CN code
|
TARIC
|
Description
|
Rate of autonomous duty
|
Supplementary Unit
|
Date foreseen for mandatory review
|
1516 20 10
|
|
Hydrogenated castor oil, so called ‘opal-wax’
|
0 %
|
-
|
31.12.2023
|
ex 2818 10 11
|
10
|
Sol-Gel corundum (CAS RN 1302-74-5) with an aluminium oxide content of 99,6 % or more by weight, having a micro crystalline structure in the form of rods with an aspect ratio of 1,3 or more, but not more than 6,0
|
0 %
|
-
|
31.12.2023
|
ex 2826 90 80
|
10
|
Lithium hexafluorophosphate (1-) (CAS RN 21324-40-3)
|
0 %
|
-
|
31.12.2019
|
ex 2828 10 00
|
10
|
Calcium hypochlorite (CAS RN 7778-54-3) having an active chlorine content of 65 % or more
|
0 %
|
-
|
31.12.2023
|
ex 2905 32 00
|
10
|
(2S)-propane-1,2-diol (CAS RN 4254-15-3)
|
0 %
|
-
|
31.12.2023
|
ex 2909 30 90
|
35
|
1-Chloro-2-(4-ethoxybenzyl)-4-iodobenzene (CAS RN 1103738-29-9)
|
0 %
|
-
|
31.12.2023
|
ex 2910 90 00
|
25
|
Phenyloxirane (CAS RN 96-09-3)
|
0 %
|
-
|
31.12.2023
|
ex 2912 29 00
|
55
|
Cyclohex-3-ene-1-carbaldehyde (CAS RN 100-50-5)
|
0 %
|
-
|
31.12.2023
|
ex 2915 90 70
|
15
|
2,2-Dimethylbutanoyl chloride (CAS RN 5856-77-9)
|
0 %
|
-
|
31.12.2023
|
ex 2916 39 90
|
57
|
2-Phenylprop-2-enoic acid (CAS RN 492-38-6)
|
0 %
|
-
|
31.12.2023
|
ex 2918 30 00
|
25
|
(E)-1-ethoxy-3-oxobut-1-en-1-olate; 2-methylpropan-1-olate; titanium(4+) (CAS RN 83877-91-2)
|
0 %
|
-
|
31.12.2023
|
ex 2918 99 90
|
33
|
Vanillic Acid (CAS RN 121-34-6) containing
—
|
not more than 10 ppm of Palladium (CAS RN 7440-05-3),
|
—
|
not more than 10 ppm of bismuth (CAS RN 7440-69-9),
|
—
|
not more than 14 ppm of formaldehyde (CAS RN 50-00-0),
|
—
|
not more than 1,3 % by weight of 3,4-dihydroxybenzoic acid (CAS RN 99-50-3),
|
—
|
not more than 0,5 % by weight of vanillin (CAS RN 121-33-5)
|
|
0 %
|
-
|
31.12.2023
|
ex 2920 90 10
|
15
|
Ethyl methyl carbonate (CAS RN 623-53-0)
|
0 %
|
-
|
31.12.2019
|
ex 2920 90 10
|
25
|
Diethyl carbonate (CAS RN 105-58-8)
|
0 %
|
-
|
31.12.2019
|
ex 2920 90 10
|
35
|
Vinylene carbonate (CAS RN 872-36-6)
|
0 %
|
-
|
31.12.2019
|
ex 2920 90 70
|
20
|
Diethyl phosphorochloridate (CAS RN 814-49-3)
|
0 %
|
-
|
31.12.2023
|
ex 2921 43 00
|
70
|
5-Bromo-4-fluoro-2-methylaniline (CAS RN 627871-16-3)
|
0 %
|
-
|
31.12.2023
|
ex 2921 45 00
|
30
|
(5 or 8)-Aminonaphthalene-2-sulphonic acid (CAS RN 51548-48-2)
|
0 %
|
-
|
31.12.2023
|
ex 2921 45 00
|
80
|
2-Aminonaphthalene-1-sulphonic acid (CAS RN 81-16-3)
|
0 %
|
-
|
31.12.2023
|
ex 2921 49 00
|
35
|
2-Ethylaniline (CAS RN 578-54-1)
|
0 %
|
-
|
31.12.2023
|
ex 2922 19 00
|
55
|
3-Aminoadamantan-1-ol (CAS RN 702-82-9)
|
0 %
|
-
|
31.12.2023
|
ex 2922 29 00
|
33
|
o-Phenetidine (CAS RN 94-70-2)
|
0 %
|
-
|
31.12.2023
|
ex 2923 90 00
|
65
|
N,N,N-trimethyl-tricyclo[3.3.1.13,7]decan-1-aminium hydroxide (CAS RN 53075-09-5) in form of an aqueous solution with a content of N,N,N-trimethyl-tricyclo[3.3.1.13,7]decan-1-aminium hydroxide by weight of 17,5 % or more but not more than 27,5 %
|
0 %
|
-
|
31.12.2023
|
ex 2924 19 00
|
75
|
(S)-4-((tert-Butoxycarbonyl)amino)-2-hydroxybutanoic acid (CAS RN 207305-60-0)
|
0 %
|
-
|
31.12.2023
|
ex 2924 29 70
|
67
|
N,N'-(2,5-Dichloro-1,4-phenylene)bis[3-oxobutyramide] (CAS RN 42487-09-2)
|
0 %
|
-
|
31.12.2023
|
ex 2924 29 70
|
70
|
N-[(benzyloxy)carbonyl]glycyl-N-[(2S)-1-{4-[(tert-butoxycarbonyl)oxy]phenyl}-3-hydroxypropan-2-yl]-L-alaninamide
|
0 %
|
-
|
31.12.2023
|
ex 2926 90 70
|
60
|
Cyfluthrin (ISO) (CAS RN 68359-37-5) or beta-cyfluthrin (ISO) (CAS RN 1820573-27-0) with a purity by weight of 95 % or more
|
0 %
|
-
|
31.12.2019
|
ex 2930 90 98
|
38
|
Allyl isothiocyanate (CAS RN 57-06-7)
|
0 %
|
-
|
31.12.2023
|
ex 2930 90 98
|
50
|
3-Mercaptopropionic acid (CAS RN 107-96-0)
|
0 %
|
-
|
31.12.2023
|
ex 2932 19 00
|
65
|
Tefuryltrione (ISO) (CAS RN 473278-76-1)
|
0 %
|
-
|
31.12.2023
|
ex 2932 20 90
|
75
|
3-Acetyl-6-methyl-2H-pyran-2, 4(3H)-dione (CAS RN 520-45-6)
|
0 %
|
-
|
31.12.2023
|
ex 2932 99 00
|
27
|
(2-Butyl-3-benzofuranyl)(4-hydroxy-3,5-diiodophenyl)methanone (CAS RN 1951-26-4)
|
0 %
|
-
|
31.12.2023
|
ex 2933 19 90
|
65
|
4-Bromo-1-(1-ethoxyethyl)-1H-pyrazole (CAS RN 1024120-52-2)
|
0 %
|
-
|
31.12.2023
|
ex 2933 39 99
|
56
|
2,5-Dichloro-4,6-dimethylnicotinonitrile (CAS RN 91591-63-8)
|
0 %
|
-
|
31.12.2023
|
ex 2933 39 99
|
59
|
Chlorpyrifos-Methyl (ISO) (CAS RN 5598-13-0)
|
0 %
|
-
|
31.12.2023
|
ex 2933 39 99
|
61
|
6-Bromopyridin-2-amine (CAS RN 19798-81-3)
|
0 %
|
-
|
31.12.2023
|
ex 2933 39 99
|
62
|
Ethyl 2,6-Dichloronicotinate (CAS RN 58584-86-4)
|
0 %
|
-
|
31.12.2023
|
ex 2933 39 99
|
64
|
Methyl 1-(3-chloropyridin-2-yl)-3-hydroxymethyl-1H-pyrazole-5-carboxylate (CAS RN 960316-73-8)
|
0 %
|
-
|
31.12.2023
|
ex 2933 39 99
|
68
|
1-(3-Chloropyridin-2-yl)-3-[[5-(trifluoromethyl)-2H-tetrazol-2-yl]methyl]-1H-pyrazole-5-carboxylic acid (CAS RN 1352319-02-8) with a purity by weight of 85 % or more
|
0 %
|
-
|
31.12.2023
|
ex 2933 49 90
|
80
|
