Parameter

Organisation

Reference/Title

Notes

(1)

(2)

(3)

(4)

Solid fuel boilers, including condensing boilers and solid fuel cogeneration boilers

General conditions for testing

CEN

EN303-5:2012 Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW — Terminology, requirements and marking, 5.7 Conducting the boiler performance test

Condensing boilers are to be tested in condensing mode.

The applicable part load (30 % or 50 %) is to be used instead of the minimum heat output.

Useful efficiency at rated heat output ηn

CEN

EN303-5:2012, 3.15 boiler efficiency, 5.10.3.1 Direct method

Corresponds to ηK measured at rated heat output Pr , but with Q and QB expressed in gross calorific value.

Useful efficiency at applicable part load ηp

CEN

EN303-5:2012, 3.15, 5.10.3.1

Corresponds to ηK measured at applicable part load (30 % or 50 %), but with Q and QB expressed in gross calorific value.

Useful heat output at rated heat output Pn

CEN

EN303-5:2012, 3.6 heat output

Corresponds to heat output Q measured at rated heat output Pr , but expressed in gross calorific value.

Useful heat output at applicable part load Pp

CEN

EN303-5:2012, 3.6

Corresponds heat output Q measured at applicable part load (30 % or 50 %), but expressed in gross calorific value.

Rated heat output Pr

CEN

EN303-5:2012, 3.7 nominal heat output, 5.8.2 Determining the nominal heat output

Corresponds to nominal heat output QN (when measured with the preferred fuel), but expressed in gross calorific value.

Electrical power requirement at maximum heat output elmax

CEN

EN303-5:2012, 5.8.5 Electrical consumption

EN15456:2008, Heating boilers — Electrical power consumption for heat generators — System boundaries — Measurements

Corresponds to Paux 100 in clause 3.4.1 of EN15456:2008, but any electricity consumption from a back-up heater and from incorporated secondary emission abatement equipment is not taken into account.

Electrical power requirement at minimum heat output elmin

CEN

EN303-5:2012, 5.8.5

EN15456:2008

Corresponds to Paux, g in clause 3.4.1 of EN15456:2008 measured at applicable part load operation (30 % or 50 %), but any electricity consumption from a back-up heater and from incorporated secondary emission abatement equipment is not taken into account.

Standby mode power consumption PSB

CEN

EN303-5:2012, 5.8.5

EN15456:2008

Corresponds to Paux sb , but any electricity consumption from incorporated secondary emission abatement equipment is not taken into account.

Gross calorific value moisture free GCVmf

CEN

EN 14918:2009 Solid biofuels — Determination of calorific value, 10.4 Expression of results

Corresponds to qV, gr, d

Moisture content of the fuel M

CEN

EN 14918:2009, 10.4

Corresponds to Mar , but expressed as fraction instead of as percentage

Characteristics for log wood, moisture content ≤ 25 %

CEN

EN303-5:2012, Table 7 — test fuels, water content and ash content for wood logs

Characteristics for chipped wood, moisture content 15-35 %

CEN

EN303-5:2012, Table 7, water content and ash content for chipped wood B1

Characteristics for chipped wood, moisture content > 35 %

CEN

EN303-5:2012, Table 7, water content and ash content for chipped wood B2

Characteristics for compressed wood in the form of pellets or briquettes

CEN

EN303-5:2012, Table 7, water content and ash content for compressed wood

Characteristics for sawdust, moisture content ≤ 50 %

CEN

EN303-5:2012, Table 7, water content and ash content for sawdust

Characteristics for bituminous coal

CEN

EN303-5:2012, Table 7, water content, ash content and volatiles for bituminous coal

Characteristics for brown coal (including briquettes)

CEN

EN303-5:2012, Table 7, water content, ash content and volatiles for brown coal

Characteristics for coke

CEN

EN303-5:2012, Table 7, water content, ash content and volatiles for coke

Characteristics for anthracite

CEN

EN303-5:2012, Table 7, water content, ash content and volatiles for anthracite

Characteristics for blended fossil fuel briquettes

European Commission

In ‘Notes’

Water content (as received) ≤ 14 %; ash content 5 ± 2 %; volatiles < 18 %

Characteristics for blended biomass (30-70 %)/fossil fuel briquettes

European Commission

In ‘Notes’

Water content (as received) ≤ 14 %; ash content 5 ± 2 %; volatiles 20 % to 60 %

Solid fuel cogeneration boilers

Electrical efficiency ηel, n

CEN

FprEN50465:2013, Gas appliances — Combined Heat and Power appliance of nominal heat input inferior or equal to 70 kW, 7.6.1 Efficiency (Hi)

Corresponds to ηHs, el, CHP_100+Sup_0 , but with the denominator of the formula adapted for solid fuel input and representing gross calorific value.

Parameter

ESO

Reference/title

Notes

(1)

(2)

(3)

(4)

Solid fuel fired local space heaters

Useful efficiency at nominal and minimum heat output: ηth, nom, ηth, min

CEN

for all other open/closed fronted appliances and cookers: EN 16510-1:2013 § 7.3, A.6.2

for pellet fired appliances: EN 14785:2006 § 6.4.2, A.4.7 & A.4.8

for slow heat release appliances: EN 15250:2007-06 § 6.3, A.4.6 & A.5 & A.6.2.2

Standard series EN 16510 will replace:

EN 13240:2001 (EN 13240:2001/A2:2004/C2:2007)

EN 13229:2001 (EN 13229:2011 § 6.8)

EN 12815:2001

EN 12809:2001

Seasonal space heating efficiency ηs

CEN

(read Note)

According to Commission Regulation (EU) 2015/1188 of 28 April 2015, implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for local space heaters.

Nominal heat output, minimum heat output: Pnom, Pmin

CEN

EN 16510-1:2013 A.4.7 & A.4.8, EN 14785:2006 § 6.5, A.4.7 & A.4.8

EN 15250:2007-06 § 6.3 & A.6.2.2

Pnom corresponds to PN in EN 16510-1:2013.

Pmin corresponds to reduced heat output in EN 16510-1:2013.

Pmin corresponds to reduced heat output in EN 14785:2006.

Pnom corresponds to P in EN 15250:2007. Pmin is not described in EN 15250:2007, but shall be established (if applicable) in a similar way as the nominal heat output.

Permanent pilot flame power requirement Ppilot

Direct heat output

CEN

EN 14785:2006, A 6.2.4

EN 15250:2007, A.6.2.2

EN 16510-1:2013, A.6.2.4

Indirect heat output

CEN

EN 14785:2006 A.6.2.3

EN 16510-1:2013 A.6.2.3

For slow heat release stoves no heat output to water calculation is presented. In case the appliances do have such output, the calculation principles of prEN16510-1 shall be used.

Electrical power consumption at nominal heat output, elmax

CEN

EN 15456:2008-06 § 3.4.1 & § 5.1.3.1.

Corresponds to Paux 100.

EN16510-1 requires ‘electrical auxiliary energy, in W, if applicable’ to be shown on the appliance marking, but no methods to establish this has been provided.

The principal EN15456 shall be used.

Electrical power consumption at minimum heat output, elmin

CEN

EN 15456:2008-06 § 3.4.1 & § 5.1.3.2.

As minimum heat output shall be used the minimum output as declared by the manufacturer of the appliances.

Corresponds to Paux,30 .

Standby mode power consumption, elsb

CEN

EN 15456:2008-06 § 3.4.1 & § 5.1.3.3

or

IEC 62301 Ed. 2.0 b:2011 § 5.3

Corresponds to Paux sb Corresponds to power consumption in standby mode in IEC 62301 Ed. 2.0: 2011.

Emissions of particulate matter (PM), according Annex III 4 a) i) (1) (‘heated filter’)

CEN

for measurement according (heated filter) EN 16510-1:2013, G.2

Emissions of particulate matter (PM), according Annex III 4 a) i) (2) (‘dilution tunnel’)

CEN

for measurement according (full flow dilution tunnel) CEN/TS 15883:2009 Annex A.2

Emissions of particulate matter (PM), according to Annex III 4 a) i) (3)

CEN

for measurement according CEN/TS 15883:2009 Annex A.3

Emissions of organic gaseous compounds (OGC)

CEN

EN 16510-1:2013, F.4

Emissions of carbon monoxide (CO)

CEN

EN 16510-1:2013 A.4.4.2 and A.6.2.6

Emissions of nitrogen oxides (NOx)

CEN

EN 16510-1:2013 Annex E.5

Test fuel specifications

CEN

prEN 16510-1:2013 Annex B

For blended fossil fuel briquettes: water content (as received) ≤ 14 %; ash content 5 ± 2 %; volatiles < 18 %.

For blended biomass (30-70 %) fossil fuel briquettes: water content (as received) ≤ 14 %; ash content 5 ± 2 %; volatiles 20 % to 60 %.

Gaseous fuel fired local space heaters, except luminous heaters and tube heaters

Direct heat output

CEN

EN 613:2000

EN 1266:2002 § 3.5.1.3 & § 3.5.1.4 and § 7.12.

EN 13278:2013 Open fronted gas-fired independent space heaters § 6.3 & § 6.12 & § 7.12 & § 7.3.1

EN 449:2002+A1:2007

This is the heat output to the space the product is installed in.

Corresponds to Qout in EN 1319:2009 and EN 1266:2002 and EN 13278:2013 and shall be calculated with the equation Qout = QN * ηΝ, where QN is the nominal heat input and ηΝ is the nominal efficiency. Qout shall be calculated as gross calorific value.

Indirect heat output

CEN

(read Note)

The indirect heat output of gas fired local space heaters is not described in EN standards.

For the purpose of declaration and verification the principles as applied in EN 15610-1 may be used.

Useful efficiency at nominal and minimum heat output: ηth, nom, ηth, min

CEN

prEN 613:2000 § 7.11.2

EN 1266:2002 § 6.12 & § 7.12

EN 13278:2013 § 6.12 & § 7.12

EN 613 ηth, nom and ηth, min shall be calculated as η in conditions applicable to the nominal and minimum heat output, if relevant.

ηth, nom corresponds to η if determined with nominal heat input. ηth, min corresponds to η if determined with minimum heat input in EN 1266:2002 and EN 13278:2013.

All values shall be based on net calorific value.

Nominal heat output, minimum heat output: Pnom, Pmin

CEN

prEN 613:2000

EN 1266:2002 § 6.3.1 & § 7.3.1 and § 6.12 & § 7.12

EN 13278:2013 § 6.3.1 & § 7.3.1

EN 449:2202+A1:2007

EN 613 Pnom shall be determined as Pnom = Qn * η applicable to nominal output conditions. For Qn see § 7.3.1. Pmin shall be determined as Pmin = Qmin * η for minimum output conditions. For Qmin see § 7.3.5.

Pnom shall be determined with Pnom = Qn * ηth nom and Pmin shall be determined with Pmin = Qm * ηth, min. in EN 1266:2002 and EN 13278:2013.

All values shall be based on net calorific value.

Electrical power consumption at nominal heat output, elmax

CEN

EN15456:2008 06: § 3.4.1

elmax corresponds to Paux 100 in EN15456:2008, measured at nominal load operation.

Electrical power consumption at minimum heat output, elmin

CEN

EN15456:2008-06: § 3.4.1

elmin corresponds to Paux 30 , measured at an applicable part load operation.

Standby mode power consumption, elsb

CEN

EN15456:2008-06: § 3.4.1

or

IEC 62301 Ed. 2.0 b:2011 § 5.3

elsb corresponds to either Paux sb in EN15456:2008 or to the power consumption in standby mode in IEC 62301 Ed. 2.0: 2011.

