EUR-Lex Access to European Union law
This document is an excerpt from the EUR-Lex website
Document 02018R0858-20221206
Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (Text with EEA relevance)Text with EEA relevance
Consolidated text: Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (Text with EEA relevance)Text with EEA relevance
Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (Text with EEA relevance)Text with EEA relevance
02018R0858 — EN — 06.12.2022 — 003.002
This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document
|
REGULATION (EU) 2018/858 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (OJ L 151 14.6.2018, p. 1) |
Amended by:
|
|
|
Official Journal |
||
|
No |
page |
date |
||
|
REGULATION (EU) 2019/2144 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 November 2019 |
L 325 |
1 |
16.12.2019 |
|
|
COMMISSION DELEGATED REGULATION (EU) 2021/1445 of 23 June 2021 |
L 313 |
4 |
6.9.2021 |
|
|
COMMISSION DELEGATED REGULATION (EU) 2022/2236 of 20 June 2022 |
L 296 |
1 |
16.11.2022 |
|
Corrected by:
REGULATION (EU) 2018/858 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL
of 30 May 2018
on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC
(Text with EEA relevance)
CHAPTER I
SUBJECT MATTER, SCOPE AND DEFINITIONS
Article 1
Subject matter
This Regulation also lays down provisions for the placing on the market and the entry into service of parts and equipment that may pose a serious risk to the correct functioning of the essential systems of the vehicles referred to in Article 2(1).
Article 2
Scope
This Regulation does not apply to the following vehicles:
agricultural or forestry vehicles, as defined in Regulation (EU) No 167/2013 of the European Parliament and of the Council ( 1 );
two- or three-wheel vehicles and quadricycles, as defined in Regulation (EU) No 168/2013 of the European Parliament and of the Council ( 2 );
track-laying vehicles;
vehicles designed and constructed or adapted for use by the armed services only.
For the following vehicles, the manufacturer may apply for type-approval or individual vehicle approval under this Regulation, provided that those vehicles fulfil the requirements of this Regulation:
vehicles designed and constructed for use principally on construction sites or in quarries, port or airport facilities;
vehicles designed and constructed or adapted for use by civil protection, fire services and forces responsible for maintaining public order;
any self-propelled vehicle designed and constructed specifically to perform work and that, because of its construction characteristics, is not suitable for carrying passengers or for transporting goods, and that is not machinery mounted on a motor vehicle chassis.
Such approvals shall be without prejudice to the application of Directive 2006/42/EC of the European Parliament and of the Council ( 3 ).
For the following vehicles, the manufacturer may apply for individual vehicle approval under this Regulation:
vehicles intended exclusively for racing on roads;
prototypes of vehicles used on the road under the responsibility of a manufacturer to perform a specific test programme provided they have been specifically designed and constructed for that purpose.
Article 3
Definitions
For the purposes of this Regulation and the regulatory acts listed in Annex II, except as otherwise provided therein, the following definitions apply:
‘type-approval’ means the procedure whereby an approval authority certifies that a type of vehicle, system, component or separate technical unit satisfies the relevant administrative provisions and technical requirements;
‘EU type-approval’ means the procedure whereby an approval authority certifies that a type of vehicle, system, component or separate technical unit satisfies the relevant administrative provisions and technical requirements of this Regulation;
‘national type-approval’ means the procedure whereby an approval authority certifies that a type of vehicle, system, component or separate technical unit satisfies the relevant administrative provisions and technical requirements laid down by the law of a Member State, the validity of such approval being restricted to the territory of that Member State;
‘type-approval certificate’ means the document whereby the approval authority officially certifies that a type of vehicle, system, component or separate technical unit is type-approved;
‘certificate of conformity’ means the document issued by the manufacturer which certifies that a produced vehicle conforms to the approved type of vehicle and complies with all regulatory acts that were applicable at the time of its production;
‘individual vehicle approval’ means the procedure whereby an approval authority certifies that a particular vehicle, whether unique or not, satisfies the relevant administrative provisions and technical requirements for EU individual vehicle approval or national individual vehicle approval;
‘whole-vehicle type-approval’ means the procedure whereby an approval authority certifies that an incomplete, complete or completed type of vehicle satisfies the relevant administrative provisions and technical requirements;
‘multi-stage type-approval’ means the procedure whereby one or more approval authorities certify that depending on its state of completion, an incomplete or completed type of vehicle satisfies the relevant administrative provisions and technical requirements;
‘step-by-step type-approval’ means the procedure consisting of the step-by-step collection of the whole set of EU type-approval certificates or UN type-approval certificates for the systems, components and separate technical units forming part of a vehicle, and which leads, in its final stage, to the whole-vehicle type-approval;
‘single-step type-approval’ means the procedure whereby an approval authority certifies, by means of a single operation, that a type of vehicle, system, component or separate technical unit as a whole satisfies the relevant administrative provisions and technical requirements;
‘mixed type-approval’ means a step-by-step type-approval for which one or more system type-approvals have been obtained during the final stage of the whole-vehicle type-approval, without the need to issue the EU type-approval certificates for those systems;
‘system type-approval’ means the procedure whereby an approval authority certifies that a type of system satisfies the relevant administrative provisions and technical requirements;
‘separate technical unit type-approval’ means the procedure whereby an approval authority certifies that a type of separate technical unit satisfies the relevant administrative provisions and technical requirements in relation to one or more specified types of vehicles;
‘component type-approval’ means the procedure whereby an approval authority certifies that a type of component independently of a vehicle satisfies the relevant administrative provisions and technical requirements;
‘vehicle’ means any motor vehicle or its trailer;
‘motor vehicle’ means any power-driven vehicle that is designed and constructed to be moved by its own means, that has at least four wheels, is complete, completed or incomplete, and has a maximum design speed exceeding 25 km/h;
‘trailer’ means any non-self-propelled vehicle on wheels designed and constructed to be towed by a motor vehicle, that can articulate at least around a horizontal axis perpendicular to the longitudinal median plane and around a vertical axis parallel to the longitudinal median plane of the towing motor vehicle;
‘system’ means an assembly of devices combined to perform one or more specific functions in a vehicle and that is subject to the requirements of this Regulation or any of the regulatory acts listed in Annex II;
‘component’ means a device that is intended to be part of a vehicle, that can be type-approved independently of a vehicle and that is subject to the requirements of this Regulation or any of the regulatory acts listed in Annex II where the specific regulatory act makes express provision to that effect;
‘separate technical unit’ means a device that is intended to be part of a vehicle that can be type-approved separately, but only in relation to one or more specified types of vehicle and that is subject to the requirements of this Regulation or any of the regulatory acts listed in Annex II where the specific regulatory act makes express provisions to that effect;
‘parts’ means goods used for the assembly, repair and maintenance of a vehicle, as well as spare parts;
‘equipment’ means goods other than parts that can be added to or installed on a vehicle;
‘spare parts’ means goods that are to be installed in or on a vehicle to replace original parts of that vehicle, including goods that are necessary for the use of a vehicle, with the exception of fuel;
‘base vehicle’ means any vehicle that is used at the initial stage of a multi-stage type-approval;
‘incomplete vehicle’ means any vehicle that must undergo at least one further stage of completion in order to meet the relevant technical requirements of this Regulation;
‘completed vehicle’ means a vehicle resulting from the multi-stage type-approval that meets the relevant technical requirements of this Regulation;
‘complete vehicle’ means a vehicle that does not need to be completed in order to meet the relevant technical requirements of this Regulation;
‘end-of-series vehicle’ means a vehicle that is part of a stock and that, due to the entry into force of new technical requirements against which it has not been type-approved, cannot or can no longer be made available on the market, registered or entered into service;
‘alternative-fuel vehicle’ means a vehicle designed to be capable of running on at least one type of fuel that is either gaseous at atmospheric temperature and pressure, or that is substantially derived from non-mineral oil;
‘vehicle produced in small series’ means a type of vehicle of which the number of units that are made available on the market, registered or entered into service do not exceed the quantitative annual limits laid down in Annex V;
‘special purpose vehicle’ means a vehicle of category M, N or O having specific technical features that enable it to perform a function that requires special arrangements or equipment;
‘type of vehicle’ means a particular group of vehicles that shares at least the features specified in Part B of Annex I, including a group of vehicles that contains variants and versions as referred to therein;
‘semi-trailer’ means a towed vehicle in which the axle, or axles are positioned behind the centre of gravity of the vehicle (when uniformly loaded), and which is equipped with a connecting device permitting horizontal and vertical forces to be transmitted to the towing vehicle;
‘market surveillance’ means the activities carried out and measures taken by the market surveillance authorities to ensure that vehicles, systems, components and separate technical units as well as parts and equipment made available on the market comply with the requirements set out in the relevant Union harmonisation legislation and do not endanger health, safety, the environment or any other aspect of public interest protection;
‘market surveillance authority’ means the national authority or authorities responsible for carrying out market surveillance on the territory of the Member State;
‘approval authority’ means the authority or authorities of a Member State, notified to the Commission by that Member State, with competence for all aspects of the type-approval of a vehicle, system, component or separate technical unit, or of the individual vehicle approval, for the authorisation process for parts and equipment, for issuing and, if appropriate, for withdrawing or refusing approval certificates, for acting as the contact point for the approval authorities of the other Member States, for designating the technical services, and for ensuring that the manufacturer meets its obligations regarding the conformity of production;
‘national authority’ means an approval authority or any other authority involved in and responsible for market surveillance, border control or registration in a Member State in respect of vehicles, systems, components, separate technical units, parts or equipment;
‘technical service’ means an organisation or body designated by the approval authority as a testing laboratory to carry out tests, or as a conformity assessment body to carry out the initial assessment and other tests or inspections;
‘national accreditation body’ means a national accreditation body as defined in point (11) of Article 2 of Regulation (EC) No 765/2008;
‘manufacturer’ means a natural or legal person who is responsible for all aspects of the type-approval of a vehicle, system, component or separate technical unit, or the individual vehicle approval, or the authorisation process for parts and equipment, for ensuring conformity of production and for market surveillance matters regarding that vehicle, system, component, separate technical unit, part and equipment produced, irrespective of whether or not that person is directly involved in all stages of the design and construction of that vehicle, system, component or separate technical unit concerned;
‘manufacturer's representative’ means any natural or legal person established in the Union who is duly appointed by the manufacturer to represent the manufacturer before the approval authority or the market surveillance authority and to act on the manufacturer's behalf in matters covered by this Regulation;
‘importer’ means a natural or legal person established in the Union who places on the market a vehicle, system, component, separate technical unit, part or equipment that has been manufactured in a third country;
‘distributor’ means a dealer or any other natural or legal person in the supply chain, other than the manufacturer or the importer, who makes available on the market a vehicle, system, component, separate technical unit, part or equipment;
‘economic operator’ means the manufacturer, the manufacturer's representative, the importer or the distributor;
‘independent operator’ means a natural or legal person, other than an authorised dealer or repairer, who is directly or indirectly involved in the repair and maintenance of vehicles, and include repairers, manufacturers or distributors of repair equipment, tools or spare parts, as well as publishers of technical information, automobile clubs, roadside assistance operators, operators offering inspection and testing services, operators offering training for installers, manufacturers and repairers of equipment for alternative-fuel vehicles; it also means authorised repairers, dealers and distributors within the distribution system of a given vehicle manufacturer to the extent that they provide repair and maintenance services for vehicles in respect of which they are not members of the vehicle manufacturer's distribution system;
‘authorised repairer’ means a natural or legal person who provides repair and maintenance services for vehicles and who operates within the manufacturer's distribution system;
‘independent repairer’ means a natural or legal person who provides repair and maintenance services for vehicles and who does not operate within the manufacturer's distribution system;
‘vehicle repair and maintenance information’ means all information, including all subsequent amendments and supplements thereto, that is required for diagnosing, servicing and inspecting a vehicle, preparing it for road worthiness testing, repairing, re-programming or re-initialising of a vehicle, or that is required for the remote diagnostic support of a vehicle or for the fitting on a vehicle of parts and equipment, and that is provided by the manufacturer to his authorised partners, dealers and repairers or is used by the manufacturer for the repair and maintenance purposes;
‘vehicle on-board diagnostic (OBD) information’ means the information generated by a system that is on board a vehicle or that is connected to an engine, and that is capable of detecting a malfunction, and, where applicable, is capable of signalling its occurrence by means of an alert system, is capable of identifying the likely area of malfunction by means of information stored in a computer memory, and is capable of communicating that information off-board;
‘placing on the market’ means making available a vehicle, system, component, separate technical unit, part or equipment for the first time in the Union;
‘making available on the market’ means any supply of a vehicle, system, component, separate technical unit, part or equipment for distribution or use on the market in the course of a commercial activity, whether in return for payment or free of charge;
‘entry into service’ means the first use, for its intended purpose, in the Union, of a vehicle, system, component, separate technical unit, part or equipment;
‘registration’ means an administrative authorisation for the entry into service in road traffic of an approved vehicle, involving the identification of the vehicle and the issuing to it of a serial number, known as the registration number, whether on a permanent or temporary basis;
‘virtual testing method’ means computer simulations, including calculations, to demonstrate that a vehicle, a system, a component or a separate technical unit fulfils the technical requirements of a regulatory act listed in Annex II without requiring the use of a physical vehicle, system, component or separate technical unit;
‘alternative requirements’ means administrative provisions and technical requirements that aim to ensure a level of functional safety, environmental protection and occupational safety that to the greatest extent practicable is equivalent to the level provided for by one or more of the regulatory acts listed in Annex II;
‘on-site assessment’ means a verification in the premises of a technical service or of one of its subcontractors or subsidiaries;
‘surveillance on-site assessment’ means a periodic routine on-site assessment that is neither the on-site assessment undertaken for the initial designation of the technical service or of one of its subcontractors or subsidiaries, nor the on-site assessment undertaken for the renewal of that designation;
‘date of manufacture of the vehicle’ means the date on which the manufacture of a vehicle was finalised in accordance with the approval obtained by the manufacturer.
Article 4
Vehicle categories
For the purposes of this Regulation, the following vehicle categories shall apply:
Category M consists of motor vehicles designed and constructed primarily for the carriage of passengers and their luggage, divided into:
|
(i) |
Category M1 : motor vehicles with not more than eight seating positions in addition to the driver's seating position and without space for standing passengers, regardless of whether the number of seating positions is restricted to the driver's seating position; |
|
(ii) |
Category M2 : motor vehicles with more than eight seating positions in addition to the driver's seating position and having a maximum mass not exceeding 5 tonnes, regardless of whether those motor vehicles have space for standing passengers; and |
|
(iii) |
Category M3 : motor vehicles with more than eight seating positions in addition to the driver's seating position and having a maximum mass exceeding 5 tonnes, regardless of whether those motor vehicles have space for standing passengers; |
Category N consists of motor vehicles designed and constructed primarily for the carriage of goods, divided into:
|
(i) |
Category N1 : motor vehicles with a maximum mass not exceeding 3,5 tonnes; |
|
(ii) |
Category N2 : motor vehicles with a maximum mass exceeding 3,5 tonnes but not exceeding 12 tonnes; and |
|
(iii) |
Category N3 : motor vehicles with a maximum mass exceeding 12 tonnes; |
Category O consists of trailers, divided into:
|
(i) |
Category O1 : trailers with a maximum mass not exceeding 0,75 tonnes; |
|
(ii) |
Category O2 : trailers with a maximum mass exceeding 0,75 tonnes but not exceeding 3,5 tonnes; |
|
(iii) |
Category O3 : trailers with a maximum mass exceeding 3,5 tonnes but not exceeding 10 tonnes; and |
|
(iv) |
Category O4 : trailers with a maximum mass exceeding 10 tonnes. |
The Commission is empowered to adopt delegated acts in accordance with Article 82, amending Annex I in relation to the types of vehicle and types of bodywork to take account of technical progress.
CHAPTER II
GENERAL OBLIGATIONS
Article 5
Technical requirements
Vehicles, systems, components and separate technical units shall be considered not to comply with this Regulation in the following cases in particular:
if they deviate from the particulars in the EU type-approval certificates and their attachments or from the descriptive particulars in the test reports more than is permitted in the relevant regulatory act;
if the performance criteria or limit values for series production laid down in the relevant regulatory act have not been fulfilled under all the conditions set out in the relevant regulatory act;
if any information given by the manufacturer in the information document is not reproducible under all the conditions set out in the relevant regulatory act by approval authorities, market surveillance authorities or the Commission.
Only checks, tests, inspections and assessments conducted by or carried out on behalf of the approval authorities, market surveillance authorities or the Commission shall be taken into account when assessing compliance for the purposes of this paragraph.
Article 6
Obligations of Member States
That notification shall include the name of those authorities, their address, including their electronic address, and their areas of responsibility. The Commission shall publish on its website a list and contact details of the approval authorities and the market surveillance authorities.
Member States shall ensure that their own approval authorities and market surveillance authorities adhere to a strict separation of roles and responsibilities and that they each function independently from each other. Those authorities may be within the same organisation provided that their activities are managed autonomously as part of separate structures.
By way of derogation from the first subparagraph of this paragraph, Member States may decide not to allow the circulation on the road, the placing on the market, the registration or the entry into service of vehicles that have been type-approved in accordance with this Regulation, but that exceed the harmonised dimensions, weights and axle loads laid down in Annex I to Council Directive 96/53/EC ( 4 ).
The Member States shall make accessible to the public a summary of the results of periodic reviews and assessments.
The Member States shall report to the Commission and the Forum on how they address any recommendations referred to in Article 11(5) issued by the Forum.
The Member States shall make accessible to the public a summary of the results of periodic reviews and assessments.
The Member States shall report to the Commission and the Forum on how they address any recommendations referred to in Article 11(5) issued by the Forum.
Article 7
Obligations of approval authorities
Approval authorities shall cooperate efficiently and effectively, and shall share information relevant to their role and functions.
Article 8
Obligations of market surveillance authorities
When carrying out such checks, market surveillance authorities shall take account of:
established principles of risk assessment;
substantiated complaints; and
any other relevant information, including the information exchanged in the Forum and testing results published by recognised third parties that meet the requirements laid down by the implementing acts referred to in Article 13(10).
Each test shall verify compliance with the applicable regulatory acts listed in Annex II.
Market surveillance authorities shall cooperate with economic operators regarding actions that could prevent or reduce the risks caused by vehicles, systems, components or separate technical units that those operators have made available on the market.
Article 9
Compliance verification by the Commission
The tests and inspections shall be performed, inter alia, by means of laboratory tests and on-road tests, on the basis of statistically relevant samples, and shall be supplemented by documentary checks.
When carrying out those tests and inspections, the Commission shall take account of:
established principles of risk assessment;
substantiated complaints; and
any other relevant information, including information exchanged in the Forum, testing results published by recognised third parties that meet the requirements laid down by the implementing acts referred to in Article 13(10), information concerning new technologies on the market and reports resulting from on-road remote sensing.
The Commission may entrust the performance of tests or inspections to technical services, in which case, the technical service shall be acting on behalf of the Commission. Where the Commission entrusts the performance of tests or inspections to technical services for the purposes of this Article, the Commission shall ensure that the technical service that is used is not the same as the technical service that performed the original type-approval test.
Those tests and inspections may take place:
on new vehicles supplied by manufacturers or other economic operator, as provided for in paragraph 2;
on registered vehicles with the agreement of the holder of the vehicle registration certificate.
The Member States shall cooperate with the Commission when the Commission carries out the tests and inspections.
Such data shall include all parameters and settings that are necessary to accurately replicate the test conditions that applied at the time of the type-approval testing. The Commission shall adopt implementing acts specifying the data that are to be made available, subject to the protection of commercial secrets and the preservation of personal data pursuant to Union and national law. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
Where the tests and inspections call into question the correctness of the type-approval itself, the Commission shall immediately inform the approval authority or authorities concerned as well as the Forum.
The Commission shall inform the relevant approval authorities and market surveillance authorities in order for them to take appropriate measures to alert users within the Union, within an adequate timeframe, of any non-compliance that it has identified in relation to any vehicle, system, component or separate technical unit so as to prevent or reduce the risk of injury or other damage.
The Commission shall make publicly available a report of its findings following any compliance verification testing it has carried out and shall forward its findings to the Member States and to the Forum. That report shall contain details of the vehicles, systems, components and separate technical units that were assessed and the identity of the manufacturer concerned, as well as a short description of the findings, including the nature of the non-compliance, if any.
Article 10
Assessments by the Commission
By way of derogation from the first subparagraph, the assessment of an approval authority may be less frequent if the Commission considers that the first assessment of that authority demonstrates that the procedures put in place ensure the effective application of this Regulation, taking into account the scope and range of EU type-approvals granted.
Article 11
Forum for Exchange of Information on Enforcement
The Forum shall be composed of representatives appointed by each Member State representing their approval authorities and market surveillance authorities.
Whenever appropriate, technical services, recognised third parties that meet the requirements laid down by the implementing acts referred to in Article 13(10), representatives of the European Parliament, of the industry and of the relevant economic operators, as well as of stakeholders involved in safety and environment matters, may be invited as observers to the Forum in accordance with the rules of procedures referred to in paragraph 7 of this Article.
The advisory tasks of the Forum shall have as their objective the promotion of best practices in order to facilitate the uniform interpretation and implementation of this Regulation, the exchange of information on enforcement problems, cooperation, in particular regarding the assessment, designation and monitoring of technical services, the development of working methods and tools, the development of an electronic information exchange procedure, and the evaluation of harmonised enforcement projects and penalties.
The Forum shall consider:
matters related to the uniform interpretation of the requirements laid down in this Regulation and in the regulatory acts listed in Annex II during implementation of those requirements;
the results of the activities relating to type-approval and market surveillance that were carried out by Member States in accordance with Article 6(8) and (9);
the results of tests and inspections carried out by the Commission in accordance with Article 9;
the assessments carried out by the Commission in accordance with Article 10;
test reports regarding possible non-compliance presented by recognised third parties that meet the requirements laid down by the implementing acts referred to in Article 13(10);
the results of the conformity of production activities carried out by approval authorities in accordance with Article 31;
the information submitted by Member States under Article 67(6) on their procedures for the assessment, designation and notification of technical services and for the monitoring of technical services;
matters of general relevance with regard to the implementation of the requirements laid down in this Regulation in relation to the assessment, designation and monitoring of technical services in accordance with Articles 67(10) and 78(4);
infringements by economic operators;
implementation of the corrective or restrictive measures laid down in Chapter XI;
the planning, coordination and results of market surveillance activities;
matters regarding access to vehicle OBD information and vehicle repair and maintenance information set out in Chapter XIV and, in particular, matters regarding the implementation of the procedures established under Article 65.
When expressing an opinion or issuing recommendations the Forum shall endeavour to reach a consensus. If no such consensus can be reached, the Forum shall express its opinion or issue its recommendations by a simple majority of the Member States. Each Member State shall have one vote. Member States with diverging positions may request that their positions and the grounds on which they are based be recorded in the Forum's opinion or recommendations.
Article 12
Online data exchange
The Commission and Member States shall use the Rapid Information System (RAPEX), established under Directive 2001/95/EC of the European Parliament and of the Council ( 5 ) and the Information and Communication System on Market Surveillance (ICSMS), established under Regulation (EC) No 765/2008 for market surveillance, recalls and other relevant activities between market surveillance authorities, Member States and the Commission.
From 5 July 2026, Member States shall make accessible to the public the information contained in the certificate of conformity, excluding vehicle identification numbers, as structured data in electronic format in the common secure electronic exchange system, in accordance with Article 37.
The Commission shall adopt implementing acts establishing the format of, and the criteria for public access to, the information referred to in the first and second subparagraphs of this paragraph. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The Commission shall adopt implementing acts establishing the format of, and the criteria for public access to, the information referred to in the first subparagraph of this paragraph. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
Article 13
General obligations of manufacturers
In the case of multi-stage type-approval, manufacturers shall also be responsible for the approval and conformity of production of the systems, components or separate technical units that they have added at the stage of vehicle completion. Manufacturers who modify components, systems or separate technical units already approved at earlier stages shall be responsible for the type-approval and conformity of production of the modified components, systems or separate technical units. Manufacturers of the previous stage shall provide information to manufacturers of the subsequent stage regarding any change that may affect component type-approval, system type-approval or separate technical unit type-approval or the whole-vehicle type-approval. Such information shall be provided as soon as the new extension to the whole-vehicle type-approval has been granted and at the latest on the starting date of manufacture of the incomplete vehicle.
Manufacturers shall keep a record of such complaints, including for each complaint a description of the issue and the details needed to precisely identify the affected type of vehicle, system, component, separate technical unit, part or equipment, and, in the case of substantiated complaints, manufacturers shall keep their distributors and importers informed thereof.
For the purposes of the first subparagraph of this paragraph, the Commission shall adopt implementing acts specifying the data to be made available free of charge, as well as the requirements to be met by third parties to demonstrate their legitimate interest in the fields of public safety or environmental protection and their recourse to adequate testing facilities. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
Article 14
Obligations of manufacturers concerning their vehicles, systems, components, separate technical units, parts and equipment that are not in conformity or that present a serious risk
The manufacturer shall immediately inform the approval authority that granted the type-approval in detail of the non-conformity and of any measures taken.
Manufacturers of a vehicle shall keep at the disposal of the approval authorities for a period of 10 years from the date of manufacture of the vehicle a copy of the certificates of conformity referred to in Article 36.
Manufacturers shall, following a reasoned request from a national authority, cooperate with that authority on any action taken in accordance with Article 20 of Regulation (EC) No 765/2008 to eliminate the risks posed by the vehicle, system, component, separate technical unit, part or equipment that they have made available on the market.
Article 15
Obligations of manufacturer's representatives
The manufacturer's representative shall perform the tasks specified in the mandate received from the manufacturer. That mandate shall at least, provide for the representative to:
have access to the EU type-approval certificate and its attachments referred to in Article 28(1), and to the certificate of conformity in one of the official Union languages; such documentation shall be made available to the approval authorities and to the market surveillance authorities for a period of 10 years after the end of the validity of the EU type-approval of a vehicle and for a period of five years after the end of validity of the EU type-approval of a system, component or separate technical unit;
provide an approval authority, following a reasoned request from that authority, with all information, documentation and any other technical specifications, including access to software and algorithms, that are necessary to demonstrate the conformity of production of a vehicle, system, component or separate technical unit;
cooperate with the approval authorities or the market surveillance authorities, at their request, on any action taken to eliminate the serious risk posed by vehicles, systems, components, separate technical units, parts or equipment covered by that mandate;
immediately inform the manufacturer about complaints and reports relating to risks, suspected incidents or non-compliance issues that relate to vehicles, systems, components, separate technical units, parts or equipment covered by that mandate;
have the right to terminate the mandate without penalty if the manufacturer acts contrary to its obligations under this Regulation.
The information to be provided shall specify at least:
the date of termination of the mandate;
the date until which the outgoing manufacturer's representative may be indicated in the information supplied by the manufacturer, including any promotional material;
the transfer of documents, including confidentiality aspects and property rights;
the obligation of the outgoing manufacturer's representative after the end of the mandate to forward to the manufacturer or incoming manufacturer's representative any complaints or reports about risks and suspected incidents relating to a vehicle, system, component, separate technical unit, part or equipment for which the outgoing manufacturer's representative had been designated as manufacturer's representative.
Article 16
Obligations of importers
In the case of a vehicle, the importer shall ensure that the vehicle is accompanied by the required certificate of conformity.
Article 17
Obligations of importers concerning their vehicles, systems, components, separate technical units, parts and equipment that are not in conformity or that present a serious risk
Importers shall also inform the approval authorities and market surveillance authorities of any action taken and give details, in particular of the serious risk and of any measure taken by the manufacturer.
Importers shall, following a reasoned request from a national authority, cooperate with that authority on any action taken in accordance with Article 20 of Regulation (EC) No 765/2008 to eliminate the risks posed by the vehicle, system, component, separate technical unit, part or equipment that they have made available on the market.
Article 18
Obligations of distributors
Article 19
Obligations of distributors concerning their vehicles, systems, components, separate technical units, parts and equipment that are not in conformity or that present a serious risk
Distributors shall also inform them of any action taken and give details of any measure taken by the manufacturer.
Article 20
Cases in which obligations of manufacturers apply to importers and distributors
An importer or distributor shall be considered a manufacturer for the purposes of this Regulation, and shall be subject to the obligations of the manufacturer under Articles 8, 13 and 14, in the following cases:
where the importer or distributor makes available on the market, or is responsible for the entry into service of a vehicle, system, component or separate technical unit under its name or trademark, or modifies a vehicle, system, component or separate technical unit in such a way that the vehicle, system, component or separate technical unit may no longer comply with the applicable requirements; or
where the importer or distributor makes available on the market or is responsible for the entry into service of a system, component or separate technical unit on the basis of a UN type-approval that was granted to a manufacturer outside the Union, and it is not possible to identify a manufacturer's representative in the territory of the Union.
Article 21
Identification of economic operators
Upon a request of an approval authority or a market surveillance authority, for a period of 10 years after the placing on the market of a vehicle and for a period of five years after the placing on the market of a system, component, separate technical unit, part or equipment, economic operators shall provide information on the following:
the identity of any economic operator that has supplied them with a vehicle, system, component, separate technical unit, part or equipment;
the identity of any economic operator to which they have supplied a vehicle, system, component, separate technical unit, part or equipment.
CHAPTER III
PROCEDURES FOR EU TYPE-APPROVAL
Article 22
Procedures for EU type-approval
Where applying for a whole-vehicle type-approval, the manufacturer may choose one of the following procedures:
step-by-step type-approval;
single-step type-approval;
mixed type-approval.
In addition, the manufacturer may choose a multi-stage type-approval for an incomplete or completed vehicle.
Multi-stage type-approval shall also apply to complete vehicles that have been converted or modified by another manufacturer after their completion.
Article 23
Application for EU type-approval
A new application may not be submitted in another Member State in respect of the same type of vehicle, system, component or separate technical unit where:
an approval authority has refused to grant a type-approval of that type;
an approval authority has withdrawn type-approval of that type; or
the manufacturer has revoked an application for a type-approval of that type.
The approval authority shall reject an application for a type-approval of a different type designation or of a modification with respect to a previous application where the changes are not sufficient to constitute a new type of vehicle, system, component or separate technical unit.
An application for an EU type-approval of a particular type of vehicle, system, component or separate technical unit shall include a declaration by the manufacturer certifying, in accordance with the second subparagraph of paragraph 2 that:
the manufacturer has not applied for an EU type-approval for the same type to any other approval authority, and no other approval authority granted the manufacturer such an approval;
no approval authority has refused to grant type-approval of that type;
no approval authority has withdrawn type-approval of that type; and
the manufacturer has not revoked an application for a type-approval of that type.
Article 24
Information folder
The information folder shall include the following:
an information document, in accordance with the template laid down in the implementing acts referred to in paragraph 4, for single-step type-approval or mixed whole-vehicle type-approval or for step-by-step whole-vehicle type-approval or, in the case of the type-approval of a system, component or separate technical unit, in accordance with the relevant regulatory act listed in Annex II;
all data, drawings, photographs and other relevant information;
for vehicles, an indication of the procedure or procedures chosen in accordance with Article 22(1);
any additional information requested by the approval authority in the context of the EU type-approval procedure.
Article 25
Additional information to be provided with an application for EU type-approval
In the case of a system type-approval, a component type-approval or a separate technical unit type-approval, pursuant to the regulatory acts listed in Annex II, the approval authority shall have access to the information folder and, if applicable, the EU type-approval certificates and their attachments until the whole-vehicle type-approval is either granted or refused.
For systems for which no EU type-approval certificate or UN type-approval certificate has been presented, the application shall be accompanied, in addition to the information folder referred to in Article 24, by the information required for the approval of those systems during the vehicle approval phase, and by a test report instead of the EU type-approval certificate or UN type-approval certificate.
An application for a multi-stage type-approval shall be accompanied by the following information:
in the first stage, by those parts of the information folder and the EU type-approval certificates, UN type-approval certificates or, if applicable, the test reports, that are relevant to the state of completion of the base vehicle;
in the second and subsequent stages, by those parts of the information folder and the EU type-approval certificates or UN type-approval certificates that are relevant to the current stage of completion, together with a copy of the EU whole-vehicle type-approval certificate that was issued at the preceding stage of construction, as well as full details of any changes or additions that the manufacturer has made to the vehicle.
The information specified in this paragraph shall be supplied in accordance with Article 24(3).
The approval authority and technical services may also require the manufacturer to supply documentation or any additional information needed to allow the approval authority or technical services to develop an appropriate level of understanding of the systems, including the system development process and the system concept, as well as the functions of software and algorithms that are necessary to verify compliance with the requirements of this Regulation, to take a decision on which tests are required or to facilitate the execution of those tests.
CHAPTER IV
CONDUCT OF PROCEDURES FOR EU TYPE-APPROVAL
Article 26
General provisions on conduct of procedures for EU type-approval
An approval authority, having received an application in accordance with Article 23, shall only grant an EU type-approval after having verified all of the following:
the conformity of production arrangements referred to in Article 31;
that the declaration referred to in Article 23(3) has been submitted;
the compliance of the type of vehicle, system, component or separate technical unit with the applicable requirements;
in the case of whole-vehicle type-approvals in accordance with the step-by-step, mixed or multi-stage type-approval procedures, the approval authority shall verify, in accordance with Article 22(4), that the systems, components and separate technical units are covered by separate and valid type-approvals that have been granted pursuant to the requirements applicable at the time of the granting of the whole-vehicle type-approval.
The Commission is empowered to adopt delegated acts in accordance with Article 82, amending Annexes III and IX to take into account regulatory and technological developments by updating the procedures therein with respect to EU type-approval and multi-stage type-approval.
The information package may be kept electronically. It shall contain an index that clearly indicates all of the pages and the format of each document, and that chronologically records any changes to the EU type-approval.
The approval authority shall keep the information package available for a period of 10 years after the end of the validity of the EU type-approval concerned.
The approval authority shall ask the approval authorities that granted type-approvals for the systems, components, or separate technical units, to act in accordance with Article 54(2).
Article 27
Notification of EU type-approval granted, amended, refused and withdrawn
Article 28
EU type-approval certificate
The EU type-approval certificate shall contain the following attachments:
the information package referred to in Article 26(4);
the test reports referred to in Article 30 in the case of a system, component or separate technical unit type-approval, or the test results sheet in the case of whole-vehicle type-approval;
in the case of the whole-vehicle type-approval, the name and the specimen of the signature of the person or persons authorised to sign the certificates of conformity and a statement of their position in the company;
in the case of the whole-vehicle type-approval, a filled-out specimen of the certificate of conformity of the vehicle type.
In respect of each type of vehicle, system, component and separate technical unit, the approval authority shall:
complete all the relevant sections of the EU type-approval certificate, including its attachments;
compile the index to the information package as referred to in Article 26(4);
issue the completed EU type-approval certificate and its attachments to the manufacturer without delay.
Article 29
Specific provisions concerning EU type-approvals for systems, components and separate technical units
In such cases, the EU type-approval certificate shall specify any restrictions on the use of the component or the separate technical unit, and shall indicate the special conditions for fitting that component or separate technical unit in a vehicle.
Where that component or separate technical unit is fitted in a vehicle, the approval authority shall verify, at the time of the approval of the vehicle, that the component or separate technical unit complies with all applicable restrictions on the use or conditions for fitting.
Article 30
Tests required for EU type-approval
Article 31
Conformity of production arrangements
In accordance with Annex IV, the approval authority shall take the necessary measures to carry out such checks or tests with the frequency set out in the regulatory acts listed in Annex II, or, if no frequency is specified in those acts, at least once every three years.
In order to verify that a vehicle, system, component or separate technical unit conforms to the approved type, the approval authority or the technical services shall:
if a range of values is provided for in the test procedures laid down in the relevant regulatory acts listed in Annex II, set the values in a random manner within the provided range when carrying out checks or tests; and
have access to the software, algorithms, documentation and any additional information in accordance with Article 25(4).
Article 32
Fees
The Member State shall ensure that sufficient resources are available to cover the costs for market surveillance activities. Without prejudice to national law, those costs may be recovered by fees that can be levied by the Member State in which the vehicles are placed on the market.
CHAPTER V
AMENDMENTS TO AND VALIDITY OF EU TYPE-APPROVALS
Article 33
General provisions on amendments of EU type-approvals
The approval authority shall decide whether that change requires an amendment, in the form of either a revision or an extension of the EU type-approval in accordance with Article 34, or whether that change requires a new EU type-approval.
Article 34
Revisions and extensions of EU type-approvals
In such case, the approval authority shall issue the revised pages of the information package as necessary and without delay, marking each revised page to show clearly the nature of the change and the date of reissue, or it shall issue a consolidated, updated version of the information package, accompanied by a detailed description of the changes.
The amendment shall be designated an ‘extension’ where the approval authority finds that the particulars recorded in the information package have changed, and where any of the following apply:
further inspections or tests are required to verify continued compliance with the requirements upon which the existing EU type-approval has been based;
any information on the EU type-approval certificate, except for its attachments, has changed; or
new requirements under any regulatory act listed in Annex II become applicable to the approved type of vehicle, system, component or separate technical unit.
In the event of an extension, the approval authority shall issue an updated EU type-approval certificate without delay, which shall be denoted by an extension number that is incremented in accordance with the number of successive extensions already granted. That approval certificate shall clearly state the reason for the extension, the date of reissue and, where relevant, the period of validity.
Article 35
Termination of validity
Where the approval authority carries out the verification referred to in the first subparagraph of this paragraph, it is not necessary for the tests referred to in Article 30 to be repeated.
An EU type-approval shall become invalid in each of the following cases:
where new requirements applicable to the approved type of vehicle, system, component or separate technical unit become mandatory for the making available on the market, registration or entry into service and the EU type-approval cannot be extended on the grounds laid down in point (c) of Article 34(2);
where a verification carried out in accordance with paragraph 1 of this Article concludes that the vehicle does not comply with all the regulatory acts that are relevant to that type;
where the production of vehicles in conformity with the approved type of vehicle is definitively discontinued on a voluntary basis, which shall be deemed to have occurred where no vehicle of the type concerned has been produced in the previous two years; however, such type-approvals shall continue to be valid for the purpose of registration or entry into service as long as point (a) of this paragraph is not applicable;
where the EU type-approval has been withdrawn in accordance with Article 31(7);
where the validity of the EU type-approval certificate expires due to a restriction referred to in Article 39(6);
where the type-approval was found to be based on false declarations, falsified test results or where data were withheld which would have led to the refusal to grant the type-approval.
Within one month of receiving the notification referred to in the first subparagraph, the approval authority that granted the EU type-approval for the type of vehicle, system, component, or separate technical unit, shall inform the approval authorities of the other Member States accordingly.
In the case of vehicles, the communication referred to in the first subparagraph of this paragraph shall specify the date of manufacture and the vehicle identification number (‘VIN’), as defined in point (2) of Article 2 of Commission Regulation (EU) No 19/2011 ( 6 ), of the last vehicle produced.
CHAPTER VI
CERTIFICATE OF CONFORMITY AND MARKINGS
Article 36
Certificate of conformity in paper format
The certificate of conformity in paper format shall describe the main characteristics of the vehicle, as well as its technical performance in concrete terms. The certificate of conformity in paper format shall include the date of manufacture of the vehicle. The certificate of conformity in paper format shall be designed in such a way as to prevent forgery.
The certificate of conformity in paper format shall be delivered free of charge to the buyer, together with the vehicle. Its delivery may not be made dependent on an explicit request or on the submission of additional information to the manufacturer.
The Commission shall adopt implementing acts concerning the certificate of conformity in paper format, setting out, in particular:
the template for the certificate of conformity;
the security elements to prevent forgery of the certificate of conformity; and
the specification concerning the manner of signing of the certificate of conformity.
Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2). The first such implementing act shall be adopted before 1 September 2020.
Article 37
Certificate of conformity in electronic format
Taking into account the data that are required to be provided on the certificate of conformity in paper format, the Commission shall adopt implementing acts concerning certificates of conformity as structured data in electronic format setting out, in particular:
the basic format and structure of the data elements of the certificates of conformity in electronic format and the messages used in the exchange;
minimum requirements for secure data exchange, including the prevention of data corruption and data misuse, and measures to guarantee the authenticity of the electronic data, such as the use of digital signature;
the means of exchange of the data of the certificate of conformity in electronic format;
the minimum requirements for a vehicle-specific unique identifier and the form of information for the buyer in accordance with paragraph 5;
the read-only access referred to in paragraph 5;
exemptions for manufacturers of particular vehicle categories and types of vehicle that are produced in small series.
Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2). The first such implementing act shall be adopted before 1 September 2020.
Article 38
Manufacturer's statutory and additional plates, markings and type-approval mark of components and separate technical units
Where no such type-approval mark is required, the manufacturer shall affix at least the trade name or trade mark of the manufacturer, as well as the type number or an identification number, to the component or separate technical unit.
CHAPTER VII
NEW TECHNOLOGIES OR NEW CONCEPTS
Article 39
Exemptions for new technologies or new concepts
The approval authority shall grant the EU type-approval referred to in paragraph 1 where all of the following conditions are met:
the application for the EU type-approval states the reasons why the new technologies or new concepts make the vehicles, systems, components or separate technical units incompatible with one or more regulatory acts listed in Annex II;
the application for the EU type-approval describes the safety and environmental implications of the new technology or new concept and the measures taken in order to ensure at least an equivalent level of safety and environmental protection to that provided by the requirements in respect of which an exemption is sought;
test descriptions and results are presented proving that the condition in point (b) is met.
The Commission shall adopt implementing acts to decide whether to grant the authorisation referred to in the first subparagraph of this paragraph. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The provisional nature and the limited territorial validity of the EU type-approval shall be apparent from the heading of the EU type-approval certificate and the heading of the certificate of conformity.
However, vehicles that have been manufactured in conformity with the provisional EU type-approval before it ceased to be valid may be placed on the market, be registered or enter into service in any Member State that has accepted the provisional EU type-approval in accordance with paragraph 5.
Article 40
Subsequent adaptation of regulatory acts
Where the exemption under Article 39 relates to a UN Regulation, the Commission shall make proposals to amend the relevant UN Regulation in accordance with the procedure applicable under the Revised 1958 Agreement.
CHAPTER VIII
VEHICLES PRODUCED IN SMALL SERIES
Article 41
EU type-approval of vehicles produced in small series
Article 42
National type-approval of vehicles produced in small series
Article 43
Validity of a national type-approval of vehicles produced in small series
The national authority of the other Member State shall permit the placing on the market, registration or entry into service of such vehicle, unless it has reasonable grounds to believe that the national technical requirements in accordance with which the type of vehicle has been approved are not equivalent to its own.
CHAPTER IX
INDIVIDUAL VEHICLE APPROVALS
Article 44
EU individual vehicle approvals
This Chapter shall not apply to incomplete vehicles.
Article 45
National individual vehicle approvals
Article 46
Validity of national individual vehicle approvals
Article 47
Specific provisions
CHAPTER X
MAKING AVAILABLE ON THE MARKET, REGISTRATION OR ENTRY INTO SERVICE
Article 48
Making available on the market, registration or entry into service of vehicles other than end-of-series vehicles
Registration and entry into service of incomplete vehicles may be refused as long as the vehicles remain incomplete. Registration and entry into service of incomplete vehicles shall not be used to circumvent the application of Article 49.
Article 49
Making available on the market, registration or entry into service of end-of-series vehicles
The first subparagraph shall apply only to vehicles within the territory of the Union which were covered by a valid EU type-approval at the time of their production and which had not been registered or entered into service before that EU type-approval lost its validity.
The Member States concerned shall decide, within three months of receiving such a request, whether to permit the registration or the entry into service of those vehicles within their territory, and if so, the number of such vehicles.
Article 50
Making available on the market or entry into service of components and separate technical units
CHAPTER XI
SAFEGUARD CLAUSES
Article 51
National evaluation regarding vehicles, systems, components and separate technical units suspected of presenting a serious risk or non-compliance
Where, based on their own market surveillance activities, or based on information provided by an approval authority or a manufacturer or based on complaints, the market surveillance authorities of one Member State have sufficient reasons to believe that a vehicle, system, component or separate technical unit presents a serious risk to the health or safety of persons or to other aspects of the protection of public interests covered by this Regulation or does not comply with the requirements laid down in this Regulation, they shall evaluate the vehicle, system, component or separate technical unit concerned with respect to the relevant requirements laid down in this Regulation. The relevant economic operators and the relevant approval authorities shall cooperate fully with the market surveillance authorities, which shall include forwarding the results of all relevant checks or tests performed in accordance with Article 31.
Article 20 of Regulation (EC) No 765/2008 shall apply to the risk assessment of the vehicle, system, component or separate technical unit concerned.
Article 52
National procedures for dealing with vehicles, systems, components and separate technical units presenting a serious risk or non-compliance
Economic operators shall, in accordance with the obligations set out in Articles 13 to 21, ensure that all appropriate corrective measures are taken in respect of all concerned vehicles, systems, components or separate technical units that they have placed on the market, registered or entered into service in the Union.
Article 21 of Regulation (EC) No 765/2008 shall apply to the restrictive measures referred to in the first subparagraph of this paragraph.
Article 53
Corrective and restrictive measures at Union level
The information provided shall include all available details, in particular the data necessary for the identification of the concerned vehicle, system, component or separate technical unit, its origin, the nature of the alleged non-compliance and the risk involved, the nature and duration of the national corrective and restrictive measures taken, and the arguments put forward by the relevant economic operator.
The Member State that takes the corrective or restrictive measure shall also indicate whether the risk or the non-compliance is due to the following:
the failure of the vehicle, system, component or separate technical unit to meet requirements relating to the health or safety of persons, to the protection of the environment or to other aspects of the protection of public interests covered by this Regulation; or
shortcomings in the relevant regulatory acts listed in Annex II.
On the basis of the consultation referred to in the first subparagraph of this paragraph, the Commission shall adopt implementing acts to decide on harmonised corrective or restrictive measures at Union level. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The Commission shall immediately communicate the decision referred to in the second subparagraph to the relevant economic operator or operators. Member States shall implement such acts without delay and shall inform the Commission accordingly.
Where the Commission considers that a notified national measure is unjustified, the Member State concerned shall withdraw or adapt the measure, in accordance with the Commission decision referred to in the second subparagraph.
On the basis of consultation referred to in the first subparagraph of this paragraph, the Commission shall adopt implementing acts to decide on corrective or restrictive measures at Union level. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The Commission shall immediately communicate the decision referred to in the second subparagraph to the relevant economic operator or operators. Member States shall implement such acts without delay and shall inform the Commission accordingly.
Where the risk or non-compliance is attributed to shortcomings in regulatory acts listed in Annex II, the Commission shall propose appropriate measures as follows:
where legal acts of the Union are concerned, the Commission shall propose the necessary amendments to the acts concerned;
where UN Regulations are concerned, the Commission shall propose the necessary draft amendments to the relevant UN Regulations in accordance with the procedure applicable under the Revised 1958 Agreement.
Article 54
Non-compliant EU type-approval
The Commission shall immediately communicate the decision referred to in the first subparagraph to the relevant economic operators. The Member States shall implement such acts without delay and shall inform the Commission accordingly.
On the basis of consultations referred to in the first subparagraph of this paragraph the Commission shall adopt an implementing act to decide on the refusal of the recognition of type-approval referred to in paragraph 1 of this Article. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
Article 55
Placing on the market and entry into service of parts or equipment that may pose a serious risk to the correct functioning of essential systems
Those requirements may be based on the regulatory acts listed in Annex II or may consist of a comparison of the environmental or safety performance of the parts or equipment with the environmental or safety performance of the original parts or equipment, as appropriate. In either case, the requirements shall ensure that the parts or equipment do not impair the functioning of the systems that are essential for the safety of the vehicle or for its environmental performance.
The Commission is empowered to adopt delegated acts in accordance with Article 82, amending Annex VI to take account of technical and regulatory developments by laying down and updating the list of parts or equipment on the basis of an evaluation of the following:
the extent to which there exists a serious risk to the safety or environmental performance of vehicles that are fitted with the parts or equipment in question;
the potential effect on consumers and aftermarket manufacturers of a possible authorisation of the parts or equipment under Article 56(1).
For the purposes of this Article, original parts or equipment means parts or equipment that are manufactured according to the specifications and production standards provided by the vehicle manufacturer for the assembly of the vehicle in question.
Article 56
Related requirements for parts or equipment that may pose a serious risk to the correct functioning of essential systems
The approval authority shall authorise the placing on the market and the entering into service of the parts or equipment where it finds, taking into account the test report referred to in paragraph 1 of this Article and other evidence, that the parts or equipment in question comply with the requirements referred to in Article 55(3).
The approval authority shall issue to the manufacturer an authorisation certificate without delay.
The Commission shall adopt implementing acts laying down the template and the numbering system for the authorisation certificate referred to in the third subparagraph of this paragraph. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The manufacturer shall ensure that the parts or equipment are produced and continue to be produced under the conditions under which the authorisation has been issued.
Where the approval authority finds that the conditions for issuing the authorisation are no longer fulfilled, it shall request the manufacturer to take the necessary measures to ensure that the parts or equipment are brought into conformity. Where necessary, it shall withdraw the authorisation.
CHAPTER XII
INTERNATIONAL REGULATIONS
Article 57
UN Regulations required for EU type-approval
Those delegated acts shall specify the dates from which that UN Regulation or amendments are to be compulsory, and shall include transitional provisions, where appropriate, and, where applicable for the purposes of EU type-approval, first registration and entry into service of vehicles and making available on the market of systems, components and separate technical units.
Article 58
Equivalence of UN Regulations for the purpose of EU type-approval
CHAPTER XIII
PROVISION OF TECHNICAL INFORMATION
Article 59
Information intended for users
Article 60
Information intended for manufacturers
Manufacturers of vehicles may impose a binding agreement on the manufacturers of systems, components, separate technical units, parts or equipment to protect the confidentiality of any information that is not in the public domain, including information related to intellectual property rights.
CHAPTER XIV
ACCESS TO VEHICLE OBD INFORMATION AND VEHICLE REPAIR AND MAINTENANCE INFORMATION
Article 61
Manufacturers' obligations to provide vehicle OBD information and vehicle repair and maintenance information
Manufacturers shall provide a standardised, secure and remote facility to enable independent repairers to complete operations that involve access to the vehicle security system.
The vehicle OBD information and the vehicle repair and maintenance information shall be made available on the websites of manufacturers using a standardised format or, if this is not feasible, due to the nature of the information, in another appropriate format. For independent operators other than repairers, the information shall also be given in a machine-readable format that is capable of being electronically processed with commonly available information technology tools and software and which allows independent operators to carry out the task associated with their business in the aftermarket supply chain.
However, in the following cases, it shall be sufficient that the manufacturer provides the required information promptly in an easily accessible manner when an independent operator so requests:
for vehicle types covered by a national type-approval of vehicles produced in small series as referred to in Article 42;
for special purpose vehicles;
for vehicle types of categories O1 and O2 that do not use diagnostic tools or a physical or wireless communication with the on-board electronic control unit or units for the purpose of diagnostics or reprogramming of their vehicles;
for the final stage of type-approval in a multi-stage type-approval procedure, where the final stage only covers bodywork which does not contain electronic vehicle control systems, and all electronic vehicle control systems of the base vehicle remain unchanged.
Manufacturers shall make any subsequent amendments and supplements to vehicle OBD information and vehicle repair and maintenance information available on their websites at the same time they are made available to authorised repairers.
Article 62
Obligations with regard to holders of several type-approvals
Article 63
Fees for access to vehicle repair and maintenance information
In addition to time-based access, manufacturers may offer transaction-based access for which fees are charged per transaction and not based on the duration for which access is granted.
Where the manufacturer offers both systems of access, independent repairers shall choose systems of access, which may be either time-based or transaction-based.
Article 64
Proof of compliance with vehicle OBD information and repair and maintenance information obligations
Article 65
Compliance with the obligations regarding access to vehicle OBD information and vehicle repair and maintenance information
Those measures may include the withdrawal or suspension of the type-approval, fines or other measures adopted pursuant to Article 84.
Article 66
Forum on Access to Vehicle Information
It shall carry out its activities in accordance with Annex X to this Regulation.
The Commission may decide to keep the discussions and findings of the Forum on Access to Vehicle Information confidential.
CHAPTER XV
ASSESSMENT, DESIGNATION, NOTIFICATION AND MONITORING OF TECHNICAL SERVICES
Article 67
Type-approval authority responsible for technical services
Peer evaluations shall cover the assessments of the entire or partial operations of technical services that have been carried out by type-approval authorities in accordance with Article 73(4), including the competence of the personnel, the correctness of the test and inspection methodology and the correctness of test results based on a defined scope of regulatory acts listed in Part I of Annex II.
Activities related to the assessment and monitoring of technical services that only deal with national individual approvals that were granted in accordance with Article 45 or with national type-approvals of vehicles produced in small series that were granted in accordance with Article 42 are exempted from peer evaluations
Any assessment of accredited technical services by type-approval authorities shall be exempt from peer evaluations.
The Commission may adopt implementing acts laying down the model for the provision of information on the procedures of the Member States referred to in the first subparagraph of this paragraph. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The Commission may decide to participate in the peer-evaluation team on the basis of a risk assessment analysis.
The peer-evaluation shall be carried out under the responsibility of the approval authority that is subject to evaluation, and shall include a visit to the premises of a technical service selected at the discretion of the peer-evaluation team.
Type-approval authorities that are not subject to peer-evaluation in accordance with paragraph 3 shall not be included in any of the activities related to the peer-evaluation team.
Article 68
Designation of technical services
The type-approval authorities shall designate technical services for one or more of the following categories of activities, depending on their field of competence:
category A: tests referred to in this Regulation and in the regulatory acts listed in Annex II that technical services carry out in their own facilities;
category B: the supervision of the tests, which includes test preparation, referred to in this Regulation and in the regulatory acts listed in Annex II, where such tests are performed at the manufacturer's facilities or at the facilities of a third party;
category C: the assessment and monitoring on a regular basis of the procedures of the manufacturer for controlling the conformity of production;
category D: the supervision or performance of tests or inspections for the surveillance of the conformity of production.
Article 69
Independence of the technical services
An organisation or body that belongs to a trade association or to a professional federation representing undertakings that are involved in the design, manufacturing, supply or maintenance of the vehicles, systems, components or separate technical units that it assesses, tests or inspects, may be considered as fulfilling the requirements of the first subparagraph, provided that its independence and the absence of any conflict of interest are demonstrated to the type-approval authority of the relevant Member State.
Article 70
Competence of the technical services
A technical service shall be capable of carrying out all the activities for which it is applying to be designated in accordance with Article 68(1). It shall demonstrate to the type-approval authority or to the national accreditation body carrying out the assessment or monitoring of that technical service that it satisfies all of the following conditions:
its personnel have the appropriate skills, the specific technical knowledge, the vocational training and sufficient and appropriate experience to perform the activities for which it is applying to be designated;
it possesses descriptions of the procedures relevant for the performance of the activities for which it is applying to be designated, taking due account of the degree of complexity of the technology of the relevant vehicle, system, component or separate technical unit in question, as well as the mass or serial nature of the production process. The technical service shall demonstrate the transparency and reproducibility of those procedures;
it has the necessary means to perform the tasks connected with the category or categories of activities for which it is applying to be designated, and it has access to all necessary equipment or facilities.
Article 71
Subsidiaries of and subcontracting by technical services
Article 72
In-house technical service of the manufacturer
An in-house technical service referred to in paragraph 1 shall comply with the following requirements:
it has been accredited by a national accreditation body and complies with the requirements laid down in Appendices 1 and 2 to Annex III;
the in-house technical service, including its personnel, is organisationally identifiable and has reporting methods within the manufacturer's company of which they form part that ensures its impartiality and demonstrates that impartiality to the relevant type-approval authority and to the national accreditation body;
neither the in-house technical service nor its personnel is engaged in any activity that might conflict with its independence or with its integrity to perform the activities for which it has been designated;
it supplies its services only to the manufacturer's company of which it forms part.
Article 73
Assessment and designation of technical services
Where the technical service applies to be designated in a Member State other than the Member State of its establishment, one of the representatives of the joint assessment team shall be from the type-approval authority of the Member State of its establishment, unless that type-approval authority decides against participating in the joint assessment team.
The joint assessment team shall participate in the assessment of the applicant technical service, including the on-site assessment. The designating type-approval authority of the Member State in which the applicant technical service has requested to be designated shall give the joint assessment team all necessary assistance and provide timely access to all documentation necessary to assess the applicant technical service.
Article 74
Notification to the Commission concerning designation of technical services
Such notification shall be made before the designated technical service concerned conducts any activity referred to in Article 68(1).
Article 75
Changes to and renewal of designations of technical services
The type-approval authority shall immediately notify to the Commission and the type-approval authorities of the other Member States any restriction, suspension or withdrawal of a designation.
The Commission shall update the list referred to in Article 74(3) accordingly.
Within two months after having notified the changes to the designation, the type-approval authority shall submit a report on its findings regarding the non-compliance to the Commission and the other type-approval authorities. Where necessary to ensure the safety of vehicles, systems, components or separate technical units already placed on the market, the designating type-approval authority shall instruct the type-approval authorities concerned to suspend or withdraw within a reasonable period of time, any EU type-approval certificates which were unduly issued.
Extensions of the scope of a technical service's designation only for the regulatory acts listed in Annex II may be carried out in accordance with the procedures laid down in Appendix 2 to Annex III, and subject to the notification referred to in Article 74.
Article 76
Monitoring of technical services
The first subparagraph of this paragraph shall not apply to any activities of technical services which are monitored by accreditation bodies in accordance with Article 67(1) for the purposes of ensuring compliance with the requirements laid down in Articles 68 to 72, in Articles 80 and 81 and in Appendix 2 to Annex III.
Technical services shall supply on request all relevant information and documents that are required to enable the designating type-approval authority or national accreditation body to verify compliance with those requirements.
Technical services shall inform the designating type-approval authority or national accreditation body without delay of any changes, in particular regarding their personnel, facilities, subsidiaries or subcontractors, which may affect compliance with the requirements set out in Articles 68 to 72, in Articles 80 and 81 and in Appendix 2 to Annex III, or their ability to perform the conformity assessment tasks relating to the vehicles, systems, components and separate technical units for which they have been designated.
Where that type-approval authority acknowledges a legitimate reason, it shall inform the Commission thereof.
The Commission shall consult the Member States without delay. On the basis of that consultation, the Commission shall adopt implementing acts to decide if the legitimate reason is justified or not. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2).
The technical service and the designating type-approval authority may request that any information that is transmitted to the type-approval authority of another Member State or to the Commission shall be treated confidentially.
Within two months after finalising the assessment of the technical service, each Member State shall report to the Commission and to the other Member States on its monitoring activities. Those reports shall contain a summary of the assessment, which shall be made publicly available.
Article 77
Challenge to the competence of technical services
The Commission shall investigate the responsibility of the technical service in the case where it is demonstrated or where there are justified grounds for considering that a type-approval has been granted on the basis of false data, that the test results have been falsified or that data or technical specifications have been withheld that would have led to the refusal to grant the type-approval.
The Commission shall request that Member State to take restrictive measures, including the restriction, suspension or withdrawal of the designation, where necessary.
Where a Member State fails to take the necessary restrictive measures, the Commission may adopt implementing acts to decide to restrict, suspend or withdraw the designation of the technical service concerned. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 83(2). The Commission shall notify the Member State concerned of those implementing acts and shall update the information published referred to in Article 74(3) accordingly.
Article 78
Exchange of information on assessment, designation and monitoring of technical services
The exchange of information shall be coordinated by the Forum.
Article 79
Cooperation with national accreditation bodies
Article 80
Operational obligations of technical services
At all times, technical services shall:
allow the designating type-approval authority to witness the performance of the technical service during testing for type-approval; and
where requested, provide the designating type-approval authority with information on the categories of activities for which they have been designated.
Article 81
Information obligations of technical services
Technical services shall inform the designating type-approval authority of the following:
any non-conformity encountered which may require the refusal, restriction, suspension or withdrawal of a type-approval certificate;
any circumstances affecting the scope of and conditions for their designation;
any request for information which they have received from market surveillance authorities regarding their activities.
CHAPTER XVI
DELEGATED AND IMPLEMENTING POWERS
Article 82
Exercise of the delegation
Article 83
Committee procedure
Where the committee delivers no opinion, the Commission shall not adopt the draft implementing act and the third subparagraph of Article 5(4) of Regulation (EU) No 182/2011 shall apply.
CHAPTER XVII
FINAL PROVISIONS
Article 84
Penalties
The types of infringements by economic operators and technical services subject to penalties shall be at least the following:
making false declarations during approval procedures or corrective or restrictive measures being imposed in accordance with Chapter XI;
falsifying test results for type-approval or for market surveillance;
withholding data or technical specifications that could lead to the recall of vehicles, systems, components and separate technical units, or to the refusal or withdrawal of EU type-approval certificate;
non-compliance by technical services in respect of the requirements for their designation.
In addition to the types of infringements set out in paragraph 2, the types of infringements by economic operators that are also subject to penalties shall be at least the following:
refusing to provide access to information;
making available on the market vehicles, systems, components or separate technical units subject to approval without such approval or falsifying documents, certificates of conformity, statutory plates or approval marks with that intention.
Article 85
Administrative fines in support of corrective and restrictive measures at Union level
The administrative fines imposed by the Commission shall not be in addition to the penalties imposed by the Member States in accordance with Article 84 for the same infringement. The administrative fines imposed by the Commission shall not exceed EUR 30 000 per non-compliant vehicle, system, component or separate technical unit.
The Commission may not bring, start afresh or continue proceedings under this Article against economic operators for infringements of this Regulation for which the concerned economic operators have been penalised or declared not liable in accordance with Article 84 by an earlier decision that can no longer be challenged.
The delegated acts referred to in paragraph 2 shall respect the following principles:
the procedure by the Commission shall respect the right to good administration, and in particular the right to be heard and the right to have access to the file, while respecting the legitimate interests of confidentiality and of commercial secrets;
in calculating the appropriate administrative fine, the Commission shall be guided by the principles of effectiveness, proportionality and dissuasiveness, taking into consideration, where relevant, the seriousness and the effects of the infringement, the good faith of the economic operator, the degree of diligence and cooperation of the economic operator, the repetition, frequency or duration of the infringement as well as prior sanctions imposed on the same economic operator;
administrative fines shall be collected without undue delay by fixing deadlines for the payment and, as appropriate, including the possibility of splitting payments into several instalments and phases.
Article 86
Amendments to Regulation (EC) No 715/2007
Regulation (EC) No 715/2007 is amended as follows:
The title is replaced by the following:
‘Regulation (EC) No 715/2007 of the European Parliament and of the Council of 20 June 2007 on type approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6)’;
in Article 1, paragraph 2 is replaced by the following:
in Article 3, points 14 and 15 are deleted;
Chapter III is deleted;
in Article 13(2), point (e) is deleted.
Article 87
Amendments to Regulation (EC) No 595/2009
Regulation (EC) No 595/2009 is amended as follows:
The title is replaced by the following:
‘Regulation (EC) No 595/2009 of the European Parliament and of the Council of 18 June 2009 on type-approval of motor vehicles and engines with respect to emissions from heavy duty vehicles (Euro VI) and amending Regulation (EC) No 715/2007 and Directive 2007/46/EC and repealing Directives 80/1269/EEC, 2005/55/EC and 2005/78/EC’;
in Article 1, second paragraph is replaced by the following:
‘This Regulation also lays down rules for in-service conformity of vehicles and engines, the durability of pollution control devices, vehicle on-board diagnostic (OBD) systems and the measurement of fuel consumption and CO2 emissions.’;
in Article 3, points 11 and 13 are deleted;
Article 6 is deleted;
in Article 11(2), point (e) is deleted.
Article 88
Repeal of Directive 2007/46/EC
Directive 2007/46/EC is repealed with effect from 1 September 2020.
References to Directive 2007/46/EC shall be construed as references to this Regulation and shall be read in accordance with the correlation table set out in point 3 of Annex XI to this Regulation.
Article 89
Transitional provisions
The designation of technical services already designated before 4 July 2018 shall be renewed by 5 July 2022 where those technical services comply with the relevant requirements set out in this Regulation.
The validity of the designation of technical services made before 4 July 2018 shall terminate by 5 July 2022.
Article 90
Reporting
Article 91
Entry into force and application
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
It shall apply from 1 September 2020.
However, from 5 July 2020, national authorities shall not refuse to grant EU type-approval or national type-approval for a new type of vehicle, or prohibit registration, placing on the market or entry into service of a new vehicle where the vehicle concerned complies with this Regulation, if a manufacturer so requests.
This Regulation shall be binding in its entirety and directly applicable in all Member States.
LIST OF ANNEXES
|
Annex I |
General definitions, criteria for vehicle categorisation, types of vehicle and types of bodywork |
|
Appendix 1: |
Procedure for checking whether a vehicle can be categorised as off-road vehicle |
|
Appendix 2: |
Digits used to supplement the codes to be used for various kinds of bodywork |
|
Annex II |
Requirements for the purpose of EU type-approval of vehicles, systems, components or separate technical units |
|
Part I |
Regulatory acts for EU type-approval of vehicles produced in unlimited series |
|
Appendix 1: |
Regulatory acts for EU type-approval of vehicles produced in small series pursuant to Article 41 |
|
Appendix 2: |
Requirements for EU individual vehicle approval pursuant to Article 44 |
|
Part II |
List of UN Regulations recognised as an alternative to the Directives or Regulations referred to in Part I |
|
Part III |
List of regulatory acts setting out the requirements for the purpose of EU type-approval of special purpose vehicles |
|
Appendix 1: |
Motor-caravans, ambulances and hearses |
|
Appendix 2: |
Armoured vehicles |
|
Appendix 3: |
Wheelchair accessible vehicles |
|
Appendix 4: |
Other special purpose vehicles (including special group, multi-equipment carrier and trailer caravans) |
|
Appendix 5: |
Mobile cranes |
|
Appendix 6: |
Exceptional load transport vehicles |
|
Annex III |
Procedures to be followed with respect to EU type-approval |
|
Appendix 1: |
Standards with which the technical services referred to in Article 68 have to comply |
|
Appendix 2: |
Procedure for the assessment of the technical services |
|
Annex IV |
Conformity of production procedures |
|
Annex V |
Small series and end-of-series limits |
|
Annex VI |
List of parts or equipment that may pose a serious risk to the correct functioning of systems that are essential for the safety of the vehicle or its environmental performance, their performance requirements of such parts and equipment, the appropriate test procedures and marking and packaging provisions |
|
Annex VII |
Regulatory acts for which a manufacturer may be designated as a technical service |
|
Appendix: |
Designation of an in-house technical service of a manufacturer as technical service and subcontracting |
|
Annex VIII |
Conditions for the use of virtual testing methods by a manufacturer or a technical service |
|
Appendix 1: |
General conditions for the use of virtual testing methods |
|
Appendix 2: |
Specific conditions for the use of virtual testing methods |
|
Appendix 3: |
Validation process |
|
Annex IX |
Procedures to be followed during multi-stage type-approval |
|
Appendix: |
Model of the manufacturer's additional plate |
|
Annex X |
Access to vehicle OBD information and vehicle repair and maintenance information |
|
Appendix 1: |
Manufacturer's certificate on access to vehicle OBD information and vehicle repair and maintenance information |
|
Appendix 2: |
Vehicle OBD information |
|
Annex XI |
Correlation table |
ANNEX I
GENERAL DEFINITIONS, CRITERIA FOR VEHICLE CATEGORISATION, TYPES OF VEHICLE AND TYPES OF BODYWORK
INTRODUCTORY PART
Definitions and general provisions
1. Definitions
|
1.1. |
‘Seating position’ means any location capable of accommodating one person seated who is at least as large as:
(a)
the manikin of the 50th percentile adult male in the case of the driver;
(b)
the manikin of the 5th percentile adult female in all other cases. |
|
1.2. |
‘Seat’ means a complete structure with trim, integral or not with the vehicle body structure, which is intended to seat one person. It includes both an individual seat and a bench seat, as well as folding seats and removable seats. |
|
1.3. |
‘Goods’ means primarily any movable things. It includes products in bulk, manufactured goods, liquids, living animals, crops, indivisible loads. |
|
1.4. |
‘Maximum mass’ means the ‘technically permissible maximum laden mass’. |
2. General provisions
2.1. Number of seating positions
|
2.1.1. |
The requirements regarding the number of seating positions apply to seats that are designed for use when the vehicle is travelling on the road. |
|
2.1.2. |
They do not apply to seats that are designed for use when the vehicle is stationary and which are clearly identified to users either by means of a pictogram or a sign with an appropriate text. |
|
2.1.3. |
The following requirements apply for the counting of the seating positions:
(a)
each individual seat shall be counted as one seating position;
(b)
in the case of a bench seat, any space having a width of at least 400 mm measured at the seat cushion level shall be counted as one seating position. This condition shall not prevent the manufacturer from using the general provisions referred to in point 1.1;
(c)
however, a space as referred to in point (b) shall not be counted as one seating position where:
(i)
the bench seat includes features that prevent the bottom of the manikin from sitting in a natural way - for example: the presence of a fixed console box, an unpadded area or an interior trim interrupting the nominal seating surface;
(ii)
the design of the floor pan located immediately in front of a presumed seating position (for example the presence of a tunnel) prevents the feet of the manikin from being positioned in a natural way. |
|
2.1.4. |
With respect to vehicles covered by UN Regulations No 66 and No 107, the dimension referred to in point 2.1.3(b) shall be aligned with the minimum space required for one person in relation to the various classes of vehicles. |
|
2.1.5. |
When seat anchors for a removable seat are present in a vehicle, the removable seat shall be counted in the determination of the number of the seating positions. |
|
2.1.6. |
An area intended for an occupied wheelchair shall be regarded as one seating position.
|
2.2. Maximum mass
|
2.2.1. |
In the case of a tractor unit for semi-trailer, the maximum mass to be considered for classifying the vehicle shall include the maximum mass of the semi-trailer borne by the fifth wheel coupling. |
|
2.2.2. |
In the case of a motor vehicle that can tow a centre-axle trailer or a rigid drawbar trailer, the maximum mass to be considered for classifying the motor vehicle shall include the maximum mass transferred to the towing vehicle by the coupling. |
|
2.2.3. |
In the case of a semi-trailer, a centre-axle trailer and a rigid drawbar trailer, the maximum mass to be considered for classifying the vehicle shall correspond to the maximum mass transmitted to the ground by the wheels of an axle or group of axles when coupled to the towing vehicle. |
|
2.2.4. |
In the case of a converter dolly, the maximum mass to be considered for classifying the vehicle shall include the maximum mass of the semi-trailer borne by the fifth wheel coupling. |
2.3. Special equipment
|
2.3.1. |
Vehicles fitted primarily with fixed equipment such as machinery or apparatus shall be regarded as N or O category. |
2.4. Units
|
2.4.1. |
Unless otherwise stated any unit of measurement and associated symbol shall conform to Council Directive 80/181/EEC ( 8 ). |
3. Categorisation into vehicle categories
|
3.1. |
The manufacturer is responsible for the categorisation of a type of vehicle into a specific category. For such purposes, all the relevant criteria described in this Annex shall be met. |
|
3.2. |
The approval authority may request from the manufacturer appropriate additional information with the aim of demonstrating that a type of vehicle needs to be categorised as special purpose vehicle in the special group (‘SG Code’). |
PART A
Criteria for vehicle categorisation
1. Vehicle categories
For the purposes of EU type-approval and national type-approval, as well as for EU individual vehicle approval and national individual vehicle approval, vehicles shall be categorised in accordance with the classification referred to in Article 4.
Approval can only be granted for the categories referred to in Article 4(1).
2. Vehicle subcategories
2.1. Off-road vehicles
‘Off-road vehicle (ORV)’ means a vehicle that belongs to category M or N, having specific technical features which permit its use off the normal roads.
For those categories of vehicles, the letter ‘G’ shall be added as suffix to the letter and numeral identifying the vehicle category.
The criteria for the subcategorisation of vehicles as ORV are specified in point 4 of this Part.
2.2. Special purpose vehicles (SPV)
|
2.2.1. |
For incomplete vehicles that are intended to fall into the SPV subcategory, the letter ‘S’ shall be added as suffix to the letter and numeral identifying the vehicle category. The various types of special purpose vehicles are defined and listed in point 5. |
2.3. Off road special purpose vehicle
|
2.3.1. |
‘Off road special purpose vehicle (ORV-SPV)’ means a vehicle that belongs either to category M or N having the specific technical features referred to in points 2.1 and 2.2. For those categories of vehicles, the letter ‘G’ shall be added as suffix to the letter and numeral identifying the vehicle category. Moreover, for incomplete vehicles that are intended to fall into the SPV subcategory, the letter ‘S’ shall be added as second suffix. |
3. Criteria for the categorisation of vehicles in category N
|
3.1. |
The categorisation of a type of vehicle in category N shall be based on the technical features of the vehicle as referred to in points 3.2 to 3.6. |
|
3.2. |
As a matter of principle, the compartment(s) where all the seating positions are located, shall be completely separated from the loading area. |
|
3.3. |
By way of derogation from the requirements of point 3.2, persons and goods may be transported in the same compartment under the condition that the loading area is provided with securing devices designed to protect persons transported against the displacement of the load during driving, including severe braking and cornering. |
|
3.4. |
Securing devices - lashing devices - intended for securing the load as required in point 3.3 as well as partitioning systems, intended for vehicles up to 7,5 tonnes shall be designed in accordance with the provisions of sections 3 and 4 of international standard ISO 27956:2009 ‘Road vehicles – Securing of cargo in delivery vans – Requirements and test methods’.
|
|
3.5. |
The number of seating positions excluding the driver's seating position shall not exceed:
(a)
6 in the case of N1 vehicles;
(b)
8 in the case of N2 or N3 vehicles. |
|
3.6. |
Vehicles shall show a goods-carrying capacity equal or higher than the person-carrying capacity expressed in kg.
|
|
3.7. |
The requirements referred to in points 3.2 to 3.6 shall be met for all variants and versions within the type of vehicle. |
|
3.8. |
Criteria for the categorisation of vehicles as N1.