Ethyl 6,7,8-trifluoro-1-[formyl(methyl)amino]-4-oxo-1,4-dihydroquinoline-3-carboxylate (CAS RN 100276-65-1)
|
0 %
|
-
|
31.12.2020
|
ex 2933 54 00
|
10
|
5,5 '-(1,2-diazenediyl)bis [2,4,6 (1H, 3H, 5H)-pyrimidinetrione] (CAS RN 25157-64-6)
|
0 %
|
-
|
31.12.2023
|
ex 2933 59 95
|
63
|
1-(3-Chlorophenyl) piperazine (CAS RN 6640-24-0)
|
0 %
|
-
|
31.12.2023
|
ex 2933 69 80
|
27
|
Troclosene sodium dihydrate (INNM) (CAS RN 51580-86-0)
|
0 %
|
-
|
31.12.2023
|
ex 2933 99 80
|
58
|
Ipconazole (ISO) (CAS RN 125225-28-7) with a purity by weight of 90 % or more
|
0 %
|
-
|
31.12.2023
|
ex 2933 99 80
|
59
|
Hydrates of Hydroxybenzotriazole (CAS RN 80029-43-2 and CAS RN 123333-53-9)
|
0 %
|
-
|
31.12.2023
|
ex 2933 99 80
|
61
|
(1R,5S)-8-Benzyl-8-azabicyclo(3.2.1)octan-3-one hydrochloride (CAS RN 83393-23-1)
|
0 %
|
-
|
31.12.2023
|
ex 2933 99 80
|
63
|
L-Prolinamide (CAS RN 7531-52-4)
|
0 %
|
-
|
31.12.2023
|
ex 2933 99 80
|
68
|
5-((1S,2S)-2-((2R,6S,9S,11R,12R,14aS,15S,16S,20R,23S,25aR)-9-amino-20-((R)-3-amino-1-hydroxy-3-oxopropyl)-2,11,12,15-tetrahydroxy-6-((R)-1-hydroxyethyl)-16-methyl-5,8,14,19,22,25-hexaoxotetracosahydro-1H-dipyrrolo[2,1-c:2',1'-l][1,4,7,10,13,16]hexaazacyclohenicosin-23-yl)-1,2-dihydroxyethyl)-2-hydroxyphenyl hydrogen sulphate (CAS RN 168110-44-9)
|
0 %
|
-
|
31.12.2023
|
ex 2934 99 90
|
78
|
[(3aS,5R,6S,6aS)-6-Hydroxy-2,2-dimethyltetrahydrofuro[2,3-d][1,3]dioxol-5-yl] (morpholino)methanone (CAS RN 1103738-19-7)
|
0 %
|
-
|
31.12.2023
|
ex 2934 99 90
|
80
|
2-(dimethylamino)-2-[(4-methylphenyl)methyl]-1-[4-(morpholin-4-yl)phenyl]butan-1-one (CAS RN 119344-86-4)
|
0 %
|
-
|
31.12.2023
|
ex 2935 90 90
|
33
|
4-Chloro-3-pyridinesulphonamide (CAS RN 33263-43-3)
|
0 %
|
-
|
31.12.2023
|
ex 2935 90 90
|
37
|
1,3-Dimethyl-1H-pyrazole-4-sulfonamide (CAS RN 88398-53-2)
|
0 %
|
-
|
31.12.2023
|
ex 2935 90 90
|
60
|
4-[(3-Methylphenyl)amino]pyridine-3-sulphonamide (CAS RN72811-73-5)
|
0 %
|
-
|
31.12.2023
|
ex 3204 17 00
|
31
|
Colourant C.I. Pigment Red 63:1 (CAS RN 6417-83-0) and preparations based thereon with a colourant C.I. Pigment Red 63:1 content of 70 % or more by weight
|
0 %
|
-
|
31.12.2023
|
ex 3205 00 00
|
20
|
Colourant C.I. Solvent Red 48 (CAS RN 13473-26-2) preparation, in a form of dry powder, containing by weight:
—
|
16 % or more but not more than 25 % of Colourant C.I. Solvent Red 48 (CAS RN 13473-26-2)
|
—
|
65 % or more but no more than 75 % of aluminium hydroxide (CAS RN 21645-51-2)
|
|
0 %
|
-
|
31.12.2023
|
ex 3205 00 00
|
30
|
Colourant C.I. Pigment Red 174 (CAS RN 15876-58-1) preparation, in a form of dry powder, containing by weight:
—
|
16 % or more but not more than 21 % of Colourant C.I. Pigment Red 174 (CAS RN 15876-58-1)
|
—
|
65 % or more but no more than 69 % of aluminium hydroxide (CAS RN 21645-51-2)
|
|
0 %
|
-
|
31.12.2023
|
ex 3208 90 19
|
55
|
Preparation of 5 % or more but not more than 20 % by weight of a copolymer of propylene and maleic anhydride, or a blend of polypropylene and a copolymer of propylene and maleic anhydride, or a blend of polypropylene and a copolymer of propylene, isobutene and maleic anhydride in an organic solvent
|
0 %
|
-
|
31.12.2020
|
ex 3506 91 90
|
10
|
Adhesive based on an aqueous dispersion of a mixture of dimerised rosin and a copolymer of ethylene and vinyl acetate (EVA)
|
0 %
|
-
|
31.12.2023
|
ex 3506 91 90
|
40
|
Acrylic pressure sensitive adhesive with a thickness of 0,076 mm or more but not more than 0,127 mm, put up in rolls of a width of 45,7 cm or more but not more than 132 cm supplied on a release liner with an initial peel adhesion release value of not less than 15 N/25 mm (measured according to ASTM D3330)
|
0 %
|
-
|
31.12.2019
|
ex 3506 91 90
|
50
|
Preparation containing by weight:
—
|
15 % or more but not more than 60 % of styrene butadiene copolymers or styrene isoprene copolymers and
|
—
|
10 % or more but not more than 30 % of pinene polymers or pentadiene copolymers
|
dissolved in :
—
|
Methyl ethyl ketone (CAS RN 78-93-3)
|
—
|
Heptane (CAS RN 142-82-5), and
|
—
|
Toluene (CAS RN 108-88-3) or light aliphatic solvent naphtha (CAS RN 64742-89-8)
|
|
0 %
|
-
|
31.12.2020
|
ex 3506 91 90
|
60
|
Temporary wafer-bonding adhesive material in the form of a suspension of a solid polymer in D-limonene (CAS RN 5989-27-5) with a polymeric content by weight of 25 % or more but not more than 35 %
|
0 %
|
l
|
31.12.2022
|
ex 3812 39 90
|
35
|
Mixture containing by weight:
—
|
25 % or more but not more than 55 % of a mixture of C15-18 tetramethylpiperidinyl esters (CAS RN 86403-32-9)
|
—
|
not more than 20 % of other organic compounds
|
—
|
on a carrier of polypropylene (CAS RN 9003-07-0) or amorphous silica (CAS RN 7631-86-9 or 112926-00-8)
|
|
0 %
|
-
|
31.12.2023
|
ex 3815 12 00
|
20
|
Spherical catalyst consisting of a support of aluminium oxide coated with platinum, with
—
|
a diameter of 1,4 mm or more but not more than 2,0 mm, and
|
—
|
