This document is an excerpt from the EUR-Lex website
Document 02023R0753-20251009
Commission Implementing Regulation (EU) 2023/753 of 12 April 2023 granting a Union authorisation for the biocidal product family C(M)IT/MIT formulations (Text with EEA relevance)
Consolidated text: Commission Implementing Regulation (EU) 2023/753 of 12 April 2023 granting a Union authorisation for the biocidal product family C(M)IT/MIT formulations (Text with EEA relevance)
Commission Implementing Regulation (EU) 2023/753 of 12 April 2023 granting a Union authorisation for the biocidal product family C(M)IT/MIT formulations (Text with EEA relevance)
02023R0753 — EN — 09.10.2025 — 001.001
This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links embedded in this document
|
COMMISSION IMPLEMENTING REGULATION (EU) 2023/753 of 12 April 2023 granting a Union authorisation for the biocidal product family “C(M)IT/MIT formulations” (OJ L 100 13.4.2023, p. 48) |
Amended by:
|
|
|
Official Journal |
||
|
No |
page |
date |
||
|
COMMISSION IMPLEMENTING REGULATION (EU) 2025/1800 of 10 September 2025 |
L 1800 |
1 |
19.9.2025 |
|
COMMISSION IMPLEMENTING REGULATION (EU) 2023/753
of 12 April 2023
granting a Union authorisation for the biocidal product family “C(M)IT/MIT formulations”
(Text with EEA relevance)
Article 1
A Union authorisation with authorisation number EU-0025678-0000 is granted to Solenis Switzerland GmbH for the making available on the market and use of the same biocidal product family “C(M)IT/MIT formulations” in accordance with the summary of the biocidal product characteristics set out in the Annex.
The Union authorisation is valid from 3 May 2023 until 31 August 2032.
Article 2
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
This Regulation shall be binding in its entirety and directly applicable in all Member States.
ANNEX
SUMMARY OF PRODUCT CHARACTERISTICS FOR A BIOCIDAL PRODUCT FAMILY
C(M)IT/MIT formulations
Product type(s)
PT06: Preservatives for products during storage
PT11: Preservatives for liquid-cooling and processing systems
PT12: Slimicides
Authorisation number: EU-0025678-0000
R4BP asset number: EU-0025678-0000
PART I.
FIRST INFORMATION LEVEL
1. ADMINISTRATIVE INFORMATION
1.1. Family name
|
Name |
C(M)IT/MIT formulations |
1.2. Product type(s)
|
Product type(s) |
PT06: Preservatives for products during storage PT11: Preservatives for liquid-cooling and processing systems PT12: Slimicides |
1.3. Authorisation holder
|
Name and address of the authorisation holder |
Name |
Solenis Switzerland GmbH |
|
Address |
Mühlentalstrasse 38 8200 Schaffhausen CH |
|
|
Authorisation number |
|
EU-0025678-0000 |
|
R4BP asset number |
|
EU-0025678-0000 |
|
Date of the authorisation |
|
3 May 2023 |
|
Expiry date of the authorisation |
|
31 August 2032 |
1.4. Manufacturer(s) of the product
|
Name of manufacturer |
Solenis Switzerland GmbH |
|
Address of manufacturer |
Mühlentalstrasse 38 8200 Schaffhausen Switzerland |
|
Location of manufacturing sites |
Solenis Switzerland GmbH site 1 Fütingsweg 20 D-47805 Krefeld Germany Solenis Switzerland GmbH site 2 Wimsey Way, Somercotes DE55 4PA Alfreton United Kingdom of Great Britain and Northern Ireland (the) Solenis Switzerland GmbH site 3 Högastensgatan 18 252 32 Helsingborg Sweden Solenis Switzerland GmbH site 4 AD International B.V. Markweg Zuid 27 4793 ZJ Fijnaart Netherlands (the) |
|
Name of manufacturer |
Diversey UK Production Ltd |
|
Address of manufacturer |
Cotes Park Industrial Estate, Somercotes DE55 4PA Alfreton United Kingdom of Great Britain and Northern Ireland (the) |
|
Location of manufacturing sites |
Diversey UK Production Ltd Cotes Park Industrial Estate, Somercotes, DE55 4PA Alfreton United Kingdom of Great Britain and Northern Ireland (the) |
|
Name of manufacturer |
Diversey Italy Production Srl |
|
Address of manufacturer |
Strada Statale 235 26010 Bagnolo Cremasco (CR) Italy |
|
Location of manufacturing sites |
Diversey Italy Production Srl Strada Statale 235 26010 Bagnolo Cremasco (CR) Italy |
|
Name of manufacturer |
Diversey España Production S.L.U |
|
Address of manufacturer |
Avenida Conde Duque 5, 7 y 9, Poligono Industrial La Postura 28343 Valdemoro (Madrid) Spain |
|
Location of manufacturing sites |
Diversey España Production S.L.U Avenida Conde Duque 5, 7 y 9, Poligono Industrial La Postura 28343 Valdemoro (Madrid) Spain |
|
Name of manufacturer |
Diversey Netherlands Production BV |
|
Address of manufacturer |
Rembrandtlaan 414 7545ZW Enschede Netherlands (the) |
|
Location of manufacturing sites |
Diversey Netherlands Production BV Rembrandtlaan 414 7545ZW Enschede Netherlands (the) |
|
Name of manufacturer |
Diversey Germany Production oHG |
|
Address of manufacturer |
Morschheimer Strasse 12 67292 Kirchheimbolanden Germany |
|
Location of manufacturing sites |
