Choose the experimental features you want to try

This document is an excerpt from the EUR-Lex website

Document 02000L0053-20171206

Consolidated text: Directive 2000/53/EC of the European Parliament and of the Council of 18 September 2000 on end-of life vehicles

ELI: http://data.europa.eu/eli/dir/2000/53/2017-12-06

02000L0053 — EN — 06.12.2017 — 012.001


This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document

►B

DIRECTIVE 2000/53/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

of 18 September 2000

on end-of life vehicles

(OJ L 269 21.10.2000, p. 34)

Amended by:

 

 

Official Journal

  No

page

date

 M1

COMMISSION DECISION 2002/525/EC of 27 June 2002

  L 170

81

29.6.2002

 M2

COMMISSION DECISION 2005/63/EC of 24 January 2005

  L 25

73

28.1.2005

 M3

COMMISSION DECISION 2005/438/EC of 10 June 2005

  L 152

19

15.6.2005

 M4

COUNCIL DECISION 2005/673/EC of 20 September 2005

  L 254

69

30.9.2005

►M5

DIRECTIVE 2008/33/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 11 March 2008

  L 81

62

20.3.2008

 M6

COMMISSION DECISION 2008/689/EC of 1 August 2008

  L 225

10

23.8.2008

►M7

DIRECTIVE 2008/112/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL Text with EEA relevance of 16 December 2008

  L 345

68

23.12.2008

 M8

COMMISSION DECISION 2010/115/EU of 23 February 2010

  L 48

12

25.2.2010

 M9

COMMISSION DIRECTIVE 2011/37/EU Text with EEA relevance of 30 March 2011

  L 85

3

31.3.2011

 M10

COMMISSION DIRECTIVE 2013/28/EU Text with EEA relevance of 17 May 2013

  L 135

14

22.5.2013

 M11

COMMISSION DIRECTIVE (EU) 2016/774 Text with EEA relevance of 18 May 2016

  L 128

4

19.5.2016

►M12

COMMISSION DIRECTIVE (EU) 2017/2096 Text with EEA relevance of 15 November 2017

  L 299

24

16.11.2017




▼B

DIRECTIVE 2000/53/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

of 18 September 2000

on end-of life vehicles



Article 1

Objectives

This Directive lays down measures which aim, as a first priority, at the prevention of waste from vehicles and, in addition, at the reuse, recycling and other forms of recovery of end-of life vehicles and their components so as to reduce the disposal of waste, as well as at the improvement in the environmental performance of all of the economic operators involved in the life cycle of vehicles and especially the operators directly involved in the treatment of end-of life vehicles.

Article 2

Definitions

For the purposes of this Directive:

1. ‘vehicle’ means any vehicle designated as category M1 or N1 defined in Annex IIA to Directive 70/156/EEC, and three wheel motor vehicles as defined in Directive 92/61/EEC, but excluding motor tricycles;

2. ‘end-of life vehicle’ means a vehicle which is waste within the meaning of Article 1(a) of Directive 75/442/EEC;

3. ‘producer’ means the vehicle manufacturer or the professional importer of a vehicle into a Member State;

4. ‘prevention’ means measures aiming at the reduction of the quantity and the harmfulness for the environment of end-of life vehicles, their materials and substances;

5. ‘treatment’ means any activity after the end-of life vehicle has been handed over to a facility for depollution, dismantling, shearing, shredding, recovery or preparation for disposal of the shredder wastes, and any other operation carried out for the recovery and/or disposal of the end-of life vehicle and its components;

6. ‘reuse’ means any operation by which components of end-of life vehicles are used for the same purpose for which they were conceived;

7. ‘recycling’ means the reprocessing in a production process of the waste materials for the original purpose or for other purposes but excluding energy recovery. Energy recovery means the use of combustible waste as a means to generate energy through direct incineration with or without other waste but with recovery of the heat;

8. ‘recovery’ means any of the applicable operations provided for in Annex IIB to Directive 75/442/EEC;

9. ‘disposal’ means any of the applicable operations provided for in Annex IIA to Directive 75/442/EEC;

10. ‘economic operators’ means producers, distributors, collectors, motor vehicle insurance companies, dismantlers, shredders, recoverers, recyclers and other treatment operators of end-of life vehicles, including their components and materials;

▼M7

11. ‘hazardous substance’ means any substance which fulfils the criteria for any of the following hazard classes or categories set out in Annex I of Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16 December 2008 on classification, labelling and packaging of substances and mixtures ( 1 );