a platinum content by weight of 0,2 % or more but not more than 0,5 %
|
|
0 %
|
-
|
31.12.2023
|
ex 3815 12 00
|
30
|
Catalyst
—
|
containing 0,3 gram per litre or more, but not more than 7 gram per litre of precious metals,
|
—
|
deposited on a ceramic honeycomb structure coated with aluminium oxide or cerium/zirconium oxide, the honeycomb structure having
|
—
|
a nickel content of 1,26 % by weight or more, but not more than 1,29 % by weight,
|
—
|
62 cells per cm² or more, but not more than 140 cells per cm² ,
|
—
|
a diameter of 100 mm or more, but not more than 120 mm and
|
—
|
a length of 60 mm or more, but not more than 150 mm,
|
for use in the production of motor vehicles (2)
|
0 %
|
-
|
31.12.2023
|
ex 3815 90 90
|
43
|
Catalyst in powder form consisting by weight of
—
|
92,50 % (± 2) % titanium dioxide (CAS RN 13463-67-7)
|
—
|
5 % (± 1) % silicon dioxide (CAS RN 112926-00-8) and
|
—
|
2,5 % (± 1,5) % sulphur trioxide (CAS RN 7446-11-9)
|
|
0 %
|
-
|
31.12.2022
|
ex 3824 99 92
|
31
|
Liquid crystal mixtures for use in the manufacture of LCD (liquid crystal display) modules (2)
|
0 %
|
-
|
31.12.2023
|
ex 3824 99 92
|
37
|
Mixture of acetates of 3-butene-1,2-diol with a content by weight of 65 % or more of 3-butene-1,2-diol diacetate (CAS RN 18085-02-4)
|
0 %
|
-
|
31.12.2023
|
ex 3824 99 96
|
33
|
Buffer cartridge not exceeding 8000 ml containing:
—
|
0.05 % or more but not more than 0.1 % by weight of 5-Chloro-2-methyl-2,3-dihydroisothiazol-3-one (CAS RN 55965-84-9) and
|
—
|
0.05 % or more but not more that 0.1 % by weight of 2-Methyl-2,3-dihydroisothiazol-3-one (CAS RN 2682-20-4) as a biostatic
|
|
0 %
|
-
|
31.12.2023
|
ex 3904 69 80
|
20
|
Copolymer of tetrafluoroethylene, heptafluoro-1-pentene and ethene (CAS RN 94228-79-2)
|
0 %
|
-
|
31.12.2023
|
ex 3904 69 80
|
30
|
Copolymer of tetrafluoroethylene, hexafluoropropene and ethene
|
0 %
|
-
|
31.12.2023
|
ex 3907 20 20
|
40
|
Copolymer of tetrahydrofuran and tetrahydro-3-methylfuran with a number average molecular weight (Mn) of 900 or more but not more than 3 600
|
0 %
|
-
|
31.12.2023
|
ex 3920 99 59
|
30
|
Poly(tetrafluoroethylene) film containing by weight 10 % or more of graphite
|
0 %
|
-
|
31.12.2023
|
ex 3921 19 00
|
40
|
Transparent, microporous, acrylic acid grafted polyethylene film, in the form of rolls, with:
—
|
a width of 98 mm or more but not more than170 mm,
|
—
|
a thickness of 15 µm or more but not more than 36 µm,
|
of a kind used for the manufacture of alkaline battery separators
|
0 %
|
-
|
31.12.2019
|
ex 3926 30 00
|
40
|
Plastic internal door handle used in the manufacture of motor vehicles (2)
|
0 %
|
-
|
31.12.2023
|
ex 5402 44 00
|
10
|
Synthetic elastomeric filament yarn:
—
|
untwisted or with a twist not exceeding 50 turns per metre, measuring 300 dtex or more but not more than 1000 dtex
|
—
|
composed of polyurethane ureas based on a copolyether glycol of tetrahydrofuran and 3-methyltetrahydrofuran
|
for use in the manufacture of disposable hygiene products of heading 9619 (2)
|
0 %
|
-
|
31.12.2023
|
ex 7006 00 90
|
40
|
Plates of sodalime glass of STN (Super Twisted Nematic) quality having:
—
|
a length of 300 mm or more but not more than 600 mm,
|
—
|
a width of 300 mm or more but not more than 600 mm,
|
—
|
a thickness of 0,5 mm or more but not more than 1,1 mm,
|
—
|
an indium-tin-oxide coating with a resistance of 80 Ohms or more, but not more than 160 Ohms on one side,
|
—
|
a multi layer anti-reflection-coating on the other side and
|
—
|
machined (chamfered) edges
|
of a kind used in the manufacture of LCD (liquid crystal display) modules
|
0 %
|
-
|
31.12.2023
|
ex 7019 40 00
ex 7019 52 00
|
70
30
|
E-fibre glass fabrics:
—
|
having a weight of 20 g/m² or more, but not more than 214 g/m²,
|
—
|
impregnated with silane,
|
—
|
in rolls,
|
—
|
having a humidity content by weight of 0,13 % or less, and
|
—
|
having not more than 3 hollow fibres out of 100 000 fibres,
|
for the exclusive use in the manufacture of prepregs and copper clad laminates (2)
|
0 %
|
-
|
31.12.2021
|
ex 7019 52 00
|
40
|
Epoxy resin coated glass woven fabric containing by weight:
—
|
91 % or more but not more than 93 % of glass fibres,
|
—
|
7 % or more but not more than 9 % of epoxy resin
|
|
0 %
|
-
|
31.12.2023
|
ex 7410 11 00
ex 8507 90 80
ex 8545 90 90
|
10
60
30
|
Roll of laminate foil of graphite and copper, with:
—
|
a width of 610 mm or more but not more than 620 mm, and
|
—
|
a diameter of 690 mm or more but not more than 710 mm,
|
for use in the manufacture of lithium-ion electric rechargeable batteries (2)
|
0 %
|
-
|
31.12.2019
|
ex 7607 20 90
|
10
|
Aluminium foil, in rolls:
—
|
coated with polypropylene on one side and with polyamide on the other side with adhesive layers between
|
—
|
with a width of 200 mm or more, but not more than 400 mm,
|
—
|
with a thickness of 0,138 mm or more, but not more than 0,168 mm
|
for use in the manufacture of lithium-ion battery cell pouches (2)