|
4. Criteria for the sub-categorisation of vehicles as off-road vehicles
|
4.1. |
M1 or N1 vehicles shall be subcategorised as off-road vehicles if they satisfy at the same time the following conditions:
(a)
at least one front and at least one rear axle designed to be driven simultaneously irrespective of whether one powered axle can be disengaged;
(b)
at least one differential locking mechanism or a mechanism having similar effect is fitted;
(c)
they are able to climb at least a 25 % gradient as a solo vehicle;
(d)
they satisfy five out of the following six requirements:
(i)
the approach angle shall be at least 25 degrees;
(ii)
the departure angle shall be at least 20 degrees;
(iii)
the ramp angle shall be at least 20 degrees;
(iv)
the ground clearance under the front axle shall be at least 180 mm;
(v)
the ground clearance under the rear axle shall be at least 180 mm;
(vi)
the ground clearance between the axles shall be at least 200 mm. |
|
4.2. |
M2, N2 or M3 vehicles the maximum mass of which does not exceed 12 tonnes shall be subcategorised as off-road vehicles if they satisfy either the condition set out in point (a) or the conditions set out in both points (b) and (c):
(a)
all their axles are driven simultaneously, irrespective of whether one or more powered axles can be disengaged;
(b)
(i)
at least one front and at least one rear axle are designed to be driven simultaneously irrespective of whether one powered axle can be disengaged;
(ii)
at least one differential locking mechanism or a mechanism having the same effect is fitted;
(iii)
they are able to climb a 25 % gradient as a solo vehicle;
(c)
they satisfy at least five out of the following six requirements if their maximum mass does not exceed 7,5 tonnes and at least four if their maximum mass exceeds 7,5 tonnes:
(i)
the approach angle shall be at least 25 degrees;
(ii)
the departure angle shall be at least 25 degrees;
(iii)
the ramp angle shall be at least 25 degrees;
(iv)
the ground clearance under the front axle shall be at least 250 mm;
(v)
the ground clearance between axles shall be at least 300 mm;
(vi)
the ground clearance under the rear axle shall be at least 250 mm. |
|
4.3. |
M3 or N3 vehicles whose maximum mass exceeds 12 tonnes shall be subcategorised as off-road vehicles if they satisfy either the condition set out in point (a) or the conditions set out in both points (b) and (c):
(a)
all their axles are driven simultaneously, irrespective of whether one or more powered axles can be disengaged;
(b)
(i)
at least half of the axles (or two axles out of the three in the case of a three axle vehicle and three axles in the case of a five axle vehicle) is designed to be driven simultaneously, irrespective of whether one powered axle can be disengaged;
(ii)
there is at least one differential locking mechanism or a mechanism having similar effect;
(iii)
they are able to climb a 25 % gradient as solo vehicle;
(c)
they satisfy at least four out of the following six requirements:
(i)
the approach angle shall be at least 25 degrees;
(ii)
the departure angle shall be at least 25 degrees;
(iii)
the ramp angle shall be at least 25 degrees;
(iv)
the ground clearance under the front axle shall be at least 250 mm;
(v)
the ground clearance between axles shall be at least 300 mm;
(vi)
the ground clearance under the rear axle shall be at least 250 mm. |
|
4.4. |
The procedure for checking compliance with the geometrical provisions referred to in this Part shall be set out in Appendix 1. |
|
4.5. |
The requirements in points 4.1(a), 4.2(a), 4.2(b), 4.3(a), 4.3(b) on simultaneous driven axles are considered to have been fulfilled if one of the following conditions is fulfilled:
(a)
the transmission of the tractive power to all axles is performed by mechanical means only which provides traction in heavy off-road; or
(b)
each of the wheels of the axle in question is driven by an individual hydraulic or electric motor. If the axles according to the requirements in points 4.1(a), 4.2(a), 4.2(b), 4.3(a), 4.3(b) on simultaneous driven axles are not powered by mechanical means only, the propulsion of the individual wheels shall be designed for heavy off-road operation. In such case it shall be ensured that at least 75 % of total tractive power can be transmitted to the wheel in question when the tractive conditions under the other wheels do not allow to transmit the tractive power properly via these wheels. The auxiliary drive system according to point 4.5(b) shall not allow to disengage the tractive power automatically until the vehicle reaches 75 % of the maximum vehicle design speed or reaches 65 km/h. |
5. Special purpose vehicles
|
|
Name |
Code |
Definition |
|
5.1. |
Motor caravan |
SA |
A vehicle of category M with living accommodation space which contains the following equipment as a minimum: (a) seats and table; (b) sleeping accommodation which may be converted from the seats; (c) cooking facilities; (d) storage facilities. This equipment shall be rigidly fixed to the living compartment. However, the table may be designed to be easily removable. |
|
5.2. |
Armoured vehicle |
SB |
A vehicle intended for the protection of conveyed persons or goods with anti-bullet armour plating. |
|
5.3. |
Ambulance |
SC |
A vehicle of category M intended for the transport of sick or injured persons and having special equipment for such purpose. |
|
5.4. |
Hearse |
SD |
A vehicle of category M intended for the transport of deceased persons and having special equipment for such purpose. |
|
5.5. |
Wheelchair accessible vehicle |
SH |
A vehicle of category M1 constructed or converted specifically so that they accommodate one or more persons seated in their wheelchairs when travelling on the road. |
|
5.6. |
Trailer caravan |
SE |
A vehicle of category O as defined in term 3.2.1.3 of international standard ISO 3833:1977. |
|
5.7. |
Mobile crane |
SF |
A vehicle of category N3, not fitted for the carriage of goods, provided with a crane whose lifting moment is equal to or higher than 400 kNm. |
|
5.8. |
Special group |
SG |
A special purpose vehicle that does not enter in any of the definitions mentioned in this Part. |
|
5.9. |
Converter dolly |
SJ |
A vehicle of category O equipped with a fifth-wheel coupling to support a semi-trailer with a view to converting the latter into a trailer. |
|
5.10. |
Exceptional load transport trailer |
SK |
A vehicle of category O4 intended for the transport of indivisible loads that is subject to speed and traffic restrictions because of its dimensions. Under this term are also included hydraulic modular trailers irrespective of the number of modules. |
|
5.11. |
Exceptional load transport motor vehicle |
SL |
A road tractor or tractor unit for semi-trailer of category N3 meeting all the following conditions: (a) having more than two axles and at least half of the axles (two axles out of three in the case of a three axle vehicle and three axles out of five in the case of a five axle vehicle) designed to be driven simultaneously, irrespective of whether one powered axle can be disengaged; (b) that is designed for towing and pushing exceptional load transport trailer of category O4; (c) that has a minimum engine power of 350 kW; and (d) that can be equipped with an additional front coupling device for heavy towable masses. |
|
5.12. |
Multi-equipment carrier |
SM |
An off-road vehicle of category N (as defined in point 2.3) designed and constructed for pulling, pushing, carrying and actuating certain inter-changeable equipment: (a) with not less than two mounting areas for this equipment; (b) with standardised, mechanical, hydraulic and/or electrical interfaces (e.g. Power take off) for powering and actuating the inter-changeable equipment; and (c) that fulfils the definition of international standard ISO 3833-1977, paragraph 3.1.4 (special vehicle). If the vehicle is equipped with an auxiliary load platform, its maximum length shall not exceed: (a) 1,4 times of the front or rear track width of the vehicle, whichever is the larger in the case of two axle vehicles; or (b) 2,0 times of the front or rear track width of the vehicle, whichever is the larger in the case of vehicles having more than two axles. |
6. Remarks
|
6.1. |
Type-approval shall not be granted:
(a)
to converter dolly as defined in point 5.9 of this Part;
(b)
to rigid drawbar trailers as defined in point 5.4 of Part C;
(c)
to trailers in which persons may be carried when travelling on the road. |
|
6.2. |
Point 6.1 is without prejudice to Article 42 on national small series type-approval. |
PART B
Criteria for types of vehicle, variants and versions
1. Category M1
1.1. Type of vehicle
|
1.1.1. |
A ‘type of vehicle’ shall consist of vehicles that have the following features in common:
(a)
the manufacturer's company name. A change in the legal form of ownership of the company does not require that a new approval has to be granted;
(b)
the design and assembly of the essential parts of the body structure in the case of a self-supporting body. The same shall apply to vehicles the bodywork of which is bolted on or welded to a separate frame; |
|
1.1.2. |
By way of derogation from the requirements of point 1.1.1(b), when the manufacturer uses the floor portion of the body structure as well as the essential constituent elements forming the front part of the body structure located directly in front of the windscreen bay, in the construction of different kinds of bodywork (for example a saloon and a coupe), those vehicles may be considered as belonging to the same type. Evidence thereof shall be provided by the manufacturer. |
|
1.1.3. |
A type shall consist of at least one variant and one version. |
1.2. Variant
|
1.2.1. |
A ‘variant’ within a type of vehicle shall group the vehicles that have the following construction features in common:
(a)
the number of lateral doors or the type of bodywork as defined in point 2 of Part C when the manufacturer uses the criterion of point 1.1.2;
(b)
the power plant with regard to the following construction features:
(i)
the type of energy supply (internal combustion engine, electric motor or other);
(ii)
the working principle (positive ignition, compression ignition or other);
(iii)
the number and arrangement of cylinders in the case of internal combustion engine (L4, V6 or other);
(c)
the number of axles;
(d)
the number, and interconnection of powered axles;
(e)
the number of steered axles;
(f)
the stage of completion (e.g. complete/incomplete);
(g)
in the case of multi-stage built vehicles, the manufacturer and the type of the previous stage vehicle. |
1.3. Version
|
1.3.1. |
A ‘version’ within a variant shall group the vehicles that have the following features in common:
(a)
the technically permissible maximum laden mass;
(b)
the engine capacity in the case of internal combustion engine;
(c)
the maximum engine power output or the maximum continuous rated power (electric motor);
(d)
the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(e)
the maximum number of seating positions;
(f)
drive-by sound level;
(g)
exhaust emission level (for example Euro 5, Euro 6 or other);
(h)
combined or weighted, combined CO2 emissions;
(i)
electric energy consumption (weighted, combined);
(j)
combined or weighted, combined fuel consumption; As an alternative to the criteria in points (h), (i) and (j), the vehicles grouped into a version shall have in common all tests performed for the calculation of their CO2 emissions, electric energy consumption and fuel consumption in accordance with sub-Annex 6 to Annex XXI to Commission Regulation (EU) 2017/1151 ( 9 ). |
2. Categories M2 and M3
2.1. Type of vehicle
|
2.1.1. |
A ‘type of vehicle’ shall consist of vehicles that have the following features in common:
(a)
the manufacturer's company name. A change in the legal form of ownership of the company does not require that a new approval has to be granted;
(b)
the category;
(c)
the following aspects of construction and design:
(i)
the design and construction of the essential constituent elements forming the chassis;
(ii)
the design and construction of the essential constituent elements forming the body structure in the case of a self-supporting body;
(d)
the number of decks (single or double);
(e)
the number of sections (rigid/articulated);
(f)
the number of axles;
(g)
the mode of energy supply (on-board or off-board); |
|
2.1.2. |
A type of vehicle shall consist of at least one variant and one version. |
2.2. Variant
|
2.2.1. |
A ‘variant’ within a type of vehicle shall group the vehicles that have all of the following construction features in common:
(a)
the type of bodywork as defined in point 3 of Part C;
(b)
the class or combination of classes of vehicles as defined in paragraph 2.1.1 of UN Regulation No 107 (only in the case of complete and completed vehicles);
(c)
the stage of completion (e.g. complete/incomplete/completed);
(d)
the power plant with regard to the following construction features:
(i)
the type of energy supply (internal combustion engine, electric motor or other);
(ii)
the working principle (positive ignition, compression ignition or other);
(iii)
the number and arrangement of cylinders in the case of internal combustion engine (L6, V8 or other);
(e)
in the case of multi-stage built vehicles, the manufacturer and the type of the previous stage vehicle. |
2.3. Version
|
2.3.1. |
A ‘version’ within a variant shall group the vehicles that have all the following features in common:
(a)
the technically permissible maximum laden mass;
(b)
the ability of the vehicle to tow a trailer or not;
(c)
the engine capacity in the case of internal combustion engine;
(d)
the maximum engine power output or the maximum continuous rated power (electric motor);
(e)
the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(f)
drive-by sound level;
(g)
exhaust emission level (for example Euro IV, Euro V or other). |
3. Category N1
3.1. Type of vehicle
|
3.1.1. |
A ‘type of vehicle’ shall consist of vehicles that have the following features in common:
(a)
the manufacturer's company name. A change in the legal form of ownership of the company does not require that a new approval has to be granted;
(b)
the design and assembly of the essential parts of the body structure in the case of a self-supporting body;
(c)
the design and the construction of the essential constituent elements forming the chassis in the case of a non-self-supporting body. |
|
3.1.2. |
By way of derogation from the requirements of point 3.1.1(b), when the manufacturer uses the floor portion of the body structure as well the essential constituent elements forming the front part of the body structure located directly in front of the windscreen bay, in the construction of different kinds of bodywork (for example a van and a chassis-cab, different wheelbases and different roof heights), those vehicles may be considered as belonging to the same type. Evidence thereof shall be provided by the manufacturer. |
|
3.1.3. |
A type of vehicle shall consist of at least one variant and one version. |
3.2. Variant
|
3.2.1. |
A ‘variant’ within a type of vehicle shall group the vehicles that have the following construction features in common:
(a)
the number of lateral doors or the type of bodywork as defined in point 4 of Part C (for complete and completed vehicles) when the manufacturer uses the criterion of point 3.1.2;
(b)
the stage of completion (e.g. complete/incomplete/completed);
(c)
the power plant with regard to the following construction features:
(i)
the type of energy supply (internal combustion engine, electric motor or other);
(ii)
the working principle (positive ignition, compression ignition or other);
(iii)
the number and arrangement of cylinders in the case of internal combustion engine (L6, V8 or other);
(d)
the number of axles;
(e)
the number and interconnection of powered axles;
(f)
the number of steered axles.
(g)
in the case of multi-stage built vehicles, the manufacturer and the type of the previous stage vehicle. |
3.3. Version
|
3.3.1. |
A ‘version’ within a variant shall group the vehicles that have the following features in common:
(a)
the technically permissible maximum laden mass;
(b)
the engine capacity in the case of internal combustion engine;
(c)
the maximum engine power output or maximum continuous rated power (electric motor);
(d)
the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(e)
the maximum number of seating positions;
(f)
drive-by sound level;
(g)
exhaust emission level (for example Euro 5, Euro 6 or other);
(h)
combined or weighted, combined CO2 emissions;
(i)
electric energy consumption (weighted, combined);
(j)
combined or weighted, combined fuel consumption;
(k)
the existence of a unique set of innovative technologies, as specified in Article 12 of Regulation (EU) No 510/2011 of the European Parliament and of the Council ( 10 ). As an alternative to the criteria in points (h), (i) and (j), the vehicles grouped into a version shall have in common all tests performed for the calculation of their CO2 emissions, electric energy consumption and fuel consumption in accordance with sub-Annex 6 to Annex XXI of Regulation (EU) 2017/1151. |
4. Categories N2 and N3
4.1. Type of vehicle
|
4.1.1. |
A ‘type of vehicle’ shall consist of vehicles that have the following features in common:
(a)
the manufacturer's company name. A change in the legal form of ownership of the company does not require that a new approval has to be granted;
(b)
the category;
(c)
the design and construction of the chassis that are common to a single line of product;
(d)
the number of axles; |
|
4.1.2. |
A type of vehicle shall consist of at least one variant and one version. |
4.2. Variant
|
4.2.1. |
A ‘variant’ within a type of vehicle shall group the vehicles that have the following construction features in common:
(a)
the body structural concept or type of bodywork as defined in point 4 of Part C and in Appendix 2 (only for complete and completed vehicles);
(b)
the stage of completion (e.g. complete/incomplete/completed);
(c)
the power plant with regard to the following construction features:
(i)
the type of energy supply (internal combustion engine, electric motor or other);
(ii)
the working principle (positive ignition, compression ignition or other);
(iii)
the number and arrangement of cylinders in the case of internal combustion engine (L6, V8 or other);
(d)
the number and interconnection of powered axles;
(e)
the number of steered axles;
(f)
in the case of multi-stage built vehicles, the manufacturer and the type of the previous stage vehicle. |
4.3. Version
|
4.3.1. |
A ‘version’ within a variant shall group the vehicles that have the following features in common:
(a)
the technically permissible maximum laden mass;
(b)
the ability or not to tow a trailer as follows:
(i)
an unbraked trailer;
(ii)
a trailer with an inertia (or overrun) braking system as defined in paragraph 2.12 of UN Regulation No 13;
(iii)
a trailer with a continuous or semi-continuous braking system as defined in paragraphs 2.9 and 2.10 of UN Regulation No 13;
(iv)
a trailer of category O4 that results in a maximum mass of the combination not exceeding 44 tonnes;
(v)
a trailer of category O4 that results in a maximum mass of the combination exceeding 44 tonnes;
(c)
the engine capacity;
(d)
the maximum engine power output;
(e)
the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(f)
drive-by sound level;
(g)
exhaust emission level (for example Euro IV, Euro V or other). |
5. Categories O1 and O2
5.1. Type of vehicle
|
5.1.1. |
A ‘type of vehicle’ shall consist of vehicles that have the following features in common:
(a)
the manufacturer's company name. A change in the legal form of ownership of the company does not require that a new approval has to be granted;
(b)
the category;
(c)
the concept as defined in point 5 of Part C;
(d)
the following aspects of construction and design:
(i)
the design and construction of the essential constituent elements forming the chassis;
(ii)
the design and construction of the essential constituent elements forming the body structure in the case of a self-supporting body;
(e)
the number of axles. |
|
5.1.2. |
A type of vehicle shall consist of at least one variant and one version. |
5.2. Variant
|
5.2.1. |
A ‘variant’ within a type of vehicle shall group the vehicles that have the following construction features in common:
(a)
the kind of bodywork as referred to in Appendix 2 (for complete and completed vehicles);
(b)
the stage of completion (e.g. complete/incomplete/completed);
(c)
the type of braking system (e.g. unbraked/inertia/power);
(d)
in the case of multi-stage built vehicles, the manufacturer and the type of the previous stage vehicle. |
5.3. Version
|
5.3.1. |
A ‘version’ within a variant shall group the vehicles that have the following features in common:
(a)
the technically permissible maximum laden mass;
(b)
the concept of the suspension (air, steel or rubber suspension, torsion bar or other);
(c)
the concept of the drawbar (triangle, tube or other). |
6. Categories O3 and O4
6.1. Type of vehicle
|
6.1.1. |
A ‘type of vehicle’ shall consist of vehicles that have the following features in common:
(a)
the manufacturer's company name. A change in the legal form of ownership of the company does not require that a new approval has to be granted;
(b)
the category;
(c)
the concept of the trailer with relation to the definitions in point 5 of Part C;
(d)
the following aspects of construction and design:
(i)
the design and construction of the essential constituent elements forming the chassis;
(ii)
the design and construction of the essential constituent elements forming the body structure in the case of trailers with a self-supporting body;
(e)
the number of axles. |
|
6.1.2. |
A type of vehicle shall consist of at least one variant and one version. |
6.2. Variants
|
6.2.1. |
A ‘variant’ within a type of vehicle shall group the vehicles that have the following construction and design features in common:
(a)
the kind of bodywork as referred to in Appendix 2 (for complete and completed vehicles);
(b)
the stage of completion (e.g. complete/incomplete/completed);
(c)
the concept of the suspensions (steel, air or hydraulic suspension);
(d)
the following technical features:
(i)
the capability or not for the chassis to be extendible;
(ii)
the deck height (normal, low loader, semi-low loader etc.);
(e)
in the case of multi-stage built vehicles, the manufacturer and the type of the previous stage vehicle. |
6.3. Versions
|
6.3.1. |
A ‘version’ within a variant shall group the vehicles that have the following features in common:
(a)
the technically permissible maximum laden mass;
(b)
the subdivisions or combination of subdivisions referred to in points 3.2 and 3.3 of Annex I to Directive 96/53/EC into which the axle spacing between two consecutive axles forming a group belongs;
(c)
the definition of the axles in the following respects:
(i)
lift axles (number and position);
(ii)
loadable axles (number and position);
(iii)
steered axle (number and position). |
7. Common requirements for all vehicle categories
|
7.1. |
When a vehicle falls into several categories because of its maximum mass or the number of seating positions or both, the manufacturer may select to use the criteria of one or the other vehicle category for the definition of the variants and the versions.
|
|
7.2. |
A vehicle of category N may be type-approved against the provisions required for category M1 or M2, as the case may be, when it is intended to be converted into a vehicle of that category during the next step of a multi-stage type-approval procedure.
|
|
7.3. |
Type-, variant- and version designations
|
|
7.4. |
Number of characters for the TVV
|
PART C
Definitions of types of bodywork
1. General
|
1.1. |
The type of bodywork as well as the code for bodywork shall be indicated by means of codes. The list of codes shall apply primarily to complete and completed vehicles. |
|
1.2. |
As regards vehicles of categories M, the type of bodywork shall consist of two letters as specified in points 2 and 3. |
|
1.3. |
As regards vehicles of categories N and O, the type of bodywork shall consist of two letters as referred to in points 4 and 5. |
|
1.4. |
Where necessary (especially for the types of bodywork referred to respectively in points 4.1 and 4.6 and in points 5.1 to 5.4), they shall be supplemented by two digits.
|
|
1.5. |
For special purpose vehicles, the type of bodywork to be used shall be linked to the category of the vehicle. |
2. Vehicles belonging to category M1
|
Ref. |
Code |
Name |
Definition |
|
2.1. |
AA |
Saloon |
A vehicle defined in term 3.1.1.1 of international standard ISO 3833:1977, fitted with at least four side windows. |
|
2.2. |
AB |
Hatchback |
A saloon as defined in 2.1 with a hatch at the rear end of the vehicle. |
|
2.3. |
AC |
Station wagon |
A vehicle defined in term 3.1.1.4 of international standard ISO 3833:1977. |
|
2.4. |
AD |
Coupé |
A vehicle defined in term 3.1.1.5 of international standard ISO 3833:1977. |
|
2.5. |
AE |
Convertible |
A vehicle defined in terms No 3.1.1.6 of international standard ISO 3833:1977. However, a convertible may have no door. |
|
2.6. |
AF |
Multi-purpose vehicle |
A vehicle other than AG and those mentioned in AA to AE intended for carrying persons and their luggage or occasionally goods, in a single compartment. |
|
2.7. |
AG |
Truck station wagon |
A vehicle defined in term No 3.1.1.4.1 of international standard ISO 3833:1977. However, the luggage compartment must be completely separated from the passenger compartment. In addition, the reference point of the driver's seating position needs not to be at least at 750 mm above the surface supporting the vehicle. |
3. Vehicles belonging to category M2 or M3
|
Ref. |
Code |
Name |
Definition |
|
3.1. |
CA |
Single-deck vehicle |
A vehicle where the spaces provided for persons are arranged in a single level or in a way that they do not constitute two superimposed levels; |
|
3.2. |
CB |
Double-deck vehicle |
A vehicle defined in paragraph 2.1.6 of UN Regulation No 107; |
|
3.3. |
CC |
Single-deck articulated vehicle |
A vehicle defined in paragraph 2.1.3 of UN Regulation No 107 with a single deck; |
|
3.4. |
CD |
Double-deck articulated vehicle |
A vehicle defined in paragraph 2.1.3.1 of UN Regulation No 107; |
|
3.5. |
CE |
Low-floor single-deck vehicle |
A vehicle defined in paragraph 2.1.4 of UN Regulation No 107 with a single deck; |
|
3.6. |
CF |
Low-floor double-deck vehicle |
A vehicle defined in paragraph 2.1.4 of UN Regulation No 107 with a double deck; |
|
3.7. |
CG |
Articulated low-floor single-deck vehicle |
A vehicle that combines the technical features of points 3.3 and 3.5 of this table; |
|
3.8. |
CH |
Articulated low-floor double-deck vehicle |
A vehicle that combines the technical features of points 3.4 and 3.6 of this table; |
|
3.9. |
CI |
Open top single deck vehicle |
A vehicle with partial roof or without roof; |
|
3.10. |
CJ |
Open top double deck vehicle |
A vehicle without roof over all or part of its upper deck; |
|
3.11. |
CX |
Bus chassis |
An incomplete vehicle with just chassis rails or tube assembly, power train, axles, that is intended to be completed with bodywork, customised to the needs of the transport operator. |
4. Motor vehicles of category N1, N2 or N3
|
Ref. |
Code |
Name |
Definition |
|
4.1. |
BA |
Lorry |
A vehicle that is designed and constructed exclusively or principally for conveying goods. It may also tow a trailer. |
|
4.2. |
BB |
Van |
A lorry with the compartment where the driver is located and cargo area within a single unit. |
|
4.3. |
BC |
Tractor unit for semi-trailer |
A towing vehicle that is designed and constructed exclusively or principally to tow semi-trailers. |
|
4.4. |
BD |
Road tractor |
A towing vehicle that is designed and constructed exclusively to tow trailers other than semi-trailers. |
|
4.5. |
BE |
Pick-up truck |
A vehicle of a maximum mass not exceeding 3 500 kg in which the seating positions and the cargo area are not located in a single compartment. |
|
4.6. |
BX |
Chassis-cab or chassis-cowl |
An incomplete vehicle with just a cabin (complete or partial), chassis rails, power train, axles, which is intended to be completed with bodywork, customised to the needs of the transport operator. |
5. Vehicles of category O
|
Ref. |
Code |
Name |
Definition |
|
5.1. |
DA |
Semi-trailer |
A trailer that is designed and constructed to be coupled to a tractor unit or to a converter dolly and to impose a substantial vertical load on the towing vehicle or on the converter dolly. The coupling to be used for a vehicle combination shall consist of a king pin and a fifth wheel. |
|
5.2. |
DB |
Drawbar trailer |
A trailer having at least two axles, of which at least one is a steered axle: (a) equipped with a towing device which can move vertically (in relation to the trailer); and (b) that transmits less than 100 daN as a static vertical load to the towing vehicle. |
|
5.3. |
DC |
Centre-axle trailer |
A trailer where the axle(s) is (are) positioned close to the centre of gravity of the vehicle (when uniformly loaded) so that only a small static vertical load, not exceeding 10 % of that corresponding to the maximum mass of the trailer or a load of 1 000 daN (whichever is the lesser) is transmitted to the towing vehicle. |
|
5.4. |
DE |
Rigid drawbar trailer |
A trailer with one axle or one group of axles fitted with a drawbar which transmits a static load not exceeding 4 000 daN to the towing vehicle due to its construction and that does not meet the definition of a centre-axle trailer. The coupling to be used for a vehicle combination shall not consist of a king pin and a fifth wheel. |
|
5.5. |
DF |
Link semi-trailer |
A semi-trailer with a fifth wheel mounted at the rear such that the link semi-trailer could tow another semi-trailer. |
|
5.6. |
DG |
Link drawbar trailer |
A drawbar trailer with a fifth wheel mounted at the rear such that the link trailer could tow another semi-trailer. |
Appendix 1
Procedure for checking whether a vehicle can be categorised as off-road vehicle
1. General
|
1.1. |
For the purposes of classification of a vehicle as off-road vehicle, the procedure described in this Appendix shall apply. |
2. Test conditions for geometric measurements
|
2.1. |
Vehicles belonging to category M1 or N1 shall be in unloaded conditions with a manikin of the 50th percentile male installed on the driver's seat and fitted with coolant fluid, lubricants, fuel, tools, spare-wheel (if fitted as OEM equipment). The manikin may be replaced by a similar device having the same mass. |
|
2.2. |
Vehicles other than those referred to in point 2.1 shall be loaded to their technically permissible maximum laden mass. The distribution of the mass on the axles shall be the one that represents the worst case with respect to compliance with the respective criteria. |
|
2.3. |
A vehicle representative of the type shall be submitted to the technical service in the conditions specified in point 2.1 or 2.2. The vehicle shall be in a stationary position with its wheels set straight ahead. The ground on which measurements are made shall be as flat and horizontal (maximum of inclination 0,5 %) as possible. |
3. Measurement of approach, departure and ramp angles
|
3.1. |
The approach angle shall be measured in accordance with paragraph 6.10 of international standard ISO 612:1978. |
|
3.2. |
The departure angle shall be measured in accordance with paragraph 6.11 of international standard ISO 612:1978. |
|
3.3. |
The ramp angle shall be measured in accordance with paragraph 6.9 of international standard ISO 612:1978. |
|
3.4. |
When measuring the departure angle rear underrun protection devices which are adjustable in height may be set in the upper position. |
|
3.5. |
The prescription in point 3.4 shall not be construed as an obligation for the base vehicle to be fitted with a rear underrun protection as original equipment. However, the base vehicle manufacturer shall inform the next stage manufacturer that the vehicle has to comply with the requirements on departure angle when fitted with a rear underrun protection. |
4. Measurement of ground clearance
4.1. Ground clearance between the axles
|
4.1.1. |
‘Ground clearance between the axles’ means the shortest distance between the ground plane and the lowest fixed point of the vehicle. For the application of the definition, the distance between the last axle of a front group of axle and the first axle of a rear group of axle shall be considered.
|
|
4.1.2. |
No rigid part of the vehicle may project into the shaded area shown on the figure. |
4.2. Ground clearance beneath one axle
|
4.2.1. |
‘Ground clearance beneath one axle’ means the distance beneath the highest point of the arc of a circle passing through the centre of the tyre footprint of the wheels on one axle (the inner wheels in the case of twin tyres) and touching the lowest fixed point of the vehicle between the wheels.
|
|
4.2.2. |
Where appropriate, the measurement of ground clearance shall be conducted on each of the several axles of a group of axles. |
5. Gradeability
|
5.1. |
‘Gradeability’ means the ability of a vehicle to negotiate a gradient. |
|
5.2. |
To the effect of checking the gradeability of an incomplete and a complete vehicle of category M2, M3, N2 and N3, a test shall be performed. |
|
5.3. |
The test shall be conducted by the technical service on a vehicle representative of the type to be tested. |
|
5.4. |
At the request of the manufacturer and under the conditions specified in Annex VIII, the gradeability of a type of vehicle may be demonstrated by virtual testing. |
6. Test conditions and pass-fail criterion
|
6.1. |
The conditions set out in Annex II to Commission Regulation (EU) No 1230/2012 ( 11 ) shall apply. |
|
6.2. |
The vehicle shall climb the gradient at a steady speed without any wheel slipping, longitudinally or laterally. |
Appendix 2
Digits used to supplement the codes to be used for various kinds of bodywork
|
01 |
Flat bed; |
|
02 |
Drop-side; |
|
03 |
Box body; |
|
04 |
Conditioned body with insulated walls and equipment to maintain the interior temperature; |
|
05 |
Conditioned body with insulated walls but without equipment to maintain the interior temperature; |
|
06 |
Curtain-sided; |
|
07 |
Swap body (interchangeable superstructure); |
|
08 |
Container carrier; |
|
09 |
Vehicles fitted with hook lift; |
|
10 |
Tipper; |
|
11 |
Tank; |
|
12 |
Tank intended for transport of dangerous goods; |
|
13 |
Livestock carrier; |
|
14 |
Vehicle transporter; |
|
15 |
Concrete mixer; |
|
16 |
Concrete pump vehicle; |
|
17 |
Timber; |
|
18 |
Refuse collection vehicle; |
|
19 |
Street sweeper, cleansing and drain clearing; |
|
20 |
Compressor; |
|
21 |
Boat carrier; |
|
22 |
Glider carrier; |
|
23 |
Vehicles for retail or display purposes; |
|
24 |
Recovery vehicle; |
|
25 |
Ladder vehicle; |
|
26 |
Crane lorry (other than a mobile crane as defined in point 5.7 of Part A); |
|
27 |
Aerial work platform vehicle; |
|
28 |
Digger derrick vehicle; |
|
29 |
Low floor trailer; |
|
30 |
Glazing transporter; |
|
31 |
Fire engine; |
|
32 |
Drop-side tarpaulin; |
|
99 |
Bodywork that is not included in this list. |
ANNEX II
REQUIREMENTS FOR THE PURPOSE OF EU TYPE-APPROVAL OF VEHICLES, SYSTEMS, COMPONENTS OR SEPARATE TECHNICAL UNITS
PART I
Regulatory acts for EU type-approval of vehicles produced in unlimited series
EXPLANATORY NOTES
to the table for vehicles produced in unlimited series
|
X |
: |
Applies to the vehicle category, separate technical unit or component in accordance with the regulatory act as indicated |
|
IF |
: |
Applies only if the system, separate technical unit or component is fitted to the vehicle in the respective vehicle category |
|
Item |
Subject |
Regulatory act |
M1 |
M2 |
M3 |
N1 |
N2 |
N3 |
O1 |
O2 |
O3 |
O4 |
STU |
Component |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
|||||||||||||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
X |
|
|
|
|
|
|
|
|
|
|
|
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
|
X |
X |
|
|
|
|
|
|
|
|
X |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
X |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
X |
|
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
X |
IF X |
IF X |
IF X |
IF X |
IF X |
|
|
|
|
|
|
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
X |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
X |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
|
|
|
|
X |
X |
|
|
|
|
X |
X |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
|
|
|
|
X |
X |
|
|
X |
X |
|
|
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
X |
|
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
X |
|
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
|
|
|
X |
X |
X |
|
|
|
|
|
|
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
X |
|
|
X |
|
|
|
|
|
|
X |
X |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
|||||||||||||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
X |
|
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
X |
|
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
X |
|
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
|
|
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
X |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
|||||||||||||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
|
|
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
X |
|
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
|
|
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
C13 |
Tyre pressure monitoring for light–duty vehicles |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
X |
X |
|
|
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
|||||||||||||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
X |
IF X |
IF X |
X |
IF X |
IF X |
|
|
|
|
X |
X |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
X |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
|
X |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
|
|
|
|
|
|
|
|
|
|
|
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
X |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
X |
|
|
|
|
|
|
|
|
|
|
|
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
|||||||||||||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
|
X |
X |
|
X |
X |
|
|
|
|
|
|
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
|||||||||||||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
X |
|
|
X |
X |
X |
|
|
|
|
|
|
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
X |
|
|
|
|
|
|
|
|
|
|
|
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
|
|
|
X |
X |
X |
|
|
|
|
|
|
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
X |
|
|
|
|
|
|
|
|
|
|
|
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
|
|
|
X |
X |
X |
X |
X |
X |
X |
X |
|
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
IF X |
IF X |
IF X |
IF X |
IF X |
X |
X |
X |
X |
X |
X |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
|
|
|
X |
X |
X |
X |
X |
X |
X |
|
|
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
|
X |
X |
|
|
|
|
|
|
|
|
|
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
|
X |
X |
|
|
|
|
|
|
|
|
|
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
|
|
X |
|
|
|
|
|
|
|
|
X |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
|||||||||||||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
X |
X |
|
X |
X |
|
|
|
|
|
|
X |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
X |
X |
|
X |
X |
|
|
|
|
|
|
X |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
|
|
X |
|
X |
X |
|
|
|
|
|
|
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
|
|
|
|
|
|
|
|
X |
X |
|
|
|
G4 |
Tailpipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
X |
X |
|
X |
X |
|
|
|
|
|
|
|
|
G8 |
Low-temperature tailpipe emissions in lab |
Regulation (EC) No 715/2007 |
X |
X |
|
X |
X |
|
|
|
|
|
|
|
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
X |
|
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
|
|
|
|
|
|
|
G13 |
Recyclability |
Directive 2005/64/EC |
X |
|
|
X |
|
|
|
|
|
|
|
|
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
X |
|
|
X |
|
|
|
|
|
|
|
X |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
|||||||||||||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X. |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
|
H2 |
Software update |
Regulation (EU) 2018/858, Annex IV UN Regulation No 156 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
The item and subject entries listed in the table above shall apply for the purpose of information to be provided in accordance with Commission Implementing Regulation (EU) 2020/683, Annex II, Part III from 6 December 2022 for new whole-vehicle type-approvals and from 6 December 2024 for existing approvals.
Compliance with Regulation (EU) 2019/2144 is mandatory, however, a separate type-approval under that Regulation is not foreseen as it represents the collection of individual items.
Compliance with items from G2 to G12 is mandatory, however, only one type-approval either under Regulation (EC) No 715/2007 or under Regulation (EC) No 595/2009 is foreseen depending on the scope.
Appendix 1
EXPLANATORY NOTES
to the tables for vehicles produced in small series
The requirements laid down in Table 1 for ‘Small series scheme I’ apply provided that:
In all other cases, the requirements laid down in Table 1 for ‘Small series scheme II’ and in Table 2 apply.
|
X |
: |
Full application of the regulatory act as follows:
(a)
a type-approval certificate shall be required;
(b)
tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 67 to 81;
(c)
the test report shall be drafted in accordance with Annex III;
(d)
Conformity of Production shall be ensured. |
|
A |
: |
Application of the regulatory act as follows:
(a)
all requirements of the regulatory act shall be fulfilled unless otherwise stated;
(b)
a type-approval certificate is not required;
(c)
tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 67 to 81;
(d)
the test report shall be drafted in accordance with Annex III;
(e)
Conformity of Production shall be ensured. |
|
B |
: |
Application of the regulatory act as follows: Same as for explanatory note ‘A’ with the exception that the tests and checks may be performed by the manufacturer themselves, subject to the agreement of the approval authority.
|
|
C |
: |
Application of the regulatory act as follows:
(a)
the technical requirements from the regulatory act shall be fulfilled, but with different transitional provision;
(b)
a type-approval certificate is not required;
(c)
tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 67 to 81;
(d)
the test report shall be drafted in accordance with Annex III;
(e)
Conformity of Production shall be ensured. |
|
IF |
: |
Systems, separate technical units or components shall meet the requirements if fitted to the vehicle |
|
n/a |
: |
Not applicable |
The specific provisions set out in Table 1 and Table 2 cannot be mixed or combined.
