(1)

Directive 2010/30/EU requires the Commission to adopt delegated acts as regards the labelling of energy-related products having significant potential for energy savings and a wide disparity in performance levels with equivalent functionality.

(2)

Provisions on the energy labelling of household lamps were established by Commission Directive 98/11/EC (2).

(3)

The electricity used by electrical lamps accounts for a significant share of total electricity demand in the Union. In addition to the energy efficiency improvements already achieved, the scope for further reducing the energy consumption of electrical lamps is substantial.

(4)

Directive 98/11/EC should be repealed and new provisions should be set out in this Regulation in order to ensure that the energy label provides dynamic incentives for suppliers further to improve the energy efficiency of electrical lamps and to speed up the market shift towards energy-efficient technologies. The scope of Directive 98/11/EC is limited to certain technologies within the category of household lamps. In order to use the label to improve the energy efficiency of other lamp technologies, including in professional lighting, this Regulation should also cover directional lamps, extra low voltage lamps, light-emitting diodes, and lamps used predominantly in professional lighting, such as high-intensity discharge lamps.

(5)

Luminaires are often sold with incorporated or accompanying lamps. This Regulation should ensure that consumers are informed about the compatibility of the luminaire with energy-saving lamps and about the energy efficiency of the lamps included with the luminaire. At the same time, this Regulation should not impose a disproportionate administrative burden on luminaire manufacturers and retailers, nor should it discriminate between luminaires as regards the obligation to provide consumers with information on energy efficiency.

(6)

The information provided on the label should be obtained through reliable, accurate and reproducible measurement procedures, which take into account the recognised state-of-the-art measurement methods including, where available, harmonised standards adopted by the European standardisation bodies, as listed in Annex I to Directive 98/34/EC of the European Parliament and of the Council (3).

(7)

This Regulation should specify a uniform design and content for the label for electrical lamps and luminaires.

(8)

In addition, this Regulation should specify requirements for the technical documentation of electrical lamps and luminaires and for the fiche of electrical lamps.

(9)

Moreover, this Regulation should specify requirements for the information to be provided for any form of distance selling, advertisements and technical promotional materials for electrical lamps and luminaires.

(10)

It is appropriate to provide for a review of the provisions of this Regulation taking into account technological progress.

(11)

In order to facilitate the transition from Directive 98/11/EC to this Regulation, household lamps labelled in accordance with this Regulation should be considered compliant with Directive 98/11/EC.

(12)

Directive 98/11/EC should therefore be repealed,

(1)

‘Light source’ means a surface or object designed to emit mainly visible optical radiation produced by a transformation of energy. The term ‘visible’ refers to a wavelength of 380-780 nm;

(2)

‘Lighting’ means the application of light to a scene, objects or their surroundings so that they may be seen by humans;

(3)

‘Accent lighting’ means a form of lighting where light is directed so as to highlight an object or a part of an area;

(4)

‘Lamp’ means a unit whose performance can be assessed independently and which consists of one or more light sources. It may include additional components necessary for starting, power supply or stable operation of the unit or for distributing, filtering or transforming the optical radiation, in cases where those components cannot be removed without permanently damaging the unit;

(5)

‘Lamp cap’ means that part of a lamp which provides connection to the electrical supply by means of a lamp holder or lamp connector and may also serve to retain the lamp in the lamp holder;

(6)

‘Lamp holder’ or ‘socket’ means a device which holds the lamp in position, usually by having the cap inserted in it, in which case it also provides the means of connecting the lamp to the electric supply;

(7)

‘Directional lamp’ means a lamp having at least 80 % light output within a solid angle of π sr (corresponding to a cone with angle of 120°);

(8)

‘Non-directional lamp’ means a lamp that is not a directional lamp;

(9)

‘Filament lamp’ means a lamp in which light is produced by means of a threadlike conductor which is heated to incandescence by the passage of an electric current. The lamp may contain gases influencing the process of incandescence;

(10)

‘Incandescent lamp’ means a filament lamp in which the filament operates in an evacuated bulb or is surrounded by inert gas;

(11)

‘(Tungsten) halogen lamp’ means a filament lamp in which the filament is made of tungsten and is surrounded by gas containing halogens or halogen compounds. They may be supplied with an integrated power supply;

(12)

‘Discharge lamp’ means a lamp in which the light is produced, directly or indirectly, by an electric discharge through a gas, a metal vapour or a mixture of several gases and vapours;

(13)

‘Fluorescent lamp’ means a discharge lamp of the low pressure mercury type in which most of the light is emitted by one or more layers of phosphors excited by the ultraviolet radiation from the discharge. Fluorescent lamps may be supplied with an integrated ballast;

(14)

‘Fluorescent lamp without integrated ballast’ means a single- or double-capped fluorescent lamp without integrated ballast;

(15)

‘High-intensity discharge lamp’ means an electric discharge lamp in which the light producing arc is stabilised by wall temperature and the arc has a bulb wall loading in excess of 3 watts per square centimetre;

(16)

‘Light-emitting diode (LED)’ means a light source which consists of a solid state device embodying a p-n junction. The junction emits optical radiation when excited by an electric current;

(17)

‘LED package’ means an assembly having one or more LED(s). The assembly may include an optical element and thermal, mechanical and electrical interfaces;

(18)

‘LED module’ means an assembly having no cap and incorporating one or more LED packages on a printed circuit board. The assembly may have electrical, optical, mechanical and thermal components, interfaces and control gear;

