(1)

In accordance with Article 7 of Directive 2006/42/EC machinery manufactured in conformity with a harmonised standard, the reference to which has been published in the Official Journal of the European Union, is to be presumed to comply with the essential health and safety requirements covered by such a harmonised standard.

(2)

By letter M/396 of 19 December 2006, the Commission made a request to the European Committee for Standardisation (CEN) and the European Committee for Electrotechnical Standardisation (Cenelec) (‘the request’) for the drafting, the revision and the completion of the work on harmonised standards in support of Directive 2006/42/EC to take account of changes introduced by that Directive in comparison with Directive 98/37/EC of the European Parliament and of the Council (3).

(3)

On the basis of the request, CEN drafted new harmonised standards EN 1459-5:2020 on safety requirements for attachment interfaces for variable reach trucks, as well as EN 16808:2020 on safety requirements for manual elevators in the petroleum, petrochemical and natural gas industries.

(4)

On the basis of the request, CEN and Cenelec revised existing harmonised standards, the references of which are published in the C series of the Official Journal of the European Union by Commission Communication 2018/C092/01 (4) to adapt them to technological progress. This resulted in the adoption of the following new harmonised standards: EN 12312-7:2020 with specific requirements for aircraft ground support equipment; EN 13586:2020 on access requirements to cranes; EN 15011:2020 on bridge and gantry cranes; EN 15571:2020 on safety requirements for surface finishing machines for natural stone; EN 16564:2020 on requirements for bridge type sawing/milling machines including numerical control; EN 1804-1:2020 on support units and general requirements for hydraulic powered roof supports; EN 1804-2:2020 on power set legs and rams for hydraulic powered roof supports; EN 1804-3:2020 on hydraulic and electro hydraulic control systems for hydraulic powered roof supports; EN 1837:2020 on integral lightning of machines; EN 1974:2020 on safety and hygiene requirements for food processing machinery; EN 81-40:2020 on stairlifts and inclined lifting platforms intended for persons with impaired mobility; EN 1175:2020 on electrical and electronic requirements for industrial trucks; EN 12312-3:2017+A1:2020 on conveyor belt vehicles; EN ISO 16092-2:2020 on safety requirements for mechanical presses; EN ISO 16092-4:2020 on safety requirements for pneumatic presses; EN 16307-1:2020 with supplementary requirements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks; EN 16808:2020 on manual elevators; EN ISO 19085-10:2019/A11:2020 on building site saws; EN ISO 20430:2020 on injection moulding machines; EN IEC 62841-2-6:2020 on particular requirements for hand-held hammers with an amendment in EN IEC 62841-2-6:2020/A11:2020; as well as EN ISO 11553-1:2020 on laser safety requirements with an amendment in EN ISO 11553-1:2020/A11:2020.

(5)

In addition, on the basis of the request, CEN and Cenelec revised EN 12999:2011+A2:2018, the reference of which is included in Annex I to Commission Implementing Decision (EU) 2019/436 (5), to EN 12999:2020 on loader cranes in order to adapt it to technological progress.

(6)

CEN and Cenelec also amended EN 16851:2017 on light crane systems and EN 16486:2014 on compactors, the references of which have been published by Communication 2018/C092/01, respectively to EN 16851:2017+A1:2020 on light crane systems and 16486:2014+A1:2020 on compactors.

(7)

The Commission together with CEN and Cenelec has assessed whether the standards drafted, revised and amended by CEN and Cenelec comply with the request.

(8)

The harmonised standards drafted, revised and amended by CEN and Cenelec on the basis of the request satisfy the safety requirements which they aim to cover and which are set out in Directive 2006/42/EC. It is therefore appropriate to publish the references of those standards in the Official Journal of the European Union, together with references of any relevant amending or correcting standards thereto.

(9)

The reference of standard EN 474-1:2006+A4:2013 was published in the Official Journal of the European Union with a restriction by Commission Implementing Decision (EU) 2015/27 (6) that excluded the presumption of conformity provided by the standard in relationship to the essential health and safety requirements 1.2.2 and 3.2.1 of Annex I to Directive 2006/42/EC.