Emissions of nitrogen oxides (NOx)

CEN

prEN 613:2000 § 7.7.4

EN 1266:2002 § 6.7.2 & § 7.7.4 and Annex G

EN 13278:2013 § 6.7.2 & § 7.7.4 and Annex H

prEN61, EN1266 and EN13278 establish NOx emissions as weighted values over full-modulating-minimum load conditions. For declaration and verification purposes the emission at full load NOx(max) applies.

Permanent pilot flame power requirement Ppilot

CEN

according EN1266:2002, § 7.3.1

prEN613 and EN13278 do not have a clause that describes how to calculate the heat input of the ignition burner.

Liquid fuel fired local space heaters

Direct heat output

CEN

EN 1:1998§ 6.6.2

EN 13842:2000: § 6.3 and § 6.6.

The direct heat output is the heat capacity according EN 1:1998§ 6.6.2

In EN 13842 the direct heat output can be calculated as: Q0 * (1-qA)

All values shall be based on net calorific value.

Indirect heat output

CEN

(read Note)

The indirect heat output of liquid fuel fired local space heaters is not described in EN standards.

For the purpose of declaration and verification the principles as applied in EN 15610-1 may be used.

Useful efficiency at nominal and minimum heat output: ηth, nom, ηth, min

CEN

EN 1:1998 § 6.6.1.2

EN 13842: § 6.6.6

Following EN 1:1998 ηth, nom corresponds to η at maximum oil flow rate, ηth, min shall be determined as η at minimum oil flow rate.

Following EN 13842 ηth, nom shall be calculated as ηth, nom = 1-qa, with qa measured at nominal heat input or at minimum heat input (where applicable).

All values shall be based on net calorific value.

Nominal heat output, minimum heat output: Pnom, Pmin

CEN

EN 1:1998-05 § 6.6.2

EN 13842:2000: § 6.3 and § 6.6.

Following EN 1:1998 Pnom corresponds to P at maximum (is nominal) and minimum oil flow rate.

Following EN 13842 the nominal heat output can be calculated as: Q0 * (1-qA) for nominal and minimum heat output conditions.

Electrical power consumption at nominal heat output, elmax

CEN

EN15456:2008-06 Heating boilers. Electrical power consumption for heat generators. System boundaries. Measurements, § 3.4.1. & § 5.1.3.1.

elmax corresponds to Paux 100 in EN15456:2008.

Electrical power consumption at minimum heat output, elmin

CEN

EN15456:2008-06, § 3.4.1. & § 5.1.3.2.

Corresponds to auxiliary power requirement Paux 30 in EN15456:2008

Standby mode power consumption, elsb

CEN

EN15456:2008, § 3.4.1. & § 5.1.3.2. or

IEC 62301 Ed. 2.0 b:2011§ 5.3.

Corresponds to Paux sb in EN15456:2008 electrical power consumption Paux

Corresponds to power consumption in standby mode in IEC 62301 Ed. 2.0: 2011.

Emissions of nitrogen oxides (NOx)

CEN

EN 1:1998 § 6.6.4

EN 13842 does not describe NOx measurement, although § 5.3.2 sets a maximum requirement.

For declaration and verification the method according EN 1 shall be used.

Permanent pilot flame power requirement Ppilot

CEN

EN1266:2002, § 7.3.1

For declaration and verification of such a power requirement the method as in EN1266:2002, § 7.3.1 shall be used.

Electric local space heaters

Nominal heat output (Pnom)

Cenelec

(see Note)

for electric portable, fixed heaters and underfloor heaters: IEC/EN 60675 ed 2.1; 1998 § 16

for electric storage heaters: IEC/EN 60531:1999 § 9

The identification of the nominal heat output is not measured in standards. The electric power input at nominal heat output is considered representative for the nominal heat output.

Pnom corresponds to the following applicable standards:

IEC/EN 60335-1: Household and similar electrical appliances — safety — rated voltage: 250 V for single-phase appliances, up to 480 V for others, not intended for appliances for domestic use as usual.

IEC/EN 60335-2-30: Household and similar electrical appliances — safety — particular requirements for room heaters

IEC/EN 60335-2-61: Household and similar electrical appliances — safety — particular requirements for thermal storage room heaters.

IEC/EN 60335-2-96: Household and similar electrical appliances — safety — particular requirements for flexible sheet heating elements for room heating.

IEC/EN 60335-2-106: Household and similar electrical appliances — safety — particular requirements for heated carpets and for heating units for room heating

IEC/EN 60531:1991. Household electric thermal storage room heaters — methods for measuring performance.

Maximum continuous heat output (Pmax, c)

Cenelec

for electric portable, fixed heaters and underfloor heaters: IEC/EN 60675 ed.2.1:1998 § 9

Pmax, c corresponds to the usable power in IEC 60675 ed. 2.1:1998

Standby mode power consumption, elsb

Cenelec

IEC 62301 Ed. 2.0 b:2011 § 5.3

Corresponds to power consumption in standby mode in IEC 62301 Ed. 2.0: 2011.

Luminous and tube heaters

Useful efficiency at nominal and minimum heat output: ηth, nom, ηth, min

CEN

(read Note)

Neither EN 416 nor EN 419 presents a method for determining the useful efficiency of the heater.

For tube heaters the useful efficiency shall be determined on the basis of the flue gas losses as described in EN 1319, § 7.4.

Values shall be based on gross calorific value.

For luminous heaters a value of 85,6  % shall be assumed (based on gross calorific value of fuel).

Nominal heat output, minimum heat output: Pnom, Pmin

CEN

Luminous heaters: EN 419-1

Tube heaters: EN 416-1

For luminous and tube heaters, the heat output is calculated as:

heat output = heat input Qn * useful efficiency, at nominal or minimum load.

All values shall be based on gross calorific value of fuel.

Fenv

CEN

EN 1886:2007 § 8.2.1

Fenv depends on class T1 to T5 as established by EN 1886.

Radiant factor (RF for nominal and minimum)

CEN

Tube heaters: EN 419-2: § 7.2.1.2

Luminous heaters: EN 416-2 § 7.2.1.2

RF at nominal heat output corresponds to Rf, RF at minimum heat output corresponds to Rf, but measured at minimum heat output.

Rf shall be based on net calorific value.

Electrical power consumption at nominal heat output, elmax

CEN

(read Note)

Neither EN416 nor EN 419 describes a method for determining the electric power requirement.

Therefore for declaration and verification purposes the method and principles as described in EN 15456, but then applicable operating conditions typical to luminous and tube heaters, shall apply.

Electrical power consumption at minimum heat output, elmin

CEN

(read Note)

Neither EN416 nor EN 419 describes a method for determining the electric power requirement.

Therefore for declaration and verification purposes the method and principles as described in EN 15456, but then applicable operating conditions typical to luminous and tube heaters, shall apply.

Standby mode power consumption, elsb

CEN

IEC 62301 Ed. 2.0 b:2011 § 5.3

Corresponds to power consumption in standby mode in IEC 62301 Ed. 2.0: 2011.

Permanent pilot flame power requirement Ppilot

CEN

(read Note)

Neither standard EN 416 nor EN 419 describes a method for determining a power requirement for a permanent pilot flame (ignition burner).

For declaration and verification of such a power requirement the method as in EN1266:2002, § 7.3.1 shall be used.

ESO (1)

Reference and title of the standard

(and reference document)

First publication OJ

Reference of superseded standard

Date of cessation of presumption of conformity of superseded standard

Note 1

(1)

(2)

(3)

(4)

(5)

CEN

EN ISO 9000:2015

Quality management systems — Fundamentals and vocabulary (ISO 9000:2015)

11.12.2015

EN ISO 9000:2005

Note 2.1

15.9.2018

CEN

EN ISO 9001:2015

Quality management systems — Requirements (ISO 9001:2015)

11.12.2015

EN ISO 9001:2008

Note 2.1

15.9.2018

CEN

EN ISO 14001:2015

Environmental management systems — Requirements with guidance for use (ISO 14001:2015)

11.12.2015

EN ISO 14001:2004

Note 2.1

15.9.2018

CEN

EN ISO 14004:2016

Environmental management systems — General guidelines on implementation (ISO 14004:2016)

10.6.2016

EN ISO 14004:2010

Note 2.1

30.4.2019

CEN

EN ISO 14015:2010

Environmental management — Environmental assessment of sites and organizations (EASO) (ISO 14015:2001)

5.10.2011

CEN

EN ISO 14020:2001

Environmental labels and declarations — General principles (ISO 14020:2000)

16.6.2009

CEN

EN ISO 14021:2016

Environmental labels and declarations — Self-declared environmental claims (Type II environmental labelling) (ISO 14021:2016)

12.8.2016

EN ISO 14021:2001

Note 2.1

31.10.2018

CEN

EN ISO 14024:2000

Environmental labels and declarations — Type I environmental labelling — Principles and procedures (ISO 14024:1999)

16.6.2009

CEN

EN ISO 14031:2013

Environmental management — Environmental performance evaluation — Guidelines (ISO 14031:2013)

28.11.2013

EN ISO 14031:1999

Note 2.1

28.2.2014

CEN

EN ISO 14040:2006

Environmental management — Life cycle assessment — Principles and framework (ISO 14040:2006)

16.6.2009

CEN

EN ISO 14044:2006

Environmental management — Life cycle assessment — Requirements and guidelines (ISO 14044:2006)

16.6.2009

CEN

EN ISO 14050:2010

Environmental management — Vocabulary (ISO 14050:2009)

5.10.2011

CEN

EN ISO 14063:2010

Environmental management — Environmental communication — Guidelines and examples (ISO 14063:2006)

5.10.2011

CEN

EN ISO 14064-1:2012

Greenhouse gases — Part 1: Specification with guidance at the organization level for quantification and reporting of greenhouse gas emissions and removals (ISO 14064-1:2006)

28.11.2013

CEN

EN ISO 14064-2:2012

Greenhouse gases — Part 2: Specification with guidance at the project level for quantification, monitoring and reporting of greenhouse gas emission reductions or removal enhancements (ISO 14064-2:2006)

28.11.2013

CEN

EN ISO 14064-3:2012

Greenhouse gases — Part 3: Specification with guidance for the validation and verification of greenhouse gas assertions (ISO 14064-3:2006)

28.11.2013

CEN

EN ISO 14065:2013

Greenhouse gases — Requirements for greenhouse gas validation and verification bodies for use in accreditation or other forms of recognition (ISO 14065:2013)

7.9.2013

EN ISO 14065:2012

Note 2.1

31.10.2013

CEN

EN ISO 15189:2012

Medical laboratories — Requirements for quality and competence (ISO 15189:2012, Corrected version 2014-08-15)

13.3.2013

EN ISO 15189:2007

Note 2.1

30.11.2015

CEN

EN ISO 15195:2003

Laboratory medicine — Requirements for reference measurement laboratories (ISO 15195:2003)

5.10.2011

CEN

EN ISO/IEC 17000:2004

Conformity assessment — Vocabulary and general principles (ISO/IEC 17000:2004)

16.6.2009

CEN

EN ISO/IEC 17011:2004

Conformity assessment — General requirements for accreditation bodies accrediting conformity assessment bodies (ISO/IEC 17011:2004)

16.6.2009

CEN

EN ISO/IEC 17020:2012

Conformity assessment — Requirements for the operation of various types of bodies performing inspection (ISO/IEC 17020:2012)

25.5.2012

EN ISO/IEC 17020:2004

Note 2.1

1.3.2015

CEN

EN ISO/IEC 17021-1:2015

Conformity assessment — Requirements for bodies providing audit and certification of management systems — Part 1: Requirements (ISO/IEC 17021-1:2015)