|
0 %
|
-
|
31.12.2019
|
8104 11 00
|
|
Unwrought magnesium, containing at least 99,8 % by weight of magnesium
|
0 %
|
-
|
31.12.2023
|
ex 8108 20 00
|
40
|
Titanium alloy ingot,
—
|
with a height of 17,8 cm or more, a length of 180 cm or more and a width of 48,3cm or more,
|
—
|
a weight of 680 kg or more,
|
containing alloy elements by weight of::
—
|
3 % or more but not more than 6 % of aluminium,
|
—
|
2,5 % or more but not more than 5 % of tin,
|
—
|
2,5 % or more but not more than 4,5 % of zirconium,
|
—
|
0,2 % or more but not more than 1 % of niobium,
|
—
|
0,1 % or more but not more than 1 % of molybdenum,
|
—
|
0,1 % or more but not more than 0,5 % of silicon
|
|
0 %
|
p/st
|
31.12.2020
|
ex 8108 20 00
|
60
|
Titanium alloy ingot,
—
|
with a diameter of 63,5 cm or more and a length of 450 cm or more,
|
—
|
a weight of 6 350 kg or more,
|
containing alloy elements by weight of:
—
|
5,5 % or more but not more than 6,7 % of aluminium,
|
—
|
3,7 % of more but not more than 4,9 % of vanadium
|
|
0 %
|
p/st
|
31.12.2020
|
ex 8301 20 00
|
10
|
Mechanical or electromechanical steering column lock:
—
|
with a height of 10,5 cm (± 3 cm),
|
—
|
with a width of 6,5 cm (± 3 cm),
|
—
|
in a metal housing,
|
—
|
whether or not with a holder
|
for use in the manufacture of goods of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8302 30 00
|
10
|
Support bracket for an exhaust system:
—
|
with a thickness of 0,7 mm or more but not more than 1,3 mm,
|
—
|
of stainless steel class 1.4310 and 1.4301 according to norm EN 10088,
|
—
|
whether or not with mounting holes
|
for use in the manufacture of exhaust systems for automobiles (2)
|
0 %
|
-
|
31.12.2023
|
ex 8409 91 00
|
60
|
The air intake module for engine cylinders consisting of:
—
|
a suction pipe,
|
—
|
a pressure sensor,
|
—
|
an electric throttle,
|
—
|
hoses,
|
—
|
brackets
|
for use in the manufacture of goods of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8409 91 00
|
70
|
Inlet manifold, exclusively for use in the manufacture of the motor vehicles with:
—
|
a width of 40 mm or more but not more than 70 mm,
|
—
|
valves length of 250 mm or more but not more than 350 mm,
|
—
|
air volume of 5,2 litres, and
|
—
|
an electrical flow control system that provides maximum performance at more than 3200 rpm
|
(2)
|
0 %
|
-
|
31.12.2023
|
ex 8409 99 00
|
65
|
The exhaust gas recirculation assembly consisting of:
—
|
a control unit,
|
—
|
an air throttle,
|
—
|
an intake pipe,
|
—
|
an outlet hose
|
for use in the manufacture of diesel engines of motor vehicles (2)
|
0 %
|
-
|
31.12.2023
|
ex 8414 10 25
|
30
|
Tandem pump consisting of:
—
|
an oil pump with displacement of 21,6 cc/rev (± 2 cc/rev) and working pressure 1,5 bar at 1 000 revolutions per minute,
|
—
|
vacuum pump with displacement of 120 cc/rev (± 12 cc/rev) and performance of -666 mbar in 6 seconds at 750 revolutions per minute,
|
for use in the manufacture of engines of motor vehicles (2)
|
0 %
|
-
|
31.12.2023
|
ex 8414 10 89
|
30
|
Electric vacuum pump with:
—
|
Controller Area Network (CAN bus),
|
—
|
whether or not with a rubber hose,
|
—
|
a connecting cable with connector,
|
—
|
a mounting bracket
|
for use in the manufacture of goods of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8414 30 89
|
30
|
Open shaft, scroll type compressor with clutch assembly, of a power of more than 0,4 kW, for air conditioning in vehicles, for use in the manufacture of motor vehicles of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8414 59 35
|
20
|
Radial fan, with:
—
|
a dimension of 25mm (height) x 85mm (width) x 85mm (depth),
|
—
|
a weight of 120 g,
|
—
|
a rated voltage of 13,6 VDC (direct current voltage),
|
—
|
an operating voltage of 9 VDC or more but not more than 16 VDC (direct current voltage),
|
—
|
a rated current of 1,1 A (TYP),
|
—
|
a rated power of 15 W,
|
—
|
a rotation speed of 500 RPM (revolutions per minute) or more but not more than 4800 RPM (revolutions per minute) (free flow),
|
—
|
an air flow of not more than 17,5 litre/s,
|
—
|
an air pressure of not more than16 mm H2O ≈ 157 Pa,
|
—
|
an overall sound pressure of not more than 58 dB(A) at 4800 RPM (revolutions per minute), and
|
with a FIN (Fan Interconnect Network) interface for communication with the heating and air-conditioning control unit used in car seat ventilation systems
|
0 %
|
-
|
31.12.2023
|
ex 8467 99 00
|
10
|
Mechanical switches for connecting electrical circuits, with:
—
|
a voltage of 14,4 V or more but not more than 42 V,
|
—
|
an amperage of 10 A or more but not more than 42 A,
|
for use in the manufacture of machines falling within heading 8467 (2)
|
0 %
|
p/st
|
31.12.2019
|
ex 8481 80 59
|
30
|
Two-way flow control valve with housing, with:
—
|
at least 5, but not more than 10 outlet holes with at least 0,09 mm, but not more than 0,2 mm diameter,
|
—
|
at least 550 cm3/minute, but not more than 2000 cm3/minute flow rate,