(19)

‘LED lamp’ means a lamp incorporating one or more LED modules. The lamp may be equipped with a cap;

(20)

‘Lamp control gear’ means a device located between the electrical supply and one or more lamps, which provides a functionality related to the operation of the lamp(s), such as transforming the supply voltage, limiting the current of the lamp(s) to the required value, providing a starting voltage and preheating current, preventing cold starting, correcting the power factor or reducing radio interference. The device may be designed to connect to other lamp control gear to perform these functions. The term does not include:

(21)

‘Control device’ means an electronic or mechanical device controlling or monitoring the luminous flux of the lamp by other means than power conversion for the lamp, such as timer switches, occupancy sensors, light sensors and daylight regulation devices. In addition, phase cut dimmers shall also be considered as control devices;

(22)

‘External lamp control gear’ means non-integrated lamp control gear designed to be installed outside the enclosure of a lamp or luminaire, or to be removed from the enclosure without permanently damaging the lamp or the luminaire;

(23)

‘Ballast’ means lamp control gear inserted between the supply and one or more discharge lamps which by means of inductance, capacitance or a combination of inductance and capacitance, serves mainly to limit the current of the lamp(s) to the required value;

(24)

‘Halogen lamp control gear’ means lamp control gear that transforms mains voltage to extra low voltage for halogen lamps;

(25)

‘Compact fluorescent lamp’ means a fluorescent lamp that includes all the components necessary for starting and stable operation of the lamp;

(26)

‘Luminaire’ means an apparatus which distributes, filters or transforms the light transmitted from one or more lamps and which includes all the parts necessary for supporting, fixing and protecting the lamps and, where necessary, circuit auxiliaries together with the means for connecting them to the electric supply;

(27)

‘Point of sale’ means a physical location where the product is displayed or offered for sale, hire or hire-purchase to the end-user;

(28)

‘End-user’ means a natural person buying or expected to buy an electrical lamp or luminaire for purposes which are outside his trade, business, craft or profession;

(29)

‘Final owner’ means the person or entity owning a product during the use phase of its life cycle, or any person or entity acting on behalf of such a person or entity.

(1)

Implementing Regulation (EU) No 543/2011 lays down, pursuant to the outcome of the Uruguay Round multilateral trade negotiations, the criteria whereby the Commission fixes the standard values for imports from third countries, in respect of the products and periods stipulated in Annex XVI, Part A thereto.

(2)

The standard import value is calculated each working day, in accordance with Article 136(1) of Implementing Regulation (EU) No 543/2011, taking into account variable daily data. Therefore this Regulation should enter into force on the day of its publication in the Official Journal of the European Union,

(1)

The representative prices and additional duties applicable to imports of white sugar, raw sugar and certain syrups for the 2011/12 marketing year are fixed by Commission Implementing Regulation (EU) No 971/2011 (3). Those prices and duties were last amended by Commission Implementing Regulation (EU) No 860/2012 (4).

(2)

The data currently available to the Commission indicate that those amounts should be amended in accordance with Article 36 of Regulation (EC) No 951/2006.

(3)

Given the need to ensure that this measure applies as soon as possible after the updated data have been made available, this Regulation should enter into force on the day of its publication,

(1)

On 22 December 2009 and on 18 January 2010, the Council adopted Decisions 2009/1014/EU (1) and 2010/29/EU (2) appointing the members and alternate members of the Committee of the Regions for the period from 26 January 2010 to 25 January 2015.

(2)

An alternate member’s seat has become vacant following the end of the term of office of Mr Angelo ZUBBANI,

—

Mr Leoluca ORLANDO, Sindaco del Comune di Palermo.

(1)

On 22 December 2009 and on 18 January 2010, the Council adopted Decisions 2009/1014/EU (1) and 2010/29/EU (2) appointing the members and alternate members of the Committee of the Regions for the period from 26 January 2010 to 25 January 2015.

(2)

Two members’ seats on the Committee of the Regions have become vacant following the end of the terms of office of Mr Savvas ELIOFOTOU and Mr Evyenios MICHAIL. Three alternate members’ seats on the Committee of the Regions have become vacant following the end of the terms of office of Mr Andreas MOUSEOS, Mr Andreas HADZILOIZOU and Mr Christofis ANTONIOU,

(a)

as members:

and

(b)

as alternate members:

(1)

On 22 December 2009 and on 18 January 2010, the Council adopted Decisions 2009/1014/EU (1) and 2010/29/EU (2) appointing the members and alternate members of the Committee of the Regions for the period from 26 January 2010 to 25 January 2015.

(2)

Two alternate members’ seats have become vacant following the end of the terms of office of Mr Jacek CZERNIAK and Mr Marcin JABŁOŃSKI,

—

Mr Piotr CAŁBECKI, Marszałek Województwa Kujawsko-Pomorskiego,

—

Mr Jarosław DWORZAŃSKI, Marszałek Województwa Podlaskiego.

(1)

On 22 December 2009 and on 18 January 2010, the Council adopted Decisions 2009/1014/EU (1) and 2010/29/EU (2) appointing the members and alternate members of the Committee of the Regions for the period from 26 January 2010 to 25 January 2015.

(2)

An alternate member’s seat has become vacant following the end of the term of office of Ms Barbara BONINO,

—

Mr Mattia TARSI, Consigliere, Provincia di Pesaro.