11.12.2015

EN ISO/IEC 17021:2011

Note 2.1

8.7.2017

CEN

EN ISO/IEC 17024:2012

Conformity assessment — General requirements for bodies operating certification of persons (ISO/IEC 17024:2012)

7.9.2013

EN ISO/IEC 17024:2003

Note 2.1

1.7.2015

CEN

EN ISO/IEC 17025:2005

General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025:2005)

16.6.2009

EN ISO/IEC 17025:2005/AC:2006

16.6.2009

CEN

EN ISO/IEC 17040:2005

Conformity assessment — General requirements for peer assessment of conformity assessment bodies and accreditation bodies (ISO/IEC 17040:2005)

16.6.2009

CEN

EN ISO/IEC 17043:2010

Conformity assessment — General requirements for proficiency testing (ISO/IEC 17043:2010)

28.11.2013

CEN

EN ISO/IEC 17050-1:2010

Conformity assessment — Supplier's declaration of conformity — Part 1: General requirements (ISO/IEC 17050-1:2004, corrected version 2007-06-15)

5.10.2011

EN ISO/IEC 17050-1:2004

Note 2.1

5.10.2011

CEN

EN ISO/IEC 17050-2:2004

Conformity assessment — Supplier's declaration of conformity — Part 2: Supporting documentation (ISO/IEC 17050-2:2004)

16.6.2009

CEN

EN ISO/IEC 17065:2012

Conformity assessment — Requirements for bodies certifying products, processes and services (ISO/IEC 17065:2012)

7.9.2013

EN 45011:1998

Note 2.1

15.9.2015

CEN

EN ISO/IEC 17067:2013

Conformity assessment — Fundamentals of product certification and guidelines for product certification schemes (ISO/IEC 17067:2013)

12.2.2016

CEN

EN ISO 19011:2011

Guidelines for auditing management systems (ISO 19011:2011)

25.5.2012

EN ISO 19011:2002

Note 2.1

31.5.2012

CEN

EN ISO 22870:2016

Point-of-care testing (POCT) — Requirements for quality and competence (ISO 22870:2016)

This is the first publication

EN ISO 22870:2006

Note 2.1

30.11.2019

ESO (1)

Reference and title of the standard

(and reference document)

First publication OJ

Reference of superseded standard

Date of cessation of presumption of conformity of superseded standard

Note 1

Standard aims to cover Article(s) of Directive 2014/53/EU

(1)

(2)

(3)

(4)

(5)

(6)

ETSI

EN 300 065 V2.1.2

Narrow-band direct-printing telegraph equipment for receiving meteorological or navigational information (NAVTEX); Harmonised Standard covering the essential requirements of Article 3(2) and Article 3(3)(g) of Directive 2014/53/EU

8.7.2016

Article 3(2); Article 3(3)(g)

ETSI

EN 300 086 V2.1.2

Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

9.12.2016

Article 3(2)

ETSI

EN 300 220-2 V3.1.1

Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 2: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU for non-specific radio equipment

This is the first publication

Article 3(2)

ETSI

EN 300 220-3-1 V2.1.1

Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 3-1: Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Low duty cycle high reliability equipment, social alarms equipment operating on designated frequencies (869,200 MHz to 869,250 MHz)

This is the first publication

Article 3(2)

ETSI

EN 300 220-3-2 V1.1.1

Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 3-2: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Wireless alarms operating in designated LDC/HR frequency bands 868,60 MHz to 868,70 MHz, 869,25 MHz to 869,40 MHz, 869,65 MHz to 869,70 MHz

This is the first publication

Article 3(2)

ETSI

EN 300 220-4 V1.1.1

Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 4: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Metering devices operating in designated band 169,400 MHz to 169,475 MHz

This is the first publication

Article 3(2)

ETSI

EN 300 328 V2.1.1

Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 300 330 V2.1.1

Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 300 422-1 V2.1.2

Wireless Microphones; Audio PMSE up to 3 GHz; Part 1: Class A Receivers; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

10.2.2017

Article 3(2)

ETSI

EN 300 422-2 V2.1.1

Wireless Microphones; Audio PMSE up to 3 GHz; Part 2: Class B Receivers; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 300 422-3 V2.1.1

Wireless Microphones; Audio PMSE up to 3 GHz; Part 3: Class C Receivers; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 300 487 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications operating in the 1,5 GHz frequency band; Radio Frequency (RF) specifications covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 300 676-2 V2.1.1

Ground-based VHF hand-held, mobile and fixed radio transmitters, receivers and transceivers for the VHF aeronautical mobile service using amplitude modulation; Part 2: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

8.7.2016

Article 3(2)

ETSI

EN 300 698 V2.1.1

Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard covering the essential requirements of Article 3(2) and Article 3(3)(g) of Directive 2014/53/EU

13.1.2017

Article 3(2); Article 3(3)(g)

ETSI

EN 300 720 V2.1.1

Ultra-High Frequency (UHF) on-board vessels communications systems and equipment; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 301 025 V2.1.1

VHF radiotelephone equipment for general communications and associated equipment for Class ‘D’ Digital Selective Calling (DSC); Harmonised Standard covering the essential requirements of Article 3(2) and Article 3(3)(g) of Directive 2014/53/EU

12.8.2016

Article 3(2); Article 3(3)(g)

ETSI

EN 301 166 V2.1.1

Land Mobile Service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

10.2.2017

Article 3(2)

ETSI

EN 301 360 V2.1.1

Satellite Earth Stations and Systems (SES); Harmonised Standard for Satellite Interactive Terminals (SIT) and Satellite User Terminals (SUT) transmitting towards satellites in geostationary orbit, operating in the 27,5 GHz to 29,5 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 301 406 V2.2.2

Digital Enhanced Cordless Telecommunications (DECT); Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 301 426 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Low data rate Land Mobile satellite Earth Stations (LMES) and Maritime Mobile satellite Earth Stations (MMES) not intended for distress and safety communications operating in the 1,5 GHz/1,6 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 430 V2.1.1

Satellite Earth Stations and Systems (SES); Harmonised Standard for Satellite News Gathering Transportable Earth Stations (SNG TES) operating in the 11 GHz to 12 GHz/13 GHz to 14 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

14.10.2016

Article 3(2)

ETSI

EN 301 444 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Land Mobile Earth Stations (LMES) providing voice and/or data communications, operating in the 1,5 GHz and 1,6 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 459 V2.1.1

Satellite Earth Stations and Systems (SES); Harmonised Standard for Satellite Interactive Terminals (SIT) and Satellite User Terminals (SUT) transmitting towards satellites in geostationary orbit, operating in the 29,5 GHz to 30,0 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

14.10.2016

Article 3(2)

ETSI

EN 301 473 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Aircraft Earth Stations (AES) providing Aeronautical Mobile Satellite Service (AMSS)/Mobile Satellite Service (MSS) and/or the Aeronautical Mobile Satellite on Route Service (AMS(R)S)/Mobile Satellite Service (MSS), operating in the frequency band below 3 GHz covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 559 V2.1.1

Short Range Devices (SRD); Low Power Active Medical Implants (LP-AMI) and associated Peripherals (LP-AMI-P) operating in the frequency range 2 483,5 MHz to 2 500 MHz; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 681 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) of Geostationary mobile satellite systems, including handheld earth stations, for Satellite Personal Communications Networks (S-PCN) under the Mobile Satellite Service (MSS), operating in the 1,5 GHz and 1,6 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 783 V2.1.1

Commercially available amateur radio equipment; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

8.7.2016

Article 3(2)

ETSI

EN 301 839 V2.1.1

Ultra Low Power Active Medical Implants (ULP-AMI) and associated Peripherals (ULP-AMI-P) operating in the frequency range 402 MHz to 405 MHz; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

8.7.2016

Article 3(2)

ETSI

EN 301 841-3 V2.1.1

VHF air-ground Digital Link (VDL) Mode 2; Technical characteristics and methods of measurement for ground-based equipment; Part 3: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 842-5 V2.1.1

VHF air-ground Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of measurement for ground-based equipment; Part 5: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 908-1 V11.1.1

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 1: Introduction and common requirements

9.12.2016

Article 3(2)

ETSI

EN 301 908-10 V4.2.2

Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonised Standard for IMT-2000, FDMA/TDMA (DECT) covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 301 908-11 V11.1.2

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 11: CDMA Direct Spread (UTRA FDD) Repeaters

10.2.2017

Article 3(2)

ETSI

EN 301 908-12 V7.1.1

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 12: CDMA Multi-Carrier (cdma2000) Repeaters

9.9.2016

Article 3(2)

ETSI

EN 301 908-15 V11.1.2

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 15: Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters

10.2.2017

Article 3(2)

ETSI

EN 301 908-20 V6.3.1

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 20: OFDMA TDD WMAN (Mobile WiMAXTM) TDD Base Stations (BS)

14.10.2016

Article 3(2)

ETSI

EN 301 908-21 V6.1.1

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile WiMAXTM) FDD User Equipment (UE)

14.10.2016

Article 3(2)

ETSI

EN 301 908-22 V6.1.1

IMT cellular networks; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 22: OFDMA TDD WMAN (Mobile WiMAXTM) FDD Base Stations (BS)

9.12.2016

Article 3(2)

ETSI

EN 302 054-2 V1.2.1

Meteorological Aids (Met Aids); Radiosondes to be used in the 400,15 MHz to 406 MHz frequency range with power levels ranging up to 200 mW; Part 2: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 302 065-1 V2.1.1

Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 1: Requirements for Generic UWB applications

This is the first publication

Article 3(2)

ETSI

EN 302 065-2 V2.1.1

Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 2: Requirements for UWB location tracking

This is the first publication

Article 3(2)

ETSI

EN 302 065-3 V2.1.1

Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 3: Requirements for UWB devices for ground based vehicular applications

This is the first publication

Article 3(2)

ETSI

EN 302 195 V2.1.1

Short Range Devices (SRD); Ultra Low Power Active Medical Implants (ULP-AMI) and accessories (ULP-AMI-P) operating in the frequency range 9 kHz to 315 kHz Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 302 248 V2.1.1

Navigation radar for use on non-SOLAS vessels; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 302 372 V2.1.1

Short Range Devices (SRD); Tank Level Probing Radar (TLPR) equipment operating in the frequency ranges 4,5 GHz to 7 GHz, 8,5 GHz to 10,6 GHz, 24,05 GHz to 27 GHz, 57 GHz to 64 GHz, 75 GHz to 85 GHz; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 302 454-2 V1.2.1

Meteorological Aids (Met Aids); Radiosondes to be used in the 1 668,4 MHz to 1 690 MHz frequency range; Part 2: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 302 480 V2.1.2

Mobile Communication On Board Aircraft (MCOBA) systems; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

This is the first publication

Article 3(2)

ETSI

EN 302 537 V2.1.1

Ultra Low Power Medical Data Service (MEDS) Systems operating in the frequency range 401 MHz to 402 MHz and 405 MHz to 406 MHz; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 302 617-2 V2.1.1

Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 302 885 V2.1.1

Portable Very High Frequency (VHF) radiotelephone equipment for the maritime mobile service operating in the VHF bands with integrated handheld class D DSC; Harmonised Standard covering the essential requirements of Article 3(2) and Article 3(3)(g) of Directive 2014/53/EU

13.1.2017

Article 3(2); Article 3(3)(g)

ETSI

EN 302 961 V2.1.2

Maritime Personal Homing Beacon intended for use on the frequency 121,5 MHz for search and rescue purposes only; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 039 V2.1.2

Land Mobile Service; Multichannel transmitter specification for the PMR Service; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 084 V2.1.1