|
—
|
at least 19, but not more than 300 MPa operating pressure
|
|
0 %
|
-
|
31.12.2022
|
ex 8481 80 59
|
40
|
Flow-control valve
—
|
made of steel,
|
—
|
with an outlet hole with a diameter of at least 0,1 mm, but not more than 0,3 mm,
|
—
|
with an inlet hole with a diameter of at least 0,4 mm, but not more than 1,3 mm,
|
—
|
with chromium nitride coating,
|
—
|
with a surface roughness of Rp 0,4
|
|
0 %
|
-
|
31.12.2022
|
ex 8481 80 59
|
50
|
Electromagnetic valve for quantity control with
—
|
a plunger,
|
—
|
a solenoid with a of coil resistance of at least 2,6 Ohm, but not more than 3 Ohm
|
|
0 %
|
-
|
31.12.2022
|
ex 8481 80 59
|
60
|
Electromagnetic valve for quantity control
—
|
with a solenoid with a coil resistance of at least 0,19 Ohm, but not more than 0,66 Ohm, and with an inductance of not more than 1 mH
|
|
0 %
|
-
|
31.12.2022
|
ex 8481 80 79
ex 8481 80 99
|
30
30
|
Service Valve which suits for R410A or R32 gas while connecting indoor and outdoor units with:
—
|
a withstanding pressure of the valve body of 6,3 MPa,
|
—
|
a leakage ratio of less than 1,6 g/a,
|
—
|
an impurity ratio of less than 1,2 mg/PCS,
|
—
|
an airtight pressure of the valve body of 4,2 MPa,
|
for use in the manufacture of air conditioners (2)
|
0 %
|
-
|
31.12.2023
|
ex 8484 20 00
|
20
|
Mechanical face sealing device made of two movable rings (one ceramic mating, having a thermal conductivity lower than 80W/Mk and the other carbon sliding), one spring and a nitrile sealant on the external side, of a kind used in manufacturing circulation pumps of cooling systems in motor vehicles
|
0 %
|
-
|
31.12.2023
|
ex 8501 10 10
|
30
|
Motors for air pumps, with:
—
|
operating voltage of 9 VDC or more but not more than 24 VDC,
|
—
|
operating temperature range of -40°C or more but not more than 80°C,
|
—
|
an output not exceeding 18 W
|
for use in the manufacture of pneumatic support and ventilation systems for car seats (2)
|
0 %
|
-
|
31.12.2023
|
ex 8501 31 00
ex 8501 32 00
|
55
40
|
DC motor with or without commutator, with
—
|
an external diameter of 24,2 mm or more, but not more than 140 mm,
|
—
|
a rated speed of 3300 rpm or more, but not more than 26200 rpm,
|
—
|
a rated supply voltage of 3,6 V or more, but not more than 230 V,
|
—
|
an output power of more than 37,5 W , but not more than 2400 W,
|
—
|
a free load current of not more than 20,1 A,
|
—
|
a maximum efficiency of 50 % or more,
|
for driving hand-held power tools or lawn mowers
|
0 %
|
-
|
31.12.2023
|
ex 8501 33 00
|
25
|
AC traction motor of an output of 75 kW or more but not more than 375 kW, with:
—
|
a torque output of 200 Nm or more but not more than 300 Nm,
|
—
|
a power output of 50 kW or more but not more than 100 kW, and
|
—
|
a speed of not more than 15 000 rpm
|
for use in the manufacture of electric vehicles (2)
|
0 %
|
-
|
31.12.2019
|
ex 8503 00 99
|
55
|
Stator for brushless motor, with:
—
|
an internal diameter of 206,6 mm (± 0,5)
|
—
|
an external diameter of 265,0 mm (± 0,2) and
|
—
|
a width of 37,2 mm or more but not more than 47,8 mm
|
of a kind used in the manufacture of washing machine, washer-dryer or dryer equipped with direct drive drums
|
0 %
|
p/st
|
31.12.2020
|
ex 8506 90 00
|
10
|
Cathode, in rolls, for air zinc button cell batteries (hearing aid batteries) (2)
|
0 %
|
-
|
31.12.2023
|
ex 8507 60 00
|
13
|
Prismatic lithium-ion electric accumulators with:
—
|
a width of 173,0 mm (± 0,4 mm),
|
—
|
a thickness of 45,0 mm (± 0,4 mm),
|
—
|
a height 125,0 mm (± 0,3 mm),
|
—
|
a nominal voltage of 3,67 V (± 0,01 V), and
|
—
|
a nominal capacity of 94 Ah and/or 120 Ah
|
for use in the manufacture of rechargeable electric vehicle batteries (2)
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
15
|
Cylindrical lithium-ion-accumulators or modules with:
—
|
a nominal capacity of 8,8 Ah or more, but not more than 18 Ah,
|
—
|
a nominal voltage of 36 V or more, but not more than 48 V,
|
—
|
a power of 300 Wh or more, but not more than 648 Wh,
|
for use in the manufacture of electric bicycles (2)
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
18
|
Rectangular lithium-ion polymer accumulator equipped with a battery management system and can-bus interface with:
—
|
a length of not more than 1600 mm,
|
—
|
a width of not more than 448 mm,
|
—
|
a height of not more than 395 mm,
|
—
|
a weight of 125 kg or more but not more than 135 kg,
|
—
|
a nominal voltage of 280 V or more but not more than 400 V,
|
—
|
a nominal capacity of 9,7 Ah or more but not more than 10,35 Ah,
|
—
|
a charging voltage of 110 V or more but not more than 230 V, and
|
—
|
containing 6 modules with 90 cells or more but not more than 96 cells enclosed in a steel casing
|
for use in the manufacture of vehicle capable of being charged by plugging to external source of electric power of heading 8703 (2)
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
30