Table 1
Regulatory acts for EU type-approval of manually driven vehicles produced in small series pursuant to Article 41
|
|
Small series scheme I |
Small series scheme II |
||||
|
Item |
Subject |
Regulatory act |
M1 |
N1 |
M1 |
N1 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
|||||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
B (a) Interior arrangement (i) Radii and protrusion requirements for switches, pull-knobs and the like, controls and general interior fittings. The requirements of paragraphs 5.1 to 5.6 of UN Regulation No 21 may be waived at the request of the manufacturer. The requirements of paragraph 5.2 of UN Regulation No 21 with the exception of paragraphs 5.2.3.1, 5.2.3.2 and 5.2.4 of that Regulation shall apply. (ii) Energy absorption tests on the upper dashboard. Energy absorption tests on the upper dashboard shall only be performed when the vehicle is not fitted with at least two front airbags or two static four-point harnesses. (iii) Energy absorption test on the rear part of the seats: not applicable (b) Power-operation of windows, roof-panel systems and partition systems. All requirements of paragraph 5.8 of UN Regulation No 21 shall apply. |
not in scope |
B |
not in scope |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
B (a) General requirements (i) Specifications Requirements of paragraph 5.2 of UN Regulation No 17 shall apply with the exception of paragraph 5.2.3 of that Regulation. (ii) Strength tests for seat backrest and head restraints. The requirements of paragraph 6.2 of UN Regulation No 17 shall apply. (iii) Unlocking and adjustment tests. The test shall be performed in accordance with the requirements of Annex 7 to UN Regulation No 17. (b) Head restraints (i) Specifications. Requirements of paragraphs 5.4, 5.5, 5.6, 5.10, 5.11 and 5.12 of UN Regulation No 17 shall apply with the exception of paragraph 5.5.2 of that Regulation. (ii) Strength tests on head restraints. The test prescribed in paragraph 6.4 of UN Regulation No 17 shall be performed. (c) Special requirements regarding the protection of occupants from displaced luggage. The requirements of Annex 9 to UN Regulation No 17 may be waived at the request of the manufacturer. |
B |
B |
B |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation requirements B |
(a) Components X (b) Installation requirements B |
(a) Components X (b) Installation requirements B |
(a) Components X (b) Installation requirements B |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
B |
IF B |
B |
IF B |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
B (a) Liquid fuel tanks (b) Installation in vehicle |
B (a) Liquid fuel tanks (b) Installation in vehicle |
B (a) Liquid fuel tanks (b) Installation in vehicle |
B (a) Liquid fuel tanks (b) Installation in vehicle |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
B Shall apply to vehicles fitted with front airbags. May comply with A21 Frontal full-width impact instead, at the choice of the manufacturer. Vehicles not fitted with airbags shall comply with A22 Protective steering (in full) |
B Shall apply to vehicles fitted with front airbags. May comply with A21 Frontal full-width impact instead, at the choice of the manufacturer. Vehicles not fitted with airbags shall comply with A22 Protective steering (in full) Completed vehicles are deemed to comply with the frontal off-set impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
B |
B Completed vehicles are deemed to comply with the frontal off-set impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
B On voluntary basis |
B On voluntary basis Completed vehicles are deemed to comply with the frontal full-width impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
B |
B Completed vehicles are deemed to comply with the frontal full-width impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
B Shall apply to vehicles that do not comply with A20 Frontal off-set impact or A21 Frontal full-width impact |
B Shall apply to vehicles that do not comply with A20 Frontal off-set impact or A21 Frontal full-width impact |
B |
B |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
not in scope |
B Test A is required for vehicles with a maximum permissible mass of 1 500 kg or more if compliance with A20 Frontal off-set impact, A21 Frontal full-width impact or A22 Protective steering was not demonstrated. Test C is required only for vehicles which have a separate cab. Completed vehicles are deemed to comply with cab impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
not in scope |
B Test A is deemed to be fulfilled by means of A20 Frontal off-set impact, A21 Frontal full-width impact or A22 Protective steering. Test C is required only for vehicles which have a separate cab. Completed vehicles are deemed to comply with cab impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
B Head form test The manufacturer shall supply the technical service with suitable information concerning a possible impact of the head of the dummy against the structure of the vehicle or the side glazing, if made of laminated glazing. When such impact is proven likely to happen, then the partial test using the head form test described in paragraph 3.1 of Annex 8 to UN Regulation No 95 shall be conducted and the criterion specified in paragraph 5.2.1.1 of UN Regulation No 95 shall be met. In agreement with the technical service, the test procedure described in Annex 4 to UN Regulation No 21 may be used as an alternative to the test of UN Regulation No 95. Alternatively, a full-scale test in accordance with UN Regulation No 95 may be carried out. |
B Head form test The manufacturer shall supply the technical service with suitable information concerning a possible impact of the head of the dummy against the structure of the vehicle or the side glazing, if made of laminated glazing. When such impact is proven likely to happen, then the partial test using the head form test described in paragraph 3.1 of Annex 8 to UN Regulation No 95 shall be conducted and the criterion specified in paragraph 5.2.1.1 of UN Regulation No 95 shall be met. In agreement with the technical service, the test procedure described in Annex 4 to UN Regulation No 21 may be used as an alternative to the test of UN Regulation No 95. Alternatively, a full-scale test in accordance with UN Regulation No 95 may be carried out. Completed vehicles are deemed to comply with side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
B |
B Completed vehicles are deemed to comply with side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B |
B Completed vehicles are deemed to comply with the pole side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B |
B Completed vehicles are deemed to comply with rear impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
n/a |
n/a |
n/a |
n/a |
|
|
|
|
|
|
|
|
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
|||||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
C Date for refusal to grant EU type- approval: 7 January 2026 Date for the prohibition of the registration of vehicles: 7 July 2034 |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
IF B Date for refusal to grant EU type- approval: 7 July 2026 Date for the prohibition of the registration of vehicles: 7 July 2028 |
IF B Date for refusal to grant EU type- approval: 7 July 2026 Date for the prohibition of the registration of vehicles: 7 July 2028 |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. Date for refusal to grant EU type- approval: 7 July 2026 Date for the prohibition of the registration of vehicles: 7 July 2028 |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. Date for refusal to grant EU type- approval: 7 July 2026 Date for the prohibition of the registration of vehicles: 7 July 2028 |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B |
B |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
B |
B Date for refusal to grant EU type- approval: 7 July 2026 Date for the prohibition of the registration of vehicles: 7 July 2028 |
B |
B Date for refusal to grant EU type- approval: 7 July 2026 Date for the prohibition of the registration of vehicles: 7 July 2028 |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
(a) Components X (b) Installation B |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
B Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
B Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
B Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
B Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
B Vehicles shall be fitted with adequate windscreen washing and wiping devices |
B Vehicles shall be fitted with adequate windscreen washing and wiping devices |
B Vehicles shall be fitted with adequate windscreen washing and wiping devices |
B Vehicles shall be fitted with adequate windscreen washing and wiping devices |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation on vehicle B |
(a) Components X (b) Installation on vehicle B |
(a) Components X (b) Installation on vehicle B |
(a) Components X (b) Installation on vehicle B |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
A |
A |
A |
A |
|
|
|
|
|
|
|
|
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
|||||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
IF B |
IF B |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
IF B |
IF B |
B |
B |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
IF B |
IF B |
B |
B |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
IF B |
IF B |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B |
B |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
|
|
|
|
|
|
|
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
|||||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
(a) Components X (b) Installation on vehicle B |
(a) Components X (b) Installation on vehicle B |
(a) Components X (b) Installation on vehicle B |
(a) Components X (b) Installation on vehicle B |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
A The provisions of paragraph 8.3.1.1.1 of UN Regulation No 116 may be applied instead of paragraph 8.3.1.1.2 of that Regulation regardless of the type of powertrain. VAS: (a) Components X (b) Installation B |
A The provisions of paragraph 8.3.1.1.1 of UN Regulation No 116 may be applied instead of paragraph 8.3.1.1.2 of that Regulation regardless of the type of powertrain. VAS: (a) Components X (b) Installation B |
A The provisions of paragraph 8.3.1.1.1 of UN Regulation No 116 may be applied instead of paragraph 8.3.1.1.2 of that Regulation regardless of the type of powertrain. VAS: (a) Components X (b) Installation B |
A The provisions of paragraph 8.3.1.1.1 of UN Regulation No 116 may be applied instead of paragraph 8.3.1.1.2 of that Regulation regardless of the type of powertrain. VAS: (a) Components X (b) Installation B |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
B Only for vehicles fitted with lane keeping system, adaptive cruise control or other likewise systems |
B Only for vehicles fitted with lane keeping system, adaptive cruise control or other likewise systems |
B |
B |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. |
B Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level. |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
B Daytime Running Lamps (DRL) shall be fitted to a new type of vehicle |
B Daytime Running Lamps (DRL) shall be fitted to a new type of vehicle |
B Daytime Running Lamps (DRL) shall be fitted to a new type of vehicle |
B Daytime Running Lamps (DRL) shall be fitted to a new type of vehicle |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
B Only for vehicles fitted with electronically controlled anti-lock braking system |
B Only for vehicles fitted with electronically controlled anti-lock braking system |
B |
B |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF B |
IF B |
IF B |
IF B |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
n/a |
not in scope |
|
|
|
|
|
|
|
|
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
|||||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B |
B |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
No requirement yet |
No requirement yet |
No requirement yet |
No requirement yet |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF B |
IF B |
IF B |
IF B |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
n/a |
n/a |
B |
B |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF B |
No requirement yet |
IF B |
No requirement yet |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF B |
No requirement yet |
IF B |
No requirement yet |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
No requirement yet |
No requirement yet |
No requirement yet |
No requirement yet |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
No requirement yet |
No requirement yet |
No requirement yet |
No requirement yet |
|
|
|
|
|
|
|
|
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
|||||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
B Statement of compliance |
B Statement of compliance |
B Statement of compliance |
B Statement of compliance |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
B (a) General requirements (Paragraph 5 of UN Regulation No 11) All the requirements shall apply. (b) Performance requirements (Paragraph 6 of UN Regulation No 11) Only the requirements of paragraph 6.1.5.4 and paragraph 6.3 of UN Regulation No 11 shall apply. |
B (a) General requirements (Paragraph 5 of UN Regulation No 11) All the requirements shall apply. (b) Performance requirements (Paragraph 6 of UN Regulation No 11) Only the requirements of paragraph 6.1.5.4 and paragraph 6.3 of UN Regulation No 11 shall apply. |
B |
B |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
B (a) General specifications. The requirements of paragraph 5 of UN Regulation No 26 shall apply. (b) Particular specifications. The requirements of paragraph 6 of UN Regulation No 26 shall apply. |
not in scope |
B (a) General specifications. The requirements of paragraph 5 of UN Regulation No 26 shall apply. (b) Particular specifications. The requirements of paragraph 6 of UN Regulation No 26 shall apply. |
not in scope |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
not in scope |
B (a) General specifications. The requirements of paragraph 5 of UN Regulation No 61 shall apply (b) Particular specifications. The requirements of paragraph 6 of UN Regulation No 61 shall apply. |
not in scope |
B (a) General specifications. The requirements of paragraph 5 of UN Regulation No 61 shall apply (b) Particular specifications. The requirements of paragraph 6 of UN Regulation No 61 shall apply. |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
B |
B |
B |
B |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
B |
not in scope |
B |
not in scope |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
not in scope |
B |
not in scope |
B |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
B The hill start ability test of Regulation (EU) 2021/535, Annex XIII, Part 2, Section B, Point 5. may be waived at the request of the manufacturer. |
B The hill start ability test of Regulation (EU) 2021/535, Annex XIII, Part 2, Section B, Point 5. may be waived at the request of the manufacturer. |
B |
B |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF (a) Components X (b) Installation B |
IF (a) Components X (b) Installation B |
IF (a) Components X (b) Installation B |
IF (a) Components X (b) Installation B |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
not in scope |
A |
not in scope |
A |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
|
|
|
|
|
|
|
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
|||||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
A |
A |
A |
A |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
A Where the vehicle manufacturer uses an engine from another manufacturer, bench test data from the engine manufacturer are accepted provided that the engine management system is identical (i.e. having at least the same electronic control unit (ECU)). The power output test may be performed on a chassis dynamometer, taking into account the power loss in the transmission. |
A Where the vehicle manufacturer uses an engine from another manufacturer, bench test data from the engine manufacturer are accepted provided that the engine management system is identical (i.e. having at least the same electronic control unit (ECU)). The power output test may be performed on a chassis dynamometer, taking into account the power loss in the transmission. |
A |
A |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
A |
A |
A |
A |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
A Where the vehicle manufacturer uses an engine from another manufacturer, bench test data from the engine manufacturer are accepted provided that the engine management system is identical (i.e. having at least the same electronic control unit (ECU)). The power output test may be performed on a chassis dynamometer, taking into account the power loss in the transmission. |
A Where the vehicle manufacturer uses an engine from another manufacturer, bench test data from the engine manufacturer are accepted provided that the engine management system is identical (i.e. having at least the same electronic control unit (ECU)). The power output test may be performed on a chassis dynamometer, taking into account the power loss in the transmission. |
A |
A |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
not in scope |
not in scope |
not in scope |
not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
A |
A |
A |
A |
|
G8 |
Low-temperature tailpipe emissions in lab |
Regulation (EC) No 715/2007 |
A |
A |
A |
A |
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
The vehicle shall be fitted with an OBD system that shall be designed, constructed and installed as to enable it to identify types of deterioration or malfunction over the entire life of the vehicle and record at least the malfunction of the engine management system. The OBD-interface shall be able to communicate with commonly available diagnostic tools. |
The vehicle shall be fitted with an OBD system that shall be designed, constructed and installed as to enable it to identify types of deterioration or malfunction over the entire life of the vehicle and record at least the malfunction of the engine management system. The OBD-interface shall be able to communicate with commonly available diagnostic tools. |
A |
A |
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
A |
A |
|
G13 |
Recyclability |
Directive 2005/64/EC |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
A |
A |
A |
A |
|
|
|
|
|
|
|
|
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
|||||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
X |
X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858 UN Regulation No 156 |
X |
X |
X |
X |
Table 2
Regulatory acts for EU type-approval of fully automated vehicles (as defined in Article 3(22) of Regulation (EU) 2019/2144) produced in small series pursuant to Article 41
|
Item |
Subject |
Regulatory act(the scope of the regulatory act remains unchanged) |
Fully automated vehicles of categories N1, N2 and N3 without driver seat and without occupants |
Fully automated vehicles of categories N1, N2, N3, M1, M2, M3 without driver seat, with occupants |
Dual mode vehicles: vehicles with a driver seat designed and constructed to be driven by the driver in the ‘manual driving mode’ and to be driven by the automated driving system (ADS) without any driver supervision in the ‘fully automated driving mode’ |
Specific provisions to be applied if letter A is used (i.e. the approval is not possible under the regulatory act because it does not yet include specific requirements for fully automated vehicles) No provision shall apply if the vehicle category is not in the scope of the base regulatory act. |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
|||||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
not in scope |
A |
X for manual driving mode. A for fully automated driving mode |
All windows, roof-panels and partitions for use by occupants shall be equipped with an auto-reversing device in order to make a driver-controlled switch redundant. For bidirectional vehicles (i.e. vehicles with no distinguishable rear/front and that can be driven in both directions), requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
n/a |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
n/a |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
n/a |
A |
X |
For vehicle with no driver seat, any seat in the first seat row shall be considered to be a front passenger seat. Paragraphs 5.1.6.2.1 and 5.1.6.2.2 of UN Regulation No 14 are not applicable. |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
n/a |
A |
X |
For vehicles without driver seat, any seat in the first seat row shall be considered to be a front passenger seat. |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
n/a |
A |
X |
For vehicles without driver seat, any seat in the first seat row shall be considered to be a front passenger seat. The safety-belt reminder signal shall be transmitted to the automated driving system (ADS) and the remote intervention operator (if applicable) as defined in ►C2 Commission Implementing Regulation (EU) 2022/1426 (1) ◄ . |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
|
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
n/a |
X |
X |
|
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
n/a |
X |
X |
|
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
n/a |
X |
X |
|
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
X A (for bidirectional vehicles) |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
X A (for bidirectional vehicles) |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
X A (for bidirectional vehicles) |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The required malfunction or fault indication shall be replaced by a signal transmitted to the automated driving system and remote intervention operator (if applicable). |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The requirements for passenger compartment shall not apply to N vehicles with no passenger. The indications normally given to the driver ’ shall be sent to the ADS and the remote intervention operator (if applicable) |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
Not applicable |
A n/a for vehicles below 30 km/h |
X |
The ‘R’ point of the driver shall be considered to be the ‘R’ point of the foremost passenger. If the vehicle has no steering wheel or pedal cluster, the positioning of the steering wheel and pedal cluster shall not be taken into account. If the vehicle does not contain a driver or/and a co-driver seat, these positions should not be tested. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
n/a |
A n/a for vehicles below 30 km/h |
X |
The ‘R’ point of the driver shall be considered to be the ‘R’ point of the foremost passenger. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X |
|
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
n/a |
equipment |
equipment |
|
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
n/a |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
n/a |
A n/a for vehicles below 30 km/h |
X |
The collision test will be carried out on the side or sides as agreed between the manufacturer and type approval authority. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
n/a |
A n/a for vehicles below 30 km/h |
X |
The ‘R’ point of the driver’s seat shall be considered to be the ‘R’ point of the foremost passenger seat. The dynamic pole side impact test will be carried out on the side or sides as agreed between the manufacturer and type approval authority. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
n/a |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
n/a |
A |
X (for manual drivingmode) A (for fully automated driving mode) |
For fully automated driving mode, the ADS takes care of the functionality. |
|
|
|
|
|
|
|
|
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
|||||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
X A(for bidirectional vehicles) |
X A (for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
X A(for bidirectional vehicles) |
X A(for bidirectional vehicles) |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
|
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
n/a (functionality to be covered by the ADS) |
n/a (functionality to be covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality to be covered by the ADS) |
|
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
n/a (functionality to be covered by the ADS) |
n/a (functionality to be covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality to be covered by the ADS) |
|
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
n/a (functionality to be covered by the ADS) |
n/a (functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS) |
n/a (functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality to be covered by the ADS) |
|
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS) |
n/a (functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
n/a |
A |
X |
Point 4.1.3 of Annex 24 is not applicable (no R-point available in relation to the installation of the windscreen). Any front exterior forward-facing glazing shall be regarded as windscreen. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS) |
n/a (functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
X |
X |
|
|
|
|
|
|
|
|
|
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
|||||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The basic steering (mechanical) requirements apply however: — the requirements applicable to the steering control (e.g. max steering forces) are not applicable; — the failure provisions and performance at 5.3 are not relevant if there’s no driver but the failure notification should be made (digitally) available to the ADS and the remote intervention operator (if applicable). — The provisions of Annex 6-complex electronic systems need to be fulfilled and may be covered by the ADS safety concept. The ADS shall take care of the tasks assigned to the driver and driver steering assistance system. |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS) |
n/a (functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS) |
n/a (functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated mode) |
Activation of the brakes managed by the ADS in replacement of the driver and driver assistant systems. Each vehicle shall be fitted where applicable with — a service braking system — a secondary braking system — a parking braking system — an endurance braking system. (for vehicle categories covered by UN Regulation No 13) All Annexes to UN Regulation No 13, except for Annex 5 (Additional provisions applicable to certain vehicles as specified in the ADR), shall remain applicable. All muscular generated performances (e.g. secondary brake) shall be replaced by alternative supply. (to be performed by the ADS- need for a special test mode). Issue of failure to be covered (no driver as fallback). All the tell tales, indicators, warnings and information in accordance to UN Regulation No 13 or UN Regulation No 13-H (depending on the vehicle category) shall be sent to the ADS and the remote intervention operator (if applicable). When more than one control is required in UN Regulation No 13 (e.g. paragraph 5.2.1.2.1) this shall be replaced by two independent power sources. e.g. service brake activation and parking braking brake shall be activated by actuators with separated energy reserves, actuators and logic. The ADS safety concept shall cover the electronic systems of the braking system (including the interfaces and interactions with any other affected electronic systems of the vehicle). The ADS takes care of the tasks assigned to the driver and braking assistance systems. |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
|
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS |
n/a(functionality covered by the ADS) |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS |
n/a (functionality covered by the ADS |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS |
n/a (functionality covered by the ADS |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
n/a (functionality covered by the ADS) |
n/a (functionality covered by the ADS) |
X for manual driving mode Not applicable for fully automated driving mode (functionality covered by the ADS) |
|
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated mode) |
In the case of vehicles equipped with a Run-Flat Warning System the warning signal and the run-flat malfunction signal shall be replaced by signals transmitted to the ADS and the remote intervention operator (if applicable). |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
|
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The warning signal shall be sent to the ADS and the remote intervention operator (if applicable). |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The warning signal shall be sent to the ADS and the remote intervention operator (if applicable). |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
A |
A |
X |
The maximum speed warning label (in vehicle) shall not be required. The ADS shall not exceed the maximum speed capability of the tyres prescribed by the vehicle manufacturer. |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
|
|
|
|
|
|
|
|
|
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
|||||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
Test mode needed. In addition to the requirements EMC tests described in Annexes 4 to 22 to UN Regulation No 10, the following procedure before and during initial EMC tests shall be followed: 1. When a fully automated vehicle with an ADS is EMC tested, the ADS functions should be switched on and also work in active mode. However certain limitations in use case can be observed. Therefore, before executing the EMC test, the type-approval authority needs to be consulted about the test program to agree about the Pass/Fail criteria proposal made by the EMC lab according to paragraph 6.1.2 of UN Regulation No 10. Before testing the Technical Service has to prepare a test plan in conjunction with the manufacturer, which contains at least mode of operation, stimulated function(s), monitored function(s), pass/fail criterion (criteria) and intended emissions. 2. The manufacturer of the vehicle or Electric/electronic subassembly (ESA) shall fill in the information according to UN Regulation 10, Annex 2A or 2B. The EMC lab shall make this available as an annex to the test report. 3. In case if a remote intervention is used and could influence the behaviour of the vehicle the remote intervention should be part of the EMC test plan. 4. When it’s needed during the initial test, to install Ferrite blocks or aluminium foil on several elements to pass the EMC tests, it proves that the EMC design was weak and potentially prone to variation. Therefore the initial tests can never be used for further revision or extension for further vehicles or adding/changing ESAs (Electronic Sub-Assemblies) to the vehicle/DUTs. |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
Requirements are not applicable except that the speed signal shall be send to the ADS |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The odometer signal shall be send to the ADS |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode A for fully automated) driving mode |
Test mode needed. The speed management and limitation shall be ensured by ADS. |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) (functionality covered by the ADS) |
|
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
n/a |
A |
X (for manual driving mode) A (for fully automated driving mode) |
In the case of part or parts of the heating system in the passenger compartment, and in the case of overheating, the temperature of the parts shall not exceed 110 °C (70 °C for M2 and 80 °C for M3). The activation and adjustment of the heating system can be managed by the ADS and/or passengers or remote intervention operator (if applicable). |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The requirements shall remain the same, but in case of malfunctioning, the information shall be sent to ADS and the remote intervention operator (if applicable). The activation of the lights is managed by the ADS. For bidirectional vehicles, requirements shall be met in both directions unless it is incompatible with the use in agreement with the type-approval authority. |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The control of the headlamp cleaner shall be managed by the ADS. |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated mode) |
not in scope |
|
|
|
|
|
|
|
|
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
|||||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X (for manual driving mode) n/a (for fully automated driving mode) |
|
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
No requirement yet |
No requirement yet |
No requirement yet |
|
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
n/a |
n/a |
X |
|
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
A |
A |
A for fully automated driving mode X for manual driving mode |
Specific ADS data elements are covered in ►C2 Implementing Regulation (EU) 2022/1426 ◄ |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
Covered by ►C2 Implementing Regulation (EU) 2022/1426 ◄ |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
Covered by ►C2 Implementing Regulation (EU) 2022/1426 ◄ |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
No requirement yet |
No requirement yet |
No requirement yet |
No requirement yet |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
X |
X |
X |
Covered by ►C2 Implementing Regulation (EU) 2022/1426 ◄ |
|
|
|
|
|
|
|
|
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
|||||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
For bidirectional vehicles, requirements shall be met in both directions unless it is incompatible with the use in agreement with the type-approval authority. |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The ADS shall also be tested for manouvrability (reverse gear). The ADS shall take care of the tasks assigned to the driver (e.g. activation of the reverse gear). |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
n/a |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The visual signal of the door closure warning system shall be replaced by a signal transmitted to the ADS and the remote intervention operator (if applicable). The equipment of side doors with locking devices shall be subject to the discretion of the manufacturer. The primary door controls which normally would be accessible by the driver, would need to be accessible either from a primary seating position (if applicable) or adjacent to each door. The ADS shall ensure that the vehicle can only move if doors are closed. |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
A |
X |
X |
Vehicle access requirements do not apply where there is no vehicle cab. |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
not in scope |
A |
A (for fully automated driving mode) |
Sensors fitted to the ADS vehicle which are necessary to perform the Dynamic Driving Task can be excluded in a similar manner as camera monitor systems devices if they meet the general requirements on camera monitor devices in paragraph 6.2.2.1 of UN Regulation 46. The ‘R’ point of the driver referred shall be considered to be the ‘R’ point of the foremost passenger in case there is no driver seat. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
A |
A |
A |
Sensors fitted to the ADS vehicle which are necessary to perform the Dynamic Driving Task can be excluded in a similar manner as camera monitor systems devices if they meet the general requirements on camera monitor devices in paragraph 6.2.2.1 of UN Regulation 46. The ‘R’ point of the driver referred shall be considered to be the ‘R’ point of the foremost passenger in case there is no driver seat. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X A for bidirectional vehicles |
X A for bidirectional vehicles |
X |
For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
Not in scope |
A |
X (for manual driving mode) A (for fully automated mode) |
Fully applicable. For bidirectional vehicles, requirements shall be met in both directions. Alternative requirements leading to an equivalent level of safety to the satisfaction of the type-approval authority are permitted if meeting all the requirements in both directions is incompatible with the bidirectional use. |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
|
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
A |
A. |
A (for fully automated mode) X (for manual driving mode) |
Mass in running order shall exclude mass of the driver if there is no on-board operator. The ADS sensors above 2 metres are not included in the maximum dimensions in accordance with the provisions of Regulation (EU) 2021/535, Annex XIII. |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The indication to driver that the mechanical coupling is locked/unlocked shall be addressed to the ADS and the remote intervention operator (if applicable). |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
Not in scope |
Not in scope |
Not in scope |
Fully automated vehicles intended for the transportation of dangerous goods cannot be approved. |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
Not in scope |
A |
X (for manual driving mode) A (for fully automated mode) |
Buses without a roof and trolley buses are out of scope. In general the tasks normally expected by the driver under UN Regulation No 107 shall be covered in the ADS safety concept. The requirements of paragraphs 7.2.2.1.1, 7.2.2.1.2 and 7.2.2.1.3 as defined in Annex 3 to UN-Regulation No 107 shall not apply. All required information normally displayed or noticed to the driver or information to passengers in case of an emergency shall be transferred to the ADS, the on-board operator and the remote intervention operator (e.g. fire suppression system) The ADS shall take care of power operated doors. The ADS shall take care of the reaction to fire as part of the ADS safety concept (e.g. emergency manoeuvre and transfer to the safe state), doors automatically unlocked when safe to do so. In case of emergency, the ADS shall take care of the emergency lighting system as part of the ADS safety concept. Once activated, the emergency lighting system shall remain active for at least 30 minutes. This active function shall be displayed as well to the remote intervention operator who may deactivate the emergency lighting system. The kneeling system shall in ADS operation automatically be actuated to achieve required step height. Also prevention system shall be part of the ADS safety concept to prevent the feet/legs of passengers boarding the vehicle from geting stuck underneath the vehicle during lowering process. |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
Not in scope |
X |
X |
|
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
Not in scope |
X |
X |
|
|
|
|
|
|
|
|
|
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
|||||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
Test mode necessary. Manufacturer to define how to perform the test in accordance with the technical justification in agreement with technical service. Highest value measured in manual or/and in autonomous mode shall be considered for type approval. Vehicles having overall sound levels complying with the requirements in paragraph 6.2.8 of UNECE Regulation No 138(1) with a margin of +3 dB(A), are not required to be equipped with Acoustic Vehicle Alerting System (AVAS). The requirements laid down in paragraph 6.2.8 of that Regulation for one-third octave bands and the requirements laid down in paragraph 6.2.3 of that Regulation for the frequency shift as defined in paragraph 2.4 of that Regulation (‘frequency shift’) shall not apply to those vehicles to determine the need for AVAS independent whether the vehicles is driven in manual or autonomous mode during the test. The R point of the driver seat shall be considered to be the lowest R point of the passenger seats in the 1st seat row. Used test procedure/special arrangement to be recorded in the test report. |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The manufacturer shall define a test mode in order to allow testing on a chassis dynamometer and communicate the method to the relevant approval authorities. The required driver warning and inducement system shall be replaced by signals transmitted to the automated driving system, and remote intervention operator (if applicable). It shall be clearly indicated to the remote intervention operator when the inducement will be activated. |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
A |
A |
X (for manual driving mode) A (for fully automated driving mode) |
The manufacturer shall define a test mode in order to allow testing on a chassis dynamometer and communicate the method to the relevant approval authorities. |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
A |
A |
X (for manual driving mode) A (for automated driving mode) |
The required driver warning and inducement system shall be replaced by signals transmitted to the automated driving system and remote intervention operator (if applicale). It shall be clearly indicated to the remote intervention operator when the inducement will be activated. |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
A |
A |
X (for manual driving mode) A (for automated driving mode) |
The manufacturer shall define a test mode in order to perform the verification testing procedure and communicate the method to the relevant approval authorities. |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
X (for manual driving mode) A (for automated driving mode) |
The manufacturer shall define a test mode in order to allow testing on the road and communicate the method to the relevant approval authorities. The required driver warning and inducement system shall be replaced by signals transmitted to the automated driving system, and remote intervention operator (if applicable). It shall be clearly indicated to the remote intervention operator when the inducement will be activated. |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
X (for manual driving mode) |
The manufacturer shall define a test mode in order to allow testing on the road and communicate the method to the relevant approval authorities. |
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
|
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
X |
X |
X |
|
|
G8 |
Low-temperaturetailpipe emissions in lab |
Regulation (EC) No 715/2007 |
A |
A |
X (for manual driving mode) A (for automated driving mode) |
The manufacturer shall define a test mode in order to allow testing on a chassis dynamometer and communicate the method to the relevant approval authorities. The required driver warning and inducement system shall be replaced by signals transmitted to the automated driving system and remote intervention operator (if applicale). It shall be clearly indicated to the remote intervention operator when the inducement will be activated. |
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
A |
A |
X (for manual driving mode) A (for automated driving mode) |
The required Malfunction Indicator Light (MIL) shall be replaced by a signal transmitted to the automated driving system, and remote intervention operator (if applicable). |
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
|
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
|
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
|
|
G13 |
Recyclability |
Directive 2005/64/EC |
X |
X |
X |
|
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
n/a |
X |
X |
|
|
|
|
|
|
|
|
|
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
|||||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
X |
X |
|
|
H2 |
Software update |
Regulation (EU) 2018/858 UN Regulation No 156 |
X |
X |
X |
|
|
(1)
Commission Implementing Regulation (EU) 2022/1426 of 5 August 2022 laying down rules for the application of Regulation (EU) 2019/2144 of the European Parliament and of the Council as regards uniform procedures and technical specifications for the type-approval of the automated driving system (ADS) of fully automated vehicles (OJ L 221, 26.8.2022, p. 1). |
||||||
Appendix 2
Requirements for EU individual vehicle approval pursuant to Article 44
1. APPLICATION
For the purpose of application of this Appendix, a vehicle is deemed to be new where:
it has never been registered previously; or
it has been registered for less than six months at the time of the application for individual vehicle approval.
A vehicle shall be considered registered where it has obtained a permanent, temporary or short-term administrative authorisation for entry into service in road traffic, involving its identification and the issuing of a registration number ( 12 ).
2. ADMINISTRATIVE PROVISIONS
2.1. Categorisation of the vehicle
Vehicles shall be categorised in accordance with the criteria set out in Annex I as follows:
the actual number of seating positions shall be taken into consideration; and
the technically maximum permissible laden mass shall be the maximum mass stated by the manufacturer in the country of origin and available in his official documentation.
Where it is not possible to easily determine the vehicle category because of the design of the bodywork, the conditions set out in Annex I shall apply.
2.2. Application for individual vehicle approval
The applicant shall submit an application to the approval authority accompanied by all relevant documentation necessary for the operation of the approval procedure.
Where the submitted documentation is incomplete, falsified or forged the application for approval shall be rejected.
Only one application for a particular vehicle may be submitted in only one Member State. The approval authority may require from the applicant a written commitment that only one application will be submitted in the Member State of the approval authority.
By a particular vehicle, it shall be understood a physical vehicle the VIN of which is clearly identified.
However, any applicant may apply for EU individual vehicle approval in another Member State in respect of another particular vehicle with technical characteristics identical or similar to the one that has been granted an EU individual vehicle approval.
The model of the application form and the layout of the file shall be laid down by the approval authority.
The particulars of the vehicle requested may only consist in an appropriate selection of the information included in Annex I.
The technical requirements to be complied with are those laid down in point 4.
The technical requirements shall be those applicable to vehicles belonging to a type of vehicle currently in production, in relation to the date of the submission of the application.
With respect to the tests required under the regulatory acts listed in this Annex, the applicant shall supply a statement of compliance with recognised international standards or regulations. The statement in question may only be issued by the vehicle manufacturer.
‘Statement of compliance’ shall mean a statement issued by the office or department within the manufacturer's organisation that is duly authorised by the management to fully engage the legal responsibility of the manufacturer with respect to the design and the construction of a vehicle.
The regulatory acts for which such a statement has to be supplied shall be those referred to in point 4.
Where a statement of compliance gives rise to uncertainty, the applicant may be required to obtain from the manufacturer a piece of evidence, including a test report, in order to corroborate the manufacturer's statement.
2.3. Technical services entrusted with individual vehicle approvals
The technical services entrusted with individual vehicle approvals shall be of category A as referred to in Article 68(1).
By way of derogation from the requirement to demonstrate their compliance with the standards listed in Appendix 1 to Annex III, technical services shall comply with the following standards:
EN ISO/IEC 17025:2005 when they perform tests themselves;
EN ISO/IEC 17020:2012 when they check compliance of the vehicle with the requirements included in this Appendix.
Where specific tests requiring specific skills have to be conducted at the request of the applicant, they shall be conducted by one of the technical services notified to the Commission at the choice of the applicant.
2.4. Test reports
Test reports shall be drafted in accordance with paragraph 5.10.2 of standard EN ISO/IEC 17025:2005.
Test reports shall be drafted in one of the languages of the Union determined by the approval authority.
Where in application of point 2.3(c) a test report has been issued in a Member State other than the one entrusted with the individual vehicle approval, the approval authority may require that the applicant submits a true translation of the test report.
Test reports shall include a description of the vehicle tested, including its identification. The parts that play a significant role with regard to the results of the tests shall be described and their identification number reported.
At the request of an applicant, a test report delivered for a system related to a particular vehicle may be presented repeatedly either by the same or another applicant for the purposes of individual approval of another vehicle.
In such a case, the approval authority shall ensure that the technical characteristics of the vehicle are properly inspected against the test report.
Inspection of the vehicle and the documentation accompanying the test report shall demonstrate that the vehicle for which an individual approval is sought has the same characteristics as the vehicle described in the report.
Only authenticated copies of a test report may be submitted.
Test reports referred to in point (d) do not include the reports drawn up in order to grant the individual vehicle approval.
2.5. In the individual vehicle approval procedure each particular vehicle shall be inspected physically by the technical service.
No exemption to this principle shall be permitted.
2.6. Where the approval authority is satisfied that the vehicle meets the technical requirements specified in this Appendix and conforms to the description included in the application, it shall grant approval in accordance with Article 44.
2.7. The certificate of approval shall be drafted in accordance with Article 44.
2.8. The approval authority shall keep record of all approvals granted under Article 44.
3. REVIEW OF THE TECHNICAL REQUIREMENTS
The list of the technical requirements included in point 4 shall be regularly reviewed in order to take account of the results of the harmonisation work in progress at the World Forum for Harmonization of Vehicle Regulations (WP.29) in Geneva and legislative developments in the third countries.
4. TECHNICAL REQUIREMENTS
Part I: Vehicles belonging to category M1
|
Item |
Regulatory act reference |
Alternative requirements |
|
1 |
Council Directive 70/157/EEC (1) (Permissible sound level) |
Drive-by test (a) A test shall be conducted in accordance with the ‘Method A’ referred to in Annex 3 to UN Regulation No 51. Limits are those specified in point 2.1 of Annex I to Directive 70/157/EEC. 1 decibel in addition to the permitted limits shall be allowed. (b) The test track shall comply with Annex 8 to UN Regulation No 51. A test track having different specifications may be used under the condition that correlation tests have been conducted by the technical service. A correction factor shall be applied if necessary. (c) Exhaust systems containing fibrous materials need not be conditioned as prescribed in Annex 5 to UN Regulation No 51. Stationary test A test shall be conducted in accordance with paragraph 3.2 of Annex 3 to UN Regulation No 51. |
|
2A |
Regulation (EC) No 715/2007 (Emissions (Euro 5 and Euro 6) light duty vehicles/access to information) |