Diversey Germany Production oHG Morschheimer Strasse 12 67292 Kirchheimbolanden Germany |
1.5. Manufacturer(s) of the active substance(s)
|
Active substance |
C(M)IT/MIT (3:1) |
|
Name of manufacturer |
Specialty Electronic Materials Switzerland GmbH |
|
Address of manufacturer |
Bachtobelstrasse 3 8810 Horgen Switzerland |
|
Location of manufacturing sites |
Specialty Electronic Materials Switzerland GmbH site 1 Jiangsu FOPIA Chemicals Co., Ltd, Touzeng Village 224555 Binhuai Town, Binhai County, Yancheng City, Jiangsu, China Specialty Electronic Materials Switzerland GmbH site 2 Rohm and Haas (UK) Ltd. Tyneside Works, Ellison Street, NE32 3DJ Jarrow United Kingdom of Great Britain and Northern Ireland (the) |
|
Active substance |
C(M)IT/MIT (3:1) |
|
Name of manufacturer |
Thor GmbH |
|
Address of manufacturer |
Landwehrstraße 1 67346 Speyer Germany |
|
Location of manufacturing sites |
Thor GmbH site 1 Landwehrstraße 1 67346 Speyer Germany |
|
Active substance |
C(M)IT/MIT (3:1) |
|
Name of manufacturer |
Thor Quimicos de México, SA de CV |
|
Address of manufacturer |
Km 182 Autopista México – Querétaro, Pedro Escobedo 76700 Querétaro Mexico |
|
Location of manufacturing sites |
Thor Quimicos de México, SA de CV site 1 Km 182 Autopista México – Querétaro, Pedro Escobedo 76700 Querétaro Mexico |
|
Active substance |
C(M)IT/MIT (3:1) |
|
Name of manufacturer |
Troy Chemical Company BV |
|
Address of manufacturer |
Poortweg 4C 2612 Delft Netherlands (the) |
|
Location of manufacturing sites |
Troy Chemical Company BV site 1 Weifang Heaven-sent New Materials Technology Co. Ltd, Binhai Road, Changyi Coastal Economic Development Zone 261312 Weifang China Troy Chemical Company BV site 2 Dalian Xingyuan Chemistry Co., Ltd, Room 1205/1206, Pearl River International Building, No.99, Xinkai Road, Xigang District, Songmudao Chemical Industry Zone, Puwan New District 116308 Dalian China Troy Chemical Company BV site 3 Dalian Bio-Chem Company Limited, Songmudao Plant: Songmudao Chemical Industry, Zone, Puwan New District 116308 Dalian China |
|
Active substance |
C(M)IT/MIT (3:1) |
|
Name of manufacturer |
Jiangsu FOPIA Chemicals Co., Ltd |
|
Address of manufacturer |
Touzeng Village, Binhuai Town, Binhai County 224555 Yancheng City China |
|
Location of manufacturing sites |
Jiangsu FOPIA Chemicals Co., Ltd site 1 Touzeng Village, Binhuai Town, Binhai County 224555 Yancheng City China |
2. PRODUCT FAMILY COMPOSITION AND FORMULATION
2.1. Qualitative and quantitative information on the composition of the family
|
Common name |
IUPAC name |
Function |
CAS number |
EC number |
Content (%) |
|
C(M)IT/MIT (3:1) |
Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) |
active substance |
55965-84-9 |
|
2,2 - 20,9 % (w/w) |
2.2. Type(s) of formulation
|
Formulation type(s) |
AL Any other liquid |
PART II.
SECOND INFORMATION LEVEL - META SPC(S)
1. META SPC 1 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 1 identifier
|
Identifier |
Meta SPC: Meta SPC 3 |
1.2. Suffix to the authorisation number
|
Number |
1-1 |
1.3. Product type(s)
|
Product type(s) |
PT06: Preservatives for products during storage PT11: Preservatives for liquid-cooling and processing systems PT12: Slimicides |
2. META SPC 1 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 1
|
Common name |
IUPAC name |
Function |
CAS number |
EC number |
Content (%) |
|
C(M)IT/MIT (3:1) |
Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) |
active substance |
55965-84-9 |
|
2,2 - 6,5 % (w/w) |
2.2. Type(s) of formulation of the meta SPC 1
|
Formulation type(s) |
AL Any other liquid |
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 1
|
Hazard statements |
H332: Harmful if inhaled. H314: Causes severe skin burns and eye damage. H317: May cause an allergic skin reaction. H410: Very toxic to aquatic life with long lasting effects. H290: May be corrosive to metals. H302: Harmful if swallowed. EUH071: Corrosive to the respiratory tract. |
|
Precautionary statements |
P260: Do not breathe fume. P264: Wash skin thoroughly after handling. P270: Do not eat, drink or smoke when using this product. P272: Contaminated work clothing should not be allowed out of the workplace. P273: Avoid release to the environment. P280: Wear protective gloves/ protective clothing/ eye protection/ face protection/ hearing protection. P362+P364: Take off contaminated clothing and wash it before reuse. P333+P313: If skin irritation or rash occurs: Get medical advice. P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT induce vomiting. P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower]. P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing. P310: Immediately call a POISON CENTER/ doctor. P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P391: Collect spillage. P405: Store locked up. P234: Keep only in original packaging. P301+P312: IF SWALLOWED: Call a POISON CENTER/ doctor if you feel unwell. P406: Store in a a corrosion-resistant container with a resistant inner liner. P390: Absorb spillage to prevent material damage. |