(a) hazard classes 2.1 to 2.4, 2.6 and 2.7, 2.8 types A and B, 2.9, 2.10, 2.12, 2.13 categories 1 and 2, 2.14 categories 1 and 2, 2.15 types A to F;

(b) hazard classes 3.1 to 3.6, 3.7 adverse effects on sexual function and fertility or on development, 3.8 effects other than narcotic effects, 3.9 and 3.10;

(c) hazard class 4.1;

(d) hazard class 5.1;

▼B

12. ‘shredder’ means any device used for tearing into pieces or fragmenting end-of life vehicles, including for the purpose of obtaining directly reusable metal scrap;

13. ‘dismantling information’ means all information required for the correct and environmentally sound treatment of end-of life vehicles. It shall be made available to authorised treatment facilities by vehicle manufacturers and component producers in the form of manuals or by means of electronic media (e.g. CD-ROM, on-line services).

Article 3

Scope

1.  This Directive shall cover vehicles and end-of life vehicles, including their components and materials. Without prejudice to Article 5(4), third subparagraph, this shall apply irrespective of how the vehicle has been serviced or repaired during use and irrespective of whether it is equipped with components supplied by the producer or with other components whose fitting as spare or replacement parts accords with the appropriate Community provisions or domestic provisions.

2.  This Directive shall apply without prejudice to existing Community legislation and relevant national legislation, in particular as regards safety standards, air emissions and noise controls and the protection of soil and water.

3.  Where a producer only makes or imports vehicles that are exempt from Directive 70/156/EEC by virtue of Article 8(2)(a) thereof, Member States may exempt that producer and his vehicles from Articles 7(4), 8 and 9 of this Directive.

4.  Special-purpose vehicles as defined in the second indent of Article 4(1)(a) of Directive 70/156/EEC shall be excluded from the provisions of Article 7 of this Directive.

5.  For three-wheel motor vehicles only Articles 5(1), 5(2) and 6 of this Directive shall apply.

Article 4

Prevention

1.  In order to promote the prevention of waste Member States shall encourage, in particular:

(a) vehicle manufacturers, in liaison with material and equipment manufacturers, to limit the use of hazardous substances in vehicles and to reduce them as far as possible from the conception of the vehicle onwards, so as in particular to prevent their release into the environment, make recycling easier, and avoid the need to dispose of hazardous waste;

(b) the design and production of new vehicles which take into full account and facilitate the dismantling, reuse and recovery, in particular the recycling, of end-of life vehicles, their components and materials;

(c) vehicle manufacturers, in liaison with material and equipment manufacturers, to integrate an increasing quantity of recycled material in vehicles and other products, in order to develop the markets for recycled materials.

2.  

(a) Member States shall ensure that materials and components of vehicles put on the market after 1 July 2003 do not contain lead, mercury, cadmium or hexavalent chromium other than in cases listed in Annex II under the conditions specified therein;

(b)  ►M5  Annex II shall be amended on a regular basis, according to technical and scientific progress, in order to: ◄

(i) as necessary, establish maximum concentration values up to which the existence of the substances referred to in subparagraph (a) in specific materials and components of vehicles shall be tolerated;

(ii) exempt certain materials and components of vehicles from the provisions of subparagraph (a) if the use of these substances is unavoidable;

(iii) delete materials and components of vehicles from Annex II if the use of these substances is avoidable;

(iv) under points (i) and (ii) designate those materials and components of vehicles that can be stripped before further treatment; they shall be labelled or made identifiable by other appropriate means;

▼M5

The measures referred to in points (i) to (iv), designed to amend non-essential elements of this Directive, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 11(3).

(c) the Commission shall amend Annex II for the first time not later than 21 October 2001. In any case none of the exemptions listed therein shall be deleted from the Annex before 1 January 2003.

Article 5

Collection

1.  Member States shall take the necessary measures to ensure:

 that economic operators set up systems for the collection of all end-of life vehicles and, as far as technically feasible, of waste used parts removed when passenger cars are repaired,

 the adequate availability of collection facilities within their territory.

2.  Member States shall also take the necessary measures to ensure that all end-of life vehicles are transferred to authorised treatment facilities.

