

the name, address and contact details of the person responsible for the dossier authorised to communicate on behalf of the applicant with the Commission;

(c)

the date of submission of the dossier;

(d)

a table of contents of the dossier;

(e)

a detailed list of documents annexed to the dossier, including references to titles, volumes and pages;

(f)

a list of the parts of the dossier to be treated as confidential and verifiable justification in accordance with Article 23 of Regulation (EU) 2015/2283 and the rules set out in Annex II to this Regulation. Where the production process contains confidential data, a non-confidential summary of the production process shall be provided;

(g)

information and explanations substantiating the existence of the applicant's right of reference to the proprietary scientific evidence or scientific data in accordance with Article 26 of Regulation (EU) 2015/2283. That information shall be included in a separate folder.

Article 5

Scientific data requirements

1.   The dossier submitted in support of an application for the authorisation of a novel food shall enable a comprehensive risk assessment of the novel food.

2.   Where the application for the authorisation of a novel food involves the use of engineered nanomaterials as referred to in points (a) (viii) and (ix) of Article 3(2) of Regulation (EU) 2015/2283, the applicant shall provide detection and characterisation test methods in compliance with the requirements of Article 10(4) of that Regulation.

3.   The applicant shall provide a copy of the documentation on the procedure and strategy followed when gathering the data.

4.   The applicant shall provide a description of the safety evaluation strategy and the corresponding toxicological testing strategy and shall justify the inclusion or exclusion of specific studies or information.

5.   The applicant shall provide on request the raw data for the individual studies, published and unpublished, undertaken by the applicant, or on their behalf, to support their application. This information includes data used to generate the conclusions of the individual studies and results of examinations.

6.   Where it cannot be excluded that a novel food intended for a particular group of the population would be also consumed by other groups of the population the safety data provided shall also cover those groups.

7.   For each biological or toxicological study, the applicant shall clarify whether the test material conforms to the proposed or existing specification. Where the test material differs from that specification, the applicant shall demonstrate the relevance of those data to the novel food under consideration.

Toxicological studies shall be conducted in facilities which comply with the requirements of Directive 2004/10/EC or, if they are carried out outside the territory of the Union, they shall follow the OECD Principles of Good Laboratory Practice. The applicant shall provide evidence of compliance with those requirements and shall justify any deviation from the standard protocols.

8.   The applicant shall propose an overall conclusion on the safety of the proposed uses of the novel food. The overall evaluation of potential risk to human health shall be made in the context of known or likely human exposure.

Article 6

Verification of the validity of an application

1.   On receipt of an application the Commission shall without delay verify whether the application falls within the scope of Regulation (EU) 2015/2283 and whether the application fulfils the requirements set out in Article 10(2) of that Regulation.

2.   The Commission may consult the Authority. The Authority shall provide the Commission with its views on whether the application fulfils the relevant requirements set out in Article 10(2) of Regulation (EU) 2015/2283 within a period of 30 working days.

3.   The Commission may request additional information from the applicant as regards the validity of the application and agree with the applicant of the period within which that information shall be provided.

4.   By way of derogation from paragraph 1 of this Article, and without prejudice to Article 10(2) of Regulation (EU) 2015/2283, an application may be considered as valid even if it does not contain all the elements required under Articles 3 to 5 of this Regulation, provided that the applicant has submitted appropriate justification for each missing element.

5.   The Commission shall inform the applicant, the Member States and the Authority whether the application is considered valid or not. If the application is not considered valid, the Commission shall indicate the reasons why it is not valid.

Article 7

Information to be included in the opinion of the Authority

1.   The opinion of the Authority shall include the following information:

(a)

the identity of the novel food;

(b)

the assessment of the production process;

(c)

compositional data;

(d)

specifications;

(e)

the history of use of the novel food and/or its source;

(f)

the proposed uses and use levels and anticipated intake;

(g)

absorption, distribution, metabolism and excretion (ADME);

(h)

nutritional information;

(i)

toxicological information;

(j)

allergenicity;

(k)

an overall risk assessment for the novel food under the proposed uses and use levels and highlighting uncertainties and limitations where relevant;

(l)

when the dietary exposure exceeds the health-based guidance value identified in the overall risk assessment, the dietary exposure assessment of the novel food shall be detailed, providing the contribution to the total exposure of each food category or foodstuff for which the use is authorised or has been requested;

(m)

conclusions.