4. AUTHORISED USE(S) OF THE META SPC
4.1. Use description
Table 1
Preservation of polymer lattices
|
Product type |
PT06: Preservatives for products during storage |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
|
Field(s) of use |
Indoor use Preservation of polymer latexes The biocidal product is recommended for the control of bacteria, yeast and fungi in the manufacture, storage, and transport of latexes, synthetic polymers including Hydrolysed Poly Acryl Amide (HPAM) and biopolymers (e.g. xanthan, dextran..) natural latexes. |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated application. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
|
Application rate(s) and frequency |
Application rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product. - Number and timing of application: The biocidal product is added at single dose at the time of manufacture, storage or shipment. To ensure uniform distribution, slowly disperse using automated metering or manual addition, into product with agitation. Mix thoroughly until evenly dispersed throughout the product. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product. For the biocidal product as supplied: for industrial use only. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.1.1. Use-specific instructions
4.1.2. Use-specific risk mitigation measures
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 2
Preservation of mineral slurries
|
Product type |
PT06: Preservatives for products during storage |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data |
|
Field(s) of use |
Indoor use Preservation of mineral slurries The biocidal product is recommended to control the growth of bacteria in aqueous-based inorganic/mineral slurries and inorganic pigments which are formulated into paints, coatings and paper. |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated application. The biocidal product should be dispensed as a tankside additive into the circulating use-dilution of the fluid, using a metering pump or by manual pouring, at a point to assure adequate mixing throughout the system. |
|
Application rate(s) and frequency |
Application rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product. - Number and timing of application: The biocidal product is added at single dose at the time of manufacture, storage or shipment. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product. For the biocidal product as supplied: for industrial use only. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.2.1. Use-specific instructions
4.2.2. Use-specific risk mitigation measures
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 3
Preservation of functional fluids (hydraulic fluids, antifreeze, corrosion inhibitors, etc. - excluding fuel additives)
|
Product type |
PT06: Preservatives for products during storage |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data |
|
Field(s) of use |
Indoor use Preservation of functional fluids (hydraulic fluids, antifreeze, corrosion inhibitors, etc. - excluding fuel additives) The biocidal product is recommended to control the growth of bacteria in functional fluids such as brake and hydraulic fluids, antifreeze additives, corrosion inhibitors, spinning fluids. The biocidal product inhibits the growth microorganisms, which would otherwise lead to odours formation, viscosity alteration, discolouration of product and premature product failure. |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated dosing. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
|
Application rate(s) and frequency |
Application rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: Add at a typical use rate between 6 to 30 mg C(M)IT/MIT (3:1) per kg final product to be treated. - Number and timing of application: The biocidal product is added at single dose at time of manufacturing, storage or shipment. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: Add at a typical use rate between 6 to 30 mg C(M)IT/MIT (3:1) per kg final product to be treated For the biocidal product as supplied: for industrial use only. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.3.1. Use-specific instructions
4.3.2. Use-specific risk mitigation measures
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 4
Preservation of liquids used in closed recirculating cooling systems
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria (including Legionella pneumophila) Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
|
Field(s) of use |