Tailpipe emissions (a) A type I test shall be conducted in accordance with Annex III to Regulation (EC) No 692/2008 using the deterioration factors set out in point 1.4 of Annex VII to Regulation (EC) No 692/2008. The limits to be applied shall be those specified in Table I and Table II in Annex I to Regulation (EC) No 715/2007. (b) The vehicle shall not be required to exhibit 3 000 km as mentioned in paragraph 3.1.1 of Annex 4 to UN Regulation No 83. (c) The fuel to be used for the test shall be the reference fuel as prescribed in Annex IX to Regulation (EC) No 692/2008. (d) The dynamometer shall be set up in accordance with the technical requirements set out in paragraph 3.2 of Annex 4 to UN Regulation No 83. (e) The test referred to in point (a) shall not be conducted where it can be shown that the vehicle complies with the California Code Regulations referred to in point 2.1.1 of Annex I to Regulation (EC) No 692/2008. Evaporative emissions For petrol-fuelled engines, the presence of an evaporate emissions control system shall be required (e.g. a charcoal canister). Crankcase emissions The presence of a device for recycling crankcase gases shall be required. OBD (a) The vehicle shall be fitted with an OBD system. (b) OBD-interface must be able to communicate with common diagnostic tools used for periodic technical inspections. Smoke opacity (a) Vehicles equipped with a diesel-fuelled engine shall be tested in accordance with the tests methods referred to in Appendix 2 to Annex IV to Regulation (EC) No 692/2008. (b) The corrected value of the absorption coefficient shall be affixed conspicuously and in a readily accessible place. CO2 emissions and fuel consumption (a) A test shall be conducted in accordance with Annex XII to Regulation (EC) No 692/2008. (b) The vehicle shall not be required to exhibit 3 000 km as requested in paragraph 3.1.1 of Annex 4 to UN Regulation No 83. (c) Where the vehicle complies with the California Code Regulations referred to in point 2.1.1 of Annex I to Regulation (EC) No 692/2008 and therefore no test of tailpipe emissions is required to be performed, Member States shall calculate CO2 emissions and fuel consumption with the formula laid down in the explanatory notes (b) and (c). Access to information The provisions regarding access to information shall not apply. Power measurement (a) The applicant shall submit a statement from the manufacturer stating the maximum engine power output in kW as well as the corresponding engine speed in revolutions per minute. (b) An engine power output curve providing the same information may alternatively be provided by the applicant. |
|
3A |
UN Regulation No 34 (Fuel tanks — Rear protective devices) |
Fuel tanks (a) Fuel tanks shall comply with paragraph 5 of UN Regulation No 34 with the exception of paragraphs 5.1, 5.2 and 5.12. In particular, they shall comply with paragraphs 5.9 and 5.9.1 but no dripping test shall be conducted. (b) LPG or CNG tanks shall be type-approved in accordance with UN Regulation No 67, series of amendments 01, or UN Regulation No 110 (a), respectively. Specific provisions for fuel tanks made of a plastic material The applicant shall submit a statement from the manufacturer establishing that the fuel tank on the particular vehicle, the VIN of which has to be specified, complies either with at least one of the following: — FMVSS No 301 (Fuel system integrity); or — Annex 5 to UN Regulation 34. Rear protective device The rear part of the vehicle shall be constructed in accordance with paragraphs 8 and 9 of UN Regulation No 34. |
|
3B |
UN Regulation No 58 (Rear underrun protection) |
The rear part of the vehicle shall be constructed in accordance with paragraph 2 UN Regulation No 58. It is sufficient that the requirements set out in paragraph 2.3 are fulfilled. |
|
4A |
Regulation (EU) No 1003/2010 (Rear registration plate space) |
Space, inclination, angles for visibility and position of the registration plate shall comply with Regulation (EU) No 1003/2010. |
|
5A |
UN Regulation No 79 (Steering equipment) |
Mechanical systems (a) The steering mechanism shall be built as to self-centre. In order to check compliance with this provision, a test shall be conducted in accordance with paragraphs 6.1.2 and 6.2.1 of UN Regulation No 79. (b) The failure of the power steering equipment shall not lead to a complete loss of control of the vehicle. Complex electronic vehicle control system (‘Drive-by wire’ devices) Complex electronic control system shall be permitted only if they comply with Annex 6 to UN Regulation No 79. |
|
6A |
UN Regulation No 11 (Door latches and hinges) |
Compliance with paragraph 6.1.5.4 of UN Regulation No 11. |
|
7A |
UN Regulation No 28 (Audible warning) |
Components The audible warning devices are not required to be type-approved in accordance with UN Regulation No 28. However, they shall emit a continuous sound as required in paragraph 6.1.1 of UN Regulation No 28. Installation on vehicle (a) A test shall be conducted in accordance with paragraph 6.2 of UN Regulation No 28. (b) The maximum sound pressure level shall be in accordance with paragraph 6.2.7. |
|
8A |
UN Regulation No 46 (Indirect vision devices) |
Components (a) The vehicle shall be fitted with the rear-view mirrors prescribed in paragraph 15.2 of UN Regulation No 46. (b) They are not required to be type-approved in accordance with UN Regulation No 46. (c) The radii of curvature of the mirrors shall not cause significant image distortions. At the discretion of the technical service, the radii of curvature shall be checked in accordance with the method described in Annex 7 to UN Regulation No 46. The radii of curvature shall not be less than those required by paragraph 6.1.2.2.4 of UN Regulation No 46. Installation on vehicle Measurement shall be conducted in order to ensure that the fields of vision comply with paragraph 15.2.4. of UN Regulation No 46. |
|
9B |
UN Regulation No 13-H (Braking) |
General provisions (a) The braking system shall be built in accordance with paragraph 5 of UN Regulation No 13-H. (b) Vehicles shall be fitted with an electronic antilock braking system acting on all wheels. (c) The performances of the braking system shall comply with Annex III to UN Regulation No 13-H. (d) For those purposes, road tests shall be conducted on a track the surface of which possesses high adhesion. The test on the parking brake shall be conducted on a 18 % gradient (up and down). Only those tests mentioned under the headings ‘Service brake’ and ‘Parking brake’ below shall be conducted. In each case, the vehicle shall be in fully laden conditions. (e) The road test referred to in point (d) shall not be conducted where the applicant can submit a statement from the manufacturer establishing that the vehicle complies either with UN Regulation No 13-H, including supplement 5, or with FMVSS No 135. Service brake (a) A ‘Type 0’ test as prescribed in paragraphs 1.4.2 and 1.4.3 of Annex 3 to UN Regulation No 13-H shall be conducted. (b) In addition, a ‘Type I’ test as prescribed in paragraph 1.5 of Annex 3 to UN Regulation No 13-H shall be conducted. Parking brake A test shall be conducted in accordance with paragraph 2.3 of Annex 3 to UN Regulation No 13-H. |
|
10A |
UN Regulation No 10 (Radio interference (electromagnetic compatibility)) |
Components (a) Electrical/electronic sub-assemblies are not required to be type-approved in accordance with UN Regulation No 10. (b) However, electric/electronic devices retrofitted shall comply with UN Regulation No 10. Emitted electromagnetic radiations The applicant shall submit a statement from the manufacturer establishing that the vehicle complies with UN Regulation No 10 or with the following alternative standards: — Broadband electromagnetic radiation: CISPR 12 or SAE J551-2; or — Narrowband electromagnetic radiation: CISPR 12 (off-board) or 25 (in-board) or SAE J551-4 and SAE J1113-41. Immunity tests Immunity test shall be waived. |
|
12A |
UN Regulation No 21 (Interior fittings) |
Interior arrangement (a) With respect to the requirements on energy absorption, the vehicle shall be deemed to comply with UN Regulation No 21 if the vehicle is fitted with at least two front airbags, one inserted into the steering wheel and the other into the dashboard. (b) Where the vehicle is fitted with only one front air bag inserted in the steering wheel, the dashboard shall be made up of energy absorbing materials. (c) The technical service shall check that there are no sharp edges in the zones defined in paragraphs 5.1 to 5.7 of UN Regulation No 21. Electrical controls (a) Power-operated windows, roof-panel systems and partitioning systems shall be tested in accordance with paragraph 5.8 of UN Regulation No 21. The sensitivity of auto-reverse systems referred to in paragraph 5.8.3 may diverge from the requirements set out in paragraph 5.8.3.1.1 of UN Regulation No 21. (b) Electric windows which cannot be closed when the ignition is off shall be exempt from the requirements concerning auto-reverse systems. |
|
13A |
UN Regulation No 18 (Anti-theft and immobiliser) |
(a) In order to prevent unauthorised use, the vehicle shall be fitted with: — a locking device as defined in paragraph 2.3 of UN Regulation No 18; and — an immobiliser which meets the technical requirements of paragraph 5 of UN Regulation No 18; (b) If, in accordance with point (a), an immobiliser has to be retrofitted, it shall be of an approved type in accordance with UN Regulations No 18, No 97, or No 116. |
|
14A |
UN Regulation No 12 (Protective steering) |
(a) The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, the VIN of which has to be specified, complies with at least one of the following: — UN Regulation No 12; — FMVSS No 203 (Impact protection for the driver from the steering control system) including FMVSS No 204 (Steering control rearward displacement); — Article 11 of JSRRV. (b) A test in accordance with Annex 3 to UN Regulation No 12 may be conducted on a production vehicle at the request of the applicant. The test shall be conducted by a technical service that has been designated for carrying out this test. A detailed report shall be issued by that technical service to the applicant. |
|
15A |
UN Regulation No 17 (Seat strength — head restraints) |
Seats, seat anchorages and adjustment systems The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, the VIN of which has to be specified, complies with at least one of the following: — UN Regulation No 17; or — FMVSS No 207 (Seating systems). Head restraints (a) Where the statement is based on FMVSS No 207, the head restraints shall fulfil, in addition, the requirements of paragraph 5 and Annex 4 to UN Regulation No 17. (b) Only the tests described in paragraphs 5.12, 6.5, 6.6 and 6.7 of UN Regulation No 17 shall be conducted. (c) In the other event, the applicant shall submit a statement from the manufacturer establishing that the particular vehicle, the VIN of which has to be specified, complies with FMVSS No 202a (Head restraints). |
|
16A |
UN Regulation No 26 (Exterior projections) |
(a) The external surface of the bodywork shall comply with the general requirements included in paragraph 5 of UN Regulation No 26. (b) At the discretion of the technical service the provisions referred to in paragraphs 6.1, 6.5, 6.6, 6.7, 6.8 and 6.11 of UN Regulation No 26 shall be checked. |
|
17A, 17B |
UN Regulation No 39 (Speedometer — reverse gear) |
Speedometer equipment (a) The dial shall comply with paragraphs 5.1 to 5.1.4 of UN Regulation No 39. (b) Where the technical service wants to verify that the speedometer is calibrated with sufficient accuracy, it may require the tests prescribed in paragraph 5.2 of UN Regulation No 39 to be conducted. Reverse gear The gear mechanism shall include a reverse gear. |
|
18A |
Regulation (EU) No 19/2011 (Statutory plates) |
VIN (a) The vehicle shall be fitted with a VIN comprising a minimum of 8 and a maximum of 17 characters. VIN comprising 17 characters shall fulfil the requirements set out in international standards ISO 3779:1983 and 3780:1983. (b) VIN shall be located in a clearly visible and accessible position in such a way as it cannot be obliterated or deteriorate. (c) Where no VIN is stamped in the chassis or in the body, a Member State may require the applicant that the VIN is retrofitted in application of its national law. In such a case, the competent authority of that Member State shall supervise the operation. Statutory plate The vehicle shall be fitted with an identification plate affixed by the vehicle manufacturer. No additional plate shall be requested after the approval by the approval authority has been granted. |
|
19A |
UN Regulation No 14 (Seat belt anchorages) |
The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, the VIN of which has to be specified, complies with at least one of the following: — UN Regulation No 14; — FMVSS No 210 (Seat belt assembly anchorages); or — Article 22-3 of JSRRV. |
|
20A |
UN Regulation No 48 (Installation of lighting and light signalling devices) |
(a) The lighting installation shall meet the requirements of UN Regulation No 48, series of amendments 03, with the exception of the requirements of Annexes 5 and 6 to that Regulation. (b) No exemption shall be permitted in respect of the number, the essential design characteristics, the electrical connections, and the colour of light emitted or retro-reflected of the lights and signalling devices referred to in items 21 to 26 and in items 28 to 30. (c) Lights and signalling devices that, for the purpose of fulfilling the requirements of point (a) must be retrofitted shall bear an ‘EU’ type-approval mark. (d) Lamps fitted with gas-discharged light source are only permitted in conjunction with the installation of headlamp cleaning device and an automatic headlamp-levelling device where appropriate. (e) Headlamp dipped-beams shall be adapted to the direction of traffic legally in force in the country where the vehicle is granted approval. |
|
21A |
UN Regulation No 3 (Retro reflectors) |
Where necessary, two additional retro reflectors bearing an ‘EU’ approval mark shall be added at the rear, the position of which shall comply with UN Regulation No 48. |
|
22A |
UN Regulations No 7, No 87 and No 91 (End-outline, front position (side), rear-position (side), stop, side marker, daytime running lamps) |
The requirements set out in the UN Regulations No 7, No 87 and No 91 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
23A |
UN Regulation No 6 (Direction indicators) |
The requirements set out in UN Regulation No 6 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
24A |
UN Regulation No 4 (Rear registration plate lamps) |
The requirements set out in UN Regulation No 4 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
25C, 25E, 25F |
UN Regulations No 98, No 112 and No 123 (Headlamps (including bulbs)) |
(a) The illumination produced by the passing beam of the headlamps fitted to the vehicle shall be checked under paragraph 6 of UN Regulation No 112 concerning headlamps emitting an asymmetrical passing beam. The tolerances included in Annex 5 to that Regulation may be referred to for that purpose. (b) The same requirement shall be fulfilled for the passing beam of headlamps covered by UN Regulation No 98 or No 123. |
|
26A |
UN Regulation No 19 (Front fog lamps) |
The requirements set out in UN Regulation No 19 shall not apply. However, the correct functioning of the lights if fitted shall be checked by the technical service. |
|
27A |
Regulation (EU) No 1005/2010 (Towing hooks) |
The requirements set out in Regulation (EU) No 1005/2010 shall not apply. |
|
28A |
UN Regulation No 38 (Rear fog lamps) |
The requirements set out in UN Regulation No 38 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
29A |
UN Regulation No 23 (Reversing lamps) |
The requirements set out in UN Regulation No 23 shall not apply. However, the correct functioning of the lights if fitted shall be checked by the technical service. |
|
30A |
UN Regulation No 77 (Parking lamps) |
The requirements set out in UN Regulation No 77 shall not apply. However, the correct functioning of the lights if fitted shall be checked by the technical service. |
|
31A |
UN Regulation No 16 (Seat belts and restraint systems) |
Components (a) Seat belts shall not be required to be type-approved in accordance with UN Regulation No 16. (b) However, each seat belt shall bear an identification label. (c) The indications on the label shall be consistent with the decision concerning seat belt anchorages (Re: entry 19). Installation requirements (a) The vehicle shall be fitted with seat belts in accordance with the requirements set out in Annex XVI to UN Regulation No 16. (b) Where a number of seat belts have to be retrofitted in accordance with point (a), they shall be of an approved type in accordance with UN Regulation No 16. |
|
32A |
UN Regulation No 125 (Forward vision) |
(a) No obstruction in the 180° forward field of vision of the driver as defined in paragraph 5.1.3 of UN Regulation No 125 shall be permitted. (b) By derogation from point (a), the ‘A pillars’ and the equipment listed in paragraph 5.1.3 of UN Regulation No 125 shall not be considered as obstruction. (c) The number of ‘A pillars’ shall not exceed 2. |
|
33A |
UN Regulation No 121 (Identification of controls, tell-tales and indicators) |
(a) The symbols including the colour of their corresponding tell-tales the presence of which is mandatory by virtue of UN Regulation No 121 shall comply with that UN Regulation. (b) Where this is not the case, the technical service shall verify that the symbols, tell-tales and indicators fitted to the vehicle provide the driver with comprehensible information about the operation of the controls in question. |
|
34A |
Regulation (EU) No 672/2010 (Defrost/Demist) |
The vehicle shall be equipped with adequate windscreen defrosting and windscreen demisting devices. A windscreen defrosting device which complies as a minimum with point 1.1.1 of Annex II to Regulation (EU) No 672/2010 shall be deemed ‘adequate’. A windscreen demisting device which complies as a minimum with point 1.2.1 of Annex II to Regulation (EU) No 672/2010 shall be deemed ‘adequate’. |
|
35A |
Regulation (EU) No 1008/2010 (Wash/Wipe) |
The vehicle shall be equipped with adequate windscreen washing and windscreen wiping devices. A windscreen washing and wiping device that complies as a minimum with the conditions set out in point 1.1.5 of Annex III to Regulation (EU) No 1008/2010 shall be deemed ‘adequate’. |
|
36A |
UN Regulation No 122 (Heating systems) |
(a) The passenger compartment shall be fitted with a heating system. (b) Combustion heaters and their installation shall comply with Annex 7 to UN Regulation No 122. In addition, LPG combustion heaters and LPG heating systems shall fulfil the requirements set out in Annex 8 to UN Regulation No 122. (c) Additional heating systems which are retrofitted shall comply with the requirements set out in that UN Regulation No 122. |
|
37A |
Regulation (EU) No 1009/2010 (Wheel guards) |
(a) The vehicle shall be designed as to protect other road users against thrown-up stones, mud, ice, snow and water and to reduce the dangers due to contact with the moving wheels. (b) The technical service may check that the technical requirements set out in Annex II to Regulation (EU) No 1009/2010 are complied with. (c) Section 3 of Annex I to that Regulation shall not apply. |
|
38A |
UN Regulation No 25 (Head restraints) |
The requirements of UN Regulation No 25 shall not apply. |
|
44A |
Regulation (EU) No 1230/2012 (Masses and dimensions) |
(a) The requirements of point 1 of Part A of Annex I to Regulation (EU) No 1230/2012 shall be fulfilled. (b) For the purposes of point (a), the masses to be considered are the following: — the mass in running order defined in point (4) of Article 2 of Regulation (EU) No 1230/2012 as measured by the technical service; and — the laden masses either stated by the vehicle manufacturer or shown on the manufacturer's plate including stickers or information available in the owner's manual. Those masses shall be deemed the technically permissible maximum laden masses. (c) No exemption shall be permitted in respect of the maximum permissible dimensions. |
|
45A |
UN Regulation No 43 (Safety glazing) |
Components (a) The glazing shall be made either of tempered or laminated safety glass. (b) Fitting of plastic glazing shall be permitted only on locations situated behind the ‘B’ pillar. (c) Glazing shall not be required to be approved under UN Regulation No 43. Installation (a) The installation requirements set out in Annex 21 to UN Regulation No 43 shall apply. (b) No tinted films that would reduce the regular light transmission under the required minimum shall be permitted on the windscreen and on the glazing located in front of the ‘B’ pillar. |
|
46 |
Directive 92/23/EEC (Tyres) |
Components Tyres shall bear an ‘EC’ type-approval mark including the symbol ‘s’ (for sound). Installation (a) The dimensions, load-capacity index and speed category of the tyres shall fulfil the requirements of Annex IV to Directive 92/23/EEC. (b) The speed category symbol of the tyre shall be compatible with the maximum design speed of the vehicle. This requirement shall apply notwithstanding the presence of a speed limiter. (c) The maximum speed of the vehicle shall be stated by the vehicle manufacturer. However, the technical service may assess the maximum design speed of the vehicle by using the engine maximum power output, the maximum number of revolutions per minute and the data concerning the kinematic chain. |
|
50A |
UN Regulation No 55 (Couplings) |
Separate technical units (a) OEM couplings intended for towing a trailer whose maximum mass does not exceed 1 500 kg shall not be required to be type-approved under UN Regulation No 55. A coupling is deemed OEM equipment where it is described in the owner's manual or an equivalent supporting document provided to the buyer by the vehicle manufacturer. Where such coupling is approved with the vehicle, an appropriate text shall be included in the approval certificate stating that the owner is responsible for ensuring compatibility with the coupling device fitted to the trailer. (b) Couplings other than those referred to in point (a), as well as couplings that are retrofitted, shall be type-approved in accordance with UN Regulation No 55. Installation on the vehicle The technical service shall check that the installation of the coupling devices comply with paragraph 6 of UN Regulation No 55. |
|
53A |
UN Regulation No 94 (Frontal impact) (e) |
(a) The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, of which the VIN has to be specified, complies with at least one of the following: — UN Regulation No 94; — FMVSS No 208 (Occupant crash protection); — Article 18 of JSRRV. (b) A test in accordance with paragraph 5 of UN Regulation No 94 may be conducted on a production vehicle at the request of the applicant. The test shall be conducted by a technical service that has been designated for carrying out this test. A detailed report shall be issued by that technical service to the applicant. |
|
54A |
UN Regulation No 95 (Side impact) |
(a) The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, of which the VIN has to be specified complies with at least one of the following: — UN Regulation No 95; — FMVSS No 214 (Side impact protection); — Article 18 of JSRRV. (b) A test in accordance with section 5 of UN Regulation No 95 may be conducted on a production vehicle at the request of the applicant. The test shall be conducted by a technical service that has been designated for carrying out this test. A detailed report shall be issued by that technical service to the applicant. |
|
58 |
UN Regulation No 127 Regulation (EU) 2019/2144 (Pedestrian protection) |
Vehicles shall be fitted with an electronic antilock braking system acting on all wheels. The requirements of UN Regulation No 127 shall apply. Any frontal protection system shall either be an integral part of the vehicle and thus compliant with the requirements of UN Regulation No 127 or be type‐approved as separate technical unit. |
|
59 |
Directive 2005/64/EC (Recyclability) |
The requirements of that Directive shall not apply. |
|
61 |
Directive 2006/40/EC (Air-conditioning system) |
The requirements of that Directive shall apply. |
|
62 |
UN Regulation No 134 Regulation (EU) 2019/2144 (Hydrogen system) |
The requirements of UN Regulation No 134 shall apply. Alternatively, it shall be demonstrated that the vehicle complies with: — Substantive requirements of Regulation (EC) No 79/2009 in its version applicable on 5 July 2022; — Attachment 100 – Technical Standard For Fuel Systems Of Motor Vehicle Fueled By Compressed Hydrogen Gas (Japan); — GB/T 24549-2009 Fuel cell electric vehicles – safety requirements (China); — International standard ISO 23273:2013 Part 1: Vehicle functional safety and Part 2: Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen; or — SAE J2578 – General Fuel Cell Vehicle Safety |
|
72 |
Regulation (EU) 2015/758 (eCall system) |
The requirements of that Regulation shall not apply. |
|
(1)
Council Directive 70/157/EEC of 6 February 1970 on the approximation of the laws of the Member States relating to the permissible sound level and the exhaust system of motor vehicles (OJ L 42, 23.2.1970, p. 16). |
||
Part II Vehicles belonging to category N1
|
Item |
Regulatory act reference |
Alternative requirements |
|
2A |
Regulation (EC) No 715/2007 (Emissions (Euro 5 and Euro 6) light duty vehicles / access to information) |
Tailpipe emissions (a) A type 1 test shall be conducted in accordance with Annex III to Regulation (EC) No 692/2008 using the deterioration factors set out in point 1.4 of Annex VII to that Regulation. The emission limits to be applied shall be those specified in Table 1 and Table 2 of Annex I to Regulation (EC) No 715/2007. (b) The vehicle shall not be required to exhibit 3 000 km as mentioned in paragraph 3.1.1 of Annex 4 to UN Regulation No 83. (c) The fuel to be used for the test shall be the reference fuel as prescribed in Annex IX to Regulation (EC) No 692/2008. (d) The dynamometer shall be set up in accordance with the technical requirements of paragraph 3.2 of Annex 4 to UN Regulation No 83. (e) The test referred to in point (a) shall not be conducted where it can be shown that the vehicle complies with the California Code Regulations referred to in point 2 of Annex I to Regulation (EC) No 692/2008. Evaporative emissions For petrol-fuelled engines, the presence of an evaporate emissions control system (e.g. a charcoal canister) shall be required. Crankcase emissions The presence of a device for recycling crankcase gases shall be required. OBD The vehicle shall be fitted with an OBD system. OBD-interface must be able to communicate with common diagnostic tools used for periodic technical inspections. Smoke opacity (a) Vehicles equipped with a diesel-fuelled engine shall be tested in accordance with the tests methods referred to in Appendix 2 to Annex IV to Regulation (EC) No 692/2008. (b) The corrected value of the absorption coefficient shall be affixed, conspicuously and in a readily accessible place. CO2 emissions and fuel consumption (a) A test shall be conducted in accordance with Annex XII to Regulation (EC) No 692/2008. (b) The vehicle shall not be required to exhibit 3 000 km as requested in paragraph 3.1.1 of Annex 4 to UN Regulation No 83. (c) Where the vehicle complies with the California Code Regulations referred to in point 2.1.1 of Annex I to Commission Regulation (EC) No 692/2008 and therefore no test of tailpipe emissions is required to be performed, Member States shall calculate CO2 emissions and fuel consumption with the formula laid down in the explanatory notes (b) and (c). Access to information The provisions regarding access to information shall not apply. Power measurement (a) The applicant shall submit a statement from the manufacturer stating the maximum engine power output in kW as well as the corresponding regime in revolutions per minute. (b) An engine power output curve providing the same information may alternatively be provided by the applicant. |
|
3A |
UN Regulation No 34 (Fuel tanks — Rear protective devices) |
Fuel tanks (a) Fuel tanks shall comply with paragraph 5 of UN Regulation No 34 with the exception of paragraphs 5.1, 5.2 and 5.12. In particular, they shall comply with paragraph 5.9 and 5.9.1 but no dripping test shall be conducted. (b) LPG or CNG tanks shall be type-approved in accordance with, respectively UN Regulations No 67, series of amendments 01, or UN Regulation No 110 (a). Specific provisions for fuel tanks made of a plastic material The applicant shall submit a statement from the manufacturer establishing that the fuel tank on the particular vehicle, of which the VIN has to be specified, complies either with at least one of the following: — FMVSS No 301 (Fuel system integrity); — Annex 5 to UN Regulation No 34. Rear protective device (a) The rear part of the vehicle shall be constructed in accordance with paragraphs 8 and 9 of UN Regulation No 34. |
|
4A |
Regulation (EU) No 1003/2010 (Rear registration plate space) |
Space, inclination, angles for visibility and position of the registration plate shall comply with Regulation (EU) No 1003/2010. |
|
5A |
UN Regulation No 79 (Steering effort) |
Mechanical systems (a) The steering mechanism shall be built as to self-centre. In order to check compliance with this provision, a test shall be conducted in accordance with paragraphs 6.1.2 and 6.2.1 of UN Regulation No 79. (b) The failure of the power steering equipment shall not lead to a complete loss of control of the vehicle. Complex electronic vehicle control system (‘Drive-by wire’ devices) Complex electronic control system shall be permitted only if they comply with Annex 6 to UN Regulation No 79. |
|
6A |
UN Regulation No 11 (Door latches and hinges) |
Compliance with paragraph 6.1.5.4 of UN Regulation No 11 |
|
7A |
UN Regulation No 28 (Audible warning) |
Components The audible warning devices are not required to be type-approved in accordance with UN Regulation No 28. However, they shall emit a continuous sound as required in paragraph 6.1.1 of UN Regulation No 28. Installation on vehicle (a) A test shall be conducted in accordance with paragraph 6.2 of UN Regulation No 28. (b) The maximum sound pressure level shall be in accordance with paragraph 6.2.7. |
|
8A |
UN Regulation No 46 (Indirect vision devices) |
Components (a) The vehicle shall be fitted with the rear-view mirrors prescribed in paragraph 15.2 of UN Regulation No 46. (b) They are not required to be type-approved in accordance with UN Regulation No 46. (c) The radii of curvature of the mirrors shall not cause significant image distortions. At the discretion of the technical service, the radii of curvature shall be checked in accordance with the method described in Appendix 1 to Annex 7 to UN Regulation No 46. The radii of curvature shall not be less than those required by paragraph 6.1.2.2.4 of UN Regulation No 46. Installation on vehicle Measurement shall be conducted in order to ensure that the fields of vision comply with paragraph 15.2.4 of UN Regulation No 46. |
|
9B |
UN Regulation No 13-H (Braking) |
General provisions (a) The braking system shall be built in accordance with paragraph 5 of UN Regulation No 13-H. (b) Vehicles shall be fitted with an electronic antilock braking system acting on all wheels. (c) The performances of the braking system shall comply with Annex III to UN Regulation No 13-H. (d) For these purposes, road tests shall be conducted on a track the surface of which possesses high adhesion. The test on the parking brake shall be conducted on a 18 % gradient (up and down). Only those tests mentioned under the headings ‘Service brake’ and ‘Parking brake’ below shall be conducted. In each case, the vehicle shall be in fully laden conditions. (e) The road test referred to in point (c) shall not be conducted where the applicant can submit a statement from the manufacturer establishing that the vehicle complies either with UN Regulation No 13-H including supplement 5 or with FMVSS No 135. Service brake (a) A ‘Type 0’ test as prescribed in paragraphs 1.4.2 and 1.4.3 of Annex 3 to UN Regulation No 13-H shall be conducted. (b) In addition, a ‘Type I’ test as prescribed in paragraph 1.5 of Annex 3 to UN Regulation No 13-H shall be conducted. Parking brake A test shall be conducted in accordance with paragraph 2.3 of Annex 3 to UN Regulation No 13-H. |
|
10A |
UN Regulation No 10 (Radio interference (electromagnetic compatibility)) |
Components (a) Electrical/electronic sub-assemblies are not required to be type-approved in accordance with UN Regulation No 10. (b) However, electric/electronic devices retrofitted shall comply with UN Regulation No 10. Emitted electromagnetic radiations The applicant shall submit a statement from the manufacturer establishing that the vehicle complies with UN Regulation No 10 or with the following alternative standards: — Broadband electromagnetic radiation: CISPR 12 or SAE J551-2; — Narrowband electromagnetic radiation: CISPR 12 (off-board) or 25 (in-board) or SAE J551-4 and SAE J1113-41. Immunity tests Immunity test shall be waived. |
|
13B |
UN Regulation No 116 (Anti-theft and immobiliser) |
(a) In order to prevent unauthorised use, the vehicle shall be fitted with a locking device as defined in paragraph 5.1.2 of UN Regulation No 116. (b) If an immobiliser is fitted, it shall comply with the technical requirements of paragraph 8.1.1 of UN Regulation No 116. |
|
14A |
UN Regulation No 12 (Protective steering) |
(a) The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, the VIN of which has to be specified, complies with at least one of the following: — UN Regulation No 12; — FMVSS No 203 (Impact protection for the driver from the steering control system) including FMVSS No 204 (Steering control rearward displacement); — Article 11 of JSRRV. (b) A test in accordance with Annex 3 to UN Regulation No 12 may be conducted on a production vehicle at the request of the applicant. The test shall be conducted by a technical service that has been designated for carrying out this test. A detailed report shall be issued by that technical service to the applicant. |
|
15A |
UN Regulation No 17 (Seats strength — head restraints) |
Seats, seat anchorages and adjustment systems Seats and their adjustable systems shall comply with paragraph 5.3 of UN Regulation No 17. Head restraints (a) Head restraints shall fulfil the requirements of section 5 of UN Regulation No 17 and Annex 4 to UN Regulation No 17. (b) Only the tests described in paragraphs 5.12, 6.5, 6.6 and 6.7 of UN Regulation No 17 shall be conducted. |
|
17A |
UN Regulation No 39 (Speedometer — reverse gear) |
Speedometer equipment (a) The dial shall comply with paragraphs 5.1 to 5.1.4 of UN Regulation No 39. (b) When the technical service has reasonable grounds to believe that the speedometer is not calibrated with a sufficient accuracy, it may require that the tests prescribed in paragraph 5.2 of UN Regulation No 39 be conducted. Reverse gear The gear mechanism shall include a reverse gear. |
|
18A |
Regulation (EU) No 19/2011 (Statutory plates) |
VIN (a) The vehicle shall be fitted with a VIN comprising a minimum of 8 and a maximum of 17 characters. VIN comprising 17 characters shall fulfil the requirements set out in international standards ISO 3779:1983 and 3780:1983. (b) The VIN shall be located in a clearly visible and accessible position in such a way as it cannot be obliterated or deteriorate. (c) Where no VIN is stamped in the chassis or in the body, a Member State may require that it is retrofitted in application of its national law. In such a case, the competent authority of that Member State shall supervise the operation. Statutory plate The vehicle shall be fitted with an identification plate affixed by the vehicle manufacturer. No additional plate shall be requested after the approval has been granted. |
|
19A |
UN Regulation No 14 (Seat belt anchorages) |
The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, of which the VIN has to be specified, complies with at least one of the following: — UN Regulation No 14; — FMVSS No 210 (Seat belt assembly anchorages); — Article 22-3 of JSRRV. |
|
20A |
UN Regulation No 48 (Installation of lighting and light signalling devices) |
(a) The lighting installation shall meet the essential requirements of UN Regulation No 48 series of amendments 03 with the exception of those of Annexes 5 and 6 to UN Regulation No 48. (b) No exemption shall be permitted in respect of the number, the essential design characteristics, the electrical connections, and the colour of light emitted or retro-reflected of the lights and signalling devices referred to in items 21 to 26 and in items 28 to 30. (c) Lights and signalling devices that, for the purpose of fulfilling with the requirements of point (a) must be retrofitted shall bear an ‘EU’ type-approval mark. (d) Lamps fitted with gas-discharged light source are only permitted in conjunction with the installation of headlamp cleaning device and an automatic headlamp-levelling device where appropriate. (e) Headlamp dipped-beams shall be adapted to the direction of traffic legally in force in the country where the vehicle is granted approval. |
|
21A |
UN Regulation No 3 (Retro reflectors) |
Where necessary, two additional retro reflectors bearing an ‘EC’ approval mark shall be added at the rear, the position of which shall comply with UN Regulation No 48. |
|
22A |
UN Regulations No 7, No 87 and No 91 (End-outline, front position (side), rear-position (side), stop, side marker, daytime running lamps) |
The requirements set out in UN Regulations No 7, No 87 and No 91 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
23A |
UN Regulation No 6 (Direction indicators) |
The requirements set out in UN Regulation No 6 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
24A |
UN Regulation No 4 (Rear registration plate lamps) |
The requirements set out in UN Regulation No 4 shall not apply. However, the correct functioning of the lights shall be checked by the technical service. |
|
25C, 25E, 25F |
UN Regulations No 98, No 112 and No 123 (Headlamps (including bulbs)) |
(a) The illumination produced by the passing beam of the headlamps fitted to the vehicle shall be checked under the provisions of paragraph 6 of UN Regulation No 112 concerning headlamps emitting an asymmetrical passing beam. The tolerances included in Annex 5 to that Regulation may be referred to for that purpose. (b) The same requirement shall apply to the passing beam of headlamps covered by UN Regulation No 98 or No 123. |
|
26A |
UN Regulation No 19 (Front fog lamps) |
The provisions of UN Regulation No 19 shall be waived. However, the correct functioning of the lights if fitted shall be checked by the technical service. |
|
27A |
Regulation (EU) No 1005/2010 (Towing hooks) |
The requirements of Regulation (EU) No 1005/2010 shall be waived. |
|
28A |
UN Regulation No 38 (Rear fog lamps) |
The provisions of UN Regulation No 38 shall be waived. However, the correct functioning of the lights shall be checked by the technical service. |
|
29A |
UN Regulation No 23 (Reversing lamps) |
The provisions of UN Regulation No 23 shall be waived. However, the correct functioning of the lights if fitted shall be checked by the technical service. |
|
30A |
UN Regulation No 77 (Parking lamps) |
The provisions of UN Regulation No 77 shall be waived. However, the correct functioning of the lights if fitted shall be checked by the technical service. |
|
31A |
UN Regulation No 16 (Seat belts and restraint systems) |
Components (a) Seat belts shall not be required to be type-approved in accordance with UN Regulation No 16. (b) However, each seat belt shall bear an identification label. (c) The indications on the label shall be consistent with the decision concerning seat belt anchorages (Re: entry 19). Installation requirements (a) The vehicle shall be fitted with seat belts in accordance with the requirements set out in Annex XVI to UN Regulation No 16. (b) Where a number of seat belts have to be retrofitted in accordance with point (a), they shall be of an approved type in accordance with UN Regulation No 16. |
|
33A |
UN Regulation No 121 (Identification of controls, tell-tales and indicators) |
(a) The symbols including the colour of their corresponding tell-tales the presence of which is mandatory by virtue of UN Regulation No 121 shall comply with that UN Regulation. (b) Where this is not the case, the technical service shall verify that the symbols, tell-tales and indicators fitted to the vehicle provide the driver with comprehensible information about the operation of the controls in question. |
|
34A |
Regulation (EU) No 672/2010 (Defrost/Demist) |
The vehicle shall be equipped with adequate windscreen defrosting and windscreen demisting devices. |
|
35A |
Regulation (EU) No 1008/2010 (Wash/Wipe) |
The vehicle shall be equipped with adequate windscreen washing and windscreen wiping devices. |
|
36A |
UN Regulation No 122 (Heating systems) |
(a) The passenger compartment shall be fitted with a heating system. (b) Combustion heaters and their installation shall comply with Annex 7 to UN Regulation No 122. In addition, LPG combustion heaters and LPG heating systems shall fulfil the requirements set out in Annex 8 to UN Regulation No 122. (c) Additional heating systems that are retrofitted shall comply with the requirements set out in UN Regulation No 122. |
|
41A |
Regulation (EC) No 595/2009 (Emissions (Euro VI) heavy-duty vehicles – OBD) |
Tailpipe emissions (a) A test shall be conducted in accordance with Annex III to Commission Regulation (EU) No 582/2011 (1) using the deterioration factors set out in point 3.6.1 of Annex VI to Regulation (EU) No 582/2011. (b) The limits to be applied shall be those set out in the table of Annex I to Regulation (EC) No 595/2009. (c) The fuel to be used for the test shall be the reference fuel as prescribed in Annex IX to Regulation (EU) No 582/2011. CO2 emissions The CO2 emissions and fuel consumption shall be determined in accordance with Annex VIII to Regulation (EU) No 582/2011. OBD (a) The vehicle shall be fitted with an OBD system. (b) The OBD-interface must be able to communicate with an external OBD scan-tool as described in Annex X to Regulation (EU) No 582/2011. Requirements to ensure the correct operation of NOx control measures The vehicle shall be fitted with a system ensuring the correct operation of NOx control measures in accordance with Annex XIII to Regulation (EU) No 582/2011. Power measurement (a) The applicant shall submit a statement from the manufacturer stating the maximum engine power output in Kw as well as the corresponding regime. (b) An engine power output curve providing the same information may alternatively be provided by the applicant. |
|
45A |
UN Regulation No 43 |
Components (a) The glazing shall be made either of tempered or laminated safety glass. (b) Fitting of plastic glazing shall be permitted only on locations situated behind the ‘B’ pillar. (c) Glazing shall not be required to be approved under UN Regulation No 43. Installation (a) The installation requirements set out in Annex 21 to UN Regulation No 43 shall apply. (b) No tinted films that reduce the regular light transmission under the required minimum shall be permitted on the windscreen and on the glazing located in front of the ‘B’ pillar. |
|
46A |
Commission Regulation (EU) 458/2011 (Installation of tyres) |
Installation (a) The dimensions, load-capacity index and speed category of the tyres shall fulfil the requirements of Commission Regulation (EU) 458/2011. (b) The speed category symbol of the tyre shall be compatible with the maximum design speed of the vehicle. (c) This requirement shall apply notwithstanding the presence of a speed limiter. (d) The maximum speed of the vehicle shall be stated by the vehicle manufacturer. However, the technical service may assess the maximum design speed of the vehicle by using the engine maximum power output, the maximum number of revolutions per minute and the data concerning the kinematic chain. |
|
46B |
UN Regulation No 30 (C1 tyres) |
Components Tyres shall bear a type-approval mark. |
|
46D |
UN Regulation No 117 (Tyre rolling sound emissions, adhesion on wet surface and rolling resistance) |
Components Tyres shall bear a type-approval mark. |
|
46E |
►M1 Regulation (EU) 2019/2144 ◄ UN Regulation No 64 (Temporary use spare unit, run-flat tyres, tyre rolling sound emissions, adhesion on wet surface and rolling resistance) |
Components Tyres shall bear type-approval mark. The fitting of TPMS shall not be required. |
|
48A |
Regulation (EU) No 1230/2012 (Masses and dimensions) |
(a) The requirements of Annex I, Part A to Regulation (EU) No 1230/2012 shall be fulfilled. However, the requirements set out in point 5 of Part A of Annex I do not need to be fulfilled. (b) For the purposes of point (a) the masses to be considered are the following: — the mass in running order as defined in point (4) of Article 2 of Regulation (EU) No 1230/2012 as measured by the technical service; and — the maximum laden masses either stated by the vehicle manufacturer or shown on the manufacturer's plate, including stickers or information available in the owner's manual. Those masses shall be regarded as the technically permissible maximum laden masses. (c) Technical changes made by the applicant in order to decrease the maximum technically permissible laden mass of the vehicle to 3,5 tonnes or less, so that the vehicle may be granted individual vehicle approval shall not be permitted. (d) No exemption shall be permitted in respect of the maximum permissible dimensions. |
|
49A |
UN Regulation No 61 (External projections of cabs) |
(a) The general requirements set out in section 5 of UN Regulation No 17 shall be fulfilled. (b) At the discretion of the technical service, the requirements set out in paragraphs 6.1, 6.5, 6.6, 6.7, 6.8 and 6.11 of UN Regulation No 17 shall be fulfilled. |
|
50A |
UN Regulation No 55 (Couplings) |
Separate technical units (a) OEM couplings intended for towing a trailer of which the maximum mass does not exceed 1 500 kg shall not be required to be type-approved under UN Regulation No 55. (b) A coupling is deemed OEM equipment where it is described in the owner's manual or in an equivalent supporting document provided to the buyer by the vehicle manufacturer. (c) Where such coupling is approved with the vehicle, an appropriate text shall be included in the approval certificate stating that the owner is responsible for ensuring compatibility with the coupling device fitted to the trailer. (d) Couplings other than those referred to in point (a), as well as couplings that are retrofitted, shall be type-approved in accordance with UN Regulation No 55. Installation on the vehicle The technical service shall check that the installation of the coupling devices comply with paragraph 6 to UN Regulation No 55. |
|
54 |
UN Regulation No 95 (Side impact) |
(a) The applicant shall submit a statement from the manufacturer establishing that the particular vehicle, of which the VIN has to be specified, complies with at least one of the following: — UN Regulation No 95; — FMVSS No 214 (Side impact protection); — Article 18 of JSRRV. (b) A test in accordance with section 5 of UN Regulation No 95 may be conducted on a production vehicle at the request of the applicant. (c) The test shall be conducted by a technical service that been designated for carrying out this test. A detailed report shall be issued by that technical service to the applicant. |
|
56A |
UN Regulation No 105 (Vehicles intended for the transport of dangerous goods) |
Vehicles intended for the transport of dangerous goods shall comply with UN Regulation No 105. |
|
58 |
UN Regulation No 127 Regulation (EU) 2019/2144 (Pedestrian protection) |
Vehicles shall be fitted with an electronic antilock braking system acting on all wheels. The requirements of UN Regulation No 127 shall apply. Any frontal protection system shall either be an integral part of the vehicle and thus compliant with the requirements of UN Regulation No 127 or be type‐approved as separate technical unit |
|
59 |
Directive 2005/64/EC (Recyclability) |
The requirements of that Directive shall not apply. |
|
61 |
Directive 2006/40/EC (Air-conditioning system) |
The requirements of that Directive shall apply. |
|
62 |
UN Regulation No 134 Regulation (EU) 2019/2144 (Hydrogen system) |
The requirements of UN Regulation No 134 shall apply. Alternatively, it shall be demonstrated that the vehicle complies with: — Substantive requirements of Regulation (EC) No 79/2009 in its version applicable on 5 July 2022; — Attachment 100 – Technical Standard For Fuel Systems Of Motor Vehicle Fueled By Compressed Hydrogen Gas (Japan); — GB/T 24549-2009 Fuel cell electric vehicles – safety requirements (China); — International standard ISO 23273:2013 Part 1: Vehicle functional safety and Part 2: Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen; or — SAE J2578 – General Fuel Cell Vehicle Safety |
|
72 |
Regulation (EU) 2015/758 (eCall system) |
The requirements of that Regulation shall not apply. |
|
(1)
Commission Regulation (EU) No 582/2011 of 25 May 2011 implementing and amending Regulation (EC) No 595/2009 of the European Parliament and of the Council with respect to emissions from heavy duty vehicles (Euro VI) and amending Annexes I and III to Directive 2007/46/EC of the European Parliament and of the Council (OJ L 167, 25.6.2011, p. 1). |
||
Explanatory notes to Appendix 2
1. Abbreviations used in this Appendix:
‘OEM’ : original equipment provided by the manufacturer
‘FMVSS’ : Federal Motor Vehicle Safety Standard of the U.S. Department of Transportation
‘JSRRV’ : Japan Safety Regulations for Road Vehicles
‘SAE’ : Society of Automotive Engineers
‘CISPR’ : Comité international spécial des perturbations radioélectriques.
2. Remarks:
the complete LPG or CNG installation shall be checked against the UN Regulations No 67, No 110 or No 115, as appropriate;
the formula to be used for the assessment of CO2 emissions shall be as follows:
Where: CO2 is the combined mass of CO2 emissions in g/km, ‘m’ is the mass of the vehicle in running order in kg and ‘p’ the maximum engine power output in kW.
Combined mass of CO2 shall be calculated with one decimal place, then rounded to the nearest whole number as follows:
if the figure following the decimal point is below 5, the total is rounded down;
if the figure following the decimal point is equal to 5 or above 5, the total is rounded up;
the formula to be used for the assessment of fuel consumption shall be as follows:
CFC = CO2 × k – 1
Where: CFC is the combined fuel consumption in l/100 km, CO2 is the combined mass of CO2 emissions in g/km after it has been rounded in accordance with the rule referred to in Remark (2 b), ‘k’ a coefficient equal to:
Combined fuel consumption shall be calculated with two decimal places, then rounded as follows:
if the figure following the first decimal is below 5, the total is rounded down;
if the figure following the first decimal is equal to 5 or above 5, the total is rounded up.
PART II
List of UN Regulations recognised as an alternative to the Directives or Regulations referred to in Part I
Where reference is made to a separate Directive or Regulation in the table of Part I, a type-approval issued under the following UN regulations, or a Universal International Whole Vehicle Type Approval issued under UN Regulation No 0 ( 13 ) that includes type-approval of the relevant item under the following UN Regulations, to which the Union has acceded as a Contracting Party to the United Nations Economic Commission for Europe ‘Revised 1958 Agreement’ by virtue of Council Decision 97/836/EC ( 14 ), or subsequent Council decisions as referred to in Article 3(3) of that Decision, shall be considered equivalent to an EU type-approval granted under the relevant separate Directive or Regulation.
Any further amendment to the UN Regulations listed in the following table ( 15 ) shall also be deemed to be equivalent to an EU type-approval, subject to the Decision referred to in Article 4(2) of Decision 97/836/EC.