3.  Member States shall set up a system according to which the presentation of a certificate of destruction is a condition for deregistration of the end-of life vehicle. This certificate shall be issued to the holder and/or owner when the end-of life vehicle is transferred to a treatment facility. Treatment facilities, which have obtained a permit in accordance with Article 6, shall be permitted to issue a certificate of destruction. Member States may permit producers, dealers and collectors on behalf of an authorised treatment facility to issue certificates of destruction provided that they guarantee that the end-of life vehicle is transferred to an authorised treatment facility and provided that they are registered with public authorities.

Issuing the certificate of destruction by treatment facilities or dealers or collectors on behalf of an authorised treatment facility does not entitle them to claim any financial reimbursement, except in cases where this has been explicitly arranged by Member States.

Member States which do not have a deregistration system at the date of entry into force of this Directive shall set up a system according to which a certificate of destruction is notified to the relevant competent authority when the end-of life vehicle is transferred to a treatment facility and shall otherwise comply with the terms of this paragraph. Member States making use of this subparagraph shall inform the Commission of the reasons thereof.

4.  Member States shall take the necessary measures to ensure that the delivery of the vehicle to an authorised treatment facility in accordance with paragraph 3 occurs without any cost for the last holder and/or owner as a result of the vehicle's having no or a negative market value.

Member States shall take the necessary measures to ensure that producers meet all, or a significant part of, the costs of the implementation of this measure and/or take back end-of life vehicles under the same conditions as referred to in the first subparagraph.

Member States may provide that the delivery of end-of life vehicles is not fully free of charge if the end-of life vehicle does not contain the essential components of a vehicle, in particular the engine and the coachwork, or contains waste which has been added to the end-of life vehicle.

The Commission shall regularly monitor the implementation of the first subparagraph to ensure that it does not result in market distortions, and if necessary shall propose to the European Parliament and the Council an amendment thereto.

▼M5

5.  Member States shall take the necessary measures to ensure that their competent authorities mutually recognise and accept the certificates of destruction issued in other Member States in accordance with paragraph 3.

To this end, minimum requirements for the certificate of destruction shall be established. That measure, designed to amend non-essential elements of this Directive by supplementing it, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 11(3).

▼B

Article 6

Treatment

1.  Member States shall take the necessary measures to ensure that all end-of life vehicles are stored (even temporarily) and treated in accordance with the general requirements laid down in Article 4 of Directive 75/442/EEC, and in compliance with the minimum technical requirements set out in Annex I to this Directive, without prejudice to national regulations on health and environment.

2.  Member States shall take the necessary measures to ensure that any establishment or undertaking carrying out treatment operations obtains a permit from or be registered with the competent authorities, in compliance with Articles 9, 10 and 11 of Directive 75/442/EEC.

The derogation from the permit requirement referred to in Article 11(1)(b) of Directive 75/442/EEC may apply to recovery operations concerning waste of end-of life vehicles after they have been treated according to Annex 1(3) to this Directive if there is an inspection by the competent authorities before the registration. This inspection shall verify:

(a) type and quantities of waste to be treated;

(b) general technical requirements to be complied with;

(c) safety precautions to be taken,

in order to achieve the objectives referred to in Article 4 of Directive 75/442/EEC. This inspection shall take place once a year. Member States using the derogation shall send the results to the Commission.

3.  Member States shall take the necessary measures to ensure that any establishment or undertaking carrying out treatment operations fulfils at least the following obligations in accordance with Annex I:

(a) end-of life vehicles shall be stripped before further treatment or other equivalent arrangements are made in order to reduce any adverse impact on the environment. Components or materials labelled or otherwise made identifiable in accordance with Article 4(2) shall be stripped before further treatment;

(b) hazardous materials and components shall be removed and segregated in a selective way so as not to contaminate subsequent shredder waste from end-of life vehicles;

(c) stripping operations and storage shall be carried out in such a way as to ensure the suitability of vehicle components for reuse and recovery, and in particular for recycling.

Treatment operations for depollution of end-of life vehicles as referred to in Annex I(3) shall be carried out as soon as possible.

4.  Member States shall take the necessary measures to ensure that the permit or registration referred to in paragraph 2 includes all conditions necessary for compliance with the requirements of paragraphs 1, 2 and 3.

5.  Member States shall encourage establishments or undertakings, which carry out treatment operations to introduce, certified environmental management systems.

▼M5

6.  Annex I shall be amended according to technical and scientific progress. That measure, designed to amend non-essential elements of this Directive, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 11(3).