Indoor use Outdoor use Preservation of liquids used in closed recirculating cooling systems (Closed re-circulating cooling water systems comprise compressor cooling, air conditioning chilled water, boilers, engine jacket cooling, power supply cooling, and other industrial processes). The biocidal product is used to control the growth of aerobes and anaerobes bacteria, yeast, fungi, and biofilm in the circulating water of closed systems |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated dosing. |
|
Application rate(s) and frequency |
Application rate: Curative efficacy:- against bacteria (including L. pneumophila) at 5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours - against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours.- against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 48 hours. Preventive efficacy:- against bacteria (including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT (3:1) / m3 of water. - against biofilm (including L. pneumophila): 3 g C(M)IT/MIT (3:1) / m3 of water. - Number and timing of application: Curative efficacy: — against bacteria (including L. pneumophila) at 5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours — against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours — against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 48 hours Preventive efficacy: against bacteria (including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT (3:1) / m3 of water. against biofilm (including L. pneumophila): 3 g C(M)IT/MIT (3:1) / m3 of water. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.4.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.4.2. Use-specific risk mitigation measures
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 5
Preservation of liquids used in small open recirculating cooling systems
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria (including Legionella pneumophila) Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data Scientific name: no data Common name: Algae (green algae and cyanobacteria) Development stage: no data |
|
Field(s) of use |
Indoor use Outdoor use Preservation of liquids used in small open recirculating cooling systems (blowdown and recirculating flow rates, as well as total volume of water limited to 2 m3/h, and 100 m3/h and 300 m3 respectively) Process and cooling water: Used to control the growth of bacteria, algae, fungi and biofilm |
|
Application method(s) |
Method: open system Detailed description: Manual and automated dosing. |
|
Application rate(s) and frequency |
Application rate: Curative treatment Against bacteria (including L. pneumophila) at 5 – 14,9 g C(M)IT/MIT (3:1) / m3 of water, - against biofilm (including L. pneumophila) at 1,5 to 14,9 g C(M)IT/MIT (3:1) / m3 of water, - against fungi (including yeast) at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water. Preventive treatment: - Against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water, - against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water. - Number and timing of application: Curative treatment: — Against bacteria (including L. pneumophila) at 5 – 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 24 hours — against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 48 hours. — against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 48 hours. Preventive treatment: — against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water. — against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.5.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.5.2. Use-specific risk mitigation measures
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.6. Use description
Table 6
Preservation of liquids used in pasteurizers, conveyor belts and air washers
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria (including Legionella pneumophila) Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data Scientific name: no data Common name: Algae (green algae and cyanobacteria) Development stage: no data |
|
Field(s) of use |
Indoor use Outdoor use Preservation of liquids used in non-food pasteurizers and conveyor belts, air washers. |
|
Application method(s) |
Method: - Detailed description: The biocidal product is dosed automatically in the heat transfer fluid, in a place of good mixing (e.g. collecting sump below the conveyor belt). The feeding pipe is used to dose the biocidal product below the water level in order to limit its evaporation. |
|
Application rate(s) and frequency |