Installation requirements laid down in a Directive or Regulation in the table of Part I shall apply also to components and separate technical units approved in accordance with the UN Regulations listed in the following table.
|
Item |
Subject |
UN Regulation |
Series of amendments |
|
B14 |
Acoustic vehicle alerting system |
138 |
01 |
|
G1 |
Sound level |
51 59 |
03 01 |
|
G13 |
Recyclability (1) |
133 |
00 |
|
(1)
The requirements set out in Annex I to Directive 2005/64/EC shall apply. |
|||
PART III
List of regulatory acts setting out the requirements for the purpose of EU type-approval of special purpose vehicles
EXPLANATORY NOTES
to the tables in Appendices 1 to 6
|
X |
: |
Compliance with the regulatory act is required according to the vehicle category for which type-approval is sought. Any specific provisions noted in addition to this explanatory note shall be taken into account. |
|
G |
: |
In case of multi-stage approval, compliance with the regulatory act according to which the base vehicle (e.g. the chassis of which was used to build the special purpose vehicle) has been type-approved shall be accepted. In this case, any vehicle systems, their features, parts, equipment, components and separate technical units that have been modified or added by the manufacturer, may be assessed against the base vehicle’s requirements. Any specific provisions noted in addition to this explanatory note shall be taken into account. |
|
A |
: |
The approval authority may agree to fully or partly grant exemptions upon the condition that the manufacturer demonstrates to the satisfaction of the technical service that the vehicle cannot meet the full set of requirements due to its special purpose. The manufacturer shall however endeavour to meet the requirements to the largest possible extent taking into account proportionality. Those exemptions shall be described in Part 2 of the vehicle EU type-approval certificate as well as under ‘remarks’ in the Certificate of Conformity. Any specific provisions noted in addition to this explanatory note shall be taken into account. |
Appendix 1
Motor-caravans, ambulances and hearses
|
Item |
Subject |
Regulatory act |
M1 ≤ 2 500 kg |
M1 > 2 500 kg |
M2 |
M3 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
|||||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
G Application is limited to the passenger compartment in front of the transverse plane passing through the torso reference line of the 3-D H machine placed on the rearmost seat designated for normal use when the vehicle is used on a public road, as well as to the respective reference zones of each seating position designated for normal use as defined in the regulatory act when the vehicle type is subject to the requirements applicable to vehicle category M1. It does not apply to the patient compartment of ambulances Additional requirements for new types of ambulances: The patient compartment of ambulances shall comply with the requirements of EN 1789:2020 on Medical vehicles and their equipment – Road ambulances with the exception of Section 6.5, list of equipment. Proof of compliance shall be provided with a test report of the technical service and may be based on an assessment carried out by subcontractors or subsidiaries of the technical service in accordance with the provisions of Article 71. If a wheelchair space is foreseen, the requirements for wheelchair accessible vehicles (code SH) relating to the wheelchair tie-down and occupant restraint systems shall also apply. |
G Application is limited to the passenger compartment in front of the transverse plane passing through the torso reference line of the 3-D H machine placed on the rearmost seat designated for normal use when the vehicle is used on a public road, as well as to the respective reference zones of each seating position designated for normal use as defined in the regulatory act when the vehicle type is subject to the requirements applicable to vehicle category M1. It does not apply to the patient compartment of ambulances Additional requirements for new types of ambulances: The patient compartment of ambulances shall comply with the requirements of EN 1789:2020 on Medical vehicles and their equipment – Road ambulances with the exception of Section 6.5, list of equipment. Proof of compliance shall be provided with a test report of the technical service and may be based on an assessment carried out by subcontractors or subsidiaries of the technical service in accordance with the provisions of Article 71. If a wheelchair space is foreseen, the requirements for wheelchair accessible vehicles (code SH) relating to the wheelchair tie-down and occupant restraint systems shall also apply. |
n/a for the passenger or patient compartment Additional requirements for new types of ambulances: The patient compartment of ambulances shall comply with the requirements of EN 1789:2020 on Medical vehicles and their equipment – Road ambulances with the exception of Section 6.5, list of equipment. Proof of compliance shall be provided with a test report of the technical service and may be based on an assessment carried out by subcontractors or subsidiaries of the technical service in accordance with the provisions of Article 71. If a wheelchair space is foreseen, the requirements for wheelchair accessible vehicles (code SH) relating to the wheelchair tie-down and occupant restraint systems shall also apply. |
n/a for the passenger or patient compartment Additional requirements for new types of ambulances: The patient compartment of ambulances shall comply with the requirements of EN 1789:2020 on Medical vehicles and their equipment – Road ambulances with the exception of Section 6.5, list of equipment. Proof of compliance shall be provided with a test report of the technical service and may be based on an assessment carried out by subcontractors or subsidiaries of the technical service in accordance with the provisions of Article 71. If a wheelchair space is foreseen, the requirements for wheelchair accessible vehicles (code SH) relating to the wheelchair tie-down and occupant restraint systems shall also apply. |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
G Application is limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. The energy dissipation and radii requirements are checked in accordance with paragraphs 5.2.3./5.2.4.2. and 5.2.4. of UN Regulation No 17 when the vehicle type is subject to the requirements applicable to vehicle category M1. The luggage retention requirements of UN Regulation No 17 (para. 1, point (c) and Annex 9) do not apply. |
G Application is limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. The energy dissipation and radii requirements are checked in accordance with paragraphs 5.2.3./5.2.4.2. and 5.2.4. of UN Regulation No 17 when the vehicle type is subject to the requirements applicable to vehicle category M1. The luggage retention requirements of UN Regulation No 17 (para. 1, point (c) and Annex 9) do not apply. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
G Application limited to seats designated for normal use when the vehicle is used on a public road. At least anchorages for lap belts are required in the rear seating positions. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. At least anchorages for lap belts are required in the rear seating positions. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. At least anchorages for lap belts are required in the rear seating positions. |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
G Application limited to seats designated for normal use when the vehicle is used on a public road. At least lap belts are required in the rear seating positions. |
G Application limited to seats designated for normal use when the vehicle is used on a public road. At least lap belts are required in the rear seating positions. |
G Application limited to seats designated for normal use when the vehicle is used on a public road. At least lap belts are required in the rear seating positions. |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
X Not required for rear seats |
X Not required for rear seats |
X Not required for rear seats |
X Not required for rear seats |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
equipment |
Equipment |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
G ISOFIX is not required on ambulances and hearses |
G ISOFIX is not required on ambulances and hearses |
IF |
IF |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
Equipment |
equipment |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
Equipment |
equipment |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
G |
G |
X |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
G |
G |
X |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
X |
G |
G |
X |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
X |
G |
X |
X |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
X |
G Completed vehicles are deemed to comply with the frontal off-set impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, irrespective of the mass in running order increase, as part of a previous-stage type-approval and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. Completed vehicles on the basis of a type-approved incomplete chassis-cowl configuration are exempted from the full-scale crash test. However, it shall be demonstrated to the satisfaction of the technical service that there is no unacceptable risk of fuel system integrity failure or unacceptable risk of direct contact with live parts of high voltage propulsion systems, after a frontal impact. Virtual testing methods may be used in accordance with Annex VIII to Regulation (EU) 2018/858. |
not in scope |
not in scope |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
G |
G Completed vehicles are deemed to comply with the frontal full-width impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, irrespective of the mass in running order increase, as part of a previous-stage type-approval and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service. Completed vehicles on the basis of a type-approved incomplete chassis-cowl configuration are exempted from the full-scale crash test. However, it shall be demonstrated to the satisfaction of the technical service that there is no unacceptable risk of fuel system integrity failure or unacceptable risk of direct contact with live parts of high voltage propulsion systems, after a frontal impact. Virtual testing methods may be used in accordance with Annex VIII to Regulation (EU) 2018/858.. |
not in scope |
not in scope |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
X |
G Completed vehicles are deemed to comply with the side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, irrespective of the mass in running order increase, as part of a previous-stage type-approval. Completed vehicles on the basis of a type-approved incomplete chassis-cowl configuration are exempted from the full-scale crash test. However, it shall be demonstrated to the satisfaction of the technical service that there is no unacceptable risk of fuel system integrity failure or unacceptable risk of direct contact with live parts of high voltage propulsion systems, after a side impact. Virtual testing methods may be used in accordance with Annex VIII to Regulation (EU) 2018/858. |
not in scope |
not in scope |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
n/a |
n/a |
not in scope |
not in scope |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
X |
G Completed vehicles are deemed to comply with rear impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase |
not in scope |
not in scope |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
G |
G |
not in scope |
not in scope |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
|||||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
X |
G Modifications to the interior fittings directly behind the windscreen do not have to be taken into account. |
not in scope |
not in scope |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
no requirements yet |
no requirements yet |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
G |
G |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
G |
G |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
X |
G |
G |
G |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
X |
X |
X |
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
|||||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
X |
G |
G |
G |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
n/a |
n/a |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
X |
G May be a C2 Lane departure warning system in case this was applicable for the base vehicle. |
not in scope |
not in scope |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
G |
G |
G |
G |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
X |
G In the case of modifications to the stability control system, included as part of a previous stage type-approval, that are likely to affect the function of that base vehicle’s stability control system, it shall be demonstrated that the vehicle has not been rendered unsafe or unstable. This shall be proven by tests e.g. performing rapid double lane-change manoeuvres in each direction at 80 km/h with sufficient severity to cause intervention by the stability control system. These interventions shall be well-controlled and shall improve the stability of the vehicle under those driving conditions in comparison to the stability of the vehicle with a disabled stability control system. All tests are subject to the agreement between the manufacturer and technical service. |
n/a |
n/a |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
n/a |
n/a |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
G |
G |
G |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
not in scope |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
X |
G |
not in scope |
not in scope |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
X |
G |
G |
G |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
|||||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
X |
G |
IF G |
IF G |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A + G for the cab A for the remaining part Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A + G for the cab A for the remaining part Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A + G for the cab A for the remaining part Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X |
X |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF |
IF |
IF |
IF |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
G |
G |
not in scope |
not in scope |
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
|||||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
IF |
not in scope |
not in scope |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
X |
G |
no requirement yet |
no requirement yet |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
IF |
no requirement yet |
no requirement yet |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
IF |
no requirement yet |
no requirement yet |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
|
|
|
|
|
|
|
|
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
|||||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
X Application limited to doors giving access to seats designated for normal use when the vehicle is used on a public road and where the distance between the R-point of the seat and the average plane of the door surface, measured perpendicular to the longitudinal medium plane of the vehicle, does not exceed 500 mm. |
G Application limited to doors giving access to seats designated for normal use when the vehicle is used on a public road and where the distance between the R-point of the seat and the average plane of the door surface, measured perpendicular to the longitudinal medium plane of the vehicle, does not exceed 500 mm. Completed vehicles on the basis of a type-approved incomplete chassis-cowl configuration are exempted from the general and performance requirements. |
not in scope |
not in scope |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
not in scope |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
G for the cab A for the remaining part The requirements on the protrusion of open windows do not apply to the living compartment |
G for the cab A for the remaining part The requirements on the protrusion of open windows do not apply to the living compartment |
not in scope |
not in scope |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
X Required for the front only, to be tested if fitted at the rear |
X Required for the front only, to be tested if fitted at the rear |
X Required for the front only, to be tested if fitted at the rear |
X Required for the front only, to be tested if fitted at the rear |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
G |
G |
not in scope |
not in scope |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
IF G |
IF G |
IF G |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A |
A |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A |
A |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
G for the cab X for the remaining part |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
|||||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. In the case of ambulances, an EU type-approval granted to the most representative base vehicle remains valid irrespective of a change in the reference weight. Motor-caravans and hearses: In the case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. It is allowed for the reference mass of the converted vehicle to exceed 2 840 kg. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. In the case of ambulances, an EU type-approval granted to the most representative base vehicle remains valid irrespective of a change in the reference weight. Motor-caravans and hearses: In the case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. It is allowed for the reference mass of the converted vehicle to exceed 2 840 kg. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. In the case of ambulances, an EU type-approval granted to the most representative base vehicle remains valid irrespective of a change in the reference weight. Motor-caravans and hearses: In the case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. It is allowed for the reference mass of the converted vehicle to exceed 2 840 kg. |
not in scope |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
G In the case of multi-stage type-approval, the new CO2 value shall be calculated in accordance with the CO2 interpolation method, using the relevant data from the completed vehicle. Alternatively, the new CO2 value shall be calculated on the basis of the parameters of the completed vehicle as specified in paragraph 3.2.4 of Annex B7 to UN Regulation 154 and using the road load matrix tool supplied by the manufacturer of the base vehicle. If the tool is not available or CO2 interpolation is impractical, the CO2 value of Vehicle High from the base vehicle shall be used, at the request of the manufacturer responsible for the conversion, and with the agreement of the approval authority. |
G In the case of multi-stage type-approval, the new CO2 value shall be calculated in accordance with the CO2 interpolation method, using the relevant data from the completed vehicle. Alternatively, the new CO2 value shall be calculated on the basis of the parameters of the completed vehicle as specified in paragraph 3.2.4 of Annex B7 to UN Regulation 154 and using the road load matrix tool supplied by the manufacturer of the base vehicle. If the tool is not available or CO2 interpolation is impractical, the CO2 value of Vehicle High from the base vehicle shall be used, at the request of the manufacturer responsible for the conversion, and with the agreement of the approval authority. |
G In the case of multi-stage type-approval, the new CO2 value shall be calculated in accordance with the CO2 interpolation method, using the relevant data from the completed vehicle. Alternatively, the new CO2 value shall be calculated on the basis of the parameters of the completed vehicle as specified in paragraph 3.2.4 of Annex B7 to UN Regulation 154 and using the road load matrix tool supplied by the manufacturer of the base vehicle. If the tool is not available or CO2 interpolation is impractical, the CO2 value of Vehicle High from the base vehicle shall be used, at the request of the manufacturer responsible for the conversion, and with the agreement of the approval authority. |
Not in scope |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
not in scope |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. In the case of ambulances, an EU type-approval granted to the most representative base vehicle remains valid irrespective of a change in the reference weight. Motor-caravans and hearses: In the case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. It is allowed for the reference mass of the converted vehicle to exceed 2 840 kg. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. In the case of ambulances, an EU type-approval granted to the most representative base vehicle remains valid irrespective of a change in the reference weight. Motor-caravans and hearses: In the case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. It is allowed for the reference mass of the converted vehicle to exceed 2 840 kg. |
G |
G |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
G |
G |
G |
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
G |
G |
G |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
G |
G |
G |
not in scope |
|
G8 |
Low-temperaturetailpipe emissions in lab |
Regulation (EC) No 715/2007 |
G |
G |
G |
not in scope |
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
G |
G |
G |
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
G |
G |
G |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
G |
G |
G |
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
G |
G |
G |
|
G13 |
Recyclability |
Directive 2005/64/EC |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
not in scope |
not in scope |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
G |
G |
not in scope |
not in scope |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
|||||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
X |
X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858 UN Regulation No 156 |
X |
X |
X |
X |
Appendix 2
Armoured vehicles
|
Item |
Subject |
Regulatory act |
M1 |
M2 |
M3 |
N1 |
N2 |
N3 |
O1 |
O2 |
O3 |
O4 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
|||||||||||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
not in scope |
not in scope |
not in scope |
not in scope |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
not in scope |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
A |
IF |
IF |
IF |
IF |
IF |
not in scope |
not in scope |
not in scope |
not in scope |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
A |
A |
X |
X |
X |
X |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
X |
X |
not in scope |
not in scope |
X |
X |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
n/a |
n/a |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
G |
not in scope |
not in scope |
G |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
|||||||||||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
not in scope |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
not in scope |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if the necessary devices cannot be placed in the optimal position as to prevent them from being damaged, which prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
G The light transmission factor is at least 60 % and the ‘A’ pillar obstruction angle is not more than 10 degrees. |
not in scope |
not in scope |
G The light transmission factor is at least 60 % and the ‘A’ pillar obstruction angle is not more than 10 degrees. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
not in scope |
no requirements yet |
no requirements yet |
not in scope |
no requirements yet |
no requirements yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
A |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
not in scope |
not in scope |
not in scope |
not in scope |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
A |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
not in scope |
not in scope |
not in scope |
not in scope |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
|||||||||||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
not in scope |
n/a |
n/a |
not in scope |
n/a |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
G |
G |
G |
G |
G |
G |
X |
X |
X |
X |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
X |
n/a |
n/a |
X |
n/a |
n/a |
not in scope |
not in scope |
X |
X |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
n/a |
n/a |
not in scope |
n/a |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
A |
not in scope |
not in scope |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
not in scope |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
n/a |
n/a |
not in scope |
n/a |
n/a |
not in scope |
not in scope |
n/a |
n/a |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
|||||||||||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
A Additional panic alarm devices are permitted |
A Additional panic alarm devices are permitted |
A Additional panic alarm devices are permitted |
A Additional panic alarm devices are permitted |
A Additional panic alarm devices are permitted |
A Additional panic alarm devices are permitted |
not in scope |
not in scope |
not in scope |
not in scope |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
X |
IF G |
IF G |
X |
IF G |
IF G |
not in scope |
not in scope |
not in scope |
not in scope |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
not in scope |
X |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
not in scope |
not in scope |
not in scope |
not in scope |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF |
IF |
IF |
IF |
IF |
IF |
not in scope |
not in scope |
not in scope |
not in scope |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
G |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
|||||||||||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
not in the scope |
not in the scope |
IF |
not in the scope |
not in the scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
A |
no requirement yet |
no requirement yet |
A |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
|||||||||||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
X |
not in scope |
not in scope |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
X |
not in scope |
not in scope |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
G |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
X |
X |
X |
X |
X |
X |
X |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
IF X |
IF X |
IF X |
IF X |
IF X |
X |
X |
X |
X |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
X |
X |
X |
X |
X |
X |
X |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
not in scope |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
not in scope |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
|||||||||||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
not in scope |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
not in scope |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
X At the manufacturer’s request Regulation (EC) No 715/2007 may apply to vehicles with a reference mass exceeding 2 840 kg. The approval authority may only grant exemption(s) if the manufacturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted are to be described on the vehicle type-approval certificate and the certificate of conformity. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
X |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G8 |
Low-temperaturetailpipe emissions in lab |
Regulation (EC) No 715/2007 |
X |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G13 |
Recyclability |
Directive 2005/64/EC |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
not in scope |
not in scope |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
X |
not in scope |
not in scope |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
|||||||||||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858 UN Regulation No 156 |
X |
X |
X |
X |
X |
X |
X |
X |
|
|
Appendix 3
Wheelchair-accessible vehicles
|
Item |
Subject |
Regulatory act |
M1 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
G Note G may be applied to those fittings in the interior of the vehicle that are not significantly affected by the modification, however, any added or modified fittings in the interior shall comply with the requirements as applicable for vehicle category M1 Application is limited to the passenger compartment in front of the transverse plane passing through the torso reference line of the 3-D H-point machine placed on the rearmost seat designated for normal use when the vehicle is used on a public road, as well as to the respective reference zones of each seating position designated for normal use as defined in the regulatory act when the vehicle type is subject to the requirements applicable to vehicle category M1. |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
G Note G may be applied to seats and head restraints of the vehicle that are not significantly affected by the modification, however, any added or modified fittings concerning seats and head restraints shall comply with the requirements as applicable for vehicle category M1 The energy dissipation and radii requirements of seats and head restraints are checked in accordance with paragraphs 5.2.3/5.2.4.2. and 5.2.4. of UN Regulation No 17 when the vehicle type is subject to the requirements applicable to vehicle category M1. The longitudinal plane of the intended wheelchair-travelling position shall be parallel to the longitudinal plane of the vehicle. Appropriate information is to be made available to the vehicle owner that, in order to withstand the forces transmitted by the tie-down mechanism during the various driving conditions, a wheelchair with a structure meeting the relevant part of ISO 7176-19:2008/Amd 1:2015 (or later revisions) is recommended. The seats of the vehicle may be adapted without further testing, provided it can be demonstrated to the satisfaction of the technical service that their anchorages, mechanisms and head restraints provide an adequate level of performance. The luggage retention requirements of UN Regulation No 17 (para. 1, point (c) and Annex 9) do not apply. |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
not in scope |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
X Each wheelchair location shall be provided with anchorages to which a wheelchair tie-down and occupant restraint system (WTORS) is to be fitted, and that complies with the additional provisions for testing the wheelchair tie down and occupant restraint system set out below. 1. Definitions 1.1. Surrogate wheelchair (SWC) means a rigid, re-usable test wheelchair, as defined in Section 3 of international standard ISO 10542-1:2012. 1.2. Point P means a representation of the position of the wheelchair occupant’s hip when seated in the SWC, as defined in Section 3 of international standard ISO 10542-1:2012. At the request of the manufacturer, a heavier surrogate wheelchair may be used, provided it has the same dimensional characteristics and centre of gravity position as the prescribed version. The pneumatic tyres may be replaced with solid or foam-filled versions in the same size. 1.3. WTORS means a wheelchair tie-down and occupant restraint system. 2. General requirements 2.1. Each wheelchair location shall be provided with anchorages to which a WTORS can be fitted. 2.2. The wheelchair occupant’s lower belt anchorages shall be located in accordance with paragraph 5.4.2.2 UN Regulation No 14, relative to Point P on the SWC, when placed in the travelling position designated by the manufacturer. The upper actual anchorage(s) shall be located at least 1 100 mm above the horizontal plane passing through the points of contact between the rear tyres of the SWC and the vehicle floor. That condition shall still be satisfied after the test carried out in accordance with points 3 or 4 below. Either point 3 or 4 shall apply. 3. Static in-vehicle testing 3.1. Wheelchair occupant restraint anchorages 3.1.1. The wheelchair occupant restraint anchorages shall resist the static forces prescribed for occupant restraint anchorages in UN Regulation No 14, simultaneously with the static forces applied to the wheelchair tie-down anchorages as specified in point 3.2. 3.2. Wheelchair tie-down anchorages The wheelchair tie-down anchorages shall resist the following forces, for at least 0,2 seconds, applied via the SWC (or a suitable surrogate wheelchair having a wheelbase, seat height and tie-down attachment points in accordance with the specification for the SWC), at a height of 300 +/– 100 mm from the surface on which the SWC rests: 3.2.1. In the case of a forward-facing wheelchair, a simultaneous force, coinciding with the force applied to the occupant restraint anchorages, of 24,5 kN; and 3.2.2. a second test applying a static force of 8,2 kN directed towards the rear of the vehicle. 3.2.3. In the case of a rearward-facing wheelchair, a simultaneous force, coincident with the force applied to the occupant restraint anchorages, of 8,2 kN, and 3.2.4. a second test applying a static force of 24,5 kN directed towards the front of the vehicle 4. Dynamic in-vehicle testing 4.1. The full assembly of the WTORS system shall be tested by an in-vehicle dynamic test in accordance with points 5.2.2 and 5.2.3 and Annex A to international standard ISO 10542-1:2012, testing all components/anchorages simultaneously, using a vehicle body-in-white or representative structure. |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
X Each wheelchair location is to be provided with an occupant restraint belt that complies with the additional provisions for testing the wheelchair tie down and occupant restraint system of set out below. When, due to the conversion, anchorage points for the safety belts need to be moved outside the tolerance provided for in paragraph 7.7.1 of UN Regulation No 16, the technical service shall check whether the alteration constitutes a worst-case or not. If that is the case, the test provided for in paragraph 7.7.1 of UN Regulation No 16 shall be performed. The test may be performed using components that have not undergone the conditioning test prescribed by UN Regulation No 16. 1. Definitions 1.1. Surrogate wheelchair (SWC) means a rigid, re-usable test wheelchair, as defined in Section 3 of international standard ISO 10542-1:2012. 1.2. Point P means a representation of the position of the wheelchair occupant’s hip when seated in the SWC, as defined in Section 3 of international standard ISO 10542-1:2012. At the request of the manufacturer, a heavier surrogate wheelchair may be used, provided it has the same dimensional characteristics and centre of gravity position as the prescribed version. The pneumatic tyres may be replaced with solid or foam-filled versions in the same size. 1.3. WTORS means a wheelchair tie-down and occupant restraint system. 2. General requirements 2.1. An assessment shall be made of the WTORS occupant belt to ensure compliance with paragraphs 8.2.2 to 8.2.2.4 and 8.3.1 to 8.3.4 of UN Regulation No 16. Either point 3. or 4. shall apply. 3. Static in-vehicle testing 3.1. Components of the system 3.1.1. Where the WTORS anchorages have been tested statically in the vehicle, all components of the WTORS shall meet the relevant requirements of international standard ISO 10542-1:2012. However, the dynamic test specified in Annex A to, and points 5.2.2. and 5.2.3. of, international standard ISO 10542-1:2012 shall be carried out on the complete WTORS using the vehicle anchorage geometry instead of the test geometry specified in Annex A to international standard ISO 10542-1:2012. This may be carried out within the vehicle structure or on a surrogate structure representative of the vehicle’s WTORS anchorage geometry. The location of each anchorage used for the test shall lie within the tolerance provided for in paragraph 7.7.1 of UN Regulation No 16, of its true position relative to Point P. 3.1.2. Where the occupant restraint part of the WTORS is approved in accordance with UN Regulation No 16, it shall be subject to the dynamic test as part of the complete WTORS specified in point 3.1.1., however, the requirements of points 5.1, 5.3 and 5.4 of international standard ISO10542-1:2012 shall be considered to have been met. 4. Dynamic in-vehicle testing 4.1. Where the WTORS anchorages have been tested dynamically in the vehicle, the component parts of the WTORS shall meet the relevant requirements of international standard ISO 10542-1:2012, points 5.1, 5.3 and 5.4. These requirements shall be deemed to have been met in respect of the occupant restraint if it is approved in accordance with UN Regulation No 16. |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
n/a |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
IF The minimum number of ISOFIX child seat anchorages need not to be provided. In the case of a multi-stage type approval where an ISOFIX anchorage system has been affected by the conversion, either the system shall be re-tested or the anchorages shall be rendered unusable. In the latter case the ISOFIX labels shall be removed and appropriate information shall be provided in the vehicle owner’s manual for the completed vehicle. |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
not in scope |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
X |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
not in scope |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
X Modification of the routing, length of the refuelling duct, fuel hoses and fuel vapour pipes as well as re-positioning of the original tank and evaporative control devices provided by the manufacturer of the base vehicle is permissible without further testing provided the installation requirements of paragraphs 5.4, 5.5, 5.6, 5.7, 5.8, and 5.11 of UN Regulation No 34 are met, and provided that the technical service is satisfied, by visual inspection, that the essential requirements of paragraph 5.10 of that Regulation have been satisfied. In cases involving re-positioning of the original plastic tank, further testing in accordance with Annex 5 to UN Regulation No 34 is not required. |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
G |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
G |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
G |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
G |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
G Alternatively, a suitable torsion stiffness test, in which a torque is applied to the vehicle as close as practicable to the spring mounting points, with all doors, hatches and bonnet opened, shall demonstrate that the torsional stiffness is within ± 75 % of that of the unmodified previous-stage vehicle body. In addition, a bending stiffness test shall be carried out with the vehicle on level ground, in which all side and rear doors and hatches shall open normally when the vehicle is loaded to its technically maximum permissible laden mass. |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
G Alternatively, a suitable torsion stiffness test, in which a torque is applied to the vehicle as close as practicable to the spring mounting points, with all doors, hatches and bonnet opened, shall demonstrate that the torsional stiffness is within ± 75 % of that of the unmodified previous-stage vehicle body. In addition, a bending stiffness test shall be carried out with the vehicle on level ground, in which all side and rear doors and hatches shall open normally when the vehicle is loaded to its technically maximum permissible laden mass. |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
G n/a in case of modified steering systems for drivers with special needs |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
not in scope |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
G Alternatively, a suitable torsion stiffness test, in which a torque is applied to the vehicle as close as practicable to the spring mounting points, with all doors, hatches and bonnet opened, shall demonstrate that the torsional stiffness is within ± 75 % of that of the unmodified previous-stage vehicle body. In addition, a bending stiffness test shall be carried out with the vehicle on level ground, in which all side and rear doors and hatches shall open normally when the vehicle is loaded to its technically maximum permissible laden mass. |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
n/a |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
n/a |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
G |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
G |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
G Modifications to the interior fittings directly behind the windscreen do not have to be taken into account. |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
G n/a in case of modified braking systems for drivers with special needs |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
not in scope |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
not in scope |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
A May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
G |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
not in scope |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
G |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
G |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
G |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
X |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
G |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
not in scope |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
G n/a in case of modified steering systems for drivers with special needs, or in case of modified braking system if the ELKS of the base vehicle acts on the braking system instead. |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
G |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
G n/a in case of modified braking systems for drivers with special needs |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
G In case of modifications to the stability control system included as part of a previous stage type-approval, which are likely to affect the function of that base vehicle’s stability control system, it shall be demonstrated that the vehicle has not been rendered unsafe or unstable. This shall be proven by tests e.g. performing rapid double lane-change manoeuvres in each direction at 80 km/h with sufficient severity to cause intervention by the stability control system. These interventions shall be well-controlled and shall improve the stability of the vehicle under those driving conditions in comparison to the stability of the vehicle with, where practicable, a disabled stability control system. All tests are subject to the agreement between the manufacturer and technical service. |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
G n/a in case of modified braking systems for drivers with special needs |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
X |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
G |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
X |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
X |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
not in scope |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
A May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
G |
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
A |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
A May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
No requirement yet |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
A May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
IF |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
No requirement yet |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
No requirement yet |
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
X |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
X |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
G Any boarding aids are considered only in the stowed position |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
not in scope |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
X Required for the front only, to be tested if fitted at the rear |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
G |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
not in scope |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
X For the purposes of calculations, the mass of the wheel-chair including the user is assumed to be 160 kg. The mass is concentrated at the P point of the surrogate wheelchair in its travelling position as declared by the manufacturer. It is permitted to temporarily limit the overall passenger capacity and to restrict the use of normal seating positions as a result of the actual transport of wheelchairs, with their users. In such case, the affected normal seating positions shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. This shall be noted in Part 2 of the EU type-approval certificate as well as under ‘remarks’ in the Certificate of Conformity as to allow inclusion of this information in on-board vehicle registration papers. In addition, the following shall be explained in the owner’s manual for the completed vehicle: The meaning of any pictograms used to mark the affected seating positions, as well as a more detailed description of the specific restrictions, if necessary. |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
not in scope |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
not in scope |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
not in scope |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
G Modification of the exhaust system length is permitted without the need for retesting, provided that the exhaust back pressure remains similar. |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
G Modification in the exhaust system is permitted without any further test of tailpipe emissions provided that the emission control devices, including particulate filters (if any), are not affected. In case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. In such a case it is acceptable if the reference mass of the converted vehicle will exceed 2 840 kg. |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
G Modification in the exhaust system is permitted without any further test of CO2/fuel consumption provided that the emission control devices, including particulate filters (if any), are not affected. In the case of multi-stage type-approval, the new CO2 value shall be calculated in accordance with the CO2 interpolation method, using the relevant data from the completed vehicle. Alternatively, the new CO2 value shall be calculated on the basis of the parameters of the completed vehicle as specified in paragraph 3.2.4 of Annex B7 to UN Regulation 154 and using the road load matrix tool supplied by the manufacturer of the base vehicle. If the tool is not available or CO2 interpolation is impractical, the CO2 value of Vehicle High from the base vehicle shall be used, at the request of the manufacturer responsible for the conversion, and with the agreement of the approval authority. |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
X Modification in the exhaust system is permitted without any further test of tailpipe emissions and CO2/fuel consumption provided that the emission control devices, including particulate filters (if any), are not affected. If the evaporative control devices are kept as fitted by the manufacturer of the original (complete or incomplete) vehicle, no new evaporative test is required on the modified vehicle. |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
Not in scope |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
Not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G In case of conversion of a vehicle (e.g. in a multi-stage type-approval process), the manufacturer responsible for the conversion needs to consult the original (complete or incomplete) vehicle manufacturer to get confirmation that the converted vehicle is covered by the emission approval of the original (complete or incomplete) vehicle. In such a case it is acceptable if the reference mass of the converted vehicle will exceed 2 840 kg. |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
G If the evaporative control devices are kept as fitted by the manufacturer of the original (complete or incomplete) vehicle, no new evaporative test is required on the modified vehicle. |
|
G8 |
Low-temperaturetailpipe emissions in lab |
Regulation (EC) No 715/2007 |
G |
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
G |
|
G13 |
Recyclability |
Directive 2005/64/EC |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
G |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858, Annex IV UN Regulation No 156 |
X |
Appendix 4
Other special purpose vehicles
(including special group, multi-equipment carrier and trailer caravans)
|
Item |
Subject |
Regulatory act |
M2 |
M3 |
N1 |
N2 |
N3 |
O1 |
O2 |
O3 |
O4 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
||||||||||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
not in scope |
not in scope |
not in scope |
not in scope |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
not in scope |
not in scope |
not in scope |
not in scope |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
not in scope |
not in scope |
not in scope |
not in scope |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
IF |
IF |
IF |
IF |
IF |
not in scope |
not in scope |
not in scope |
not in scope |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
X |
X |
A |
A |
A |
X |
X |
X |
X |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
X |
X |
not in scope |
not in scope |
X |
X |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X Modification to the routing and length of the refuelling duct and re-positioning of the original tank inboard is permissible provided all installation requirements are met. |
X |
X |
X |
X |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
G |
X |
G |
G |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
G |
X |
G |
G |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
G |
X |
G |
G |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
G |
X |
G |
G |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
G Completed vehicles are deemed to comply with the frontal off-set impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
G Completed vehicles are deemed to comply with the frontal full-width impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
G |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A + G Completed vehicles are deemed to comply with cab impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
G Completed vehicles are deemed to comply with side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A + G Completed vehicles are deemed to comply with pole side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A + G Completed vehicles are deemed to comply with rear impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
not in scope |
not in scope |
G |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
||||||||||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
X |
X |
A May be partly exempted if non-removable equipment on the rear of the vehicle prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the rear of the vehicle prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the rear of the vehicle prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
no requirements yet |
no requirements yet |
not in scope |
no requirements yet |
no requirements yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
X Glazing material may be either of safety glass or rigid plastic glazing. |
X Glazing material may be either of safety glass or rigid plastic glazing. |
X Glazing material may be either of safety glass or rigid plastic glazing. |
X Glazing material may be either of safety glass or rigid plastic glazing. |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
not in scope |
not in scope |
not in scope |
not in scope |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
not in scope |
not in scope |
not in scope |
not in scope |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
||||||||||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
n/a |
n/a |
not in scope |
n/a |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
G |
G |
G |
G Anti-lock braking system is not mandatory for vehicles with hydrostatic drive. |
G Anti-lock braking system is not mandatory for vehicles with hydrostatic drive. |
X |
X |
X |
X |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
n/a |
n/a |
n/a |
n/a |
n/a |
not in scope |
not in scope |
X |
X |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
n/a |
not in scope |
n/a |
n/a |
not in scope |
not in scope |
not in scope |
not in scope |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
A |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
X |
X |
not in scope |
not in scope |
X |
X |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
equipment |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
||||||||||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
IF G |
IF G |
X |
IF G |
IF G |
not in scope |
not in scope |
not in scope |
not in scope |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
A May be partly exempted if non-removable equipment on the front of the cab prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements |
not in scope |
not in scope |
not in scope |
not in scope |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
not in scope |
not in scope |
not in scope |
not in scope |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF |
IF |
IF |
IF |
IF |
not in scope |
not in scope |
not in scope |
not in scope |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
||||||||||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
IF |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
A |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
no requirement yet |
not in scope |
not in scope |
not in scope |
not in scope |
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
||||||||||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X Application limited to doors giving access to seats designated for normal use when the vehicle is used on a public road and where the distance between the R-point of the seat and the average plane of the door surface, measured perpendicular to the longitudinal medium plane of the vehicle, does not exceed 500 mm. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
X |
X |
B |
B |
B |
not in scope |
not in scope |
not in scope |
not in scope |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
A |
A |
A |
A |
A |
not in scope |
not in scope |
not in scope |
not in scope |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
X |
X |
X |
X |
X |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
IF X |
IF X |
IF X |
IF X |
X |
X |
X |
X |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
X |
X |
X |
X |
X |
X |
X |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
||||||||||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
G Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
not in scope |
not in scope |
not in scope |
not in scope |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
not in scope |
X Modification of exhaust system length after the last silencer not ex ceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
X Modification of exhaust system length after the last silencer not ex ceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
not in scope |
not in scope |
not in scope |
not in scope |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
Not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not ex ceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
X Modification of exhaust system length after the last silencer not ex ceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
X Modification of exhaust system length after the last silencer not ex ceeding 2,0 m is permissible without any further test. Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive. |
not in scope |
not in scope |
not in scope |
not in scope |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
X Modification of exhaust system length after the last silencer not exceeding 2,0 m is permissible without any further test. |
not in scope |
not in scope |
not in scope |
not in scope |
|
G6 |
Crankcase emissions |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G8 |
Low-temperature tailpipe emissions in lab |
Regulation (EC) No 715/2007 |
X |
not in scope |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G9 |
On-board diagnostics |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G10 |
Absence of defeat device |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G12 |
Anti-tampering |
Regulation (EC) No 715/2007 Regulation (EC) No 595/2009 |
X |
X |
X |
X |
X |
not in scope |
not in scope |
not in scope |
not in scope |
|
G13 |
Recyclability |
Directive 2005/64/EC |
not in scope |
not in scope |
n/a However, Annex V on prohibition of reuse of the specified component parts shall apply. |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
not in scope |
not in scope |
X |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
not in scope |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
||||||||||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858, Annex IV UN Regulation No 156 |
X |
X |
X |
X |
X |
X |
X |
|
|
Appendix 5
Mobile cranes
|
Item |
Subject |
Regulatory act |
N3 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
not in scope |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
not in scope |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
X |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
IF B |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
A Not required for vehicles meeting the provisions Annex I, Part A, point 4.3(b)(ii) and (iii), as well as point 4.3(c). |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
A |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
A |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
A |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
X |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
X |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
not in scope |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
not in scope |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
not in scope |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
A |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
not in scope |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
not in scope |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
not in scope |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
not in scope |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
not in scope |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
not in scope |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
not in scope |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
A |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
A |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
A |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
not in scope |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
no requirements yet |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
X For all glazing other than the windscreen and side windows located forward of the driver’s eye points, the material may be either of safety glass or rigid plastic glazing. |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
X |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
X Crab steering allowed |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
n/a |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
not in scope |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
G Test to be performed only with the complete/completed vehicle. Vehicles up to 4 axles shall comply with all the requirements laid down in the relevant regulatory acts. Derogations are admitted for vehicles having more than 4 axles, provided that: (a) they are justified by the particular construction; and (b) all the braking performances, related to parking, service and secondary braking laid down in the relevant regulatory act are fulfilled. Anti-lock braking system is not mandatory for vehicles with hydrostatic drive. |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
not in scope |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
n/a |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
not in scope |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
X |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
IF G |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X n/a in case of complete vehicle |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
X |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
A Only to be applied in case of a chassis-cab base vehicle and n/a in all other cases. |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
A Provided that all mandatory lighting devices are installed |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
not in scope |
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
A Only to be applied in case of a chassis-cab base vehicle and n/a in all other cases. |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
n/a |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
no requirement yet |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
not in the scope |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
no requirement yet |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
no requirement yet |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
no requirement yet |
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
not in scope |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
A |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
not in scope |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
A |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
A |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
not in scope |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
A Not required for vehicles meeting the provisions Annex I, Part A, point 4.3(b)(ii) and (iii), as well as point 4.3(c). |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
A |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
n/a |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
not in scope |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
not in scope |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
G Test to be performed only with the complete/completed vehicle. The vehicle can be tested in accordance with Directive 70/157/EEC, UN Regulation No 51.02 or Regulation (EC) No 540/2014. The following limit values are applicable, irrespective of the vehicle conditions such as engine type, gearbox type and any sub-classifications: (a) 81 dB(A) for vehicles with an engine power of less than 75 kW; (b) 83 dB(A) for vehicles with an engine power of not less than 75 kW but less than 150 kW; (c) 84 dB(A) for vehicles with an engine power of not less than 150 kW. |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
not in scope |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
not in scope |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
Not in scope |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
Not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 595/2009 |
not in scope |
|
G6 |
Crankcase emissions |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
not in scope |
|
G8 |
Low-temperaturetailpipe emissions in lab |
Regulation (EC) No 715/2007 |
not in scope |
|
G9 |
On-board diagnostics |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G10 |
Absence of defeat device |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G12 |
Anti-tampering |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may apply. |
|
G13 |
Recyclability |
Directive 2005/64/EC |
not in scope |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
not in scope |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858, Annex IV UN Regulation No 156 |
X |
Appendix 6
Exceptional load transport vehicles
|
Item |
Subject |
Regulatory acts |
N3 |
O4 |
|
A |
RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY |
|||
|
A1 |
Interior fittings |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A2 |
Seats and head restraints |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. Seats that are not designated as such shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. |
not in scope |
|
A3 |
Bus seats |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A4 |
Safety-belt anchorages |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
not in scope |
|
A5 |
Safety-belts and restraint systems |
Regulation (EU) 2019/2144 |
X Application limited to seats designated for normal use when the vehicle is used on a public road. |
not in scope |
|
A6 |
Safety-belt reminders |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
A7 |
Partitioning systems |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
A8 |
Child restraint anchorages |
Regulation (EU) 2019/2144 |
IF B |
not in scope |
|
A9 |
Child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
A10 |
Enhanced child restraint systems (IF) |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
A11 |
Front underrun protection |
Regulation (EU) 2019/2144 |
A |
not in scope |
|
A12 |
Rear underrun protection |
Regulation (EU) 2019/2144 |
A |
A |
|
A13 |
Lateral protection |
Regulation (EU) 2019/2144 |
X |
A |
|
A14 |
Fuel tank safety (IF) |
Regulation (EU) 2019/2144 |
A |
A |
|
A15 |
Liquified petroleum gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
A16 |
Compressed and liquified natural gas safety (IF) |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
A17 |
Hydrogen safety (IF) |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
A18 |
Hydrogen system material qualification (IF) |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
A19 |
In-use electric safety (IF) |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
A20 |
Frontal off-set impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A21 |
Frontal full-width impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A22 |
Protective steering |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A23 |
Replacement airbag |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
A24 |
Cab impact |
Regulation (EU) 2019/2144 |
A |
not in scope |
|
A25 |
Side impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A26 |
Pole side impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A27 |
Rear impact |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
A28 |
112-based eCall in-vehicles systems |
Regulation (EU) 2015/758 |
not in scope |
not in scope |
|
B |
VULNERABLE ROAD USERS, VISION AND VISIBILITY |
|||
|
B1 |
Pedestrian leg and head protection |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
B2 |
Enlarged head impact zone |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
B3 |
Frontal protection system |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
B4 |
Advanced emergency braking for pedestrians and cyclists ahead |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
B5 |
Pedestrian and cyclist collision warning |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
B6 |
Blind spot information system |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
B7 |
Reversing detection |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
B8 |
Forward vision |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
B9 |
Heavy-duty vehicles direct vision |
Regulation (EU) 2019/2144 |
no requirements yet |
not in scope |
|
B10 |
Safety glazing |
Regulation (EU) 2019/2144 |
X |
X Glazing material may be either of safety glass or rigid plastic glazing. |
|
B11 |
Defrost/demist |
Regulation (EU) 2019/2144 |
X Vehicles shall be fitted with an adequate windscreen defrosting and demisting device |
not in scope |
|
B12 |
Wash/wipe |
Regulation (EU) 2019/2144 |
X Vehicles shall be fitted with adequate windscreen washing and wiping devices |
not in scope |
|
B13 |
Indirect vision devices |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
B14 |
Acoustic Vehicle Alerting Systems |
Regulation (EU) No 540/2014 |
X |
not in scope |
|
C |
VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |
|||
|
C1 |
Steering equipment |
Regulation (EU) 2019/2144 |
X Crab steering allowed |
X |
|
C2 |
Lane departure warning |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
|
C3 |
Emergency lane keeping |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
C4 |
Braking |
Regulation (EU) 2019/2144 |
G Test to be performed only with the complete/completed vehicle. Vehicles up to 4 axles shall comply with all the requirements laid down in the relevant regulatory acts. Derogations are admitted for vehicles having more than 4 axles, provided that: (a) they are justified by the particular construction; and (b) all the braking performances, related to parking, service and secondary braking laid down in the relevant regulatory act are fulfilled. Anti-lock braking system is not mandatory for vehicles with hydrostatic drive. |
X |
|
C5 |
Replacement braking parts |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
C6 |
Brake assist |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
C7 |
Stability control |
Regulation (EU) 2019/2144 |
n/a |
X |
|
C8 |
Advanced emergency braking on heavy-duty vehicles |
Regulation (EU) 2019/2144 |
n/a |
not in scope |
|
C9 |
Advanced emergency braking on light-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
C10 |
Tyre safety and environmental performance |
Regulation (EU) 2019/2144 |
X |
X Tyres are to be type-approved in accordance with the requirements set out in UN Regulation No 117 even if the design speed of the vehicle is less than 80 km/h. |
|
C11 |
Spare wheels and run-flat systems (IF) |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
C12 |
Retreaded tyres |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
C13 |
Tyre pressure monitoring for light-duty vehicles |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
C14 |
Tyre pressure monitoring for heavy-duty vehicles |
Regulation (EU) 2019/2144 |
A |
A |
|
C15 |
Tyre installation |
Regulation (EU) 2019/2144 |
X |
X Tyres are to be type-approved in accordance with the requirements set out in UN Regulation No 54 even if the design speed of the vehicle is less than 80 km/h. The load capacity may be adjusted in relation to the maximum design speed of the trailer in agreement with the tyre manufacturer. |
|
C16 |
Replacement wheels |
Regulation (EU) 2019/2144 |
equipment |
equipment |
|
D |
ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS |
|||
|
D1 |
Audible warning |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D2 |
Radio interference (electromagnetic compatibility) |
Regulation (EU) 2019/2144 |
X |
X |
|
D3 |
Protection against unauthorised use, immobiliser and alarm systems |
Regulation (EU) 2019/2144 |
IF G |
not in scope |
|
D4 |
Protection of vehicle against cyberattacks |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D5 |
Speedometer |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D6 |
Odometer |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D7 |
Speed limitation devices |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D8 |
Intelligent speed assistance |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D9 |
Identification of controls, tell-tales and indicators |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
D10 |
Heating systems |
Regulation (EU) 2019/2144 |
X |
X |
|
D11 |
Light signalling devices |
Regulation (EU) 2019/2144 |
X |
X |
|
D12 |
Road illumination devices |
Regulation (EU) 2019/2144 |
X |
X |
|
D13 |
Retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
X |
|
D14 |
Light sources |
Regulation (EU) 2019/2144 |
X |
X |
|
D15 |
Installation of light signalling, road illumination and retro-reflective devices |
Regulation (EU) 2019/2144 |
X |
A Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected |
|
D16 |
Emergency stop signal |
Regulation (EU) 2019/2144 |
X Only for vehicles fitted with electronically controlled anti-lock braking system |
not in scope |
|
D17 |
Headlamp cleaners (IF) |
Regulation (EU) 2019/2144 |
IF |
not in scope |
|
D18 |
Gear shift indicator |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
E |
DRIVER AND SYSTEM BEHAVIOUR |
|||
|
E1 |
Alcohol interlock installation facilitation |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
E2 |
Driver drowsiness and attention warning |
Regulation (EU) 2019/2144 |
A |
not in scope |
|
E3 |
Advanced driver distraction warning |
Regulation (EU) 2019/2144 |
No requirement yet |
not in scope |
|
E4 |
Driver availability monitoring system (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
Not in the scope |
not in scope |
|
E5 |
Event data recorder |
Regulation (EU) 2019/2144 |
No requirement yet |
not in scope |
|
E6 |
Systems to replace driver’s control (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
No requirement yet |
not in scope |
|
E7 |
Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
No requirement yet |
not in scope |
|
E8 |
Platooning (IF) |
Regulation (EU) 2019/2144 |
No requirement yet |
not in scope |
|
E9 |
Systems to provide safety information to other road users (in case of automated vehicles) |
Regulation (EU) 2019/2144 |
No requirement yet |
not in scope |
|
F |
GENERAL VEHICLE CONSTRUCTION AND FEATURES |
|||
|
F1 |
Registration plate space |
Regulation (EU) 2019/2144 |
X |
X |
|
F2 |
Reversing motion |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
F3 |
Door latches and hinges |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
F4 |
Door entry steps, handholds and running boards |
Regulation (EU) 2019/2144 |
X |
not in scope |
|
F5 |
External projections |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
F6 |
External projections of commercial vehicle cabs |
Regulation (EU) 2019/2144 |
A |
not in scope |
|
F7 |
Statutory plate and vehicle identification number |
Regulation (EU) 2019/2144 |
X |
X |
|
F8 |
Towing devices |
Regulation (EU) 2019/2144 |
A |
not in scope |
|
F9 |
Wheel guards |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
F10 |
Spray suppression systems |
Regulation (EU) 2019/2144 |
X |
A |
|
F11 |
Masses and dimensions |
Regulation (EU) 2019/2144 |
A |
A |
|
F12 |
Mechanical couplings |
Regulation (EU) 2019/2144 |
IF X |
X |
|
F13 |
Vehicles intended for the transportation of dangerous goods (IF) |
Regulation (EU) 2019/2144 |
X |
X |
|
F14 |
General bus construction |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
F15 |
Bus strength of superstructure |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
F16 |
Flammability in buses |
Regulation (EU) 2019/2144 |
not in scope |
not in scope |
|
G |
ENVIRONMENTAL PERFORMANCE AND EMISSIONS |
|||
|
G1 |
Sound level |
Regulation (EU) No 540/2014 |
G Test to be performed only with the complete/completed vehicle. The vehicle can be tested in accordance with Directive 70/157/EEC, UN Regulation No 51.02 or Regulation (EC) No 540/2014. The following limit values are applicable, irrespective of the vehicle conditions such as engine type, gearbox type and any sub-classifications: (a) 81 dB(A) for vehicles with an engine power of less than 75 kW; (b) 83 dB(A) for vehicles with an engine power of not less than 75 kW but less than 150 kW; (c) 84 dB(A) for vehicles with an engine power of not less than 150 kW. |
not in scope |
|
G2 |
Tailpipe emissions of vehicle in lab |
Regulation (EC) No 715/2007 |
not in scope |
not in scope |
|
G2a |
Determination of specific CO2 emissions and fuel consumption of vehicle and device for monitoring on board the vehicle the consumption of fuel and/or electric energy |
Regulation (EC) No 715/2007 |
not in scope |
not in scope |
|
G3 |
Tailpipe emissions of engine in lab |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive |
not in scope |
|
G3a |
Determination of specific CO2 emissions and fuel consumption of vehicle |
Regulation (EC) No 595/2009 |
not in scope |
not in scope |
|
G3b |
Determination of specific energy efficiency performance of trailer |
Regulation (EC) No 595/2009 |
not in scope |
not in scope |
|
G4 |
Tailipipe emissions on the road |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive |
not in scope |
|
G5 |
Durability of tailpipe emissions |
Regulation (EC) No 595/2009 |
X |
not in scope |
|
G6 |
Crankcase emissions |
Regulation (EC) No 595/2009 |
X |
not in scope |
|
G7 |
Evaporative emissions |
Regulation (EC) No 715/2007 |
not in scope |
not in scope |
|
G8 |
Low-temperature tailpipe emissions in lab |
Regulation (EC) No 715/2007 |
not in scope |
not in scope |
|
G9 |
On-board diagnostics |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive |
not in scope |
|
G10 |
Absence of defeat device |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive |
not in scope |
|
G11 |
Auxiliary emissions strategies |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive |
not in scope |
|
G12 |
Anti-tampering |
Regulation (EC) No 595/2009 |
X Alternatively, Regulation (EU) 2016/1628 may also apply to vehicles with hydrostatic drive |
not in scope |
|
G13 |
Recyclability |
Directive 2005/64/EC |
not in scope |
not in scope |
|
G14 |
Air-conditioning systems |
Directive 2006/40/EC |
not in scope |
not in scope |
|
H |
ACCESS TO VEHICLE INFORMATION AND SOFTWARE UPDATE |
|||
|
H1 |
Access to vehicle OBD information and vehicle repair and maintenance information |
Regulation (EU) 2018/858, Articles 61 to 66 and Annex X |
X |
X |
|
H2 |
Software update |
Regulation (EU) 2018/858, Annex IV UN Regulation No 156 |
X |
X |
ANNEX III
PROCEDURES TO BE FOLLOWED WITH RESPECT TO EU TYPE-APPROVAL
1. Objectives and scope
|
1.1. |
This Annex establishes the procedures for the proper conduct of the vehicle type-approval in accordance with Articles 26, 27 and 28. |
|
1.2. |
It also includes:
(a)
the list of international standards which are of relevance for the designation of the technical services in accordance with Articles 68 and 70;
(b)
the description of the procedure to be followed for the assessment of the skills of technical services in accordance with Article 73;
(c)
the general requirements for the drafting of test reports by technical services. |
2. Type-approval procedure
When receiving an application for vehicle type-approval, the approval authority shall:
verify that all EU type-approval certificates issued pursuant to the regulatory acts as listed in Annex II which are applicable for vehicle type-approval cover the type of vehicle and correspond to the prescribed requirements;
make sure that the vehicle specifications and data are included in the data in the information packages and in the EU type-approval certificates issued in accordance with the relevant regulatory acts;
when an item number is not included in the information package as provided for in any of the regulatory acts, confirm that the relevant part or characteristic conforms to the particulars in the information folder;
on a selected sample of vehicles from the type to be approved carry out or arrange to be carried out inspections of vehicle parts and systems to verify that the vehicle or vehicles are built in accordance with the relevant data contained in the authenticated information package in respect of the relevant EU type-approval certificates;
carry out or arrange to be carried out relevant installation checks in respect of separate technical units, where applicable;
carry out or arrange to be carried out necessary checks in respect of the presence of the devices provided for in explanatory notes 1 and 2 of Part I of Annex II, where applicable;
carry out or arrange to be carried out necessary checks in order to ensure that the requirements set out in explanatory note 5 of Part I of Annex II are fulfilled.