Ground Based Augmentation System (GBAS) VHF ground-air Data Broadcast (VDB); Technical characteristics and methods of measurement for ground-based equipment; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 098 V2.1.1

Maritime low power personal locating devices employing AIS; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 303 135 V2.1.1

Electromagnetic compatibility and Radio spectrum Matters (ERM); Coastal Surveillance, Vessel Traffic Services and Harbour Radars (CS/VTS/HR); Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 303 203 V2.1.1

Short Range Devices (SRD); Medical Body Area Network Systems (MBANSs) operating in the 2 483,5 MHz to 2 500 MHz range; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

12.8.2016

Article 3(2)

ETSI

EN 303 204 V2.1.2

Network Based Short Range Devices (SRD); Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 213-6-1 V2.1.1

Advanced Surface Movement Guidance and Control System (A-SMGCS); Part 6: Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU for deployed surface movement radar sensors; Sub-part 1: X-band sensors using pulsed signals and transmitting power up to 100 kW

13.1.2017

Article 3(2)

ETSI

EN 303 339 V1.1.1

Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Fixed pattern antennas; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 340 V1.1.2

Digital Terrestrial TV Broadcast Receivers; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 372-1 V1.1.1

Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 1: Outdoor unit receiving in the 10,7 GHz to 12,75 GHz frequency band

13.1.2017

Article 3(2)

ETSI

EN 303 372-2 V1.1.1

Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU; Part 2: Indoor unit

9.9.2016

Article 3(2)

ETSI

EN 303 609 V12.5.1

Global System for Mobile communications (GSM); GSM Repeaters; Harmonised Standard covering the essential requirements of Article 3(2) of Directive 2014/53/EU

13.1.2017

Article 3(2)

ETSI

EN 303 978 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in geostationary orbit, operating in the 27,5 GHz to 30,0 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ETSI

EN 303 979 V2.1.2

Satellite Earth Stations and Systems (SES); Harmonised Standard for Earth Stations on Mobile Platforms (ESOMP) transmitting towards satellites in non-geostationary orbit, operating in the 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz frequency bands covering the essential requirements of Article 3(2) of Directive 2014/53/EU

11.11.2016

Article 3(2)

ESO (1)

Reference and title of the standard

(and reference document)

Reference of superseded standard

Date of applicability of the standard as a harmonised standard

Date of the end of the co-existence period

(1)

(2)

(3)

(4)

(5)

CEN

EN 1:1998

Flued oil stoves with vaporizing burners

1.1.2008

1.1.2009

EN 1:1998/A1:2007

1.1.2008

1.1.2009

CEN

EN 40-4:2005

Lighting columns — Part 4: Requirements for reinforced and prestressed concrete lighting columns

1.10.2006

1.10.2007

EN 40-4:2005/AC:2006

1.1.2007

1.1.2007

CEN

EN 40-5:2002

Lighting columns — Part 5: Requirements for steel lighting columns

1.2.2003

1.2.2005

CEN

EN 40-6:2002

Lighting columns — Part 6: Requirements for aluminium lighting columns

1.2.2003

1.2.2005

CEN

EN 40-7:2002

Lighting columns — Part 7: Requirements for fibre reinforced polymer composite lighting columns

1.10.2003

1.10.2004

CEN

EN 54-2:1997

Fire detection and fire alarm systems — Part 2: Control and indicating equipment

1.1.2008

1.8.2009

EN 54-2:1997/AC:1999

1.1.2008

1.1.2008

EN 54-2:1997/A1:2006

1.1.2008

1.8.2009

CEN

EN 54-3:2001

Fire detection and fire alarm systems — Part 3: Fire alarm devices — Sounders

1.4.2003

1.6.2009

EN 54-3:2001/A2:2006

1.3.2007

1.6.2009

EN 54-3:2001/A1:2002

1.4.2003

30.6.2005

CEN

EN 54-4:1997

Fire detection and fire alarm systems — Part 4: Power supply equipment

1.10.2003

1.8.2009

EN 54-4:1997/AC:1999

1.6.2005

1.6.2005

EN 54-4:1997/A1:2002

1.10.2003

1.8.2009

EN 54-4:1997/A2:2006

1.6.2007

1.8.2009

CEN

EN 54-5:2000

Fire detection and fire alarm systems — Part 5: Heat detectors — Point detectors

1.4.2003

30.6.2005

EN 54-5:2000/A1:2002

1.4.2003

30.6.2005

CEN

EN 54-7:2000

Fire detection and fire alarm systems — Part 7: Smoke detectors — Point detectors using scattered light, transmitted light or ionization

1.4.2003

1.8.2009

EN 54-7:2000/A2:2006

1.5.2007

1.8.2009

EN 54-7:2000/A1:2002

1.4.2003

30.6.2005

CEN

EN 54-10:2002

Fire detection and fire alarm systems — Part 10: Flame detectors — Point detectors

1.9.2006

1.9.2008

EN 54-10:2002/A1:2005

1.9.2006

1.9.2008

CEN

EN 54-11:2001

Fire detection and fire alarm systems — Part 11: Manual call points

1.9.2006

1.9.2008

EN 54-11:2001/A1:2005

1.9.2006

1.9.2008

CEN

EN 54-12:2015

Fire detection and fire alarm systems — Part 12: Smoke detectors — Line detectors using an optical beam

EN 54-12:2002

8.4.2016

8.4.2019

CEN

EN 54-16:2008

Fire detection and fire alarm systems — Part 16: Voice alarm control and indicating equipment

1.1.2009

1.4.2011

CEN

EN 54-17:2005

Fire detection and fire alarm systems — Part 17: Short-circuit isolators

1.10.2006

1.12.2008

EN 54-17:2005/AC:2007

1.1.2009

1.1.2009

CEN

EN 54-18:2005

Fire detection and fire alarm systems — Part 18: Input/output devices

1.10.2006

1.12.2008

EN 54-18:2005/AC:2007

1.1.2008

1.1.2008

CEN

EN 54-20:2006

Fire detection and fire alarm systems — Part 20: Aspirating smoke detectors

1.4.2007

1.7.2009

EN 54-20:2006/AC:2008

1.8.2009

1.8.2009

CEN

EN 54-21:2006

Fire detection and fire alarm systems — Part 21: Alarm transmission and fault warning routing equipment

1.3.2007

1.6.2009

CEN

EN 54-23:2010

Fire detection and fire alarm systems — Part 23: Fire alarm devices — Visual alarm devices

1.12.2010

31.12.2013

CEN

EN 54-24:2008

Fire detection and fire alarm systems — Part 24: Components of voice alarm systems — Loudspeakers

1.1.2009

1.4.2011

CEN

EN 54-25:2008

Fire detection and fire alarm systems — Part 25: Components using radio links

1.1.2009

1.4.2011

EN 54-25:2008/AC:2012

1.7.2012

1.7.2012

CEN

EN 179:2008

Building hardware — Emergency exit devices operated by a lever handle or push pad, for use on escape routes — Requirements and test methods

EN 179:1997

1.1.2009

1.1.2010

CEN

EN 197-1:2011

Cement — Part 1: Composition, specifications and conformity criteria for common cements

EN 197-1:2000

EN 197-4:2004

1.7.2012

1.7.2013

CEN

EN 295-1:2013

Vitrified clay pipe systems for drains and sewers — Part 1: Requirements for pipes, fittings and joints

EN 295-10:2005

1.11.2013

1.11.2014

CEN

EN 295-4:2013

Vitrified clay pipe systems for drains and sewers — Part 4: Requirements for adaptors, connectors and flexible couplings

EN 295-10:2005

1.11.2013

1.11.2014

CEN

EN 295-5:2013

Vitrified clay pipe systems for drains and sewers — Part 5: Requirements for perforated pipes and fittings

EN 295-10:2005

1.11.2013

1.11.2014

CEN

EN 295-6:2013

Vitrified clay pipes systems for drain and sewers — Part 6: Requirements for components of manholes and inspection chambers

EN 295-10:2005

1.11.2013

1.11.2014

CEN

EN 295-7:2013

Vitrified clay pipe systems for drains and sewers — Part 7: Requirements for pipes and joints for pipe jacking

EN 295-10:2005

1.11.2013

1.11.2014

CEN

EN 331:1998

Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings

1.9.2011

1.9.2012

EN 331:1998/A1:2010

1.9.2011

1.9.2012

CEN

EN 413-1:2011

Masonry cement — Part 1: Composition, specifications and conformity criteria

EN 413-1:2004

1.2.2012

1.2.2013

CEN

EN 416-1:2009

Single burner gas-fired overhead radiant tube heaters for non-domestic use — Part 1: Safety

1.12.2009

1.12.2010

CEN

EN 438-7:2005

High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes

1.11.2005

1.11.2006

CEN

EN 442-1:2014

Radiators and convectors — Part 1: Technical specifications and requirements

EN 442-1:1995

13.11.2015

13.11.2016

CEN

EN 450-1:2012

Fly ash for concrete — Part 1: Definition, specifications and conformity criteria

EN 450-1:2005+A1:2007

1.5.2013

1.5.2014

CEN

EN 459-1:2010

Building lime — Part 1: Definitions, specifications and conformity criteria

EN 459-1:2001

1.6.2011

1.6.2012

CEN

EN 490:2011

Concrete roofing tiles and fittings for roof covering and wall cladding — Product specifications

EN 490:2004

1.8.2012

1.8.2012

CEN

EN 492:2012

Fibre-cement slates and fittings — Product specification and test methods

EN 492:2004

1.7.2013

1.7.2013

CEN

EN 494:2012+A1:2015

Fibre-cement profiled sheets and fittings — Product specification and test methods

EN 494:2012

8.4.2016

8.4.2017

CEN

EN 516:2006

Prefabricated accessories for roofing — Installations for roof access — Walkways, treads and steps

1.11.2006

1.11.2007

CEN

EN 517:2006

Prefabricated accessories for roofing — Roof safety hooks

1.12.2006

1.12.2007

CEN

EN 520:2004+A1:2009

Gypsum plasterboards — Definitions, requirements and test methods

EN 520:2004

1.6.2010

1.12.2010

CEN

EN 523:2003

Steel strip sheaths for prestressing tendons — Terminology, requirements, quality control

1.6.2004

1.6.2005

CEN

EN 534:2006+A1:2010

Corrugated bitumen sheets — Product specification and test methods

EN 534:2006

1.1.2011

1.1.2011

CEN

EN 544:2011

Bitumen shingles with mineral and/or synthetic reinforcements — Product specification and test methods

EN 544:2005

1.4.2012

1.4.2012

CEN

EN 572-9:2004

Glass in building — Basic soda lime silicate glass products — Part 9: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 588-2:2001

Fibre cement pipes for drains and sewers — Part 2: Manholes and inspection chambers

1.10.2002

1.10.2003

CEN

EN 598:2007+A1:2009

Ductile iron pipes, fittings, accessories and their joints for sewerage applications — Requirements and test methods

EN 598:2007

1.4.2010

1.4.2011

CEN

EN 621:2009

Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products

1.8.2010

1.8.2011

CEN

EN 671-1:2012

Fixed firefighting systems — Hose systems — Part 1: Hose reels with semi-rigid hose

EN 671-1:2001

1.3.2013

1.7.2013

CEN

EN 671-2:2012

Fixed firefighting systems — Hose systems — Part 2: Hose systems with lay-flat hose