Application rate: Curative treatment: -against bacteria (including L. pneumophila): 5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water - against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water - against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water. Preventive treatment: Against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water, against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water. - Number and timing of application: Curative treatment: against bacteria (including L. pneumophila): 5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours — against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 48 hours. — against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 48 hours. Preventive treatment: — Against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water. — against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.6.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
Air washers: For use only in industrial air-washer systems that maintain effective mist eliminating components.
4.6.2. Use-specific risk mitigation measures
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.7. Use description
Table 7
Preservation of recirculating fluids used in textile and fiber processing, leather processing, photo-processing and fountain solution systems
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data |
|
Field(s) of use |
Indoor use Preservation of recirculating fluids used in textile, fiber processing, leather processing, photo-processing and fountain solution systems C(M)IT/MIT (3:1) biocidal products are used for the preservation of textile and spinning fluids, photo processing solutions, leather process (e.g. washing and soaking treatment stages) and printing fountain solutions to control the integrity of recirculating fluid by reducing microbial contamination in the bulk solution. |
|
Application method(s) |
Method: - Detailed description: Manual and automated dosing. The preservation of all end-products is performed in most cases highly automated by industrial users. The biocidal product is added to the central sump, basin or recirculating lines in an area with adequate mixing. |
|
Application rate(s) and frequency |
Application rate: Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1) per L of fluid - Number and timing of application: Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1) per L of fluid Contact time 5 days |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.7.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.7.2. Use-specific risk mitigation measures
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.8. Use description
Table 8
Preservation of re-circulating liquids used in paint spray booths and electrodeposition coating systems
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data |
|
Field(s) of use |
Indoor use Preservation of re-circulating liquids used in paint spray booths and electrodeposition coating systems. The biocidal product is used for preservation of fluids in pre- treatment processes (Cleaning treatment for grease removal and soil, degreasing Phosphating process, Rinse off tanks) paint spray booths and electrodeposition coating systems (e.g. cataphoretic baths) applied in Car Refinishing and Original equipment Car Manufacturing to control the integrity of recirculating fluid by reducing microbial contamination from bacteria and fungi in the bulk solution. |
|
Application method(s) |
Method: - Detailed description: - |
|
Application rate(s) and frequency |
Application rate: Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final product. - Number and timing of application: Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final product. The biocidal product is added at the time of manufacture, storage or shipment. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.8.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.8.2. Use-specific risk mitigation measures
4.8.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.8.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.8.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.9. Use description
Table 9
Preservation of liquids used in closed recirculating heating systems and associated pipework
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria (anaerobes and aerobes (including Legionella pneumophila) Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
|
Field(s) of use |
Indoor use Outdoor use Preservation of liquids used in closed recirculating heating systems and associated pipework. Pre-commission biocide flushing of new or existing pipework systems (heating and chilling pipework) includes used or new structural pipework built on industrial building projects. Closed recirculating heating systems: pre-commission biocidal product flushing of new or existing pipework systems (heating and chilling pipework) includes used or new structural pipework built on industrial building projects. The biocidal product is used to control the growth of aerobic and anaerobic bacteria, fungi and biofilm in the circulating water of closed systems. Closed systems are less susceptible to corrosion, scaling and biological fouling than open systems. However microbial problems can occur, if the system is left filled and untreated. This is due to the presence of nitrite and glycols used as nutrients by microbes. |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated dosing. The biocidal product is dosed automatically in the heat transfer fluid, in a place of good mixing. The feeding pipe must dose the biocidal product below the water level in order to limit the evaporation of the biocidal product. |