|
Cylindrical lithium-ion accumulator or module, with a length of 63 mm or more and a diameter of 17,2 mm or more, having a nominal capacity of 1 200 mAh or more, for use in the manufacture of rechargeable batteries (2)
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
33
|
Lithium-ion accumulator, with:
—
|
a length of 150 mm or more, but not more than 1 000 mm,
|
—
|
a width of 100 mm or more, but not more than 1 000 mm,
|
—
|
a height of 200 mm or more, but not more than 1 500 mm,
|
—
|
a weight of 75 kg or more, but not more than 200 kg,
|
—
|
a nominal capacity not less than 150 Ah and not more than 500 Ah
|
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
50
|
Modules for the assembly of batteries of ion lithium electric accumulators with:
—
|
a length of 298 mm or more, but not more than 408 mm,
|
—
|
a width of 33,5 mm or more, but not more than 209 mm,
|
—
|
a height of 138 mm or more, but not more than 228 mm,
|
—
|
a weight of 3,6 kg or more, but not more than 17 kg, and
|
—
|
a power of 458 Wh or more, but not more than 2 158 Wh
|
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
71
|
Lithium-ion rechargeable batteries, with:
—
|
a length of 700 mm or more, but not more than 2 820 mm
|
—
|
a width of 935 mm or more, but not more than 1 660 mm
|
—
|
a height of 85 mm or more, but not more than 700 mm
|
—
|
a weight of 250 kgor more, but not more than 700 kg
|
—
|
a power of not more than 175 kWh
|
|
0 %
|
-
|
31.12.2019
|
ex 8507 60 00
|
85
|
Lithium-ion Rectangular modules for incorporation in lithium-ion rechargeable batteries:
—
|
of a length of 300 mm or more, but not more than 350 mm,
|
—
|
of a width of 79,8 mm or more, but not more than 225 mm,
|
—
|
of a height of 35 mm or more, but not more than 168 mm,
|
—
|
of a weight of 3,95 kg or more, but not more than 8,85 kg,
|
—
|
with a rating of 66,6 Ah or more, but not more than 129 Ah
|
|
0 %
|
-
|
31.12.2019
|
ex 8507 90 30
|
20
|
Safety Reinforced Separator designed to separate cathode and anode in lithium-ion electric accumulators for motor vehicle batteries for use in the manufacture of lithium-ion electric accumulators for motor vehicle batteries
|
0 %
|
-
|
31.12.2019
|
ex 8529 90 65
|
25
|
Printed circuit board assembly comprising:
—
|
a radio tuner (capable of receiving and decoding radio signals and transmitting those signals within the assembly) without signal processing capabilities,
|
—
|
a microprocessor capable of receiving remote control messages and controlling the tuner chipset,
|
for use in the manufacture of home entertainment systems (2)
|
0 %
|
p/st
|
31.12.2019
|
ex 8529 90 65
|
28
|
Electronic assembly comprising at least
—
|
a printed circuit board with,
|
—
|
processors for multi-media applications and video signal processing,
|
—
|
FPGA (Field Programmable Gate Array),
|
—
|
Flash memory,
|
—
|
operating memory,
|
—
|
USB-interface,
|
—
|
with or without HDMI, VGA- and RJ-45 interfaces,
|
—
|
sockets and plugs for connecting a LCD-display, a LED lighting and a control panel
|
|
0 %
|
p/st
|
31.12.2020
|
ex 8529 90 65
|
40
|
Printed circuit board subassembly, comprising:
—
|
a radio tuner, capable of receiving and decoding radio signals and transmitting those signals within the assembly, with a signal decoder,
|
—
|
a radio frequency (RF) remote control receiver,
|
—
|
an infrared remote control signal transmitter,
|
—
|
a SCART signal generator
|
—
|
a TV state sensor
|
for use in the manufacture of home entertainment systems (2)
|
0 %
|
p/st
|
31.12.2019
|
ex 8529 90 92
|
52
|
LCD module, glass or plastic covered and optically bonded, with
—
|
a diagonal measurement of the screen of 12 cm or more but not more than 31 cm,
|
—
|
LED backlighting,
|
—
|
a printed circuit board with EEPROM (Electrically Erasable Programmable Read-Only Memory), microcontroller, timing controller and other active and passive components,
|
—
|
a plug for power supply and CAN (Controller Area Network) and LVDS (Low Voltage Differential Signalling) interfaces,
|
—
|
whether or not with electronic components to generate additional control indicators for vehicle information on the display,
|
—
|
with or without a touch screen,
|
—
|
without a signal processing module,
|
—
|
in a housing with additional LED indicators for warning lights,
|
—
|
with or without a gear shift indicator and a photo sensor,
|
of a kind used as a driver information display in motor vehicles of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8529 90 92
|
54
|
LCD display with:
—
|
a touch panel,
|
—
|
at least one printed circuit board for simple slave device pixel addressing (Timing Controller function) and touch control, with EEPROM (Electrically Erasable Programmable Read-Only Memory) for display settings,
|
—
|
a diagonal screen measurement of 15 cm or more but not more than 21 cm,
|
—
|
a backlight,
|
—
|
a LVDS (Low Voltage Differential Signalling) and a power supply connector,