EN 671-2:2001

1.3.2013

1.7.2013

CEN

EN 681-1:1996

Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber

1.1.2003

1.1.2009

EN 681-1:1996/A2:2002

1.1.2003

1.1.2004

EN 681-1:1996/A3:2005

1.1.2008

1.1.2009

EN 681-1:1996/A1:1998

1.1.2003

1.1.2004

CEN

EN 681-2:2000

Elastomeric Seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers

1.1.2003

1.1.2004

EN 681-2:2000/A1:2002

1.1.2003

1.1.2004

EN 681-2:2000/A2:2005

1.1.2010

1.1.2010

CEN

EN 681-3:2000

Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 3: Cellular materials of vulcanized rubber

1.1.2003

1.1.2004

EN 681-3:2000/A1:2002

1.1.2003

1.1.2004

EN 681-3:2000/A2:2005

1.7.2012

1.7.2012

CEN

EN 681-4:2000

Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 4: Cast polyurethane sealing elements

1.1.2003

1.1.2004

EN 681-4:2000/A1:2002

1.1.2003

1.1.2004

EN 681-4:2000/A2:2005

1.7.2012

1.7.2012

CEN

EN 682:2002

Elastomeric Seals — Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

1.10.2002

1.12.2003

EN 682:2002/A1:2005

1.7.2012

1.7.2012

CEN

EN 771-1:2011+A1:2015

Specification for masonry units — Part 1: Clay masonry units

EN 771-1:2011

10.6.2016

10.6.2017

CEN

EN 771-2:2011+A1:2015

Specification for masonry units — Part 2: Calcium silicate masonry units

EN 771-2:2011

10.6.2016

10.6.2017

CEN

EN 771-3:2011+A1:2015

Specification for masonry units — Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)

EN 771-3:2011

10.6.2016

10.6.2017

CEN

EN 771-4:2011+A1:2015

Specification for masonry units — Part 4: Autoclaved aerated concrete masonry units

EN 771-4:2011

10.6.2016

10.6.2017

CEN

EN 771-5:2011+A1:2015

Specification for masonry units — Part 5: Manufactured stone masonry units

EN 771-5:2011

10.6.2016

10.6.2017

CEN

EN 771-6:2011+A1:2015

Specification for masonry units — Part 6: Natural stone masonry units

EN 771-6:2011

8.4.2016

8.4.2017

CEN

EN 777-1:2009

Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use — Part 1: System D — Safety

1.11.2009

1.11.2010

CEN

EN 777-2:2009

Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use — Part 2: System E — Safety

1.11.2009

1.11.2010

CEN

EN 777-3:2009

Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use — Part 3: System F — Safety

1.11.2009

1.11.2010

CEN

EN 777-4:2009

Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use — Part 4: System H — Safety

1.11.2009

1.11.2010

CEN

EN 778:2009

Domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 70 kW, without a fan to assist transportation of combustion air and/or combustion products

1.8.2010

1.8.2011

CEN

EN 845-1:2013+A1:2016

Specification for ancillary components for masonry — Part 1: Wall ties, tension straps, hangers and brackets

EN 845-1:2013

10.3.2017

10.3.2018

CEN

EN 845-2:2013+A1:2016

Specification for ancillary components for masonry — Part 2: Lintels

EN 845-2:2013

10.3.2017

10.3.2018

CEN

EN 845-3:2013+A1:2016

Specification for ancillary components for masonry — Part 3: Bed joint reinforcement of steel meshwork

EN 845-3:2013

10.3.2017

10.3.2018

CEN

EN 858-1:2002

Separator systems for light liquids (e.g. oil and petrol) — Part 1: Principles of product design, performance and testing, marking and quality control

1.9.2005

1.9.2006

EN 858-1:2002/A1:2004

1.9.2005

1.9.2006

CEN

EN 877:1999

Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings — Requirements, test methods and quality assurance

1.1.2008

1.9.2009

EN 877:1999/A1:2006

1.1.2008

1.9.2009

EN 877:1999/A1:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 934-2:2009+A1:2012

Admixtures for concrete, mortar and grout — Part 2: Concrete admixtures — Definitions, requirements, conformity, marking and labelling

EN 934-2:2009

1.3.2013

1.9.2013

CEN

EN 934-3:2009+A1:2012

Admixtures for concrete, mortar and grout — Part 3: Admixtures for masonry mortar — Definitions, requirements, conformity and marking and labelling

EN 934-3:2009

1.3.2013

1.9.2013

CEN

EN 934-4:2009

Admixtures for concrete, mortar and grout — Part 4: Admixtures for grout for prestressing tendons — Definitions, requirements, conformity, marking and labelling

EN 934-4:2001

1.3.2010

1.3.2011

CEN

EN 934-5:2007

Admixtures for concrete, mortar and grout — Part 5: Admixtures for sprayed concrete — Definitions, requirements, conformity, marking and labelling

1.1.2009

1.1.2010

CEN

EN 969:2009

Ductile iron pipes, fittings, accessories and their joints for gas pipelines — Requirements and test methods

1.1.2010

1.1.2011

CEN

EN 997:2012

WC pans and WC suites with integral trap

EN 997:2003

1.12.2012

1.6.2013

EN 997:2012/AC:2012

1.3.2013

1.3.2013

CEN

EN 998-1:2010

Specification for mortar for masonry — Part 1: Rendering and plastering mortar

EN 998-1:2003

1.6.2011

1.6.2012

CEN

EN 998-2:2010

Specification for mortar for masonry — Part 2: Masonry mortar

EN 998-2:2003

1.6.2011

1.6.2012

CEN

EN 1013:2012+A1:2014

Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings — Requirements and test methods

EN 1013:2012

10.7.2015

10.7.2016

CEN

EN 1020:2009

Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products

1.8.2010

1.8.2011

CEN

EN 1036-2:2008

Glass in building — Mirrors from silver-coated float glass for internal use — Part 2: Evaluation of conformity; product standard

1.1.2009

1.1.2010

CEN

EN 1051-2:2007

Glass in building — Glass blocks and glass pavers — Part 2: Evaluation of conformity/Product standard

1.1.2009

1.1.2010

CEN

EN 1057:2006+A1:2010

Copper and copper alloys — Seamless, round copper tubes for water and gas in sanitary and heating applications

EN 1057:2006

1.12.2010

1.12.2010

CEN

EN 1090-1:2009+A1:2011

Execution of steel structures and aluminium structures — Part 1: Requirements for conformity assessment of structural components

EN 1090-1:2009

1.9.2012

1.7.2014

CEN

EN 1096-4:2004

Glass in building — Coated glass — Part 4: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 1123-1:1999

Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems — Part 1: Requirements, testing, quality control

1.6.2005

1.6.2006

EN 1123-1:1999/A1:2004

1.6.2005

1.6.2006

CEN

EN 1124-1:1999

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems — Part 1: Requirements, testing, quality control

1.6.2005

1.6.2006

EN 1124-1:1999/A1:2004

1.6.2005

1.6.2006

CEN

EN 1125:2008

Building hardware — Panic exit devices operated by a horizontal bar, for use on escape routes — Requirements and test methods

EN 1125:1997

1.1.2009

1.1.2010

CEN

EN 1154:1996

Building hardware — Controlled door closing devices — Requirements and test methods

1.10.2003

1.10.2004

EN 1154:1996/A1:2002

1.10.2003

1.10.2004

EN 1154:1996/A1:2002/AC:2006

1.1.2010

1.1.2010

CEN

EN 1155:1997

Building hardware — Electrically powered hold-open devices for swing doors — Requirements and test methods

1.10.2003

1.10.2004

EN 1155:1997/A1:2002

1.10.2003

1.10.2004

EN 1155:1997/A1:2002/AC:2006

1.1.2010

1.1.2010

CEN

EN 1158:1997

Building hardware — Door coordinator devices — Requirements and test methods

1.10.2003

1.10.2004

EN 1158:1997/A1:2002/AC:2006

1.6.2006

1.6.2006

EN 1158:1997/A1:2002

1.10.2003

1.10.2004

CEN

EN 1168:2005+A3:2011

Precast concrete products — Hollow core slabs

EN 1168:2005+A2:2009

1.7.2012

1.7.2013

CEN

EN 1279-5:2005+A2:2010

Glass in building — Insulating glass units — Part 5: Evaluation of conformity

EN 1279-5:2005+A1:2008

1.2.2011

1.2.2012

CEN

EN 1304:2005

Clay roofing tiles and fittings — Product definitions and specifications

1.2.2006

1.2.2007

CEN

EN 1317-5:2007+A2:2012

Road restraint systems — Part 5: Product requirements and evaluation of conformity for vehicle restraint systems

EN 1317-5:2007+A1:2008

1.1.2013

1.1.2013

EN 1317-5:2007+A2:2012/AC:2012

1.3.2013

1.3.2013

CEN

EN 1319:2009

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

1.10.2010

1.10.2011

CEN

EN 1337-3:2005

Structural bearings — Part 3: Elastomeric bearings

1.1.2006

1.1.2007

CEN

EN 1337-4:2004

Structural bearings — Part 4: Roller bearings

1.2.2005

1.2.2006

EN 1337-4:2004/AC:2007

1.1.2008

1.1.2008

CEN

EN 1337-5:2005

Structural bearings — Part 5: Pot bearings

1.1.2006

1.1.2007

CEN

EN 1337-6:2004

Structural bearings — Part 6: Rocker bearings

1.2.2005

1.2.2006

CEN

EN 1337-7:2004

Structural bearings — Part 7: Spherical and cylindrical PTFE bearings

EN 1337-7:2000

1.12.2004

1.6.2005

CEN

EN 1337-8:2007

Structural bearings — Part 8: Guide Bearings and Restraint Bearings

1.1.2009

1.1.2010

CEN

EN 1338:2003

Concrete paving blocks — Requirements and test methods

1.3.2004

1.3.2005

EN 1338:2003/AC:2006

1.1.2007

1.1.2007

CEN

EN 1339:2003

Concrete paving flags — Requirements and test methods

1.3.2004

1.3.2005

EN 1339:2003/AC:2006

1.1.2007

1.1.2007

CEN

EN 1340:2003

Concrete kerb units — Requirements and test methods

1.2.2004

1.2.2005

EN 1340:2003/AC:2006

1.1.2007

1.1.2007

CEN

EN 1341:2012

Slabs of natural stone for external paving — Requirements and test methods

EN 1341:2001

1.9.2013

1.9.2013

CEN

EN 1342:2012

Setts of natural stone for external paving — Requirements and test methods

EN 1342:2001

1.9.2013

1.9.2013

CEN

EN 1343:2012

Kerbs of natural stone for external paving — Requirements and test methods

EN 1343:2001

1.9.2013

1.9.2013

CEN

EN 1344:2013

Clay pavers — Requirements and test methods

EN 1344:2002

8.8.2014

8.8.2016

EN 1344:2013/AC:2015

CEN

EN 1423:2012

Road marking materials — Drop on materials — Glass beads, antiskid aggregates and mixtures of the two

EN 1423:1997

1.11.2012

1.11.2012

EN 1423:2012/AC:2013

1.7.2013

1.7.2013

CEN

EN 1433:2002

Drainage channels for vehicular and pedestrian areas — Classification, design and testing requirements, marking and evaluation of conformity

1.8.2003

1.8.2004

EN 1433:2002/A1:2005

1.1.2006

1.1.2006

CEN

EN 1457-1:2012

Chimneys — Clay/ceramic flue liners — Part 1: Flue liners operating under dry conditions — Requirements and test methods

EN 1457:1999

1.11.2012

1.11.2013

CEN

EN 1457-2:2012

Chimneys — Clay/ceramic flue liners — Part 2: Flue liners operating under wet conditions — Requirements and test methods

EN 1457:1999

1.11.2012

1.11.2013

CEN

EN 1463-1:2009

Road marking materials — Retroreflecting road studs — Part 1: Initial performance requirements