(10)

Standard EN 474-1:2006+A4:2013 is withdrawn as of 19 September 2020, as provided for in Implementing Decision (EU) 2019/436. It is therefore appropriate to repeal Implementing Decision (EU) 2015/27.

(11)

CEN improved the standard in the version EN 474-1:2006+A5:2018. However, the new version failed to address the visibility concerns caused by the interplay of EN 474-1:2006+A5:2018 with part 5 of EN 474 series that cover specific requirements for hydraulic excavators. Therefore, standard EN 474-1:2006+A5:2018 did not fully meet the essential health and safety requirements set out in points 1.2.2 and 3.2.1 of Annex I to Directive 2006/42/EC. The harmonised standard was published with a new restriction in relation to its application with EN 474-5:2006+A3:2013 requirements for hydraulic excavators in the Official Journal of the European Union by Implementing Decision (EU) 2019/436.

(12)

CEN continued to improve EN 474-1 and presented an amended version of the harmonised standard EN 474-1:2006+A6:2019. The Commission together with CEN and Cenelec has assessed whether the standards EN 474-1:2006+A6:2019 meet the essential health and safety requirements set out in points 1.2.2 and 3.2.1 of Annex I to Directive 2006/42/EC and concluded that the restriction in relation to the visibility concerns of the standard could be lifted.

(13)

However, while examining standard EN 474-1 new concerns were raised by the representatives of the committee established by Article 22 of Directive 2006/42/EC, regarding the quick coupling mechanism foreseen in annex B.2 of the standard that allows for the attachment of different tools to earth-moving machines. In particular, a high number of serious injuries and fatalities were recorded by the Member States due to the incorrect locking of tools and the absence of an active warning system or active monitoring system for the operator when engaging the machine with incorrectly attached tools such as backhoe buckets, grabs, vibratory plates. The number of accidents are particularly pronounced for certain machines such as excavators that change regularly different powered tools on a daily basis.

(14)

Having examined EN 474-1:2006+A6:2019, the Commission concluded that the standard fails to meet the essential healthy and safety requirement set out in points 1.2.2 and 3.2.1 of Annex I to Directive 2006/42/EC, namely the requirement of safety integration and that the driver can operate the machinery and its tools in their foreseeable conditions of use, in complete safety for the driver and the exposed persons. EN 474-1:2006+A6:2019 should therefore be published in the Official Journal of the European Union with restriction when applied in combination with parts EN 474-4:2006+A2:2012 requirements for backhoe loaders and EN 474-5:2006+A3:2013 requirements for hydraulic excavators.

(15)

Harmonised standard EN 62841-4-1:2020 on particular requirements for hand-held chain saws introduced significant changes to the specifications set out in harmonised standard EN 60745-2-13:2009. Hand-held chain saws, covered by EN 62841-4-1:2020 and EN 60745-2-13:2009, are a machinery listed in Annex IV to Directive 2006/42/EC that need to follow a stricter certification procedure involving a notified body in the absence of a harmonised standard covering all of the relevant essential health and safety requirements. Considering that the design of chain saws covered by harmonised standard EN 62841-4-1:2020 needs to be significantly modified and that harmonised standard EN 60745-2-13:2009 ceases to provide a presumption of conformity after 3 September 2022, a number of manufacturers may not be in a position to meet that deadline. It is therefore appropriate to exceptionally postpone the date of withdrawal of harmonised standard EN 60745-2-13:2009 for an additional 8 months. The entry concerning the harmonised standard EN 60745-2-13:2019 in Annex III to Implementing Decision (EU) 2019/436 should therefore be amended accordingly.

(16)

Reference of harmonised standard EN ISO 3743-2:2019 on methods for special reverberation test rooms was included in Annex I to Implementing Decision (EU) 2019/436 by Commission Implementing Decision 2021/377 (7). However, the previous version of that standard, EN ISO 3743-2:2009 was published by Communication 2018/C092/01, and has not been withdrawn. Considering that standard EN ISO 3743-2:2009 no longer represents the state of the art, it is appropriate to withdraw the reference of that standard from the Official Journal of European Union. In order to give manufacturers sufficient time to prepare for applying standard EN ISO 3743-2:2019, it is necessary to defer the withdrawal of EN ISO 3743-2:2009.