|
for use in the manufacture of motor vehicles of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8529 90 92
|
57
|
Metal holder, metal fixing item or internal stiffener of metal, for use in the manufacture of televisions, monitors and video players
(2)
|
0 %
|
p/st
|
31.12.2021
|
ex 8535 90 00
|
30
|
Semiconductor module switch in a casing:
—
|
consisting of an IGBT transistor chip and a diode chip on one or more lead frames,
|
—
|
for a voltage of 600 V or 1 200 V
|
|
0 %
|
p/st
|
31.12.2020
|
ex 8537 10 91
|
57
|
Programmable memory control board with:
—
|
4 or more stepper motor drivers,
|
—
|
4 or more outputs with MOSFET transistors,
|
—
|
a main processor,
|
—
|
3 or more inputs for temperature sensors,
|
—
|
for a voltage of 10 V or more but not more than 30 V
|
for use in the manufacture of 3D printers (2)
|
0 %
|
-
|
31.12.2023
|
ex 8537 10 91
|
59
|
Electronic control units for controlling inter axle torque transferring in all-wheel drive vehicles including:
—
|
a printed circuit board with programmable memory controller,
|
—
|
one single connector, and
|
—
|
working at 12 V
|
|
0 %
|
-
|
31.12.2023
|
ex 8537 10 91
|
63
|
Electronic control units able to control automatic continuous variable transmission for passenger vehicles including:
—
|
a printed circuit board with programmable memory controller,
|
—
|
a metallic housing,
|
—
|
one single connector,
|
—
|
working at 12V
|
|
0 %
|
-
|
31.12.2023
|
ex 8537 10 91
|
67
|
Electronic Engine Control Unit (ECU) with:
—
|
a printed circuit board (PCB),
|
—
|
12 Volts voltage,
|
—
|
reprogrammable,
|
—
|
a micro-processor that can control, evaluate and manage support service functions in cars (injection and ignition advance values of fuel, fuel and air flow rate)
|
for use in the manufacture of goods of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8708 40 20
ex 8708 40 50
|
60
50
|
Automatic transmission assembly with rotary gear shifter with:
—
|
aluminium casting housing,
|
—
|
differential gear,
|
—
|
9 Speed automatic,
|
—
|
electronic range select gear selection system,
|
with dimensions of:
—
|
a width of 330 mm or more but not more than 420 mm,
|
—
|
a height of 380 mm or more but not more than 450 mm,
|
—
|
a length of 580 mm or more but not more than 690 mm,
|
for use in the manufacture of the vehicles in heading 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8708 50 20
ex 8708 50 99
ex 8708 99 10
ex 8708 99 97
|
60
15
45
65
|
Car transfer case with single input, dual output, to distribute torque between front and rear axles in an aluminium housing, with dimension of not more than 565 x 570 x 510 mm, comprising at least:
—
|
an actuator, and
|
—
|
a interior distribution by chain
|
|
0 %
|
-
|
31.12.2019
|
ex 8708 50 20
ex 8708 50 99
|
65
20
|
Intermediate steel shaft connecting the gearbox with semi-axle with:
—
|
a length of 300 mm or more but not more than 650 mm,
|
—
|
a spline end on both sides,
|
—
|
whether or not with a pressed bearing in the case,
|
—
|
whether or not with a holder
|
for use in the manufacture of goods of Chapter 87 (2)
|
0 %
|
-
|
31.12.2023
|
ex 8708 50 20
ex 8708 50 99
|
70
25
|
Housing of tripod type half shaft inboard joint for transmitting a torque from engine and transmission to wheels of motor vehicles with:
—
|
an outer diameter of 67,0 mm or more but not more than 84,5 mm,
|
—
|
3 cold calibrated roller tracks with a diameter of 29,90 mm or more but not more than 36,60 mm,
|
—
|
sealing diameter 34,0 mm or more but not more than 41,0 mm, without lead angle,
|
—
|
spline with 21 teeth or more but not more than 35,
|
—
|
bearing seat diameter of 25,0 mm or more but not more than 30,0 mm, with or without oil grooves
|
|
0 %
|
-
|
31.12.2023
|
ex 8708 50 20
ex 8708 50 99
|
75
35
|
Outboard joint assembly for transmitting a torque from engine and transmission to wheels of motor vehicles, consisting of:
—
|
an inner race with 6 ball tracks for running with the bearing balls with a diameter 15,0 mm or more but not more than 20,0 mm,
|
—
|
an outer race with 6 ball tracks for running with 6 bearing balls, made of steel with carbon content of 0,45 % or more but not more than 0,58 %, with thread and with a spline with 26 teeth or more but not more than 38,
|
—
|
a spherical cage keeping bearing balls in the ball tracks of outer race and inner race in proper angular position, made of material suitable for carburizing with carbon content of 0,14 % or more but not more than 0,25 %, and
|
—
|
with a grease compartment,
|
capable of working at constant speed at variable articulation angle not higher than 50 degrees
|
0 %
|
-
|
31.12.2023
|
ex 8708 80 99
|
20
|
Aluminium suspension link arm, with dimensions of:
—
|
a height of 50 mm or more but not more than 150 mm,
|
—
|
a width of 10 mm or more but not more than 100 mm,
|
—
|
a length of 100 mm or more but not more than 600 mm,
|
—
|
a mass of 1000 g or more but not more than 3000 g,