EN 1463-1:1997

1.1.2010

1.1.2011

CEN

EN 1469:2015

Natural stone products — Slabs for cladding — Requirements

EN 1469:2004

8.4.2016

8.4.2017

CEN

EN 1504-2:2004

Products and systems for the protection and repair of concrete structures — Definitions, requirements, quality control and evaluation of conformity — Part 2: Surface protection systems for concrete

1.9.2005

1.1.2009

CEN

EN 1504-3:2005

Products and systems for the protection and repair of concrete structures — Definitions, requirements, quality control and evaluation of conformity — Part 3: Structural and non-structural repair

1.10.2006

1.1.2009

CEN

EN 1504-4:2004

Products and systems for the protection and repair of concrete structures — Definitions, requirements, quality control and evaluation of conformity — Part 4: Structural bonding

1.9.2005

1.1.2009

CEN

EN 1504-5:2004

Products and systems for the protection and repair of concrete structures — Definitions, requirements, quality control and evaluation of conformity — Part 5: Concrete injection

1.10.2005

1.1.2009

CEN

EN 1504-6:2006

Products and systems for the protection and repair of concrete structures — Definitions, requirements, quality control and evaluation of conformity — Part 6: Anchoring of reinforcing steel bar

1.6.2007

1.1.2009

CEN

EN 1504-7:2006

Products and systems for the protection and repair of concrete structures — Definitions, requirements, quality control and evaluation of conformity — Part 7: Reinforcement corrosion protection

1.6.2007

1.1.2009

CEN

EN 1520:2011

Prefabricated reinforced components of lightweight aggregate concrete with open structure with structural or non-structural reinforcement

EN 1520:2002

1.1.2012

1.1.2013

CEN

EN 1748-1-2:2004

Glass in building — Special basic products — Borosilicate glasses — Part 1-2: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 1748-2-2:2004

Glass in building — Special basic products — Glass ceramics — Part 2-2: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 1806:2006

Chimneys — Clay/ceramic flue blocks for single wall chimneys — Requirements and test methods

1.5.2007

1.5.2008

CEN

EN 1825-1:2004

Grease separators — Part 1: Principles of design, performance and testing, marking and quality control

1.9.2005

1.9.2006

EN 1825-1:2004/AC:2006

1.1.2007

1.1.2007

CEN

EN 1856-1:2009

Chimneys — Requirements for metal chimneys — Part 1: System chimney products

EN 1856-1:2003

1.3.2010

1.3.2011

CEN

EN 1856-2:2009

Chimneys — Requirements for metal chimneys — Part 2: Metal flue liners and connecting flue pipes

EN 1856-2:2004

1.3.2010

1.3.2011

CEN

EN 1857:2010

Chimneys — Components — Concrete flue liners

EN 1857:2003+A1:2008

1.1.2011

1.1.2012

CEN

EN 1858:2008+A1:2011

Chimneys — Components — Concrete flue blocks

EN 1858:2008

1.4.2012

1.4.2013

CEN

EN 1863-2:2004

Glass in building — Heat strengthened soda lime silicate glass — Part 2: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 1873:2005

Prefabricated accessories for roofing — Individual roof lights of plastics — Product specification and test methods

1.10.2006

1.10.2009

CEN

EN 1916:2002

Concrete pipes and fittings, unreinforced, steel fibre and reinforced

1.8.2003

23.11.2004

EN 1916:2002/AC:2008

1.1.2009

1.1.2009

CEN

EN 1917:2002

Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

1.8.2003

23.11.2004

EN 1917:2002/AC:2008

1.1.2009

1.1.2009

CEN

EN 1935:2002

Building hardware — Single-axis hinges — Requirements and test methods

1.10.2002

1.12.2003

EN 1935:2002/AC:2003

1.1.2007

1.1.2007

CEN

EN 10025-1:2004

Hot rolled products of structural steels — Part 1: General technical delivery conditions

1.9.2005

1.9.2006

CEN

EN 10088-4:2009

Stainless steels — Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes

1.2.2010

1.2.2011

CEN

EN 10088-5:2009

Stainless steels — Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes

1.1.2010

1.1.2011

CEN

EN 10210-1:2006

Hot finished structural hollow sections of non-alloy and fine grain steels — Part 1: Technical delivery conditions

1.2.2007

1.2.2008

CEN

EN 10219-1:2006

Cold formed welded structural hollow sections of non-alloy and fine grain steels — Part 1: Technical delivery conditions

1.2.2007

1.2.2008

CEN

EN 10224:2002

Non-alloy steel tubes and fittings for the conveyance of aqueous liquids including water for human consumption — Technical delivery conditions

1.4.2006

1.4.2007

EN 10224:2002/A1:2005

1.4.2006

1.4.2007

CEN

EN 10255:2004+A1:2007

Non-Alloy steel tubes suitable for welding and threading — Technical delivery conditions

1.1.2010

1.1.2011

CEN

EN 10311:2005

Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids

1.3.2006

1.3.2007

CEN

EN 10312:2002

Welded stainless steel tubes for the conveyance of aqueous liquids including water for human consumption — Technical delivery conditions

1.4.2006

1.4.2007

EN 10312:2002/A1:2005

1.4.2006

1.4.2007

CEN

EN 10340:2007

Steel castings for structural uses

1.1.2010

1.1.2011

EN 10340:2007/AC:2008

1.1.2010

1.1.2010

CEN

EN 10343:2009

Steels for quenching and tempering for construction purposes — Technical delivery conditions

1.1.2010

1.1.2011

CEN

EN 12004:2007+A1:2012

Adhesives for tiles — Requirements, evaluation of conformity, classification and designation

EN 12004:2007

1.4.2013

1.7.2013

CEN

EN 12050-1:2001

Wastewater lifting plants for buildings and sites — Principles of construction and testing — Part 1: Lifting plants for wastewater containing faecal matter

1.11.2001

1.11.2002

CEN

EN 12050-2:2000

Wastewater lifting plants for buildings and sites — Principles of construction and testing — Part 2: Lifting plants for faecal-free wastewater

1.10.2001

1.10.2002

CEN

EN 12050-3:2000

Wastewater lifting plants for buildings and sites — Principles of construction and testing — Part 3: Lifting plants for wastewater containing faecal matter for limited applications

1.10.2001

1.10.2002

CEN

EN 12050-4:2000

Wastewater lifting plants for buildings and sites — Principles of construction and testing — Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter

1.10.2001

1.10.2002

CEN

EN 12057:2004

Natural stone products — Modular tiles — Requirements

1.9.2005

1.9.2006

CEN

EN 12058:2004

Natural stone products — Slabs for floors and stairs — Requirements

1.9.2005

1.9.2006

CEN

EN 12094-1:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 1: Requirements and test methods for electrical automatic control and delay devices

1.2.2004

1.5.2006

CEN

EN 12094-2:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 2: Requirements and test methods for non-electrical automatic control and delay devices

1.2.2004

1.5.2006

CEN

EN 12094-3:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 3: Requirements and test methods for manual triggering and stop devices

1.1.2004

1.9.2005

CEN

EN 12094-4:2004

Fixed firefighting systems — Components for gas extinguishing systems — Part 4: Requirements and test methods for container valve assemblies and their actuators

1.5.2005

1.8.2007

CEN

EN 12094-5:2006

Fixed firefighting systems — Components for gas extinguishing systems — Part 5: Requirements and test methods for high and low pressure selector valves and their actuators

EN 12094-5:2000

1.2.2007

1.5.2009

CEN

EN 12094-6:2006

Fixed firefighting systems — Components for gas extinguishing systems — Part 6: Requirements and test methods for non-electrical disable devices

EN 12094-6:2000

1.2.2007

1.5.2009

CEN

EN 12094-7:2000

Fixed firefighting systems — Components for gas extinguishing systems — Part 7: Requirements and test methods for nozzles for CO2 systems

1.10.2001

1.4.2004

EN 12094-7:2000/A1:2005

1.11.2005

1.11.2006

CEN

EN 12094-8:2006

Fixed firefighting systems — Components for gas extinguishing systems — Part 8: Requirements and test methods for connectors

1.2.2007

1.5.2009

CEN

EN 12094-9:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 9: Requirements and test methods for special fire detectors

1.1.2004

1.9.2005

CEN

EN 12094-10:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 10: Requirements and test methods for pressure gauges and pressure switches

1.2.2004

1.5.2006

CEN

EN 12094-11:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 11: Requirements and test methods for mechanical weighing devices

1.1.2004

1.9.2005

CEN

EN 12094-12:2003

Fixed firefighting systems — Components for gas extinguishing systems — Part 12: Requirements and test methods for pneumatic alarm devices

1.1.2004

1.9.2005

CEN

EN 12094-13:2001

Fixed firefighting systems — Components for gas extinguishing systems — Part 13: Requirements and test methods for check valves and non-return valves

1.1.2002

1.4.2004

EN 12094-13:2001/AC:2002

1.1.2010

1.1.2010

CEN

EN 12101-1:2005

Smoke and heat control systems — Part 1: Specification for smoke barriers

1.6.2006

1.9.2008

EN 12101-1:2005/A1:2006

1.12.2006

1.9.2008

CEN

EN 12101-2:2003

Smoke and heat control systems — Part 2: Specification for natural smoke and heat exhaust ventilators

1.4.2004

1.9.2006

CEN

EN 12101-3:2015

Smoke and heat control systems — Part 3: Specification for powered smoke and heat control ventilators (Fans)

EN 12101-3:2002

8.4.2016

8.4.2017

CEN

EN 12101-6:2005

Smoke and heat control systems — Part 6: Specification for pressure differential systems — Kits

1.4.2006

1.4.2007

EN 12101-6:2005/AC:2006

1.1.2007

1.1.2007

CEN

EN 12101-7:2011

Smoke and heat control systems — Part 7: Smoke duct sections

1.2.2012

1.2.2013

CEN

EN 12101-8:2011

Smoke and heat control systems — Part 8: Smoke control dampers

1.2.2012

1.2.2013

CEN

EN 12101-10:2005

Smoke and heat control systems — Part 10: Power supplies

1.10.2006

1.5.2012

EN 12101-10:2005/AC:2007

1.1.2008

1.1.2008

CEN

EN 12150-2:2004

Glass in building — Thermally toughened soda lime silicate safety glass — Part 2: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 12209:2003

Building hardware — Locks and latches — Mechanically operated locks, latches and locking plates — Requirements and test methods

1.12.2004

1.6.2006

EN 12209:2003/AC:2005

1.6.2006

1.6.2006

CEN

EN 12259-1:1999 + A1:2001

Fixed firefighting systems — Components for sprinkler and water spray systems — Part 1: Sprinklers

1.4.2002

1.9.2005

EN 12259-1:1999 + A1:2001/A2:2004

1.3.2005

1.3.2006

EN 12259-1:1999 + A1:2001/A3:2006

1.11.2006

1.11.2007

CEN

EN 12259-2:1999

Fixed firefighting systems — Components for sprinkler and water spray systems — Part 2: Wet alarm valve assemblies

1.1.2002

1.8.2007

EN 12259-2:1999/A1:2001

1.1.2002

1.8.2007

EN 12259-2:1999/AC:2002

1.6.2005

1.6.2005

EN 12259-2:1999/A2:2005

1.9.2006

1.8.2007

CEN

EN 12259-3:2000

Fixed firefighting systems — Components for automatic sprinkler and water spray systems — Part 3: Dry alarm valve assemblies

1.1.2002

1.8.2007

EN 12259-3:2000/A1:2001

1.1.2002

1.8.2007

EN 12259-3:2000/A2:2005

1.9.2006

1.8.2007

CEN

EN 12259-4:2000

Fixed firefighting systems — Components for sprinkler and water spray systems — Part 4: Water motor alarms