▼B

Article 7

Reuse and recovery

1.  Member States shall take the necessary measures to encourage the reuse of components which are suitable for reuse, the recovery of components which cannot be reused and the giving of preference to recycling when environmentally viable, without prejudice to requirements regarding the safety of vehicles and environmental requirements such as air emissions and noise control.

2.  Member States shall take the necessary measures to ensure that the following targets are attained by economic operators:

(a) no later than 1 January 2006, for all end-of life vehicles, the reuse and recovery shall be increased to a minimum of 85 % by an average weight per vehicle and year. Within the same time limit the reuse and recycling shall be increased to a minimum of 80 % by an average weight per vehicle and year;

for vehicles produced before 1 January 1980, Member States may lay down lower targets, but not lower than 75 % for reuse and recovery and not lower than 70 % for reuse and recycling. Member States making use of this subparagraph shall inform the Commission and the other Member States of the reasons therefor;

(b) no later than 1 January 2015, for all end-of life vehicles, the reuse and recovery shall be increased to a minimum of 95 % by an average weight per vehicle and year. Within the same time limit, the re-use and recycling shall be increased to a minimum of 85 % by an average weight per vehicle and year.

By 31 December 2005 at the latest the European Parliament and the Council shall re-examine the targets referred to in paragraph (b) on the basis of a report of the Commission, accompanied by a proposal. In its report the Commission shall take into account the development of the material composition of vehicles and any other relevant environmental aspects related to vehicles.

▼M5

Detailed rules necessary to control compliance of Member States with the targets set out in the first subparagraph shall be established. When proposing such rules, the Commission shall take into account all relevant factors, inter alia, the availability of data and the issue of exports and imports of end-of-life vehicles. Those detailed rules, designed to amend non-essential elements of this Directive by supplementing it, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 11(3).

▼B

3.  On the basis of a proposal from the Commission, the European Parliament and the Council shall establish targets for reuse and recovery and for reuse and recycling for the years beyond 2015.

4.  In order to prepare an amendment to Directive 70/156/EEC, the Commission shall promote the preparation of European standards relating to the dismantlability, recoverability and recyclability of vehicles. Once the standards are agreed, but in any case no later than by the end of 2001, the European Parliament and the Council, on the basis of a proposal from the Commission, shall amend Directive 70/156/EEC so that vehicles type-approved in accordance with that Directive and put on the market after three years after the amendment of the Directive 70/156/EEC are re-usable and/or recyclable to a minimum of 85 % by weight per vehicle and are re-usable and/or recoverable to a minimum of 95 % by weight per vehicle.

5.  In proposing the amendment to Directive 70/156/EEC relating to the ability to be dismantled, recoverability and recyclability of vehicles, the Commission shall take into account as appropriate the need to ensure that the reuse of components does not give rise to safety or environmental hazards.

Article 8

Coding standards/dismantling information

1.  Member States shall take the necessary measures to ensure that producers, in concert with material and equipment manufacturers, use component and material coding standards, in particular to facilitate the identification of those components and materials which are suitable for reuse and recovery.

▼M5

2.  The standards referred to in paragraph 1 shall be established. When proposing such standards, the Commission shall take account of the work going on in this area in the relevant international forums and contribute to this work as appropriate. That measure, designed to amend non-essential elements of this Directive by supplementing it, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 11(3).

▼B

3.  Member States shall take the necessary measures to ensure that producers provide dismantling information for each type of new vehicle put on the market within six months after the vehicle is put on the market. This information shall identify, as far as it is needed by treatment facilities in order to comply with the provisions of this Directive, the different vehicle components and materials, and the location of all hazardous substances in the vehicles, in particular with a view to the achievement of the objectives laid down in Article 7.

4.  Without prejudice to commercial and industrial confidentiality, Member States shall take the necessary measures to ensure that manufacturers of components used in vehicles make available to authorised treatment facilities, as far as it is requested by these facilities, appropriate information concerning dismantling, storage and testing of components which can be reused.

Article 9

Reporting and information

1.  At three-year intervals Member States shall send a report to the Commission on the implementation of this Directive. The report shall be drawn up on the basis of a questionnaire or outline drafted by the Commission in accordance with the procedure laid down in Article 6 of Directive 91/692/EEC ( 2 ) with a view to establishing databases on end-of life vehicles and their treatment. The report shall contain relevant information on possible changes in the structure of motor vehicle dealing and of the collection, dismantling, shredding, recovery and recycling industries, leading to any distortion of competition between or within Member States. The questionnaire or outline shall be sent to the Member States six months before the start of the period covered by the report. The report shall be made to the Commission within nine months of the end of the three-year period covered by it.