3. Combination of technical specifications
The number of vehicles to be submitted shall be sufficient to permit the proper check of the various combinations to be type-approved according to the following criteria:
|
Technical specifications |
Vehicle category |
|||||||||
|
M1 |
M2 |
M3 |
N1 |
N2 |
N3 |
O1 |
O2 |
O3 |
O4 |
|
|
Engine |
X |
X |
X |
X |
X |
X |
— |
— |
— |
— |
|
Gear box |
X |
X |
X |
X |
X |
X |
— |
— |
— |
— |
|
Number of axles |
— |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
Powered axles (number, position and interconnection) |
X |
X |
X |
X |
X |
X |
— |
— |
— |
— |
|
Steered axles (number and position) |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
Body styles |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
Number of doors |
X |
X |
X |
X |
X |
X |
X |
X |
X |
X |
|
Hand of drive |
X |
X |
X |
X |
X |
X |
— |
— |
— |
— |
|
Number of seats |
X |
X |
X |
X |
X |
X |
— |
— |
— |
— |
|
Level of equipment |
X |
X |
X |
X |
X |
X |
— |
— |
— |
— |
4. Specific provisions
Where no approval certificates as provided for in the relevant regulatory acts are available, the approval authority shall:
arrange for the necessary tests and checks as required by each of the relevant regulatory acts;
verify that the vehicle conforms to the particulars in the information folder and that it meets the technical requirements of each of the relevant regulatory acts;
carry out or arrange to be carried out relevant installation checks in respect of separate technical units, where applicable;
carry out or arrange to be carried out necessary checks in respect of the presence of the devices provided for in explanatory notes 1 and 2 of Part I of Annex II where applicable;
carry out or arrange to be carried out necessary checks in order to ensure that the requirements set out in explanatory note 5 of Part I of Annex II are fulfilled.
Appendix 1
Standards with which the technical services referred to in Article 68 have to comply
|
1. |
Activities related to testing for type-approval to be carried out in accordance with the regulatory acts listed in Annex II:
|
|
2. |
Activities related to conformity of production
|
Appendix 2
Procedure for the assessment of the technical services
1. Objective and scope
|
1.1. |
This Appendix establishes the conditions in accordance with which the assessment procedure of the technical services shall be conducted by the authority, competent under Article 73 (‘competent authority’). |
|
1.2. |
Those requirements shall apply to all technical services, irrespective of their legal status (independent organisation, manufacturer or approval authority acting as technical service). |
2. Assessments
The carrying out of an assessment shall be governed by the following:
principle of independence, which is the basis for the impartiality and objectivity of the conclusions; and
an evidence-based approach, which guarantees reliable and reproducible conclusions.
Auditors shall show trust and integrity. They shall respect confidentiality and discretion.
They shall report truthfully and accurately about findings and conclusions.
3. Skills requirements for auditors
|
3.1. |
The assessments may only be conducted by auditors having the technical and administrative knowledge necessary for such purposes. |
|
3.2. |
The auditors shall have been trained specifically for assessment activities. In addition, they shall have the specific knowledge of the technical area in which the technical service will exercise its activities. |
|
3.3. |
Without prejudice to points 3.1 and 3.2, the assessment referred to in Article 73 shall be conducted by auditors independent of the activities for which the assessment is conducted. |
4. Application for designation
|
4.1. |
A duly authorised representative of the applicant technical service shall submit a formal application to the competent authority that includes the following information:
(a)
general features of the technical service, including corporate entity, name, addresses, legal status and technical resources;
(b)
a detailed description, including curriculum vitae, of the personnel in charge of testing and of the managerial staff, setting out their educational qualifications and professional skills;
(c)
technical services which use virtual testing methods shall provide evidence of their ability to work in a Computer-Aided-x environment;
(d)
general information concerning the technical service, including its activities, its relationship in a larger corporate entity, if any, and addresses of all its physical location(s) to be covered by the scope of designation;
(e)
an agreement to fulfil the requirements for designation and the other obligations of the technical service as provided for in the relevant regulatory acts for which it is designated;
(f)
a description of the conformity assessment services that the technical service undertakes in the framework of the relevant regulatory acts and a list of the regulatory acts for which the technical service applies for designation, including limits of capability, where applicable;
(g)
a copy of the quality assurance manual of the technical service. |
|
4.2. |
The competent authority shall review the adequacy of the information provided by the technical service. |
|
4.3. |
The technical service shall notify to the competent authority any modifications to the information provided in accordance with point 4.1. |
5. Resource review
The competent authority shall review its ability to carry out the assessment of the technical service, in terms of its own policy, its competence and the availability of suitable auditors and experts.
6. Subcontracting the assessment
|
6.1. |
The competent authority may subcontract parts of the assessment to another competent authority or ask for support from technical experts provided by other competent authorities. The subcontractors and experts have to be accepted by the applicant technical service. |
|
6.2. |
The competent authority shall take into account accreditation certificates with adequate scope in order to complete its global assessment of the technical service. |
7. Preparation for assessment
|
7.1. |
The competent authority shall formally appoint a joint assessment team. The competent authority shall ensure that the expertise brought to each joint assessment team is appropriate. In particular, the joint assessment team as a whole shall have both:
(a)
appropriate knowledge of the specific scope for which designation is sought; and
(b)
sufficient understanding to reliably assess the competence of the technical service to operate within its scope of designation. |
|
7.2. |
The competent authority shall clearly define the assignment given to the joint assessment team. The task of the joint assessment team is to review the documents collected from the applicant technical service and to conduct the on-site assessment. |
|
7.3. |
The competent authority shall agree, together with the technical service and the assigned assessment team, to the date and timetable for the assessment. However, it remains the responsibility of the competent authority to pursue a date that is in accordance with the surveillance and reassessment plan. |
|
7.4. |
The competent authority shall ensure that the joint assessment team is provided with the appropriate criteria documents, previous assessment records, and the relevant documents and records of the technical service. |
8. On-site assessment
The joint assessment team shall conduct the assessment of the technical service at the premises of the technical service from which one or more key activities are performed and, where relevant, shall perform eyewitness assessment at other selected locations where the technical service operates.
9. Analysis of findings and assessment report
|
9.1. |
The joint assessment team shall analyse all relevant information and evidence gathered during the document and record review and the on-site assessment. That analysis shall be sufficient to allow the team to determine the extent of competence and conformity of the technical service with the requirements for designation. |
|
9.2. |
The competent authority's reporting procedures shall ensure that the following requirements are fulfilled.
|
|
9.3. |
The competent authority shall ensure that the responses of the technical service are sufficient and effective to resolve non-compliance. If the technical service responses are found to be insufficient, further information shall be requested. Additionally, evidence of effective implementation of actions taken may be requested, or a follow-up assessment may be carried out, to verify effective implementation of corrective actions. |
|
9.4. |
The assessment report shall include at least the following:
(a)
unique identification of the technical service;
(b)
date(s) of the on-site assessment;
(c)
name(s) of the auditors(s) and/or expert(s) involved in the assessment;
(d)
unique identification of all premises assessed;
(e)
proposed scope of designation that was assessed;
(f)
a statement on the adequacy of the internal organisation and procedures adopted by the technical service supporting its competence, as determined through its fulfilment of the requirements for designation;
(g)
information on resolving all non-compliance;
(h)
a recommendation of whether the applicant should be designated or confirmed as technical service and, if so, the scope of designation. |
10. Granting, confirming or extending a designation
|
10.1. |
The competent authority shall, without undue delay, make the decision on whether to grant, confirm or extend a designation on the basis of the assessment report(s) and any other relevant information. |
|
10.2. |
The competent authority shall provide a certificate to the technical service. That certificate shall identify the following:
(a)
the identity and logo of the competent- authority;
(b)
the unique identity of the designated technical service;
(c)
the effective date of designation and the expiry date;
(d)
a brief indication of or a reference to the scope of designation (relevant regulatory acts or part of them);
(e)
a statement of conformity and a reference to this Regulation. |
11. Reassessment and surveillance
|
11.1. |
Reassessment is similar to an initial assessment except that experience gained during previous assessments shall be taken into account. Surveillance on-site assessments are less comprehensive than reassessments. |
|
11.2. |
The competent authority shall design its plan for reassessment and surveillance of each designated technical service so that representative samples of the scope of designation are assessed on a regular basis. The interval between on-site assessments, whether reassessment or surveillance, depends on the proven stability that the technical service has reached. |
|
11.3. |
Where, during surveillance or reassessments, non-compliance is identified, the competent authority shall define strict time limits for corrective actions to be taken. |
|
11.4. |
Where the corrective or improvement actions have not been taken within the agreed time limit or are not deemed to be sufficient, the competent authority shall adopt appropriate measures, such as conducting a further assessment, or suspending or withdrawing the designation for one or more of the activities for which the technical service has been designated. |
|
11.5. |
Where the competent authority decides to suspend or withdraw the designation of a technical service, it shall inform the technical service of its decision by registered mail. In any case, the competent authority shall adopt all the necessary measures to ensure the continuity of the activities already undertaken by the technical service. |
12. Records on designated technical services
|
12.1. |
The competent authority shall maintain records on technical services to demonstrate that the requirements for designation, including competence, have been effectively fulfilled. |
|
12.2. |
The competent authority shall keep the records on technical services secure to ensure confidentiality. |
|
12.3. |
Records on technical services shall include at least the following:
(a)
relevant correspondence;
(b)
assessment records and reports;
(c)
copies of designation certificates. |
ANNEX IV
CONFORMITY OF PRODUCTION PROCEDURES
1. Objectives
|
1.1. |
The conformity of production procedure aims to ensure that each vehicle, system, component and technical separate unit, part or equipment produced is in conformity with the approved type. |
|
1.2. |
The conformity of production procedure shall always include the assessment of quality-assurance management systems, referred to in point 2 as the ‘initial assessment’, and the verification of the type-approval subject and product-related controls, referred to in point 3 as ‘product conformity arrangements’. |
2. Initial assessment
|
2.1. |
Before granting type-approval, the approval authority shall verify that the manufacturer has established satisfactory arrangements and procedures for ensuring that vehicles, systems, components, separate technical units or parts and equipment are produced in conformity with the approved type. |
|
2.2. |
Guidance for conducting those assessments may be found in standard EN ISO 19011:2011 — Guidelines for auditing management systems. |
|
2.3. |
Compliance with the requirements of point 2.1 shall be verified to the satisfaction of the approval authority, as follows: The approval authority shall be satisfied with the initial assessment and the product conformity arrangements referred to in point 3, taking into account one of the arrangements referred to in points 2.3.1 to 2.3.3, or a combination of those arrangements in full or in part as appropriate.
|
|
2.4. |
For the purpose of vehicle type-approval, the initial assessments carried out for the granting of type-approvals for systems, components and separate technical units of the vehicle need not be repeated, but shall be completed by an assessment of the locations and activities relating to the assembly of the whole vehicle that have not been covered by the initial assessments. |
3. Product conformity arrangements
|
3.1. |
Every vehicle, system, component or separate technical unit, part or item of equipment approved pursuant to a UN Regulation annexed to the Revised 1958 Agreement and to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of this Annex, the said UN Regulation and this Regulation. |
|
3.2. |
Before granting a type-approval pursuant to this Regulation and to a UN Regulation annexed to the Revised 1958 Agreement, the approval authority shall verify the existence of adequate product conformity arrangements and documented control plans, to be agreed with the manufacturer for each approval, to carry out at specified intervals the tests or associated checks that are necessary to verify continued conformity with the approved type, including, where applicable, tests specified in this Regulation and the said UN Regulation. |
|
3.3. |
The holder of the type-approval shall, in particular:
3.3.1.
ensure the existence and application of procedures for effective control of the conformity of vehicles, systems, components, separate technical units, parts or equipment to the approved type;
3.3.2.
have access to the testing or other appropriate equipment necessary for checking the conformity to each approved type;
3.3.3.
ensure that the data resulting from tests or checks are recorded and that annexed documents remain available for a period of up to 10 years to be determined in agreement with the approval authority;
3.3.4.
analyse the results of each type of test or check, in order to verify and ensure the stability of the product characteristics, making allowance for variation of an industrial production;
3.3.5.
ensure that for each type of product, at least the checks prescribed in this Regulation and the tests prescribed in the relevant regulatory acts listed in Annex II are carried out;
3.3.6.
ensure that any set of samples or test pieces that gives evidence of non-conformity in the type of test in question, gives rise to a further sampling and testing. All the necessary steps shall be taken to restore the production process to ensure conformity with the approved type. |
|
3.4. |
In the case of step-by-step, mixed or multi-stage type-approvals, the approval authority that is granting a whole-vehicle type-approval may request from any approval authority that has granted type-approval of any relevant system, component or separate technical unit specific details regarding compliance with the conformity of production requirements set out in this Annex. |
|
3.5. |
The approval authority that is granting a whole-vehicle type-approval and is not satisfied with the reported information referred to in point 3.4., and that has communicated this in writing to the relevant manufacturer and to the approval authority granting the type-approval for the system, component or separate technical unit, shall request the performance of additional conformity of production audits or checks, which shall be performed at the site of the manufacturer(s) of those systems, components or separate technical units. The results of this additional conformity of production audits or checks shall immediately be made available to that approval authority. |
|
3.6. |
Where points 3.4. and 3.5. apply and the approval authority granting the whole-vehicle type-approval has not been satisfied with the additional audit or check results, the manufacturer shall ensure that conformity of production is restored as soon as possible to the satisfaction of that approval authority and of the approval authority granting type-approval of the system, component or separate technical unit. |
4. Continued verification arrangements
|
4.1. |
The approval authority that has granted type-approval may at any time verify the conformity control methods applied in each production facility by means of periodic audits. The manufacturer shall for that purpose allow access to that authority to the manufacturing, inspection, testing, storage and distribution sites and shall provide all necessary information with regard to the quality management system documentation and records.
|
|
4.2. |
At every review, records of tests or checks and records of production, in particular records of those tests or checks documented as required in point 2.2, shall be made available to the inspector. |
|
4.3. |
The inspector may select samples at random manner to be tested in the manufacturer's laboratory or in the facilities of the technical service. In such a case only physical test shall be carried out. The minimum number of samples may be determined on the basis of the results of the manufacturer's own verification. |
|
4.4. |
The inspector who is of the opinion that the level of control is unsatisfactory, or who deems it necessary to verify the validity of the tests carried out in accordance with point 4.2, shall select samples to be sent to a technical service to perform physical tests in accordance with the requirements on conformity of production, set out in the regulatory acts listed in Annex II. |
|
4.5. |
Where unsatisfactory results are found during an inspection or a monitoring review, the approval authority shall take all necessary steps to ensure that the manufacturer restores the conformity of production as rapidly as possible. |
|
4.6. |
In cases where compliance with UN Regulations is required by this Regulation, the manufacturer may choose to apply this Annex as an equivalent alternative to the conformity of production requirements in the respective UN Regulations. However, if points 4.4. or 4.5. apply, all separate conformity of production requirements in the UN Regulations have to be complied with to the satisfaction of the approval authority until it decides that conformity of production has been restored. |
5. Arrangements concerning software update
The software update management system of the manufacturer as well as the whole vehicle type shall comply with the requirements as set out in UN Regulation 156.
ANNEX V
SMALL SERIES AND END-OF-SERIES LIMITS
A. SMALL SERIES QUANTITIVE ANNUAL LIMITS
|
1. |
The number of units of one type of vehicle to be registered, made available on the market or entered into service annually in the Union shall not exceed, pursuant to Article 41, the quantitive annual limits shown in the following table for the vehicle category in question:
|
|
2. |
The number of units of one type of vehicle to be registered, made available on the market or entered into service annually in a Member State, shall be determined by that Member State but shall not exceed, pursuant to Article 42, the quantitative annual limits shown in the following table for the vehicle category in question:
|
B. END-OF-SERIES LIMITS
The maximum number of complete and completed vehicles entered into service in each Member State under the procedure ‘End-of-Series’ shall be restricted in one of the following ways to be chosen by the Member State:
The maximum number of vehicles of one or more types may, in the case of category M1, not exceed 10 % and in the case of all other categories not exceed 30 % of the vehicles of all types concerned entered into service in that Member State during the previous year. Should 10 %, respectively 30 %, be less than 100 vehicles, then the Member State may allow the entry into service of a maximum of 100 vehicles.
Vehicles of any one type shall be restricted to those for which a valid certificate of conformity was issued on or after the date of manufacture of the vehicle and which remained valid for at least three months after its date of issue but subsequently lost its validity due to the entry into force of a regulatory act.
ANNEX VI
LIST OF PARTS OR EQUIPMENT THAT MAY POSE A SERIOUS RISK TO THE CORRECT FUNCTIONING OF SYSTEMS THAT ARE ESSENTIAL FOR THE SAFETY OF THE VEHICLE OR ITS ENVIRONMENTAL PERFORMANCE, THE PERFORMANCE REQUIREMENTS OF SUCH PARTS AND EQUIPMENT, THE APPROPRIATE TEST PROCEDURES, AND MARKING AND PACKAGING PROVISIONS
I. Parts or equipment having a significant impact on vehicle safety
|
Item No |
Item description |
Performance requirement |
Test procedure |
Marking requirement |
Packaging requirements |
|
1 |
[…] |
|
|
|
|
|
2 |
|
|
|
|
|
|
3 |
|
|
|
|
|
II. Parts or equipment having a significant impact on the environmental performance of the vehicle
|
Item No |
Item description |
Performance requirement |
Test procedure |
Marking requirement |
Packaging requirements |
|
1 |
[…] |
|
|
|
|
|
2 |
|
|
|
|
|
|
3 |
|
|
|
|
|
ANNEX VII
REGULATORY ACTS FOR WHICH A MANUFACTURER MAY BE DESIGNATED AS A TECHNICAL SERVICE
1. Objectives and scope
|
1.1. |
This Annex lays down the list of the regulatory acts for which an in-house technical service of a manufacturer may be designated as a technical service in accordance with Article 72(1). |
|
1.2. |
It also includes appropriate provisions concerning the designation of an in-house technical service of a manufacturer as technical service, to be applied in the framework of the type-approval of vehicles, components and separate technical units concerned by Part I of Annex II. |
|
1.3. |
This Annex however does not apply to manufacturers who apply for the EU type-approval of vehicles produced in small series, as referred to in Article 41. |
2. Designation of an in-house technical service of a manufacturer as a technical service
|
2.1. |
An in-house technical service of a manufacturer designated as a technical service is a manufacturer which has been designated by the type-approval authority as a testing laboratory to carry out on its behalf the approval tests. The expression ‘to carry out tests’ is not restricted to the measurement of performances, but also covers the registration of test results and the submission to the type-approval authority of a report, including the relevant conclusions. It also covers the checking of compliance with those provisions that do not necessarily require measurement. This is the case for the assessment whether the design complies with the legislative requirements. |
3. List of regulatory acts and restrictions
|
|
Subject |
Regulatory act reference |
|
4A |
Space for mounting and fixing rear registration plates |
Regulation (EC) No 661/2009 Regulation (EU) No 1003/2010 |
|
7A |
Audible warning devices and signals |
Regulation (EC) No 661/2009 UN Regulation No 28 |
|
10A |
Electromagnetic compatibility |
Regulation (EC) No 661/2009 UN Regulation No 10 |
|
18A |
Manufacturer's statutory plate and VIN |
Regulation (EC) No 661/2009 Regulation (EU) No 19/2011 |
|
20A |
Installation of lighting and light-signalling devices on vehicles |
Regulation (EC) No 661/2009 UN Regulation No 48 |
|
27A |
Towing device |
Regulation (EC) No 661/2009 Regulation (EU) No 1005/2010 |
|
33A |
Location and identification of hand controls, tell-tales and indicators |
Regulation (EC) No 661/2009 UN Regulation No 121 |
|
34A |
Windscreen defrosting and demisting systems |
Regulation (EC) No 661/2009 Regulation (EU) No 672/2010 |
|
35A |
Windscreen wiper and washer systems |
Regulation (EC) No 661/2009 Regulation (EU) No 1008/2010 |
|
36A |
Heating systems |
Regulation (EC) No 661/2009 UN Regulation No 122 Except the provisions in Annex 8 relating to LPG combustion heaters and LPG heating systems |
|
37A |
Wheel guards |
Regulation (EC) No 661/2009 Regulation (EU) No 1009/2010 |
|
44A |
Masses and dimensions |
Regulation (EC) No 661/2009 Regulation (EU) No 1230/2012 |
|
45A |
Safety glazing materials and their installation on vehicles |
Regulation (EC) No 661/2009 UN Regulation No 43 Restricted to the provisions included in Annex 21 |
|
46A |
Installation of tyres |
Regulation (EC) No 661/2009 Regulation (EU) No 458/2011 |
|
46B |
Rolling resistance determination |
Regulation (EU) 2017/2400, Annex X |
|
48A |
Masses and dimensions |
Regulation (EC) No 661/2009 Regulation (EU) No 1230/2012 |
|
49A |
Commercial vehicles with regard to their external projections forward of the cab's rear panel |
Regulation (EC) No 661/2009 UN Regulation No 61 |
|
50A |
Mechanical coupling components of combinations of vehicles |
Regulation (EC) No 661/2009 UN Regulation No 55 Restricted to the provisions included in Annex 5 (up to and including paragraph 8) and Annex 7 |
|
61 |
Air-conditioning system |
Directive 2006/40/EC |
Appendix
Designation of an in-house technical service of a manufacturer as technical service and subcontracting
1. General
|
1.1. |
The designation and notification of an in-house technical service of a manufacturer as a technical service shall be made in accordance with Articles 68 to 81 and any subcontracting shall be done in accordance with this Appendix. |
2. Subcontracting
|
2.1. |
In accordance with Article 71(1), a technical service may nominate a subcontractor for performing tests on his behalf. |
|
2.2. |
For the purposes of this Appendix ‘Subcontractor’ means either a subsidiary of the technical service that has been entrusted by that technical service with testing activities inside its own organisation or a third party under contract with that technical service to perform test activities. |
|
2.3. |
The use of the services of a subcontractor does not release the technical service from its obligation to comply with Articles 69, 70, 80 and 81, and in particular with those concerning the skills of the technical services and compliance with Standard EN ISO/IEC 17025:2005. |
|
2.4. |
Point 2 of Annex VII shall apply to the subcontractor. |
3. Test report
Test reports shall be drafted in accordance with the implementing acts referred to in Article 30(3).
ANNEX VIII
CONDITIONS FOR THE USE OF VIRTUAL TESTING METHODS BY A MANUFACTURER OR A TECHNICAL SERVICE
1. Objectives and scope
This Annex lays down provisions concerning virtual testing in accordance with Article 30(7).
2. List of regulatory acts
|
|
Subject |
Regulatory act reference |
|
3B |
Rear underrun protective devices (RUPDs) and their installation; rear underrun protection (RUP) |
Regulation (EC) No 661/2009 UN Regulation No 58 |
|
6A |
Vehicle access and manoeuvrability (steps, running boards and handholds) |
Regulation (EC) No 661/2009 Regulation (EU) No 130/2012 |
|
6B |
Door latches and door retention components |
Regulation (EC) No 661/2009 UN Regulation No 11 |
|
8A |
Devices for indirect vision and their installation |
Regulation (EC) No 661/2009 UN Regulation No 46 |
|
12A |
Interior fittings |
Regulation (EC) No 661/2009 UN Regulation No 21 |
|
16A |
External projections |
Regulation (EC) No 661/2009 UN Regulation No 26 |
|
20A |
Installation of lighting and light-signalling devices on vehicles |
Regulation (EC) No 661/2009 UN Regulation No 48 |
|
27A |
Towing device |
Regulation (EC) No 661/2009 Regulation (EU) No 1005/2010 |
|
32A |
Forward field of vision |
Regulation (EC) No 661/2009 UN Regulation No 125 |
|
35A |
Windscreen wiper and washer systems |
Regulation (EC) No 661/2009 Regulation (EU) No 1008/2010 |
|
37A |
Wheel guards |
Regulation (EC) No 661/2009 Regulation (EU) No 1009/2010 |
|
42A |
Lateral protection of goods vehicles |
Regulation (EC) No 661/2009 UN Regulation No 73 |
|
48A |
Masses and dimensions |
Regulation (EC) No 661/2009 Regulation (EU) No 1230/2012 |
|
49A |
Commercial vehicles with regard to their external projections forward of the cab's rear panel |
Regulation (EC) No 661/2009 UN Regulation No 61 |
|
50A |
Mechanical coupling components of combinations of vehicles |
Regulation (EC) No 661/2009 UN Regulation No 55 |
|
50B |
Close-coupling device (CCD); fitting of an approved type of CCD |
Regulation (EC) No 661/2009 UN Regulation No 102 |
|
52A |
M2 and M3 vehicles |
Regulation (EC) No 661/2009 UN Regulation No 107 |
|
52B |
Strength of the superstructure of large passenger vehicles |
Regulation (EC) No 661/2009 UN Regulation No 66 |
|
57A |
Front underrun protective devices (FUPDs) and their installation; front underrun protection (FUP) |
Regulation (EC) No 661/2009 UN Regulation No 93 |
Appendix 1
General conditions for the use of virtual testing methods
1. Virtual test pattern
The following scheme shall be used as basis structure for describing and conducting virtual testing:
purpose;
structure model;
boundary conditions;
load assumptions;
calculation;
assessment;
documentation.
2. Fundamentals of computer simulation and calculation
2.1. Mathematical model
The mathematical model shall be supplied by the manufacturer. It shall reflect the complexity of the structure of the vehicle, system, component or separate technical unit to be tested in relation to the requirements of the relevant regulatory act and its boundary conditions.
The same provisions shall apply for testing components or separate technical units independently from the vehicle.
2.2. Validation process of the mathematical model
The mathematical model shall be validated against the actual test conditions.
To that effect a physical test shall be conducted to compare the results obtained when using the mathematical model with the results of a physical test. Comparability of the test results shall be proven. The manufacturer or the technical service shall draft a validation report and submit it to the approval authority.
Any change to the mathematical model or to the software that is likely to invalidate the validation report shall be brought to the attention of the approval authority, which may require that a new validation process is conducted.
The flow chart of the validation process is shown in Appendix 3.
2.3. Documentation
The manufacturer shall make available to the technical service and document the data and auxiliary tools used for simulation and calculation.
3. Tools and support
The manufacturer shall supply the technical service at its request with the necessary tools to conduct the virtual testing, including appropriate software, or provide that technical service access to these tools.
The manufacturer shall also provide appropriate support to the technical service.
The access and support provided by the manufacturer to a technical service does not exempt the technical service from its obligations regarding the skills of its personnel, the payment of licence rights and confidentiality.