2.   The Commission may ask for additional information in its request for an opinion of the Authority.

Article 8

Transitional measures

1.   By 1 January 2018 the Member States shall notify to the Commission the lists of requests referred to in Article 35(1) of Regulation (EU) 2015/2283.

2.   The Members States shall make available all the information they have received on each request referred to in paragraph 1 to the Commission.

3.   Any request referred to in paragraph 1 of this Article shall be updated by the applicant in order to comply with the requirements set out in Article 10(2) of Regulation (EU) 2015/2283 and in this Regulation.

4.   By way of derogation, paragraphs 1 and 2 shall not apply to requests referred to in paragraph 1 of this Article for which an initial assessment report has been forwarded to the Commission pursuant to Article 6(4) of Regulation (EC) No 258/97 of the European Parliament and of the Council (5) by 1 January 2018, and for which no reasoned objections have been made to the marketing of the novel food concerned within the period established in Article 6(4) of that Regulation.

5.   The deadline for the submission of the applications referred to in Article 35(2) of Regulation (EU) 2015/2283 shall be 1 January 2019.

Article 9

Entry into force and application

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 20 December 2017.

For the Commission

The President

Jean-Claude JUNCKER


(1)  OJ L 327, 11.12.2015, p. 1.

(2)  Directive 2004/10/EC of the European Parliament and of the Council of 11 February 2004 on the harmonisation of laws, regulations and administrative provisions relating to the application of the principles of good laboratory practice and the verification of their applications for tests on chemical substances (OJ L 50, 20.2.2004, p. 44).

(3)  OECD Series on Principles of Good Laboratory Practice and Compliance Monitoring. Number 1. OECD Principles on Good Laboratory Practice (as revised in 1997) ENV/MC/CHEM(98)17.

(4)  Regulation (EC) No 178/2002 of the European Parliament and of the Council of 28 January 2002 laying down the general principles and requirements of food law, establishing the European Food Safety Authority and laying down procedures in matters of food safety (OJ L 31, 1.2.2002, p. 1).

(5)  Regulation (EC) No 258/97 of the European Parliament and of the Council of 27 January 1997 concerning novel foods and novel food ingredients (OJ L 43, 14.2.1997, p. 1).


ANNEX I

Template cover letter accompanying an application for novel food

EUROPEAN COMMISSION

Directorate General

Directorate

Unit

Date: …

Subject: Application for authorisation of a novel food in accordance with Regulation (EU) 2015/2283.

(Please indicate clearly by ticking one of the boxes)

Application for an authorisation of a new novel food.

Application for adding, removing or changing the conditions of use of an already authorised novel food. Please provide a reference to that authorisation.

Application for adding, removing or changing the specifications of an already authorised novel food. Please provide a reference to that authorisation.

Application for adding, removing or changing additional specific labelling requirements of an already authorised novel food. Please provide a reference to that authorisation.

Application for adding, removing or changing post market monitoring requirements of an already authorised novel food. Please provide a reference to that authorisation.

The Applicant(s) or their Representative(s) in the Union

(name(s), address(es)…)

submit(s) this application in order to update the Union list on novel foods.

Identity of the novel food (information on the identity of the novel food should be provided, depending on the category(ies) under which the novel food falls):

Confidentiality (1). Where appropriate, state whether the application includes confidential data in accordance with Article 23 of Regulation (EU) 2015/2283

Yes

No

Data Protection (2). Where appropriate, state whether the application includes a request for the protection of proprietary data according to Article 26 of Regulation (EU) 2015/2283:

Yes

No

Food categories, conditions of use and labelling requirements

Food category

Specific conditions of use

Additional specific labelling requirement

 

 

 

 

 

 

Yours sincerely,

Signature …

Enclosures:

Complete dossier

Summary of the dossier

List of the parts of the dossier requested to be treated as confidential and verifiable justification for such claims

Information supporting the protection of proprietary data relating to the novel food application

Copy of administrative data of applicant(s)


(1)  Applicants should use the format established in Annex II to indicate which information they wish to have treated as confidential and should provide all necessary details to substantiate the request for confidentiality.

