EUR-Lex Access to European Union law
This document is an excerpt from the EUR-Lex website
Document 02008L0043-20120314
Commission Directive 2008/43/EC of 4 April 2008 setting up, pursuant to Council Directive 93/15/EEC, a system for the identification and traceability of explosives for civil uses (Text with EEA relevance)
Consolidated text: Commission Directive 2008/43/EC of 4 April 2008 setting up, pursuant to Council Directive 93/15/EEC, a system for the identification and traceability of explosives for civil uses (Text with EEA relevance)
Commission Directive 2008/43/EC of 4 April 2008 setting up, pursuant to Council Directive 93/15/EEC, a system for the identification and traceability of explosives for civil uses (Text with EEA relevance)
02008L0043 — EN — 14.03.2012 — 001.001
This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document
|
COMMISSION DIRECTIVE 2008/43/EC of 4 April 2008 setting up, pursuant to Council Directive 93/15/EEC, a system for the identification and traceability of explosives for civil uses (OJ L 094 5.4.2008, p. 8) |
Amended by:
|
|
|
Official Journal |
||
|
No |
page |
date |
||
|
L 50 |
18 |
23.2.2012 |
||
COMMISSION DIRECTIVE 2008/43/EC
of 4 April 2008
setting up, pursuant to Council Directive 93/15/EEC, a system for the identification and traceability of explosives for civil uses
(Text with EEA relevance)
CHAPTER 1
GENERAL PROVISIONS
Article 1
Subject matter
This Directive sets up a harmonised system for the unique identification and traceability of explosives for civil uses.
Article 2
Scope
This Directive shall not apply to the following:
explosives transported and delivered unpackaged or in pump trucks for their direct unloading into the blast-hole;
explosives manufactured at the blasting sites, and that are loaded immediately after being produced (in situ production);
ammunitions;
fuses, which are cord-like non-detonating igniting devices;
safety fuses, which consist of a core of fine grained black powder surrounded by a flexible woven fabric with one or more protective outer coverings and which, when ignited, burn at a predetermined rate without any external explosive effect;
cap-type primers, which consist of a metal or plastic cap containing a small amount of primary explosive mixture that is readily ignited by impact and which serve as igniting elements in small arms cartridges or in percussion primers for propelling charges.
CHAPTER 2
PRODUCT IDENTIFICATION
Article 3
Unique identification
Where an explosive is subject to further manufacturing processes, manufacturers shall not be required to mark the explosive with a new unique identification unless the original unique identification is no longer marked in compliance with Article 4.
Where the manufacturing site is located outside the Community and the manufacturer is not established in the Community, the importer of the explosives concerned shall contact a national authority of the Member State of import in order for the manufacturing site to be attributed a code.
Article 4
Marking and affixation
The unique identification shall be marked on or firmly affixed to the article concerned in a durable way and so as to ensure that it is clearly legible.
Article 5
Cartridged explosives and explosives in sacks
For cartridged explosives and explosives in sacks, the unique identification shall consist of an adhesive label or direct printing on each cartridge or sack. An associated label shall be placed on each case of cartridges.
In addition, undertakings may use a passive inert electronic tag attached to each cartridge or sack and similarly, an associated electronic tag for each case of cartridges.
Article 6
Two-component explosives
For packaged two-component explosives, the unique identification shall consist of an adhesive label or direct printing on each smallest packaging unit containing the two components.
Article 7
Plain detonators
For plain detonators the unique identification shall consist of an adhesive label or direct printing or stamping on the detonator shell. An associated label shall be placed on each case of detonators.
In addition, undertakings may use a passive inert electronic tag attached to each detonator, and an associated tag for each case of detonators.
Article 8
Electric, non-electric and electronic detonators
For electric, non-electric and electronic detonators, the unique identification shall consist either of an adhesive label on the wires or tube, or an adhesive label or direct printing or stamping on the detonator shell. An associated label shall be placed on each case of detonators.
In addition, undertakings may use a passive inert electronic tag attached to each detonator, and an associated tag for each case of detonators.
Article 9
Primers and boosters
For primers other than those referred to in Article 2 and for boosters the unique identification shall consist of an adhesive label or direct printing on such primers and boosters. An associated label shall be placed on each case of such primers and boosters.