1.1.2002

1.4.2004

EN 12259-4:2000/A1:2001

1.1.2002

1.4.2004

CEN

EN 12259-5:2002

Fixed firefighting systems — Components for sprinkler and water spray systems — Part 5: Water flow detectors

1.7.2003

1.9.2005

CEN

EN 12271:2006

Surface dressing — Requirements

1.1.2008

1.1.2011

CEN

EN 12273:2008

Slurry surfacing — Requirements

1.1.2009

1.1.2011

CEN

EN 12285-2:2005

Workshop fabricated steel tanks — Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids

1.1.2006

1.1.2008

CEN

EN 12326-1:2014

Slate and stone for discontinuous roofing and external cladding — Part 1: Specifications for slate and carbonate slate

EN 12326-1:2004

13.2.2015

13.2.2016

CEN

EN 12337-2:2004

Glass in building — Chemically strengthened soda lime silicate glass — Part 2: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 12352:2006

Traffic control equipment — Warning and safety light devices

1.2.2007

1.2.2008

CEN

EN 12368:2006

Traffic control equipment — Signal heads

1.2.2007

1.2.2008

CEN

EN 12380:2002

Air admittance valves for drainage systems — Requirements, tests methods and evaluation of conformity

1.10.2003

1.10.2004

CEN

EN 12446:2011

Chimneys — Components — Concrete outer wall elements

EN 12446:2003

1.4.2012

1.4.2013

CEN

EN 12467:2012

Fibre-cement flat sheets — Product specification and test methods

EN 12467:2004

1.7.2013

1.7.2013

CEN

EN 12566-1:2000

Small wastewater treatment systems for up to 50 PT — Part 1: Prefabricated septic tanks

1.12.2004

1.12.2005

EN 12566-1:2000/A1:2003

1.12.2004

1.12.2005

CEN

EN 12566-3:2005+A2:2013

Small wastewater treatment systems for up to 50 PT — Part 3: Packaged and/or site assembled domestic wastewater treatment plants

EN 12566-3:2005+A1:2009

8.8.2014

8.8.2015

CEN

EN 12566-4:2007

Small wastewater treatment systems for up to 50 PT — Part 4: Septic tanks assembled in situ from prefabricated kits

1.1.2009

1.1.2010

CEN

EN 12566-6:2013

Small wastewater treatment systems for up to 50 PT — Part 6: Prefabricated treatment units for septic tank effluent

1.11.2013

1.11.2014

CEN

EN 12566-7:2013

Small wastewater treatment systems for up to 50 PT — Part 7: Prefabricated tertiary treatment units

8.8.2014

8.8.2015

CEN

EN 12591:2009

Bitumen and bituminous binders — Specifications for paving grade bitumens

1.1.2010

1.1.2011

CEN

EN 12602:2016

Prefabricated reinforced components of autoclaved aerated concrete

EN 12602:2008+A1:2013

10.3.2017

10.3.2018

CEN

EN 12620:2002+A1:2008

Aggregates for concrete

EN 12620:2002

1.1.2009

1.1.2010

CEN

EN 12676-1:2000

Anti-glare systems for roads — Part 1: Performance and characteristics

1.2.2004

1.2.2006

EN 12676-1:2000/A1:2003

1.2.2004

1.2.2006

CEN

EN 12737:2004+A1:2007

Precast concrete products — Floor slats for livestock

1.1.2009

1.1.2010

CEN

EN 12764:2004+A1:2008

Sanitary appliances — Specification for whirlpool baths

EN 12764:2004

1.1.2009

1.1.2010

CEN

EN 12794:2005+A1:2007

Precast concrete products — Foundation piles

EN 12794:2005

1.2.2008

1.2.2009

EN 12794:2005+A1:2007/AC:2008

1.8.2009

1.8.2009

CEN

EN 12809:2001

Residential independent boilers fired by solid fuel — Nominal heat output up to 50 kW — Requirements and test methods

1.7.2005

1.7.2007

EN 12809:2001/A1:2004

1.7.2005

1.7.2007

EN 12809:2001/A1:2004/AC:2007

1.1.2008

1.1.2008

EN 12809:2001/AC:2006

1.1.2008

1.1.2008

CEN

EN 12815:2001

Residential cookers fired by solid fuel — Requirements and test methods

1.7.2005

1.7.2007

EN 12815:2001/AC:2006

1.1.2007

1.1.2007

EN 12815:2001/A1:2004/AC:2007

1.1.2008

1.1.2008

EN 12815:2001/A1:2004

1.7.2005

1.7.2007

CEN

EN 12839:2012

Precast concrete products — Elements for fences

EN 12839:2001

1.10.2012

1.10.2013

CEN

EN 12843:2004

Precast concrete products — Masts and poles

1.9.2005

1.9.2007

CEN

EN 12859:2011

Gypsum blocks — Definitions, requirements and test methods

EN 12859:2008

1.12.2011

1.12.2012

CEN

EN 12860:2001

Gypsum based adhesives for gypsum blocks — Definitions, requirements and test methods

1.4.2002

1.4.2003

EN 12860:2001/AC:2002

1.1.2010

1.1.2010

CEN

EN 12878:2005

Pigments for the colouring of building materials based on cement and/or lime — Specifications and methods of test

1.3.2006

1.3.2007

EN 12878:2005/AC:2006

1.1.2007

1.1.2007

CEN

EN 12899-1:2007

Fixed, vertical road traffic signs — Part 1: Fixed signs

1.1.2009

1.1.2013

CEN

EN 12899-2:2007

Fixed, vertical road traffic signs — Part 2: Transilluminated traffic bollards (TTB)

1.1.2009

1.1.2013

CEN

EN 12899-3:2007

Fixed, vertical road traffic signs — Part 3: Delineator posts and retroreflectors

1.1.2009

1.1.2013

CEN

EN 12951:2004

Prefabricated accessories for roofing — Permanently fixed roof ladders — Product specification and test methods

1.9.2005

1.9.2006

CEN

EN 12966-1:2005+A1:2009

Road vertical signs — Variable message traffic signs — Part 1: Product standard

1.8.2010

1.8.2010

CEN

EN 13024-2:2004

Glass in building — Thermally toughened borosilicate safety glass — Part 2: Evaluation of conformity/Product standard

1.9.2005

1.9.2006

CEN

EN 13043:2002

Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas

1.7.2003

1.6.2004

EN 13043:2002/AC:2004

1.6.2006

1.6.2006

CEN

EN 13055-1:2002

Lightweight aggregates — Part 1: Lightweight aggregates for concrete, mortar and grout

1.3.2003

1.6.2004

EN 13055-1:2002/AC:2004

1.1.2010

1.1.2010

CEN

EN 13055-2:2004

Lightweight aggregates — Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications

1.5.2005

1.5.2006

CEN

EN 13063-1:2005+A1:2007

Chimneys — System chimneys with clay/ceramic flue liners — Part 1: Requirements and test methods for sootfire resistance

EN 13063-1:2005

1.5.2008

1.5.2009

CEN

EN 13063-2:2005+A1:2007

Chimneys — System chimneys with clay/ceramic flue liners — Part 2: Requirements and test methods under wet conditions

EN 13063-2:2005

1.5.2008

1.5.2009

CEN

EN 13063-3:2007

Chimneys — System chimneys with clay/ceramic flue liners — Part 3: Requirements and test methods for air flue system chimneys

1.5.2008

1.5.2009

CEN

EN 13069:2005

Chimneys — Clay/ceramic outer walls for system chimneys — Requirements and test methods

1.5.2006

1.5.2007

CEN

EN 13084-5:2005

Free-standing chimneys — Part 5: Material for brick liners — Product specifications

1.4.2006

1.4.2007

EN 13084-5:2005/AC:2006

1.1.2007

1.1.2007

CEN

EN 13084-7:2012

Free-standing chimneys — Part 7: Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and steel liners

EN 13084-7:2005

1.9.2013

1.9.2013

CEN

EN 13101:2002

Steps for underground man entry chambers — Requirements, marking, testing and evaluation of conformity

1.8.2003

1.8.2004

CEN

EN 13108-1:2006

Bituminous mixtures — Material specifications — Part 1: Asphalt Concrete

1.3.2007

1.3.2008

EN 13108-1:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13108-2:2006

Bituminous mixtures — Material specifications — Part 2: Asphalt Concrete for very thin layers

1.3.2007

1.3.2008

EN 13108-2:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13108-3:2006

Bituminous mixtures — Material specifications — Part 3: Soft Asphalt

1.3.2007

1.3.2008

EN 13108-3:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13108-4:2006

Bituminous mixtures — Material specifications — Part 4: Hot Rolled Asphalt

1.3.2007

1.3.2008

EN 13108-4:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13108-5:2006

Bituminous mixtures — Material specifications — Part 5: Stone Mastic Asphalt

1.3.2007

1.3.2008

EN 13108-5:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13108-6:2006

Bituminous mixtures — Material specifications — Part 6: Mastic Asphalt

1.3.2007

1.3.2008

EN 13108-6:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13108-7:2006

Bituminous mixtures — Material specifications — Part 7: Porous Asphalt

1.3.2007

1.3.2008

EN 13108-7:2006/AC:2008

1.1.2009

1.1.2009

CEN

EN 13139:2002

Aggregates for mortar

1.3.2003

1.6.2004

EN 13139:2002/AC:2004

1.1.2010

1.1.2010

CEN

EN 13160-1:2003

Leak detection systems — Part 1: General principles

1.3.2004

1.3.2005

CEN

EN 13162:2012+A1:2015

Thermal insulation products for buildings — Factory made mineral wool (MW) products — Specification

EN 13162:2012

10.7.2015

10.7.2016

CEN

EN 13163:2012+A1:2015

Thermal insulation products for buildings — Factory made expanded polystyrene (EPS) products — Specification

EN 13163:2012

10.7.2015

10.7.2016

CEN

EN 13164:2012+A1:2015

Thermal insulation products for buildings — Factory made extruded polystyrene foam (XPS) products — Specification

EN 13164:2012

10.7.2015

10.7.2016

CEN

EN 13165:2012+A2:2016

Thermal insulation products for buildings — Factory made rigid polyurethane foam (PU) products — Specification

EN 13165:2012+A1:2015

14.10.2016

14.10.2017

CEN

EN 13166:2012+A2:2016

Thermal insulation products for buildings — Factory made phenolic foam (PF) products — Specification

EN 13166:2012+A1:2015

14.10.2016

14.10.2017

CEN

EN 13167:2012+A1:2015

Thermal insulation products for buildings — Factory made cellular glass (CG) products — Specification

EN 13167:2012

10.7.2015

10.7.2016

CEN

EN 13168:2012+A1:2015

Thermal insulation products for buildings — Factory made wood wool (WW) products — Specification

EN 13168:2012

10.7.2015

10.7.2016

CEN

EN 13169:2012+A1:2015

Thermal insulation products for buildings — Factory made expanded perlite board (EPB) products — Specification

EN 13169:2012

10.7.2015

10.7.2016

CEN

EN 13170:2012+A1:2015

Thermal insulation products for buildings — Factory made products of expanded cork (ICB) — Specification

EN 13170:2012

10.7.2015

10.7.2016

CEN

EN 13171:2012+A1:2015

Thermal insulation products for buildings — Factory made wood fibre (WF) products — Specification