(2)  Applicant should specify the part(s) of the application which include(s) proprietary data for which protection is requested, clearly stating section(s) and page number(s). Applicant should provide verifiable justification /declaration for the proprietary claim.


ANNEX II

Justification for confidential information

This Annex shall be updated during the application procedure each time an applicant submits a request for information to be treated as confidential.

Where the production process contains confidential data, a non-confidential summary of the production process shall be provided.

Information requested to be considered as confidential

Justification

Section x.y (submitted on YYYY/MM/DD)

 

 

 

Annex X (submitted on YYYY/MM/DD)

 

 

 

Section x.y (submitted on YYYY/MM/DD)

 

 

 

Annex X (submitted on YYYY/MM/DD)

 


30.12.2017   

EN

Official Journal of the European Union

L 351/72


COMMISSION IMPLEMENTING REGULATION (EU) 2017/2470

of 20 December 2017

establishing the Union list of novel foods in accordance with Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods

(Text with EEA relevance)

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Regulation (EU) 2015/2283 of the European Parliament and of the Council on novel foods, amending Regulation (EU) No 1169/2011 of the European Parliament and of the Council and repealing Regulation (EC) No 258/97 of the European Parliament and of the Council and Commission Regulation (EC) No 1852/2001 (1), and in particular Article 8 thereof,

Whereas:

(1)

Regulation (EU) 2015/2283 lays down rules for the placing on the market and use of novel foods within the Union.

(2)

Pursuant to Article 8 of Regulation (EU) 2015/2283, the Commission has to establish the Union list of novel foods authorised or notified under Regulation (EC) No 258/97 of the European Parliament and of the Council (2).

(3)

The Union list of novel foods is to apply without prejudice to other provisions laid down in sector specific legislation.

(4)

The measures provided for in this Regulation are in accordance with the opinion of the Standing Committee on Plants, Animals, Food and Feed,

HAS ADOPTED THIS REGULATION:

Article 1

Union list of authorised novel foods

The Union list of novel foods authorised to be placed on the market within the Union as referred to in Article 6(1) of Regulation (EU) 2015/2283 is hereby established and set out in the Annex to this Regulation.

Article 2

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 20 December 2017.

For the Commission

The President

Jean-Claude JUNCKER


(1)  OJ L 327, 11.12.2015, p. 1.

(2)  Regulation (EC) No 258/97 of the European Parliament and of the Council of 27 January 1997 concerning novel foods and novel food ingredients (OJ L 43, 14.2.1997, p. 1).


ANNEX

UNION LIST OF NOVEL FOODS

Content of the list

1.

The Union list shall consist of Tables 1 and 2.

2.

Table 1 includes the authorised novel foods and contains the following information:

Column 1

:

Authorised novel food

Column 2

:

Conditions under which the novel food may be used. This column is further subdivided into two: Specified food category and Maximum levels

Column 3

:

Additional specific labelling requirements

Column 4

:

Other requirements

3.

Table 2 includes the specifications on novel foods and contains the following information:

Column 1

:

Authorised novel food

Column 2

:

Specifications

Table 1: Authorised novel foods

Authorised novel food

Conditions under which the novel food may be used

Additional specific labelling requirements

Other requirements

N-Acetyl-D-neuraminic acid

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘N-acetyl-D-neuraminic acid’

Food supplements containing N-acetyl-D-neuraminic acid shall bear a statement that the food supplement should not be given to infants, young children and children under 10 years of age where they consume breast milk or other foods with added N-acetyl-D-neuraminic acid within the same twenty four hour period.