The first report shall cover the period of three years from 21 April 2002.

Based on the above information, the Commission shall publish a report on the implementation of this Directive within nine months of receiving the reports from the Member States.

▼M5

The formats relating to the database system shall be adopted in accordance with the regulatory procedure referred to in Article 11(2).

▼B

2.  Member States shall require in each case the relevant economic operators to publish information on:

 the design of vehicles and their components with a view to their recoverability and recyclability,

 the environmentally sound treatment of end-of life vehicles, in particular the removal of all fluids and dismantling,

 the development and optimisation of ways to reuse, recycle and recover end-of life vehicles and their components,

 the progress achieved with regard to recovery and recycling to reduce the waste to be disposed of and to increase the recovery and recycling rates.

The producer must make this information accessible to the prospective buyers of vehicles. It shall be included in promotional literature used in the marketing of the new vehicle.

Article 10

Implementation

1.  Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with this Directive by 21 April 2002. They shall immediately inform the Commission thereof.

When Member States adopt these measures, these shall contain a reference to this Directive or shall be accompanied by such reference on the occasion of their official publication. The methods of making such a reference shall be laid down by Member States.

2.  Member States shall communicate to the Commission the text of the main provisions of domestic law, which they adopt in the field governed by this Directive.

3.  Provided that the objectives set out in this Directive are achieved, Member States may transpose the provisions set out in Articles 4(1), 5(1), 7(1), 8(1), 8(3) and 9(2) and specify the detailed rules of implementation of Article 5(4) by means of agreements between the competent authorities and the economic sectors concerned. Such agreements shall meet the following requirements

(a) agreements shall be enforceable;

(b) agreements need to specify objectives with the corresponding deadlines;

(c) agreements shall be published in the national official journal or an official document equally accessible to the public and transmitted to the Commission;

(d) the results achieved under an agreement shall be monitored regularly, reported to the competent authorities and to the Commission and made available to the public under the conditions set out in the agreement;

(e) the competent authorities shall make provisions to examine the progress reached under an agreement;

(f) in case of non-compliance with an agreement Member States must implement the relevant provisions of this Directive by legislative, regulatory or administrative measures.

▼M5

Article 11

Committee procedure

1.  The Commission shall be assisted by the committee established by Article 18 of Directive 75/442/EEC.

2.  Where reference is made to this paragraph, Articles 5 and 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.

The period laid down in Article 5(6) of Decision 1999/468/EC shall be set at three months.

3.  Where reference is made to this paragraph, Article 5a(1) to (4) and Article 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.

▼B

Article 12

Entry into force

1.  This Directive shall enter into force on the day of its publication in the Official Journal of the European Communities.

2.  Article 5(4) shall apply:

 as from 1 July 2002 for vehicles put on the market as from this date,

 as from 1 January 2007 for vehicles put on the market before the date referred to in the first indent.

3.  Member States may apply Article 5(4) in advance of the dates set out in paragraph 2.

Article 13

Addressees

This Directive is addressed to the Member States.




ANNEX I

Minimum technical requirements for treatment in accordance with Article 6(1) and (3)

1. Sites for storage (including temporary storage) of end-of-life vehicles prior to their treatament:

 impermeable surfaces for appropriate areas with the provision of spillage collection facilities, decanters and cleanser-degeasers,

 equipment for the treatment of water, including rainwater, in compliance with health and environmental regulations.

2. Sites for treatment:

 impermeable surfaces for appropriate areas with the provision of spillage collection facilities, decanters and cleanser-degreasers,

 appropriate storage for dismantled spare parts, including impermeable storage for oil-contaminated spare parts,

 appropriate containers for storage of batteries (with electrolyte neutralisation on site or elsewhere), filters and PCB/PCT-containing condensers,

 appropriate storage tanks for the segregated storage of end-of-life vehicle fluids: fuel, motor oil, gearbox oil, transmission oil, hydraulic oil, cooling liquids, antifreeze, brake fluids, battery acids, air-conditioning system fluids and any other fluid contained in the end-of-life vehicle,

 equipment for the treatment of water, including rainwater, in compliance with health and environmental regulations,

 appropriate storage for used tyres, including the prevention of fire hazards and excessive stockpiling.