(17)

Implementing Decision (EU) 2019/436 provides in Annex I the references of harmonised standards conferring a presumption of conformity with Directive 2006/42/EC and provides in Annex II the references of harmonised standards conferring a presumption of conformity with restrictions. In order to ensure that the references of harmonised standards drafted in support of Directive 2006/42/EC are listed in one act, the references of the standards that are replaced, revised or amended by CEN and Cenelec should be included in Implementing Decision (EU) 2019/436.

(18)

Annex III to Implementing Decision (EU) 2019/436 lists the references of harmonised standards in support of Directive 2006/42/EC that are withdrawn from the C series of the Official Journal of the European Union as from the dates set out in that Annex.

(19)

As the result of the work by CEN and Cenelec on the basis of the Request, the following harmonised standards published in the C series of the Official Journal of the European Union have been replaced, revised or amended: EN 12312-7:2005+A1:2009; EN 13155:2003+A2:2009; EN 13586:2004+A1:2008; EN 15011:2011+A1:2014; EN 15571:2014; EN 15746-2:2010+A1:2011; EN 1804-1:2001+A1:2010; EN 1804-2:2001+A1:2010; EN 1804-3:2006+A1:2010; EN 1837:1999+A1:2009; EN 1974:1998+A1:2009; EN 60745-2-6:2010; EN IEC 62841-2-6:2020; EN ISO 11553-1:2008; EN ISO 11553-1:2020; EN 1175-1:1998+A1:2010; EN 1175-2:1998+A1:2010; EN 1175-3:1998+A1:2010; EN 12312-3:2017; EN 13411-1:2002+A1:2008; EN 13411-2:2001+A1:2008; EN 13411-3:2004+A1:2008; EN 13411-4:2011; EN 13411-5:2003+A1:2008; EN 13411-6:2004+A1:2008; EN 13411-7:2006+A1:2008; EN 13411-8:2011; EN 16307-1:2013+A1:2015; EN 16486:2014; EN 201:2009; and EN 81-40:2008. It is therefore necessary to withdraw the references of those standards from the Official Journal of the European Union by including those references in Annex III to Implementing Decision (EU) 2019/436.

(20)

It is also necessary to withdraw the reference of harmonised standard EN 12999:2011+A2:2018 published by Implementing Decision (EU) 2019/436, given that the standard has been revised. It is therefore appropriate to delete the reference from Annex I to that Implementing Decision.

(21)

In order to give manufacturers sufficient time to prepare for application of the new, revised or amended standards, it is necessary to defer the withdrawal of the references of harmonised standards EN 12999:2011+A2:2018, EN 1175-1:1998+A1:2010, EN 1175-2:1998+A1:2010, EN 1175-3:1998+A1:2010, EN 12312-3:2017, EN 12312-7:2005+A1:2009, EN 13411-1:2002+A1:2008, EN 13411-2:2001+A1:2008, EN 13411-3:2004+A1:2008, EN 13411-4:2011, EN 13411-5:2003+A1:2008, EN 13411-6:2004+A1:2008, EN 13411-7:2006+A1:2008, EN 13411-8:2011, EN 13586:2004+A1:2008, EN 15011:2011+A1:2014, EN 16307-1:2013+A1:2015, EN 16486:2014, EN 16851:2017, EN 1804-1:2001+A1:2010, EN 1804-2:2001+A1:2010, EN 1804-3:2006+A1:2010, EN 1837:1999+A1:2009, EN 1974:1998+A1:2009, EN 201:2009, EN 60745-2-6:2010, EN 81-40:2008, EN ISO 11553-1:2008, and EN ISO 3743-2:2009.

(22)

Implementing Decision (EU) 2019/436 should therefore be amended accordingly.

(23)

Compliance with a harmonised standard confers a presumption of conformity with the corresponding essential requirements set out in Union harmonisation legislation from the date of publication of the reference of such standard in the Official Journal of the European Union. This Decision should therefore enter into force on the date of its publication,