 

Infant and follow-on formulae as defined by Regulation (EU) No 609/2013 (1)

0,05 g/L of reconstituted formula

Processed cereal-based foods and baby foods for infants and young children as defined by Regulation (EU) No 609/2013

0,05 g/kg for solid foods

Foods for special medical purposes for infants and young children as defined by Regulation (EU) No 609/2013

In accordance with the particular nutritional requirements of the infants and young children for whom the products are intended but in any case not higher than the maximum levels specified for the category mentioned in the table corresponding to the products.

Total diet replacement foods for weight control as defined by Regulation (EU) No 609/2013

0,2 g/L (drinks)

1,7 g/kg (bars)

Foods bearing statements on the absence or reduced presence of gluten in accordance with the requirements of Commission Implementing Regulation (EU) No 828/2014 (2)

1,25 g/kg

Unflavoured pasteurised and sterilised (including UHT) milk-based products

0,05 g/L

Unflavoured fermented milk-based products, heat treated after fermentation, flavoured fermented milk products including heat-treated products

0,05 g/L (beverages)

0,4 g/kg (solids)

Dairy analogues, including beverage whiteners

0,05 g/L (beverages)

0,25 g/kg (solids)

Cereal bars

0,5 g/kg

Table top sweeteners

8,3 g/kg

Fruit and vegetable-based drinks

0,05 g/L

Flavoured drinks

0,05 g/L

Speciality coffee, tea, herbal and fruit infusions, chicory; tea, herbal and fruit infusions and chicory extracts; tea, plant, fruit and cereal preparations for infusions

0,2 g/kg

Food Supplements as defined in Directive 2002/46/EC (3)

300 mg/day for general population older than 10 years

55 mg/day for infants

130 mg/day for young children

250 mg/day for children between 3 to 10 years of age

Adansonia digitata (Baobab) dried fruit pulp

Not specified

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Baobab fruit pulp’

 

Ajuga reptans extract from cell cultures

Specified food category

Maximum levels

 

 

Food Supplements as defined in Directive 2002/46/EC

In line with normal use in food supplements of a similar extract of the flowering aerial parts of Ajuga reptans

L-Alanyl-L-Glutamine

Specified food category

Maximum levels

 

 

Food Supplements as defined in Directive 2002/46/EC

 

Foods for special medical purposes as defined in Regulation (EU) No 609/2013 excluding foods for infants and young children

Algal oil from the microalgae Ulkenia sp.

Specified food category

Maximum levels of DHA

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Oil from the micro-algae Ulkenia sp.

 

Bakery products (breads, rolls and sweet biscuits)

200 mg/100 g

Cereal bars

500 mg/100 g

Non-alcoholic beverages (including milk based beverages)

60 mg/100 ml

Allanblackia seed oil

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Allanblackia seed oil’

 

Yellow fat spreads and cream based spreads

20 g/100 g

Aloe macroclada Baker leaf extract

Specified food category

Maximum levels

 

 

Food Supplements as defined in Directive 2002/46/EC

In line with normal use in food supplements of the similar gel derived from Aloe vera (L.) Burm.

Antarctic Krill oil from Euphausia superba

Specified food category

Maximum levels of combined DHA and EPA

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Lipid extract from the crustacean Antarctic Krill (Euphausia superba)’

 

Dairy products except milk-based drinks

200 mg/100 g or for cheese products 600 mg/100 g

Dairy analogues except drinks

200 mg/100 g or for analogues to cheese products 600 mg/100 g

Non-alcoholic beverages

Milk-based drinks

Dairy analogue drinks

80 mg/100 ml

Spreadable fat and dressings

600 mg/100 g

Cooking fats

360 mg/100 ml

Breakfast cereals

500 mg/100 g

Bakery products (breads, rolls and sweet biscuits)

200 mg/100 g

Nutrition bars/cereal bars

500 mg/100 g

Food Supplements as defined in Directive 2002/46/EC

3 000 mg/day for the general population

450 mg/day for pregnant and lactating women

Foods for special medical purposes as defined in Regulation (EU) No 609/2013

In accordance with the particular nutritional requirements of the persons for whom the products are intended