3. Treatment operations for depollution of end-of-life vehicles:

 removal of batteries and liquified gas tanks,

 removal or neutralisation of potential explosive components, (e.g. air bags),

 removal and separate collection and storage of fuel, motor oil, transmission oil, gearbox oil, hydraulic oil, cooling liquids, antifreeze, brake fluids, air-conditioning system fluids and any other fluid contained in the end-of-life vehicle, unless they are necessary for the re-use of the parts concerned,

 removal, as far as feasible, of all components identified as containing mercury.

4. Treatment operations in order to promote recycling:

 removal or catalysts,

 removal of metal components containing copper, aluminium and magnesium if these metals are not segregated in the shredding process,

 removal of tyres and large plastic components (bumpers, dashboard, fluid containers, etc), if these materials are not segregated in the shredding process in such a way that they can be effectively recycled as materials,

 removal of glass.

5. Storage operations are to be carried out avoiding damage to components containing fluids or to recoverable components and spare parts.

▼M12




ANNEX II

Materials and components exempt from Article 4(2)(a)

A maximum concentration value up to 0,1 % by weight in homogeneous material for lead, hexavalent chromium and mercury and up to 0,01 % by weight in homogeneous material for cadmium shall be tolerated.

Spare parts put on the market after 1 July 2003 which are used for vehicles put on the market before 1 July 2003, except for wheel balance weights, carbon brushes for electric motors and brake linings, shall be exempted from the provisions of Article 4(2)(a) of Directive 2000/53/EC.



Materials and components

Scope and expiry date of the exemption

To be labelled or made identifiable in accordance with Article 4(2)(b)(iv)

Lead as an alloying element

1(a).  Steel for machining purposes and batch hot dip galvanised steel components containing up to 0,35 % lead by weight

 

 

1(b).  Continuously galvanised steel sheet containing up to 0,35 % lead by weight

Vehicles type-approved before 1 January 2016 and spare parts for these vehicles

 

2(a).  Aluminium for machining purposes with a lead content up to 2 % by weight

As spare parts for vehicles put on the market before 1 July 2005

 

2(b).  Aluminium with a lead content up to 1,5 % by weight

As spare parts for vehicles put on the market before 1 July 2008

 

2(c)(i).  Aluminium alloys for machining purposes with a lead content up to 0,4 % by weight

 (1)

 

2(c)(ii).  Aluminium alloys not included in entry 2(c)(i) with a lead content up to 0,4 % by weight ((1a))

 (3)

 

3.  Copper alloys containing up to 4 % lead by weight

 (1)

 

4(a).  Bearing shells and bushes

As spare parts for vehicles put on the market before 1 July 2008

 

4(b).  Bearing shells and bushes in engines, transmissions and air conditioning compressors

As spare parts for vehicles put on the market before 1 July 2011

 

Lead and lead compounds in components

5(a).  Lead in batteries in high-voltage systems ((2a)) that are used only for propulsion in M1 and N1 vehicles

Vehicles type-approved before 1 January 2019 and spare parts for these vehicles

X

5(b).  Lead in batteries for battery applications not included in entry 5(a)

 (1)

X

6.  Vibration dampers

Vehicles type-approved before 1 January 2016 and spare parts for these vehicles

X

7(a).  Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings

As spare parts for vehicles put on the market before 1 July 2005

 

7(b).  Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings containing up to 0,5 % lead by weight

As spare parts for vehicles put on the market before 1 July 2006

 

7(c).  Bonding agents for elastomers in powertrain applications containing up to 0,5 % lead by weight

As spare parts for vehicles put on the market before 1 July 2009

 

8(a).  Lead in solders to attach electrical and electronic components to electronic circuit boards and lead in finishes on terminations of components other than electrolyte aluminium capacitors, on component pins and on electronic circuit boards

Vehicles type-approved before 1 January 2016 and spare parts for these vehicles

(6)

8(b).  Lead in solders in electrical applications other than soldering on electronic circuit boards or on glass

Vehicles type-approved before 1 January 2011 and spare parts for these vehicles

(6)

8(c).  Lead in finishes on terminals of electrolyte aluminium capacitors

Vehicles type-approved before 1 January 2013 and spare parts for these vehicles

(6)

8(d).  Lead used in soldering on glass in mass airflow sensors

Vehicles type-approved before 1 January 2015 and spare parts of such vehicles

(6)