EN 13171:2012

10.7.2015

10.7.2016

CEN

EN 13224:2011

Precast concrete products — Ribbed floor elements

EN 13224:2004+A1:2007

1.8.2012

1.8.2013

CEN

EN 13225:2013

Precast concrete products — Linear structural elements

EN 13225:2004

8.8.2014

8.8.2015

CEN

EN 13229:2001

Inset appliances including open fires fired by solid fuels — Requirements and test methods

1.7.2005

1.7.2007

EN 13229:2001/AC:2006

1.7.2007

1.7.2007

EN 13229:2001/A2:2004/AC:2007

1.1.2008

1.1.2008

EN 13229:2001/A2:2004

1.7.2005

1.7.2007

EN 13229:2001/A1:2003

1.6.2006

1.6.2007

CEN

EN 13240:2001

Roomheaters fired by solid fuel — Requirements and test methods

1.7.2005

1.7.2007

EN 13240:2001/A2:2004

1.7.2005

1.7.2007

EN 13240:2001/AC:2006

1.1.2007

1.1.2007

EN 13240:2001/A2:2004/AC:2007

1.1.2008

1.1.2008

CEN

EN 13241:2003+A2:2016

Industrial, commercial, garage doors and gates — Product standard, performance characteristics

EN 13241-1:2003+A1:2011

1.11.2016

1.11.2019

CEN

EN 13242:2002+A1:2007

Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction

EN 13242:2002

1.1.2009

1.1.2010

CEN

EN 13245-2:2008

Plastics — Unplasticised poly(vinyl chloride) (PVC-U) profiles for building applications — Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes

1.7.2010

1.7.2012

EN 13245-2:2008/AC:2009

1.7.2010

1.7.2010

CEN

EN 13249:2016

Geotextiles and geotextile-related products — Characteristics required for use in the construction of roads and other trafficked areas (excluding railways and asphalt inclusion)

EN 13249:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13250:2016

Geotextiles and geotextile-related products — Characteristics required for use in the construction of railways

EN 13250:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13251:2016

Geotextiles and geotextile-related products — Characteristics required for use in earthworks, foundations and retaining structures

EN 13251:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13252:2016

Geotextiles and geotextile-related products — Characteristics required for use in drainage systems

EN 13252:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13253:2016

Geotextiles and geotextile-related products — Characteristics required for use in erosion control works (coastal protection, bank revetments)

EN 13253:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13254:2016

Geotextiles and geotextile-related products — Characteristics required for the use in the construction of reservoirs and dams

EN 13254:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13255:2016

Geotextiles and geotextile-related products — Characteristics required for use in the construction of canals

EN 13255:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13256:2016

Geotextiles and geotextile-related products — Characteristics required for use in the construction of tunnels and underground structures

EN 13256:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13257:2016

Geotextiles and geotextile-related products — Characteristics required for use in solid waste disposals

EN 13257:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13263-1:2005+A1:2009

Silica fume for concrete — Part 1: Definitions, requirements and conformity criteria

EN 13263-1:2005

1.1.2010

1.1.2011

CEN

EN 13265:2016

Geotextiles and geotextile-related products — Characteristics required for use in liquid waste containment projects

EN 13265:2014+A1:2015

10.3.2017

10.3.2018

CEN

EN 13279-1:2008

Gypsum binders and gypsum plasters — Part 1: Definitions and requirements

EN 13279-1:2005

1.10.2009

1.10.2010

CEN

EN 13282-1:2013

Hydraulic road binders — Part 1: Rapid hardening hydraulic road binders — Composition, specifications and conformity criteria

1.11.2013

1.11.2014

CEN

EN 13310:2003

Kitchen sinks — Functional requirements and test methods

1.2.2004

1.2.2006

CEN

EN 13341:2005+A1:2011

Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels — Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 — Requirements and test methods

EN 13341:2005

1.10.2011

1.10.2011

CEN

EN 13361:2004

Geosynthetic barriers — Characteristics required for use in the construction of reservoirs and dams

1.9.2005

1.9.2006

EN 13361:2004/A1:2006

1.6.2007

1.6.2008

CEN

EN 13362:2005

Geosynthetic Barriers — Characteristics required for use in the construction of canals

1.2.2006

1.2.2007

CEN

EN 13383-1:2002

Armourstone — Part 1: Specification

1.3.2003

1.6.2004

EN 13383-1:2002/AC:2004

1.1.2010

1.1.2010

The threshold level for density set in Clause 5.2 (of EN 13383-1:2002) is excluded from the scope of the reference. (COM Decision 2016/1610)

CEN

EN 13407:2006

Wall-hung urinals — Functional requirements and test methods

1.1.2008

1.1.2009

CEN

EN 13450:2002

Aggregates for railway ballast

1.10.2003

1.6.2004

EN 13450:2002/AC:2004

1.1.2007

1.1.2007

CEN

EN 13454-1:2004

Binders, composite binders and factory made mixtures for floor screeds based on calcium sulphate — Part 1: Definitions and requirements

1.7.2005

1.7.2006

CEN

EN 13479:2004

Welding consumables — General product standard for filler metals and fluxes for fusion welding of metallic materials

1.10.2005

1.10.2006

CEN

EN 13491:2004

Geosynthetic barriers — Characteristics required for use as a fluid barrier in the construction of tunnels and underground structures

1.9.2005

1.9.2006

EN 13491:2004/A1:2006

1.6.2007

1.6.2008

CEN

EN 13492:2004

Geosynthetic barriers — Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment

1.9.2005

1.9.2006

EN 13492:2004/A1:2006

1.6.2007

1.6.2008

CEN

EN 13493:2005

Geosynthetic barriers — Characteristics required for use in the construction of solid waste storage and disposal sites

1.3.2006

1.3.2007

CEN

EN 13502:2002

Chimneys — Requirements and test methods for clay/ceramic flue terminals

1.8.2003

1.8.2004

CEN

EN 13561:2004+A1:2008

External blinds — Performance requirements including safety

EN 13561:2004

1.8.2009

1.8.2010

CEN

EN 13564-1:2002

Anti-flooding devices for buildings — Part 1: Requirements

1.5.2003

1.5.2004

CEN

EN 13616:2004

Overfill prevention devices for static tanks for liquid petroleum fuels

1.5.2005

1.5.2006

EN 13616:2004/AC:2006

1.6.2006

1.6.2006

CEN

EN 13658-1:2005

Metal lath and beads — Definitions, requirements and test methods — Part 1: Internal plastering

1.3.2006

1.3.2007

CEN

EN 13658-2:2005

Metal lath and beads — Definitions, requirements and test methods — Part 2: External rendering

1.3.2006

1.3.2007

CEN

EN 13659:2004+A1:2008

Shutters — Performance requirements including safety

EN 13659:2004

1.8.2009

1.8.2010

CEN

EN 13693:2004+A1:2009

Precast concrete products — Special roof elements

EN 13693:2004

1.5.2010

1.5.2011

CEN

EN 13707:2004+A2:2009

Flexible sheets for waterproofing — Reinforced bitumen sheets for roof waterproofing — Definitions and characteristics

1.4.2010

1.10.2010

CEN

EN 13747:2005+A2:2010

Precast concrete products — Floor plates for floor systems

EN 13747:2005+A1:2008

1.1.2011

1.1.2011

CEN

EN 13748-1:2004

Terrazzo tiles — Part 1: Terrazzo tiles for internal use

1.6.2005

1.10.2006

EN 13748-1:2004/A1:2005

1.4.2006

1.10.2006

EN 13748-1:2004/AC:2005

1.6.2005

1.6.2005

CEN

EN 13748-2:2004

Terrazzo tiles — Part 2: Terrazzo tiles for external use

1.4.2005

1.4.2006

CEN

EN 13808:2013

Bitumen and bituminous binders — Framework for specifying cationic bituminous emulsions

EN 13808:2005

8.8.2014

8.8.2015

CEN

EN 13813:2002

Screed material and floor screeds — Screed material — Properties and requirements

1.8.2003

1.8.2004

CEN

EN 13815:2006

Fibrous gypsum plaster casts — Definitions, requirements and test methods

1.6.2007

1.6.2008

CEN

EN 13830:2003

Curtain walling — Product standard

1.12.2004

1.12.2005

CEN

EN 13859-1:2010

Flexible sheets for waterproofing — Definitions and characteristics of underlays — Part 1: Underlays for discontinuous roofing

1.4.2011

1.4.2012

CEN

EN 13859-2:2010

Flexible sheets for waterproofing — Definitions and characteristics of underlays — Part 2: Underlays for walls

1.4.2011

1.4.2012

CEN

EN 13877-3:2004

Concrete pavements — Part 3: Specifications for dowels to be used in concrete pavements

1.9.2005

1.9.2006

CEN

EN 13915:2007

Prefabricated gypsum plasterboard panels with a cellular paperboard core — Definitions, requirements and test methods

1.6.2008

1.6.2009

CEN

EN 13924:2006

Bitumen and bituminous binders — Specifications for hard paving grade bitumens

1.1.2010

1.1.2011

EN 13924:2006/AC:2006

1.1.2010

1.1.2010

CEN

EN 13950:2014

Gypsum board thermal/acoustic insulation composite panels — Definitions, requirements and test methods

EN 13950:2005

13.2.2015

13.2.2016

CEN

EN 13956:2012

Flexible sheets for waterproofing — Plastic and rubber sheets for roof waterproofing — Definitions and characteristics

EN 13956:2005

1.10.2013

1.10.2013

CEN

EN 13963:2005

Jointing materials for gypsum plasterboards — Definitions, requirements and test methods

1.3.2006

1.3.2007

EN 13963:2005/AC:2006

1.1.2007

1.1.2007

CEN

EN 13964:2014

Suspended ceilings — Requirements and test methods

EN 13964:2004

8.4.2016

8.4.2017

CEN

EN 13967:2012

Flexible sheets for waterproofing — Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet — Definitions and characteristics

EN 13967:2004

1.3.2013

1.7.2013

CEN

EN 13969:2004

Flexible sheets for waterproofing — Bitumen damp proof sheets including bitumen basement tanking sheets — Definitions and characteristics

1.9.2005

1.9.2006

EN 13969:2004/A1:2006

1.1.2008

1.1.2009

CEN

EN 13970:2004

Flexible sheets for waterproofing — Bitumen water vapour control layers — Definitions and characteristics

1.9.2005

1.9.2006

EN 13970:2004/A1:2006

1.1.2008

1.1.2009

CEN

EN 13978-1:2005

Precast concrete products — Precast concrete garages — Part 1: Requirements for reinforced garages monolithic or consisting of single sections with room dimensions

1.3.2006

1.3.2008

CEN

EN 13984:2013

Flexible sheets for waterproofing — Plastic and rubber vapour control layers — Definitions and characteristics

EN 13984:2004

1.11.2013

1.11.2013

CEN

EN 13986:2004+A1:2015

Wood-based panels for use in construction — Characteristics, evaluation of conformity and marking

EN 13986:2004

13.11.2015

13.11.2016

CEN

EN 14016-1:2004

Binders for magnesite screeds — Caustic magnesia and magnesium chloride — Part 1: Definitions, requirements

1.12.2004

1.12.2005

CEN

EN 14023:2010

Bitumen and bituminous binders — Specification framework for polymer modified bitumens

1.1.2011

1.1.2012

CEN

EN 14037-1:2016

Free hanging heating and cooling surfaces for water with a temperature below 120 oC — Part 1: Pre-fabricated ceiling mounted radiant panels for space heating — Technical specifications and requirements

EN 14037-1:2003

10.3.2017

10.3.2018

CEN

EN 14041:2004

Resilient, textile and laminate floor coverings — Essential characteristics

1.1.2006

1.1.2007

EN 14041:2004/AC:2006

1.1.2007

1.1.2007

CEN