Total diet replacement for weight control as defined in Regulation (EU) No 609/2013 and meal replacements for weight control

250 mg/meal

Processed cereal-based food and baby food intended for infants and young children covered by Regulation (EU) No 609/2013

200 mg/100 ml

Foods intended to meet the expenditure of intense muscular effort, especially for sportsmen

Foods bearing statements on the absence or reduced presence of gluten in accordance with the requirements of Commission Implementing Regulation (EU) No 828/2014

Antarctic Krill oil rich in phospholipids from Euphausia superba

Specified food category

Maximum levels of combined DHA and EPA

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Lipid extract from the crustacean Antarctic Krill (Euphausia superba)’

 

Dairy products except milk-based drinks

200 mg/100 g or for cheese products 600 mg/100 g

Dairy analogues except drinks

200 mg/100 g or for analogues to cheese products 600 mg/100 g

Non-alcoholic beverages

Milk-based drinks

Dairy analogue drinks

80 mg/100 ml

Spreadable fat and dressings

600 mg/100 g

Cooking fats

360 mg/100 ml

Breakfast cereals

500 mg/100 g

Bakery products (breads, rolls and sweet biscuits)

200 mg/100 g

Nutrition bars/cereal bars

500 mg/100 g

Food Supplements as defined in Directive 2002/46/EC

3 000 mg/day for the general population

450 mg/day for pregnant and lactating women

Foods for special medical purposes as defined in Regulation (EU) No 609/2013

In accordance with the particular nutritional requirements of the persons for whom the products are intended

Total diet replacement for weight control as defined in Regulation (EU) No 609/2013 and meal replacements for weight control

250 mg/meal

Processed cereal-based food and baby food intended for infants and young children covered by Regulation (EU) No 609/2013

200 mg/100 ml

Foods intended to meet the expenditure of intense muscular effort, especially for sportsmen

Foods bearing statements on the absence or reduced presence of gluten in accordance with the requirements of Commission Implementing Regulation (EU) No 828/2014

Arachidonic acid-rich oil from the fungus Mortierella alpina

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Oil from Mortierella alpina’ or ‘Mortierella alpina oil’

 

Infant formula and follow-on formula as defined in Regulation (EU) No 609/2013

In accordance with Regulation (EU) No 609/2013

Foods for special medical purposes for premature infants as defined in Regulation (EU) No 609/2013

In accordance with Regulation (EU) No 609/2013

Argan oil from Argania spinosa

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Argan oil’ and if used as seasoning ‘Vegetable oil only for seasoning’ shall be mentioned on the label

 

As seasonings

Not specified

Food Supplements as defined in Directive 2002/46/EC

In line with normal food use of vegetable oils

Astaxanthin-rich oleoresin from Haematococcus pluvialis algae

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Astaxanthin’

 

Food Supplements as defined in Directive 2002/46/EC

40-80 mg/day of oleoresin, resulting in ≤ 8 mg astaxanthin per day

Basil seeds (Ocimum basilicum)

Specified food category

Maximum levels

 

 

Fruit juice and fruit/vegetable blend beverages

3 g/200 ml for addition of whole basil seeds (Ocimum basilicum)

Fermented black bean extract

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Fermented black bean (Soya) extract’ or ‘Fermented Soya extract’

 

Food Supplements as defined in Directive 2002/46/EC

4,5 g/day

Bovine lactoferrin

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Lactoferrin from cows' milk’

 

Infant formula and follow-on formula as defined in Regulation (EU) No 609/2013 (ready to drink)

100 mg/100 ml

Foods on dairy basis intended for young children (ready to eat/drink)

200 mg/100 g

Processed cereal food (solid)

670 mg/100 g

Foods for special medical purposes as defined in Regulation (EU) No 609/2013

Depending on the needs of the individual up to 3 g/day

Beverages based on milk

200 mg/100 g

Powdered drink mixes based on milk (ready to drink)

330 mg/100 g

Beverages based on fermented milk (including yoghurt drinks)