Appendix 2
Specific conditions for the use of virtual testing methods
1. List of regulatory acts
|
|
Regulatory act reference |
Annex and paragraphs |
Specific conditions |
|
3B |
Regulation (EC) No 661/2009 UN Regulation No 58 |
Paragraphs 2.3, 7.3. and 25.6 of UN Regulation No 58. |
Dimensions and resistance to forces. |
|
6A |
Regulation (EC) No 661/2009 Regulation (EU) No 130/2012 |
Annex II, Part 1 and 2 of Regulation (EU) No 130/2012. |
Dimensions of steps, running boards and handholds. |
|
6B |
Regulation (EC) No 661/2009 UN Regulation No 11 |
Annex 3 of UN Regulation No 11. Annex 4, paragraph 2.1. of UN Regulation No 11. Annex 5 of UN Regulation No 11. |
Tensile strength tests and resistance of latches to acceleration. |
|
8A |
Regulation (EC) No 661/2009 UN Regulation No 46 |
Paragraph 15.2.4. of UN Regulation No 46. |
Prescribed fields of vision of rear-view mirrors. |
|
12A |
Regulation (EC) No 661/2009 UN Regulation No 21 |
(a) Paragraphs 5. to 5.7. of UN Regulation No 21. |
(a) Measurement of all radii of curvature and of all projections except for those requirements where a force has to be applied in order to check compliance with the provisions. |
|
(b) Paragraph 2.3. of UN Regulation No 21. |
(b) Determination of the head-impact zone. |
||
|
16A |
Regulation (EC) No 661/2009 UN Regulation No 26 |
Paragraph 5.2.4. of UN Regulation No 26 All provisions in paragraphs 5 (General requirements) and 6 (Particular requirements) of UN Regulation No 26. |
Measurement of all radii of curvature and of all projections except for those requirements where a force has to be applied in order to check compliance with the provisions. |
|
20A |
Regulation (EC) No 661/2009 UN Regulation No 48 |
Paragraph 6. (Individual specifications), and Annexes 4, 5 and 6 to UN Regulation No 48. |
The test drive provided for in paragraph 6.22.9.2.2 shall be performed on a real vehicle. |
|
27A |
Regulation (EC) No 661/2009 Regulation (EU) No 1005/2010 |
Annex II, point 1.2. of Regulation (EU) No 1005/2010. |
Tractive and compressive static force. |
|
32A |
Regulation (EC) No 661/2009 UN Regulation No 125 |
Paragraph 5 (Specifications) of UN Regulation No 125. |
Obstructions and field of vision. |
|
35A |
Regulation (EC) No 661/2009 Regulation (EU) No 1008/2010 |
Annex III, points 1.1.2. and 1.1.3. of Regulation (EU) No 1008/2010. |
Determination of the swept area only. |
|
37A |
Regulation (EC) No 661/2009 Regulation (EU) No 1009/2010 |
Annex II, point 2. of Regulation (EU) No 1009/2010. |
Verification of the dimensional requirements. |
|
42A |
Regulation (EC) No 661/2009 UN Regulation No 73 |
Paragraph 12.10 of UN Regulation No 73. |
Resistance under a horizontal force and deflection measurement. |
|
48A |
Regulation (EC) No 661/2009 Regulation (EU) No 1230/2012 |
(a) Annex I, Part B, points 7 and 8 of Regulation (EU) No 1230/2012. |
(a) Check of compliance with the manoeuvrability requirements including manoeuvrability of vehicles fitted with lift- or loadable axles. |
|
(b) Annex I, Part C, points 6 and 7 of Regulation (EU) No 1230/2012. |
(b) Measurement of the maximum rear swing-out. |
||
|
49A |
Regulation (EC) No 661/2009 UN Regulation No 61 |
Paragraphs 5 and 6 of UN Regulation No 61. |
Measurement of all radii of curvature and of all projections except for those requirements where a force has to be applied in order to check compliance with the provisions. |
|
50A |
Regulation (EC) No 661/2009 UN Regulation No 55 |
(a) Annex 5 ‘Requirements for mechanical coupling devices’ of UN Regulation No 55. |
(a) All provisions of paragraphs 1 to 8 included. |
|
(b) Annex 6, paragraph 1.1. of UN Regulation No 55. |
(b) Strength tests on mechanicals couplings of simple design may be replaced by virtual tests. |
||
|
(c) Annex 6, paragraph 3 of UN Regulation No 55. |
(c) Paragraphs 3.6.1. (Strength test), 3.6.2. (Resistance to buckling) and 3.6.3. (Resistance to bending moment) only. |
||
|
52A |
Regulation (EC) No 661/2009 UN Regulation No 107 |
Annex 3 of UN Regulation No 107. |
Paragraph 7.4.5. (calculation method). |
|
52B |
Regulation (EC) No 661/2009 UN Regulation No 66 |
Annex 9 of UN Regulation No 66. |
Computer simulation of rollover test on complete vehicle as an equivalent approval method. |
|
57A |
Regulation (EC) No 661/2009 UN Regulation No 93 |
Annex 5, paragraph 3 of UN Regulation No 93. |
Resistance under a horizontal force and deflection measurement. |
Appendix 3
Validation process
ANNEX IX
PROCEDURES TO BE FOLLOWED DURING MULTI-STAGE TYPE-APPROVAL
1. Obligations of manufacturers
|
1.1. |
The satisfactory operation of the multi-stage type-approval requires joint action by all the manufacturers concerned. To that end approval authorities must ensure, before granting first and subsequent stage type-approvals, that suitable arrangements exist between the relevant manufacturers for the supply and interchange of documents and information, so that the completed type of vehicle meets the technical requirements of all the relevant regulatory acts listed in Annex II. Such information must include details of relevant system, component and separate technical unit type-approvals and of vehicle parts that form part of the incomplete vehicle but have not yet been type-approved. |
|
1.2. |
Each manufacturer involved in a multi-stage type-approval shall be responsible for the approval and conformity of production of all systems, components or separate technical units manufactured or added by that manufacturer to the previously built stage. The manufacturer of the subsequent stage shall not be responsible for objects that have been approved in an earlier stage, except where that manufacturer modifies relevant parts to such an extent that the previously granted type-approval becomes invalid. |
2. Obligations of approval authorities
|
2.1. |
The approval authority shall:
(a)
verify that all EU type-approval certificates issued pursuant to the regulatory acts that are applicable for vehicle type-approval cover the type of vehicle at its state of completion and correspond to the prescribed requirements;
(b)
ensure that all the relevant data, taking account of the state of completion of the vehicle, is included in the information folder;
(c)
by reference to the documentation ensure that the vehicle specification(s) and data contained in the information folder are included in the data in the information packages and in the EU type-approval certificates issued in accordance with the relevant regulatory acts; and in the case of a completed vehicle, where an item number of the information folder is not included in the information package of any of the regulatory acts, confirm that the relevant part or characteristic conforms to the particulars in the information folder;
(d)
on a selected sample of vehicles from the type to be approved carry out or arrange to be carried out inspections of vehicle parts and systems to verify that the vehicle(s) is/are built in accordance with the relevant data contained in the authenticated information package in accordance with all relevant regulatory acts; and
(e)
where required carry out, or arrange to be carried out, relevant installation checks for separate technical units. |
|
2.2. |
The number of vehicles to be inspected for the purposes of point 2.1 (d) shall be sufficient to permit the proper control of the various combinations to be EU type-approved according to the state of completion of the vehicle and the following criteria:
—
engine;
—
gearbox;
—
powered axles (number, position, interconnection);
—
steered axles (number and position);
—
body styles;
—
number of doors;
—
hand of drive;
—
number of seats;
—
level of equipment.
|
3. Applicable requirements
|
3.1. |
Multi-stage type-approvals shall be granted on the basis of the state of completion of the type of vehicle and shall incorporate all type-approvals granted at earlier stages. |
|
3.2. |
For the whole-vehicle type-approval, this Regulation (in particular the requirements of Annex I and the particular regulatory acts listed in Annex II) shall apply in the same manner as if the approval would have been granted (or extended) to the manufacturer of the base vehicle.
|
|
3.3. |
Subject to the agreement of the approval authority, a whole-vehicle type-approval granted to the manufacturer of the subsequent stage of completion of the vehicle does not need to be extended or revised where an extension given at the previous stage vehicle does not affect the subsequent stage or the technical data of the vehicle. However, the type-approval number including the extension of the previous stage(s) vehicle shall be copied in the certificate of conformity of the subsequent stage vehicle. |
|
3.4. |
Where the cargo area of a complete or completed vehicle of category N or O is modified by another manufacturer for the addition of removable fittings to store and secure the cargo (for example, load space lining, storage racks and roof racks), such items can be treated as part of the pay-mass and a type-approval is not needed, provided both of the following conditions are met:
(a)
the modifications do not affect the vehicle's type-approval in any way, other than an increase of the actual mass of the vehicle;
(b)
the added fittings can be removed without using special tools. |
4. Identification of the vehicle
|
4.1. |
The VIN, prescribed by Regulation (EU) No 19/2011, shall be retained during all the subsequent stages of the type-approval to ensure the traceability of the process. |
|
4.2. |
At the second and subsequent stages, in addition to the statutory plate prescribed by Regulation (EU) No 19/2011, each manufacturer shall affix to the vehicle an additional plate the model of which is shown in the Appendix to this Annex. This plate shall be firmly attached, in a conspicuous and readily accessible position on a part not subject to replacement in use. It shall clearly and indelibly show the following information in the order listed:
—
the name of the manufacturer;
—
sections 1, 3 and 4 of the EU type-approval number;
—
the stage of approval;
—
the VIN of the base vehicle;
—
the technically permissible maximum laden mass of the vehicle where the value has changed during the current stage of approval;
—
the technically permissible maximum laden mass of the combination (where the value has changed during the current stage of approval and where the vehicle is permitted to tow a trailer). ‘0’ shall be used if the vehicle is not permitted to tow a trailer;
—
the technically permissible maximum mass on each axle, listed in order from front to rear where the value has changed during the current stage of approval;
—
in the case of a semi-trailer or centre axle trailer, the technically permissible maximum mass at the coupling point where the value has changed during the current stage of approval.
Unless otherwise provided for in point 4.1 and this point the additional plate shall comply with the requirements set out in Annex I and Annex II to Regulation (EU) No 19/2011. |
Appendix
Model of the manufacturer's additional plate
The example below is given as a guide only.
MANUFACTURER'S NAME (stage 3)
e2*201X/XX*2609
Stage 3
WD9VD58D98D234560
1 500 kg
2 500 kg
1 – 700 kg
2 – 810 kg
ANNEX X
ACCESS TO VEHICLE OBD INFORMATION AND VEHICLE REPAIR AND MAINTENANCE INFORMATION
1. Introduction
This Annex lays down technical requirements for the access to vehicle OBD information and vehicle repair and maintenance information.
2. Access to vehicle OBD information and vehicle repair and maintenance information
|
2.1. |
A manufacturer shall put in place the necessary arrangements and procedures, in accordance with Article 61, to ensure that vehicle OBD information and vehicle repair and maintenance information is accessible through websites using a standardised format in a readily accessible and prompt manner, and in a manner which is non-discriminatory compared to the provisions given or access granted to authorised dealers and repairers. |
|
2.2. |
An approval authority shall only grant type-approval after receiving from the manufacturer a certificate on access to vehicle OBD information and vehicle repair and maintenance information. |
|
2.3. |
The certificate on access to vehicle OBD information and vehicle repair and maintenance information shall serve as the proof of compliance with Article 64. |
|
2.4. |
The certificate on access to vehicle OBD information and vehicle repair and maintenance information shall be drawn up in accordance with the model set out in Appendix 1. |
|
2.5. |
The vehicle OBD information and vehicle repair and maintenance information shall include the following:
2.5.1.
an unequivocal identification of the vehicle, system, component or separate technical unit for which the manufacturer is responsible;
2.5.2.
service handbooks, including service and maintenance records;
2.5.3.
technical manuals;
2.5.4.
component and diagnosis information (such as minimum and maximum theoretical values for measurements);
2.5.5.
wiring diagrams;
2.5.6.
diagnostic trouble codes, including manufacturer specific codes;
2.5.7.
the software calibration identification number applicable to a type of vehicle;
2.5.8.
information provided concerning, and delivered by means of, proprietary tools and equipment;
2.5.9.
data record information and two-directional monitoring and test data;
2.5.10.
standard work units or time periods for repair and maintenance tasks if they are made available to authorised dealers and repairers of the manufacturer either directly or through a third party;
2.5.11.
in case of multi-stage type-approval, the information required under point 3, and all other information necessary to comply with the requirements set out in Article 61. |
|
2.6. |
The manufacturer shall make available to interested parties the following information:
2.6.1.
relevant information to enable the development of replacement components that are critical to the correct functioning of the OBD system;
2.6.2.
information to enable the development of generic diagnostic tools. |
|
2.7. |
For the purposes of point 2.6.1., the development of replacement components shall not be restricted by any of the following:
2.7.1.
the unavailability of pertinent information;
2.7.2.
the technical requirements relating to malfunction indication strategies if the OBD thresholds are exceeded or if the OBD system is unable to fulfil the basic OBD monitoring requirements of this Regulation;
2.7.3.
specific modifications to the handling of OBD information to deal independently with vehicle operation on petrol or on gas;
2.7.4.
the type-approval of gas-fuelled vehicles that contain a limited number of minor deficiencies. |
|
2.8. |
For the purposes of point 2.6.2, where manufacturers use diagnostic and test tools in accordance with ISO 22900 – Modular vehicle communication interface (MVCI) – and ISO 22901 – Open diagnostic data exchange (ODX) in their franchised networks –, the ODX files shall be accessible to independent operators via the website of the manufacturer. |
|
2.9. |
For the purpose of vehicle OBD, diagnostics, repair and maintenance, the direct vehicle data stream shall be made available through the serial data port on the standardised data link connector specified in paragraph 6.5.1.4 of Appendix 1 of Annex 11 to UN Regulation No 83 and paragraph 4.7.3 of Annex 9B to UN Regulation No 49. When the vehicle is in motion, the data shall only be made available for read-only functions. |
3. Multi-stage type-approval
|
3.1. |
In the case of a multi-stage type-approval, the final manufacturer shall be responsible for providing access to vehicle OBD information and vehicle repair and maintenance information regarding its own manufacturing stage(s) and the link to the previous stage(s). |
|
3.2. |
In addition, the final manufacturer shall on its website provide independent operators with the following information:
3.2.1.
the website address of the manufacturer(s) responsible for the previous stage(s);
3.2.2.
the name and address of all the manufacturers responsible for the previous stage(s);
3.2.3.
the type-approval number(s) of the previous stage(s);
3.2.4.
the engine number. |
|
3.3. |
Each manufacturer responsible for a particular stage or stages of type-approval shall be responsible for providing through his website access to vehicle OBD and vehicle repair and maintenance information regarding the stage(s) of type-approval for which he is responsible and the link to the previous stage(s). |
|
3.4. |
The manufacturer responsible for a particular stage or stages of type-approval shall provide the following information to the manufacturer responsible for the next stage:
3.4.1.
the certificate of conformity relating to the stage(s) for which he is responsible;
3.4.2.
the certificate on access to vehicle OBD information and vehicle repair and maintenance information, including its annexes;
3.4.3.
the type-approval number corresponding to the stage(s) for which he is responsible;
3.4.4.
the documents referred to in points 3.4.1, 3.4.2 and 3.4.3 as provided by the manufacturer(s) involved in the previous stage(s). |
|
3.5. |
Each manufacturer shall authorise the manufacturer responsible for the next stage to pass the documents to the manufacturers responsible for any subsequent stages and the final stage. |
|
3.6. |
In addition, on a contractual basis, the manufacturer responsible for a particular stage or stages of type-approval shall:
3.6.1.
provide the manufacturer responsible for the next stage with access to vehicle OBD information and vehicle repair and maintenance information and interface information corresponding to the particular stage(s) for which he is responsible;
3.6.2.
provide, at the request of a manufacturer responsible for a subsequent stage of type-approval, with access to vehicle OBD information and vehicle repair and maintenance information and interface information corresponding to the particular stage(s) for which he is responsible. |
|
3.7. |
A manufacturer, including a final manufacturer, may only charge fees in accordance with Article 63 concerning the particular stage(s) for which he is responsible. A manufacturer, including a final manufacturer, shall not charge fees for providing information relating to the website address or contact details of any other manufacturer. |
4. Customer adaptations
|
4.1. |
By derogation from point 2, if the number of systems, components or separate technical units subject to a specific customer adaptation is lower than 250 units produced worldwide, repair and maintenance information for the customer adaptation shall be provided in a readily accessible and prompt manner, and in a manner which is non-discriminatory compared to the provisions given or access granted to authorised dealers and repairers. For the servicing and reprogramming of the electronic control units relating to the customer adaptation, the manufacturer shall make the respective proprietary specialist diagnostic tool or test equipment available to independent operators as provided to authorised repairers. The customer adaptations shall be listed on the manufacturer's repair and maintenance information website and mentioned in the certificate on access to vehicle OBD information and vehicle repair and maintenance information at the time of type-approval. |
|
4.2. |
Manufacturers shall make the proprietary specialist diagnostic tool or test equipment to service the customer-adapted systems, components or technical units available to independent operators via sale and rent. |
|
4.3. |
The manufacturer shall mention in the certificate on access to vehicle OBD information and vehicle repair and maintenance information, at the time of type-approval, the customer adaptations for which the obligation under point 2 to provide access to vehicle OBD information and vehicle repair and maintenance information in a standardised format is derogated from and any electronic control unit related to them. Those customer adaptations and any electronic control unit related to them shall also be listed on the manufacturer's repair and maintenance information website. |
5. Small volume manufacturers
|
5.1. |
By derogation from point 2, manufacturers whose worldwide annual production of a type of vehicle, system, component or separate technical unit subject to this Regulation is for vehicles of category M1 and N1 less than 1 000 vehicles or for vehicles of category M2, M3, N2, N3 and O less than 250 units, shall provide access to vehicle repair and maintenance information in a readily accessible and prompt manner, and in a manner that is non-discriminatory compared to the provisions given or access granted to authorised dealers and repairers. |
|
5.2. |
The vehicle, system, component and separate technical unit subject to point 5.1 shall be listed on the manufacturer's repair and maintenance information website. |
|
5.3. |
The approval authority shall inform the Commission of each type-approval granted to small volume manufacturers. |
6. Requirements
|
6.1. |
Vehicle OBD information and vehicle repair and maintenance information available through websites shall follow the relevant common standard referred to in Article 61. Those requiring the right to duplicate or republish the information shall negotiate directly with the manufacturer concerned. Information for training material shall also be available, but may be presented through other media than websites. Information on all parts of the vehicle, with which the vehicle, as identified by the VIN and any additional criteria such as wheelbase, engine output, trim level or options, is equipped by the vehicle manufacturer and that can be replaced by spare parts offered by the vehicle manufacturer to its authorised repairers or dealers or third parties by means of reference to original equipment (OE) parts number, shall be made available, in the form of machine readable and electronically processable datasets, in a database that is easily accessible to independent operators. This database shall comprise the VIN, OE parts numbers, OE naming of the parts, validity attributes (valid-from and valid-to dates), fitting attributes and, where applicable, structuring characteristics. The information on the database shall be updated regularly. If this information is available to authorised dealers, the updates shall include in particular all modifications to individual vehicles after their production. |
|
6.2. |
Access to vehicle security features used by authorised dealers and repairers shall be made available to independent operators under protection of security technology in accordance with the following requirements:
6.2.1.
data shall be exchanged ensuring confidentiality, integrity and protection against replay;
6.2.2.
the standard https//ssl-tls (RFC4346) shall be used;
6.2.3.
security certificates in accordance with international standard ISO 20828 shall be used for mutual authentication of independent operators and manufacturers;
6.2.4.
the independent operator's private key shall be protected by secure hardware. |
|
6.3. |
The Forum on Access to Vehicle Information referred to in Article 66 shall specify the parameters for fulfilling the requirements referred to in point 6.2 in accordance with the state of the art. The independent operator shall be approved and authorised for this purpose on the basis of documents demonstrating that he pursues a legitimate business activity and has not been convicted of any relevant criminal activity. |
|
6.4. |
Reprogramming of control units shall be conducted in accordance with either international standard ISO 22900-2 or SAE J2534 or TMC RP1210B using non-proprietary hardware. For the validation of the compatibility of the manufacturer-specific application and the vehicle communication interfaces (VCI) complying to international standard ISO 22900-2 or SAE J2534 or TMC RP1210B, the manufacturer shall offer either a validation of independently developed VCIs or the information, and loan of any special hardware, required for a VCI manufacturer to conduct such validation himself. The conditions of Article 63(1) shall apply to fees for such validation or information and hardware. |
|
6.5. |
The requirements of point 6.4. shall not apply in the case of reprogramming of speed limitation devices and recording equipment. |
|
6.6. |
All emission-related DTCs shall be consistent with Annex XI to Regulation (EC) No 692/2008 and Annex X to Regulation (EU) No 582/2011. |
|
6.7. |
For access to any vehicle OBD information and vehicle repair and maintenance information other than that relating to secure areas of the vehicle, registration requirements for use of the manufacturer's website by an independent operator shall require only such information as is necessary to confirm how payment for the information is to be made. For information concerning access to secure areas of the vehicle, the independent operator shall present a certificate in accordance with international standard ISO 20828 to identify himself and the organisation to which he belongs and the manufacturer shall respond with his own certificate in accordance with international standard ISO 20828 to confirm to the independent operator that he is accessing a legitimate site of the intended manufacturer. Both parties shall keep a log of any such transactions indicating the vehicles and changes made to them under this provision. |
|
6.8. |
Manufacturers shall indicate in their repair information websites the type-approval number by model. |
|
6.9. |
If the vehicle OBD information and vehicle repair and maintenance information that is available on a manufacturer's website does not contain specific relevant information to permit the proper design and manufacture of alternative fuels retrofit systems, any interested alternative fuels retrofit system manufacturer shall be able to obtain the information required by contacting the manufacturer directly with such a request. Contact details for that purpose shall be clearly indicated on the manufacturer's website and the information shall be provided within 30 days. It shall only be necessary to provide such information for alternative fuels retrofit systems that are subject to UN Regulation No 115 or for alternative fuels retrofit components that form part of systems subject to UN Regulation No 115. In addition, it shall only be necessary to provide such information in response to a request that clearly specifies the exact specification of the vehicle model for which the information is required and that specifically confirms that the information is required for the development of alternative fuels retrofit systems or components subject to UN Regulation No 115. |
7. Requirements for type-approval
|
7.1. |
In order to receive a type-approval, the manufacturer shall submit the filled in certificate, the template of which is provided in Appendix 1. |
|
7.2. |
Where the vehicle OBD information and vehicle repair and maintenance information is not available, or does not conform to the requirements of this Annex, the manufacturer shall provide that information within six months of the date of the type-approval. |
|
7.3. |
The obligation to provide information within the period referred to in point 7.2. shall apply only if, following the type-approval, the vehicle is placed on the market. Where the vehicle is placed on the market more than six months after the type-approval has been granted the information shall be provided on the date on which the vehicle is placed on the market. |
|
7.4. |
On the basis of a completed certificate on access to vehicle OBD information and vehicle repair and maintenance information, the approval authority may presume that the manufacturer has put in place satisfactory arrangements and procedures with regard to access to vehicle OBD information and vehicle repair and maintenance information, provided that no complaint has been made and that the manufacturer provides that certificate within the period referred to in point 7.2. |
Appendix 1
Manufacturer's certificate on access to vehicle OBD information and vehicle repair and maintenance information
ANNEX A
WEBSITE ADDRESSES REFERRED TO IN THIS CERTIFICATE:
ANNEX B
CONTACT DETAILS OF THE MANUFACTURER'S REPRESENTATIVE REFERRED TO IN THIS CERTIFICATE:
ANNEX C
TYPES OF VEHICLE, SYSTEM, COMPONENT OR SEPARATE TECHNICAL UNIT:
Appendix 2
Vehicle OBD information
|
1. |
The vehicle manufacturer shall provide the information required in this Appendix for the purposes of enabling the manufacture of OBD-compatible replacement or service parts and diagnostic tools and test equipment. |
|
2. |
Upon request, the following information shall be made available, on a non-discriminatory basis, to any interested manufacturer of components, diagnostic tools or test equipment:
2.1.
a description of the type and number of the preconditioning cycles used for the original type-approval of the vehicle;
2.2.
a description of the type of the OBD demonstration cycle used for the original type-approval of the vehicle for the component monitored by the OBD system;
2.3.
a comprehensive document describing all sensed components with the strategy for fault detection and MI activation (fixed number of driving cycles or statistical method), including a list of relevant secondary sensed parameters for each component monitored by the OBD system and a list of all OBD output codes and format used (with an explanation of each code and format) associated with individual emission-related power-train components and individual non-emission related components, where monitoring of the component is used to determine MI activation. In particular, in the case of types of vehicles that use a communication link in accordance with ISO 15765-4 ‘Road vehicles — Diagnostics on controller area network (CAN) — Part 4: Requirements for emissions-related systems’, a comprehensive explanation for the data given in service $ 05 Test ID $ 21 to FF and the data given in service $ 06, and a comprehensive explanation for the data given in service $ 06 Test ID $ 00 to FF, for each OBD monitor ID supported, shall be provided. In case other communication protocols standards are used, equivalent comprehensive explanation shall be provided. This information may be provided in the form of a table, with the following column and row headings: Component Fault code; Monitoring strategy; Fault detection criteria; MI activation criteria; Secondary parameters; Preconditioning Demonstration test. Catalyst P0420 Oxygen sensor; 1 and 2 signals; Difference between sensor 1 and sensor 2 signals; 3rd cycle Engine speed; engine load; A/F mode; catalyst temperature; Two Type 1 cycles; Type 1. |
|
3. |
Information required for the manufacturing of diagnostic tools In order to facilitate the provision of generic diagnostic tools for multi-make repairers, vehicle manufacturers shall make available the information referred to in points 3.1, 3.2 and 3.3 through their repair information websites. That information shall include all diagnostic tool functions and all the links to repair information and troubleshooting instructions. The access to the information may be subject to the payment of a reasonable fee. 3.1. Communication protocol information The following information shall be required indexed against vehicle make, model and variant, or another workable definition such as the VIN or the vehicle and systems identification:
3.1.1.
any additional protocol information system necessary to enable complete diagnostics in addition to the standards prescribed in paragraph 4.7.3 of Annex 9B to UN Regulation No 49 and in paragraph 6.5.1.4 of Annex 11 to UN Regulation No 83, including any additional hardware or software protocol information, parameter identification, transfer functions, ‘keep alive’ requirements, or error conditions;
3.1.2.
details of how to obtain and interpret all the fault codes that do not comply with the standards prescribed in paragraph 4.7.3 of Annex 9B to UN Regulation No 49 and in paragraph 6.5.1.4 of Annex 11 to UN Regulation No 83;
3.1.3.
a list of all available live data parameters, including scaling and access information;
3.1.4.
a list of all available functional tests, including device activation or control and the means to implement them;
3.1.5.
details of how to obtain all component and status information, time stamps, pending DTC and freeze frames;
3.1.6.
resetting adaptive learning parameters, variant coding and replacement component setup, and customer preferences;
3.1.7.
Electronic control unit (ECU) identification and variant coding;
3.1.8.
details of how to reset service lights;
3.1.9.
location of diagnostic connector and connector details;
3.1.10.
engine code identification. 3.2. Test and diagnosis of OBD monitored components The following information shall be required:
3.2.1.
a description of tests to confirm the functionality, at the component or in the harness;
3.2.2.
information concerning the test procedure, including test parameters and component information;
3.2.3.
connection details, including minimum and maximum input and output and driving and loading values;
3.2.4.
values to be expected under certain driving conditions, including idling;
3.2.5.
electrical values for the component in its static and dynamic states;
3.2.6.
failure mode values for each of the scenarios;
3.2.7.
failure mode diagnostic sequences, including fault trees and guided diagnostics elimination. 3.3. Data required to perform the repair The following information shall be required:
3.3.1.
ECU and component initialisation (in the event of replacements being fitted);
3.3.2.
initialisation of new or replacement ECU's where relevant using pass-through (re-) programming techniques. |
ANNEX XI
CORRELATION TABLE
1. Regulation (EC) No 715/2007
|
Regulation (EC) No 715/2007 |
This Regulation |
|
Article 1(2) |
Article 86(1), point (2) |
|
Article 3, points (14) and (15) |
Article 3, points (48) and (45) |
|
Article 6 |
Article 61 |
|
Article 7 |
Article 63 |
|
Article 8 |
— |
|
Article 9 |
— |
|
Article 13(2), point (e) |
Article 86(1), point (5) |
2. Regulation (EC) No 595/2009
|
Regulation (EC) No 595/2009 |
This Regulation |
|
Article 1, second paragraph |
Article 87(1), point 2 |
|
Article 3, points (11) and (13) |
Article 3, points (48) and (45) |
|
Article 6 |
Article 61 |
|
Article 11(2), point (e) |
Article 84(3), point (a) |
3. Directive 2007/46/EC
|
Directive 2007/46/EC |
This Regulation |
|
Article 1 |
Article 1(1) |
|
— |
Article 1(2) |
|
Article 2 |
Article 2 |
|
Article 3, point (1) |
— |
|
Article 3, point (2) |
— |
|
Article 3, point (3) |
Article 3, point (1) |
|
Article 3, point (4) |
Article 3, point (3) |
|
Article 3, point (5) |
Article 3, point (2) |
|
Article 3, point (6) |
Article 3, point (6) |
|
Article 3, point (7) |
Article 3, point (8) |
|
Article 3, point (8) |
Article 3, point (9) |
|
Article 3, point (9) |
Article 3, point (10) |
|
Article 3, point (10) |
Article 3, point (11) |
|
Article 3, point (11) |
Article 3, point (16) |
|
Article 3, point (12) |
Article 3, point (17) |
|
Article 3, point (13) |
Article 3, point (15) |
|
Article 3, point (14) |
— |
|
Article 3, point (15) |
— |
|
Article 3, point (16) |
— |
|
Article 3, point (17) |
Article 3, point (32) |
|
Article 3, point (18) |
Article 3, point (24) |
|
Article 3, point (19) |
Article 3, point (25) |
|
Article 3, point (20) |
Article 3, point (26) |
|
Article 3, point (21) |
Article 3, point (27) |
|
Article 3, point (22) |
Article 3, point (28) |
|
Article 3, point (23) |
Article 3, point (18) |
|
Article 3, point (24) |
Article 3, point (19) |
|
Article 3, point (25) |
Article 3, point (20) |
|
Article 3, point (26) |
— |
|
Article 3, point (27) |
Article 3, point (40) |
|
Article 3, point (28) |
Article 3, point (41) |
|
Article 3, point (29) |
Article 3, point (36) |
|
Article 3, point (30) |
— |
|
Article 3, point (31) |
Article 3, point (38) |
|
Article 3, point (32) |
Article 3, point (54) |
|
Article 3, point (33) |
Article 3, point (4) |
|
Article 3, point (34) |
— |
|
Article 3, point (35) |
— |
|
Article 3, point (36) |
Article 3, point (5) |
|
Article 3, points (37) to (40) |
— |
|
— |
Article 3, point (7) |
|
— |
Article 3, points (12), (13) and (14)) |
|
— |
Article 3, points (21), (22) and (23) |
|
— |
Article 3, points (29), (30), (31), (33), (34) and (35) |
|
— |
Article 3, point (37) |
|
— |
Article 3, point (39) |
|
— |
Article 3, points (42) to (53) |
|
— |
Article 3, points (55) to (58) |
|
— |
Article 5(2) and (3) |
|
— |
Article 6(1), third subparagraph, (2) and (3) |
|
— |
Article 7(2), (3) and (4) |
|
Article 4(1) |
— |
|
Article 4(2) |
Article 7(1) |
|
Article 4(3), first subparagraph |
Article 6(4) |
|
Article 4(3), second subparagraph |
Article 6(5), first subparagraph |
|
Article 4(4) |
Article 6(1), first and second subparagraphs |
|
— |
Article 6(5), second subparagraph and (6) to (10) |
|
— |
Article 8 |
|
— |
Article 9 |
|
— |
Article 10 |
|
— |
Article 11 |
|
— |
Article 12 |
|
Article 5(1) |
Article 13(1) and (2), first subparagraph |
|
Article 5(2), first subparagraph |
Article 13(2), second subparagraph |
|
Article 5(2), second subparagraph |
Article 13(3) |
|
Article 5(3) |
Article 13(4), first sentence |
|
— |
Article 13(4), second sentence and (5) to (10) |
|
— |
Article 14 |
|
— |
Article 15 |
|
— |
Article 16 |
|
— |
Article 17 |
|
— |
Article 18 |
|
— |
Article 19 |
|
— |
Article 20 |
|
— |
Article 21 |
|
Article 6(1) |
Article 22(1) |
|
— |
Article 22(2) and (4) |
|
Article 6(2) |
Article 25(1) |
|
Article 6(3) |
— |
|
Article 6(4) |
Article 25(2) |
|
Article 6(5) |
Article 22(5) and (6), and Article 25(3) |
|
Article 6(6) and Article 7(1) |
Article 23 |
|
Article 6(7) and Article 7(3) |
Article 25(4) |
|
Article 6(8) and Article 7(4) |
Article 30(4) |
|
Article 7(2) |
Article 24 |
|
Article 8(1) and (2) |
Article 26(1) and (3) |
|
— |
Article 26(2) and (4) |
|
Article 8(3) |
Article 26(5) |
|
Article 8(4) |
Article 28(2) |
|
Article 8(5) to (8) |
Article 27(1) and (2) |
|
— |
Article 27(3) |
|
Article 9(1) |
Article 5(1) |
|
Article 9(2) |
Article 22(3) |
|
— |
Article 28(1) and (3) |
|
Article 9(3) |
Article 28(4) |
|
Article 9(4) |
Article 28(5) |
|
Article 9(5) |
— |
|
Article 9(6) and (7) |
Article 28(6) and (7) |
|
Article 10(1) and (2) |
Article 29(1) |
|
Article 10(3) |
Article 29(2) |
|
Article 10(4) |
Article 29(3) |
|
Article 11 |
Article 30(1), (2) and (5) to (8) |
|
Article 12(1) |
Article 31(1) |
|
— |
Article 31(2) |
|
Article 12(2), first subparagraph |
Article 31(3) |
|
Article 12(2), second subparagraph |
Article 31(4) |
|
— |
Article 31(5), (6) and (8) |
|
Article 12(3) |
Article 31(7) |
|
— |
Article 32 |
|
Article 13(1) |
Article 33(1) |
|
Article 13(2) |
Article 33(2) |
|
Article 13(3) |
Article 33(3) and (4) |
|
— |
Article 33(5) |
|
Article 14(1) and Article 15(1) |
Article 34(1) |
|
Article 14(2) and Article 15(2) |
Article 34(2) |
|
Article 14(3) and Article 15(3) |
Article 34(3) |
|
Article 14(4) |
Article 34(4) |
|
Article 16(1) and (2) |
Article 27(1) |
|
Article 16(3) |
Article 27(2) |
|
Article 17(1) to (4) |
Article 35(2) to (5) |
|
Article 18(1) and (3) |
Article 36(1) and (4) |
|
— |
Article 36(2) |
|
Article 18(2) |
Article 36(5) |
|
— |
Article 36(6) and (7) |
|
Article 18(4) |
Article 36(8) and (9) |
|
Article 18(5) and (6) |
Article 36(4) |
|
Article 18(7) |
Article 37(2) |
|
Article 18(8) |
Article 36(3) |
|
— |
Article 37(1) and (3) to (9) |
|
— |
Article 38(1) |
|
Article 19(1) and (2) |
Article 38(2) |
|
Article 19(3) |
Article 38(3) |
|
Article 20(1) |
Article 39(1) |
|
Article 20 (2), introductory wording |
Article 39(4) |
|
Article 20 (2), points (a), (b) and (c) |
Article 39(2) |
|
Article 20(3) |
Article 39(5) |
|
Article 20(4), first subparagraph |
Article 39(3) |
|
Article 20(4), second subparagraph |
Article 39(6) |
|
Article 20(4), third subparagraph |
Article 39(7) |
|
Article 20 (5) |
— |
|
Article 21 |
Article 40 |
|
Article 22 |
Article 41 |
|
Article 23(1) |
Article 42(1) |
|
Article 23(2) and (3) |
Article 42(2) |
|
Article 23(4) |
Article 42(3) |
|
Article 23(5) |
Article 42(4) |
|
— |
Article 42(5) |
|
Article 23(6), first subparagraph |
Article 43(1) and (2) |
|
Article 23(6), second subparagraph |
Article 43(3) |
|
Article 23(6), third subparagraph |
Article 43(4) |
|
Article 23(7) |
Article 43(5) |
|
— |
Article 44 |
|
Article 24 |
Articles 45 and 46 |
|
Article 25 |
Article 47 |
|
Article 26(1) |
Article 48(1) |
|
Article 26(2) |
— |
|
Article 26(3) |
Article 48(2) |
|
Article 27 |
Article 49 |
|
Article 28 |
Article 50 |
|
— |
Article 51 |
|
Article 29(1), first subparagraph |
Article 52(1) and (3) |
|
— |
Article 52(2) |
|
— |
Article 52(4) |
|
Article 29(1), second subparagraph |
Article 53(1) and (2) |
|
— |
Article 53(3) and (4) |
|
Article 29(2) |
Article 53(5), first subparagraph |
|
— |
Article 53(5), second subparagraph, (6) and (8) |
|
Article 29(3) |
Article 53(7) |
|
Article 29(4) |
— |
|
Article 30(1) |
Article 53(1) |
|
Article 30(2), first subparagraph |
Article 53(2) |
|
Article 30(2), second subparagraph |
— |
|
Article 30(3) |
Article 54(1) |
|
Article 30(4) |
Article 54(2), (3) and (4), first subparagraph |
|
Article 30(5) |
Article 54(4), second subparagraph |
|
Article 30(6) |
Article 54(5) |
|
Article 31(1) to (4) |
Article 55 |
|
Article 31(5), first subparagraph |
Article 56(1) |
|
Article 31(5), second and third subparagraphs |
Article 56(2) |
|
Article 31(6) and (7) |
— |
|
Article 31(8) |
Article 56(3) |
|
Article 31(9) |
Article 56(4) |
|
— |
Article 56(5) |
|
Article 31(10) |
Article 56(6) |
|
Article 31(11) |
— |
|
Article 31(12), first subparagraph |
Article 56(7) |
|
Article 31(12), second subparagraph |
— |
|
Article 31(13) |
— |
|
Article 32 |
Article 53 |
|
Article 33 |
— |
|
Article 34(1) |
Article 57(1) |
|
Article 34(2) |
Article 57(2) |
|
Article 34(3) and (4) |
— |
|
Article 35 |
Article 58 |
|
Article 36 |
— |
|
Article 37 |
Article 59 |
|
Article 38 |
Article 60 |
|
— |
Article 62 |
|
— |
Article 64 |
|
— |
Article 65 |
|
— |
Article 66 |
|
— |
Article 67 |
|
Article 39 |
Article 82 |
|
Article 40 |
Article 83 |
|
Article 41(1) and (3) |
Article 68(1) |
|
Article 41(2) |
Article 80(1) |
|
Article 41(4) |
Article 70 |
|
Article 41(5) |
Article 68(2) |
|
— |
Article 69(3) and (4) |
|
Article 41(6) |
Article 72(1) |
|
Article 41(7) |
Article 72(2) and (3) |
|
Article 41(8) |
Article 68(5) |
|
— |
Article 69 |
|
— |
Article 71 |
|
Article 42 |
Article 73 |
|
Article 43(1) and (3) |
Article 74(1) |
|
Article 43(2) |
Article 74(2) |
|
Article 43(4) |
Article 75 |
|
Article 43(5) |
Article 74(3) |
|
— |
Article 76 |
|
— |
Article 77 |
|
— |
Article 78 |
|
— |
Article 79 |
|
— |
Article 80(2) and (3) |
|
— |
Article 81 |
|
Article 44 |
Article 89 |
|
Article 45 |
Article 91 |
|
Article 46 |
Article 84 |
|
— |
Article 85 |
|
Article 47 |
Article 90 |
|
Article 48 |
— |
|
Article 49 |
Article 88 |
|
— |
Article 86 |
|
— |
Article 87 |
|
Article 50 |
Article 91 |
|
Article 51 |
— |
|
Annexes I and III |
Article 24(4) |
|
Annex II, part A, points 1 to 1.3.4. |
Article 4 |
|
Annex II, part A, points 2 to 6.2, part B, part C, Appendices 1 and 2 |
Annex I |
|
Annex IV |
Annex II, parts I and II |
|
Annex V, Appendices 1 and 2 |
Annex III |
|
Annex V, Appendix 3 |
Article 30(3) |
|
Annexes VI, VII and VIII |
Article 28(3) |
|
Annex IX |
Article 36(3) |
|
Annex X |
Annex IV |
|
Annex XI |
Annex IV, part III |
|
Annex XII |
Annex V |
|
Annex XIII |
Annex VI |
|
Annex XIV |
— |
|
Annex XV |
Annex VII |
|
Annex XVI |
Annex VIII |
|
Annex XVII |
Annex IX |
|
— |
Annex X |
|
Annex XIX |
— |
|
Annex XX |
— |
|
Annex XXI |
Annex XI |
( 1 ) Regulation (EU) No 167/2013 of the European Parliament and of the Council of 5 February 2013 on the approval and market surveillance of agricultural or forestry vehicles (OJ L 60, 2.3.2013, p. 1).
( 2 ) Regulation (EU) No 168/2013 of the European Parliament and of the Council of 15 January 2013 on the approval and market surveillance of two- or three-wheel vehicles and quadricycles (OJ L 60, 2.3.2013, p. 52).
( 3 ) Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (OJ L 157, 9.6.2006, p. 24).
( 4 ) Council Directive 96/53/EC of 25 July 1996 laying down for certain road vehicles circulating within the Community the maximum authorized dimensions in national and international traffic and the maximum authorized weights in international traffic (OJ L 235, 17.9.1996, p. 59).
( 5 ) Directive 2001/95/EC of the European Parliament and of the Council of 3 December 2001 on general product safety (OJ L 11, 15.1.2002, p. 4).
( 6 ) Commission Regulation (EU) 19/2011 of 11 January 2011 concerning type-approval requirements for the manufacturer's statutory plate and for the vehicle identification number of motor vehicles and their trailers and implementing Regulation (EC) No 661/2009 of the European Parliament and of the Council concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor (OJ L 8, 12.1.2011, p. 1).
( 7 ) Commission Regulation (EC) No 692/2008 of 18 July 2008 implementing and amending Regulation (EC) No 715/2007 of the European Parliament and of the Council on type-approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information (OJ L 199, 28.7.2008, p. 1).
( 8 ) Council Directive 80/181/EEC of 20 December 1979 on the approximation of the laws of the Member States relating to units of measurement and on the repeal of Directive 71/354/EEC (OJ L 39, 15.2.1980, p. 40).
( 9 ) Commission Regulation (EU) 2017/1151 of 1 June 2017 supplementing Regulation (EC) No 715/2007 of the European Parliament and of the Council on type-approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information, amending Directive 2007/46/EC of the European Parliament and of the Council, Commission Regulation (EC) No 692/2008 and Commission Regulation (EU) No 1230/2012 and repealing Commission Regulation (EC) No 692/2008 (OJ L 175, 7.7.2017, p. 1).
( 10 ) Regulation (EU) No 510/2011 of the European Parliament and of the Council of 11 May 2011 setting emission performance standards for new light commercial vehicles as part of the Union's integrated approach to reduce CO2 emissions from light-duty vehicles (OJ L 145, 31.5.2011, p. 1).
( 11 ) Commission Regulation (EU) No 1230/2012 of 12 December 2012 implementing Regulation (EC) No 661/2009 of the European Parliament and of the Council with regard to type-approval requirements for masses and dimensions of motor vehicles and their trailers and amending Directive 2007/46/EC of the European Parliament and of the Council (OJ L 353, 21.12.2012, p. 31).
( 12 ) In the absence of a registration document, the competent authority may refer to available documented evidence of date of manufacture or documented evidence of first purchase.
( 13 ) OJ L 135, 31.5.2018, p. 1.
( 14 ) OJ L 346, 17.12.1997, p. 78.
( 15 ) For subsequent amendments, see UNECE TRANS/WP.29/343.