8(e).  Lead in high melting temperature type solders (i.e. lead-based alloys containing 85 % by weight or more lead)

 (5)

(6)

8(f)(a).  Lead in compliant pin connector systems

Vehicles type-approved before 1 January 2017 and spare parts for these vehicles

(6)

8(f)(b).  Lead in compliant pin connector systems other than the mating area of vehicle harness connectors

 (5)

(6)

8(g).  Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit flip chip packages

 (5)

(6)

8(h).  Lead in solder to attach heat spreaders to the heat sink in power semiconductor assemblies with a chip size of at least 1 cm2 of projection area and a nominal current density of at least 1 A/mm2 of silicon chip area

Vehicles type-approved before 1 January 2016 and after that date as spare parts for these vehicles

(6)

8(i).  Lead in solders in electrical glazing applications on glass except for soldering in laminated glazing

Vehicles type-approved before 1 January 2016 and after that date as spare parts for these vehicles

(6)

8(j).  Lead in solders for soldering of laminated glazing

Vehicles type-approved before 1 January 2020 and after that date as spare parts for these vehicles

(6)

9.  Valve seats

As spare parts for engine types developed before 1 July 2003

 

10(a).  Electrical and electronic components which contain lead in a glass or ceramic, in a glass or ceramic matrix compound, in a glass-ceramic material, or in a glass-ceramic matrix compound.

This exemption does not cover the use of lead in:

— glass in bulbs and glaze of spark plugs,

— dielectric ceramic materials of components listed under 10(b), 10(c) and 10(d).

 

(7) (for components other than piezo in engines)

10(b).  Lead in PZT-based dielectric ceramic materials of capacitors being part of integrated circuits or discrete semiconductors

 

 

10(c).  Lead in dielectric ceramic materials of capacitors with a rated voltage of less than 125 V AC or 250 V DC

Vehicles type-approved before 1 January 2016 and spare parts for these vehicles

 

10(d).  Lead in the dielectric ceramic materials of capacitors compensating the temperature-related deviations of sensors in ultrasonic sonar systems

Vehicles type-approved before 1 January 2017 and after that date as spare parts for these vehicles

 

11.  Pyrotechnic initiators

Vehicles type-approved before 1 July 2006 and spare parts for these vehicles

 

12.  Lead-containing thermoelectric materials in automotive electrical applications to reduce CO2 emissions by recuperation of exhaust heat

Vehicles type-approved before 1 January 2019 and spare parts for these vehicles

X

Hexavalent chromium

13(a).  Corrosion preventive coatings

As spare parts for vehicles put on the market before 1 July 2007

 

13(b).  Corrosion preventive coatings related to bolt and nut assemblies for chassis applications

As spare parts for vehicles put on the market before 1 July 2008

 

14.  As an anti-corrosion agent of the carbon steel cooling system in absorption refrigerators in motor caravans up to 0,75 weight — % in the cooling solution except where the use of other cooling technologies is practicable (i.e. available on the market for the application in motor caravans) and does not lead to negative environmental, health and/or consumer safety impacts

 

X

Mercury

15(a).  Discharge lamps for headlight application

Vehicles type-approved before 1 July 2012 and spare parts for these vehicles

X

15(b).  Fluorescent tubes used in instrument panel displays

Vehicles type-approved before 1 July 2012 and spare parts for these vehicles

X

Cadmium

16.  Batteries for electrical vehicles

As spare parts for vehicles put on the market before 31 December 2008

 

(1)   This exemption shall be reviewed in 2021.

(1a)  Applies to aluminium alloys where lead is not intentionally introduced but is present due to the use of recycled aluminium.

(3)   This exemption shall be reviewed in 2024.

(2a)  Systems that have a voltage of > 75 V DC as defined in Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (OJ L 374, 27.12.2006, p. 10).

(5)   This exemption shall be reviewed in 2019.

(6)   Dismantling if, in correlation with entry 10(a), an average threshold of 60 grams per vehicle is exceeded. For the application of this clause electronic devices not installed by the manufacturer on the production line shall not be taken into account.

(7)   Dismantling if, in correlation with entries 8(a) to 8(j), an average threshold of 60 grams per vehicle is exceeded. For the application of this clause electronic devices not installed by the manufacturer on the production line shall not be taken into account.



( 1 ) OJ L 353, 31.12.2008, p. 1.

( 2 ) OJ L 377, 31.12.1991, p. 48.

Top