50 mg/100 g

Non-alcoholic drinks

120 mg/100 g

Products based on yoghurt

80 mg/100 g

Products based on cheese

2 000 mg/100 g

Ice cream

130 mg/100 g

Cakes and pastries

1 000 mg/100 g

Candies

750 mg/100 g

Chewing gum

3 000 mg/100 g

Buglossoides arvensis seed oil

Specified food category

Maximum levels of stearidonic acid (STA)

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Refined Buglossoides oil’

 

Dairy products and analogues

250 mg/100 g

75 mg/100 g for drinks

Cheese and cheese products

750 mg/100 g

Butter and other fat and oil emulsions including spreads (not for cooking or frying purposes)

750 mg/100 g

Breakfast cereals

625 mg/100 g

Food supplements as defined in Directive 2002/46/EC, excluding food supplements for infants and young children

500 mg/day

Foods for special medical purposes as defined in Regulation (EU) No 609/2013, excluding foods for special medical purposes intended for infants and young children

In accordance with the particular nutritional requirements of the persons for whom the products are intended

Total diet replacement for weight control as defined in Regulation (EU) No 609/2013 and meal replacements for weight control

250 mg/meal

Calanus finmarchicus oil

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘oil from Calanus finmarchicus (crustacean)’

 

Food supplements as defined in Directive 2002/46/EC

2,3 g/day

Chewing gum base (monomethoxypolyethylene glycol)

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Gum base (including 1,3-butadiene, 2-methyl-homopolymer, maleated, esters with polyethylene glycol mono-Me ether)’ or ‘Gum base (including CAS No: 1246080-53-4)’

 

Chewing gum

8 %

Chewing gum base (Methyl vinyl ether-maleic anhydride copolymer)

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Gum base (including methyl vinyl ether-maleic anhydride copolymer)’ or ‘Gum base (including CAS No 9011-16-9)’

 

Chewing gum

2 %

Chia oil from Salvia hispanica

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Chia oil (Salvia hispanica)’

 

Fats and oils

10 %

Pure chia oil

2 g/day

Food Supplements as defined in Directive 2002/46/EC

2 g/day

Chia seeds (Salvia hispanica)

Specified food category

Maximum levels

1.

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Chia seeds (Salvia hispanica)’

2.

Pre-packaged Chia (Salvia hispanica) seeds shall carry additional labelling to inform the consumer that the daily intake is no more than 15 g.

 

Bread products

5 % (whole or ground chia seeds)

Baked products

10 % whole chia seeds

Breakfast cereals

10 % whole chia seeds

Fruit, nut and seed mixes

10 % whole chia seeds

Fruit juice and fruit/vegetable blend beverages

15 g/day for addition of whole, mashed or ground chia seeds

Pre-packaged Chia seed as such

15 g/day whole chia seeds

Fruit spreads

1 % whole chia seeds

Yoghurt

1,3 g whole chia seeds per 100 g of yoghurt or 4,3 g whole chia seeds per 330 g of yoghurt (portion)

Sterilised ready to eat meals based on cereal grains, pseudocereals grains and/or pulses

5 % whole chia seeds

Chitin-glucan from Aspergillus niger

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Chitin-glucan from Aspergillus niger

 

Food Supplements as defined in Directive 2002/46/EC

5 g/day

Chitin-glucan complex from Fomes fomentarius

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Chitin-glucan from Fomes fomentarius

 

Food Supplements as defined in Directive 2002/46/EC

5 g/day

Chitosan extract from fungi (Agaricus bisporus; Aspergillus niger)

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Chitosan extract from Agaricus bisporus’ or ‘Chitosan extract from Aspergillus niger

 

Food Supplements as defined in Directive 2002/46/EC

In line with normal use in food supplements of chitosan from crustaceans

Chondroitin sulphate

Specified food category

Maximum levels

The designation of the novel on the labelling of the foodstuff containing it shall be ‘Chondroitin sulphate derived from microbial fermentation and sulphation’

 

Food supplements as defined in Directive 2002/46/EC for adult population, excluding pregnant and lactating women

1 200 mg/day

Chromium Picolinate

Specified food category

Maximum levels of total chromium

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Chromium Picolinate’

 

Foods covered by Regulation (EU) No 609/2013

250 μg/day

Foods fortified in accordance with Regulation (EC) No 1925/2006 (4)

Cistus incanus L. Pandalis herb

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Cistus incanus L. Pandalis herb’

 

Herbal infusions

Intended daily intake: 3 g herbs/day (2 cups/day)

Citicoline

Specified food category

Maximum levels

1.