In addition, undertakings may use a passive inert electronic tag attached to each such primer and booster, and an associated tag for each case of such primers and boosters.
Article 10
Detonating cords
For detonating cords the unique identification shall consist of an adhesive label or direct printing on the bobbin. The unique identification will be marked every 5 meters on either the external envelope of the cord or the plastic extruded inner layer immediately under the exterior fibre of the cord. An associated label shall be placed on each case of detonating cord.
In addition, undertakings may use a passive inert electronic tag inserted within the cord, and an associated tag for each case of cord.
Article 11
Cans and drums containing explosives
For cans and drums containing explosives, the unique identification shall consist of an adhesive label or direct printing on the can or drum containing the explosives.
In addition, undertakings may use a passive inert electronic tag attached to each can and drum.
Article 12
Copies of the original label
Undertakings may attach adhesive detachable copies of the original label to the explosives for use by their clients. Those copies shall be visibly marked as copies of the original to prevent misuse.
CHAPTER 3
DATA COLLECTION AND RECORD-KEEPING
Article 13
Data collection
Article 14
Obligations of undertakings
Member States shall ensure that the undertakings in the explosives sector fulfil the following:
keeping a record of all identifications of explosives, together with all pertinent information including the type of explosive, the company or person to the custody of whom it was given;
recording the location of each explosive while the explosive is in their possession or custody until it is either transferred to another undertaking or used;
at regular interval testing their data collection system in order to ensure its effectiveness and the quality of the data recorded;
keeping and maintaining the data collected including the unique identifications for the period specified in paragraph 3 of Article 13;
protecting the data collected against accidental or malicious damage or destruction;
providing the competent authorities, upon their request, with the information concerning the origin and location of each explosive during its life cycle and throughout the supply chain;
providing the responsible Member State authorities with the name and contact details of a person able to provide the information described in point (f) outside normal business hours.
For the purpose of point (d), the undertaking shall, in the case of explosives manufactured or imported before the date specified in the second subparagraph of Article 15(1), maintain records in accordance with existing national provisions.
CHAPTER 4
FINAL PROVISIONS
Article 15
Transposition
They shall apply those provisions from 5 April 2013. However, they shall apply the provisions necessary to comply with Article 3(6) and Articles 13 and 14 from 5 April 2015.
When Member States adopt those provisions, they shall contain a reference to this Directive or be accompanied by such a reference on the occasion of their official publication. Member States shall determine how such reference is to be made.
Article 15a
By 31 December 2020, the Commission shall carry out a review to assess whether technical progress has made it possible to revoke the exemptions set out in point 3 of the Annex.
Article 16
Entry into force
This Directive shall enter into force on the third day following that of its publication in the Official Journal of the European Union.
Article 17
This Directive is addressed to the Member States.
ANNEX
The unique identification shall comprise:
a human readable part of the identification containing the following:
the name of the manufacturer;
an alphanumerical code containing:
two letters identifying the Member State (place of production or import onto the Community market, e.g. AT = Austria);
three digits identifying the name of the manufacturing site (attributed by the national authorities);
the unique product code and logistical information designed by the manufacturer;
an electronic readable identification in barcode and/or matrix code format that relates directly to the alphanumerical identification code.
Example:
For articles too small to affix the unique product code and logistical information designed by the manufacturer, the information under 1(b)(i), 1(b)(ii) and 2 shall be considered sufficient.
For articles too small to affix the information under point 1(b)(i) and (ii) and point 2 or where it is technically impossible due to their shape or design to affix a unique identification, a unique identification shall be affixed on each smallest packaging unit.
Each smallest packaging unit shall be closed with a seal.
Each plain detonator or booster falling under the exemption set out in the second paragraph shall be marked in a durable way so as to ensure that it is clearly legible with the information under point 1(b)(i) and (ii). The number of plain detonators and boosters contained shall be printed on the smallest packaging unit.
Each detonating cord falling under the exemption set out in the second paragraph shall be marked with the unique identification on the reel or spool and, where applicable, on the smallest packaging unit.
( 1 ) OJ L 121, 15.5.1993, p. 20. Directive as amended by Regulation (EC) No 1882/2003 of the European Parliament and of the Council (OJ L 284, 31.10.2003, p. 1).