|
Equipped with at least two bushed holes made of aluminium alloy with the following characteristics:
—
|
a tensile strength of 2000 mPa or more ,
|
—
|
a strength of 19 kN or more,
|
—
|
a stiffness of 5 kN/mm or more but not more than 9 kN/mm,
|
—
|
a frequency of 400 Hz or more but not more than 600 Hz
|
|
0 %
|
-
|
31.12.2023
|
ex 8708 92 99
|
10
|
Exhaust system inner liner:
—
|
with a wall thickness of 0,7 mm or more but not more than 1,3 mm,
|
—
|
made of stainless steel sheets or coil class 1.4310 and 1.4301 according to norm EN 10088,
|
—
|
whether or not with mounting holes
|
for use in the manufacture of exhaust systems for automobiles (2)
|
0 %
|
-
|
31.12.2023
|
ex 8708 92 99
|
20
|
Pipe for guiding exhaust gases from the combustion engine:
—
|
with a diameter of 40 mm or more but not more than 100 mm,
|
—
|
with a length of 90 mm or more but not more than 410 mm,
|
—
|
with a wall thickness of 0,7 mm or more but not more than 1,3 mm,
|
—
|
of stainless steel
|
for use in the manufacture of exhaust systems for automobiles (2)
|
0 %
|
-
|
31.12.2023
|
ex 8708 92 99
|
30
|
Exhaust system end cover:
—
|
with a wall thickness of 0,7 mm or more but not more than 1,3 mm,
|
—
|
made of stainless steel class 1.4310 and 1.4301 according to norm EN 10088,
|
—
|
whether or not with inner liner,
|
—
|
whether or not with surface treatment
|
for use in the manufacture of exhaust systems for automobiles (2)
|
0 %
|
-
|
31.12.2023
|
ex 9001 90 00
|
55
|
Optical, diffuser, reflector or prism sheets, unprinted diffuser plates, whether or not possessing polarising properties, specifically cut
|
0 %
|
-
|
31.12.2023
|
ex 9002 11 00
|
15
|
Infrared lens with motorised focus adjustment,
—
|
using wavelengths of 3 μm or more but not more than 5 μm,
|
—
|
providing a clear picture from 50 m to infinity,
|
—
|
with fields of vision sizes of 3° x 2,25° and 9° x 6,75 °,
|
—
|
with a weight of not more than 230 g,
|
—
|
with a length of not more than 88 mm,
|
—
|
with a diameter of not more than 46 mm,
|
—
|
athermalized,
|
for use in the manufacture of thermal imaging cameras, infrared binoculars, weapons scopes (2)
|
0 %
|
-
|
31.12.2020
|
ex 9002 11 00
|
18
|
Lens assembly consisting of a cylinder-shaped cover made of metal or plastic and optical elements with:
—
|
a horizontal field of view range to a maximum of 120 deg,
|
—
|
a diagonal field of view range to a maximum of 92 deg,
|
—
|
a focal length to a maximum of 7,50 mm,
|
—
|
a relative aperture of a maximum of F/2,90,
|
—
|
a maximum diameter of 22 mm
|
of a kind used for the production of CMOS (Complementary metal–oxide-semiconductor) automotive cameras
|
0 %
|
-
|
31.12.2023
|
ex 9002 11 00
|
25
|
Infrared optical unit composed of
—
|
a monocrystalline silicon lens with a diameter of 84 mm (± 0,1 mm) and
|
—
|
a monocrystalline germanium lens with a diameter of 62 mm (± 0,05 mm)
|
assembled on a machined aluminium alloy support, of a kind used for thermal imaging cameras
|
0 %
|
-
|
31.12.2021
|
ex 9002 11 00
|
35
|
Infrared optical unit composed of
—
|
a silicon lens with a diameter of 29 mm (± 0,05 mm) and
|
—
|
a monocrystalline calcium fluoride lens with a diameter of 26 mm (± 0,05 mm),
|
assembled on a machined aluminium alloy support, of kind a used for thermal imaging cameras
|
0 %
|
-
|
31.12.2021
|
ex 9002 11 00
|
45
|
Infrared optical unit
—
|
with a silicon lens of a diameter of 62 mm (± 0,05 mm),
|
—
|
mounted on a machined aluminium alloy support
|
of a kind used for thermal cameras
|
0 %
|
-
|
31.12.2021
|
ex 9002 11 00
|
55
|
Infrared optical unit composed of
—
|
a germanium lens with a diameter of 11 mm (± 0,05 mm),
|
—
|
a monocrystalline calcium fluoride lens with a diameter of 14 mm (± 0,05 mm), and
|
—
|
a silicon lens with a diameter of 17 mm (± 0,05 mm),
|
assembled on a machined aluminium alloy support, of a kind used for thermal imaging cameras
|
0 %
|
-
|
31.12.2021
|
ex 9002 11 00
|
65
|
Infrared optical unit
—
|
with a silicon lens with a diameter of 26 mm (± 0,1 mm),
|
—
|
mounted on a machined aluminum alloy support,
|
of a kind used for thermal imaging cameras
|
0 %
|
-
|
31.12.2021
|
ex 9002 11 00
|
75
|
Infrared optical unit composed of
—
|
a germanium lens with a diameter of 19 mm (± 0,05 mm),
|
—
|
a monocrystalline calcium fluoride lens with a diameter of 18 mm (± 0,05 mm),
|
—
|
a germanium lens with a diameter of 20,6 mm (± 0,05 mm),
|
assembled on a machined aluminium alloy support, of a kind used for thermal imaging cameras
|
0 %
|
-
|
31.12.2021
|
ex 9029 20 31
ex 9029 90 00
|
20
30
|
Clustered instrument panel with the microprocessor control board, with or without stepping motors, and LED indicators showing at least:
—
|
speed,
|
—
|
engine revolutions,
|
—
|
engine temperature,
|
—
|
the fuel level
|
communicating via CAN-BUS and/or K-LINE protocols, of a kind used in the manufacture of goods of Chapter 87
|
0 %
|
p/st
|
31.12.2019
|