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Citicoline’

2.

The labelling of foods containing citicoline shall bear a statement that the product is not intended to be consumed by children

 

Food Supplements as defined in Directive 2002/46/EC

500 mg/day

Foods for special medical purposes as defined in Regulation (EU) No 609/2013

250 mg per serving and a maximum daily consumption level of 1 000 mg

Clostridium butyricum

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Clostridium butyricum MIYAIRI 588 (CBM 588)’ or ‘Clostridium butyricum (CBM 588)’

 

Food Supplements as defined in Directive 2002/46/EC

1,35 × 108 CFU/day

Extract of defatted cocoa powder

Specified food category

Maximum levels

Consumers shall be instructed not to consume more than 600 mg polyphenols corresponding to 1,1 g of extract of defatted cocoa powder per day

 

Nutrition bars

1 g/day and 300 mg polyphenols corresponding to not more than 550 mg of extract of defatted cocoa powder in one portion of food (or food supplement)

Milk based beverages

Any other foods (including food supplements as defined in Directive 2002/46/EC) which have become established vehicles for functional ingredients and which are typically positioned for consumption by health conscious adults

Low fat cocoa extract

Specified food category

Maximum levels

Consumers shall be instructed not to consume more than 600 mg of cocoa flavanols per day

 

Foods including food supplements as defined in Directive 2002/46/EC

730 mg per serving and around 1,2 g/day

Coriander seed oil from Coriandrum sativum

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Coriander seed oil’

 

Food Supplements as defined in Directive 2002/46/EC

600 mg/day

Crataegus pinnatifida dried fruit

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Crataegus pinnatifida dried fruit’

 

Herbal infusions

In line with normal food use of Crataegus laevigata

Jams and jellies in accordance with Directive 2001/113/EC (5)

Compotes

α-cyclodextrin

Not specified

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Alpha-cyclodextrin’ or ‘α-cyclodextrin’

 

γ-cyclodextrin

Not specified

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Gamma-Cyclodextrin’ or ‘γ-Cyclodextrin’

 

Dextran preparation produced by Leuconostoc mesenteroides

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Dextran’

 

Bakery products

5 %

Diacylglycerol oil of plant origin

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Diacylglycerol oil of plant origin (at least 80 % diacylglycerols)’

 

Cooking oils

 

Fat spreads

Salad dressings

Mayonnaise

Meal replacement for weight control (as drinks)

Bakery products

Yoghurt type products

Dihydrocapsiate (DHC)

Specified food category

Maximum levels

1.

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Dihydrocapsiate’

2.

Food supplements containing synthetic dihydrocapsiate will be labelled as ‘not intended for children up to 4,5 years’

 

Cereal bars

9 mg/100 g

Biscuits, cookies and crackers

9 mg/100 g

Rice based snacks

12 mg/100 g

Carbonated drinks, dilutable drinks, fruit juice based beverages

1,5 mg/100 ml

Vegetable drinks

2 mg/100 ml

Coffee based drinks, tea based drinks

1,5 mg/100 ml

Flavoured water - still

1 mg/100 ml

Precooked oatmeal cereal

2,5 mg/100 g

Other cereals

4,5 mg/100 g

Ice cream, dairy desserts

4 mg/100 g

Pudding mixes (ready to eat)

2 mg/100 g

Products based on yoghurt

2 mg/100 g

Chocolate confectionery

7,5 mg/100 g

Hard candy

27 mg/100 g

Sugar-free gum

115 mg/100 g

Whitener/creamer

40 mg/100 g

Sweeteners

200 mg/100 g

Soup (ready to eat)

1,1 mg/100 g

Salad dressing

16 mg/100 g

Vegetable protein

5 mg/100 g

Ready to eat meals

3 mg/meal

Meal replacements for weight control

3 mg/meal

Meal replacement for weight control (as drinks)

1 mg/100 ml

Food Supplements as defined in Directive 2002/46/EC

3 mg/single intake

9 mg/day

Non-alcoholic powdered drink mixes

14,5 mg/kg equivalent to 1,5 mg/100 ml

Dried extract of Lippia citriodora from cell cultures

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘dried extract of Lippia citriodora from cell cultures HTN®Vb’

 

Food Supplements as defined in Directive 2002/46/EC

In line with normal use in food supplements of a similar extract from the leaves of Lippia citriodora

Echinacea angustifolia extract from cell cultures

Specified food category

Maximum levels

 

 

Food Supplements as defined in Directive 2002/46/EC

In line with normal use in food supplements of a similar extract from the root of Echinacea angustifolia

Echium plantagineum oil

Specified food category

Maximum levels of stearidonic acid (STA)

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Refined echium oil’

 

Milk-based products and drinkable yoghurt products delivered in a single dose

250 mg/100 g; 75 mg/100 g for drinks

Cheese preparations

750 mg/100 g

Spreadable fat and dressings

750 mg/100 g

Breakfast cereals

625 mg/100 g

Food supplements as defined in Directive 2002/46/EC

500 mg/day

Foods for special medical purposes as defined in Regulation (EU) No 609/2013

In accordance with the particular nutritional requirements of the persons for whom the products are intended

Total diet replacement for weight control as defined in Regulation (EU) No 609/2013 and meal replacements for weight control

250 mg/meal

Epigallocatechin gallate as a purified extract from green tea leaves (Camellia sinensis)

Specified food category

Maximum levels

The labelling shall bear a statement that consumers should not consume more than 300 mg of extract per day

 

Food Supplements as defined in Directive 2002/46/EC

150 mg of extract in one portion of food or food supplement

Foods fortified in accordance with Regulation (EC) No 1925/2006

L-ergothioneine

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘L-ergothioneine’

 

Food supplements as defined in Directive 2002/46/EC

30 mg/day for general population (excluding pregnant and lactating women)

20 mg/day for children older than 3 years

Ferric Sodium EDTA

Specified food category

Maximum levels (expressed as anhydrous EDTA)

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Ferric Sodium EDTA’

 

Food supplements as defined in Directive 2002/46/EC

18 mg/day for children

75 mg/day for adults

Foods covered by Regulation (EU) No 609/2013

12 mg/100 g

Foods fortified in accordance with Regulation (EC) No 1925/2006

Ferrous ammonium phosphate

Specified food category

Maximum levels

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Ferrous ammonium phosphate’

 

Food supplements as defined in Directive 2002/46/EC

To be used in compliance with Directive 2002/46/EC, Regulation (EU) No 609/2013 and/or Regulation (EC) No 1925/2006

Foods covered by Regulation (EU) No 609/2013

Foods fortified in accordance with Regulation (EC) No 1925/2006

Fish peptides from Sardinops sagax

Specified food category

Maximum levels fish peptide product

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Fish (Sardinops sagax) peptides’

 

Foods based on yoghurt, yoghurt drinks, fermented milk products, and powdered milk

0,48 g/100 g (ready to eat/drink)

Flavoured water, and vegetable-based drinks

0,3 g/100 g (ready to drink)

Breakfast cereals

2 g/100 g

Soups, stews and soup powders

0,3 g/100 g (ready to eat)

Flavonoids from Glycyrrhiza glabra

Specified food category

Maximum levels of flavonoids from Glycyrrhiza glabra

1.

The designation of the novel food on the labelling of the foodstuffs containing it shall be ‘Flavonoids from Glycyrrhiza glabra L.

2.

The labelling of the foods where the product was added as a novel food ingredient shall bear a statement that:

(a)

the product should not be consumed by pregnant and breast feeding women, children and young adolescents; and

(b)

people taking prescription drugs should only consume the product under medical supervision;

(c)