|
Application rate(s) and frequency |
Application rate: Curative treatment - against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L. pneumophila) - against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water - against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Preventive treatment - against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water - against biofilm at 3 g C(M)IT/MIT (3:1) / m3 of water. - Number and timing of application: Curative treatment: — against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L. pneumophila) Contact time: 24 hours — against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 24 hours — against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Contact time: 48 hours Preventive treatment — against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water and against biofilm at 3 g C(M)IT/MIT (3:1) / m3 of water. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.9.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.9.2. Use-specific risk mitigation measures
4.9.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.9.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.9.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.10. Use description
Table 10
Preservation of polymers used in oilfield processes (e.g. enhanced oil recovery, drilling muds, etc.)
|
Product type |
PT11: Preservatives for liquid-cooling and processing systems |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data |
|
Field(s) of use |
Outdoor use Preservation of polymers used in oilfield processes (e.g. enhanced oil recovery, drilling muds, etc.) |
|
Application method(s) |
Method: - Detailed description: - |
|
Application rate(s) and frequency |
Application rate: Preventive treatment of polymers used in the injection water: Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution. - Number and timing of application: Preventive treatment of polymers used in the injection water: Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.10.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.10.2. Use-specific risk mitigation measures
4.10.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.10.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.10.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.11. Use description
Table 11
Slimicide treatment in the de-inking process of the pulp and paper
|
Product type |
PT12: Slimicides |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
|
Field(s) of use |
Indoor use Slimicide treatment in the de-inking process of the pulp and paper. Recycling paper /deinking paper mills. Deinking process is a manufacturing paper process of removing printing inks from waste paper-fibers to produce deinked pulp. |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated dosing. The biocidal product is automatically dosed by pump and fixed pipes into the circuit, usually in the pulper below the water level. |
|
Application rate(s) and frequency |
Application rate: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. - Number and timing of application: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated Contact time: 24 hours Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.11.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.11.2. Use-specific risk mitigation measures
4.11.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.11.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.11.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.12. Use description
Table 12
Slimicide treatment in the wet-end stage of paper manufacturing process
|
Product type |
PT12: Slimicides |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
|
Field(s) of use |
Indoor use Slimicide treatment in the wet-end stage of the paper manufacturing process (paper mills, wet-end stage (water circuits), and paper mills process system). |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated dosing. |
|
Application rate(s) and frequency |
Application rate: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. - Number and timing of application: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated Contact time: 24 hours Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.12.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.12.2. Use-specific risk mitigation measures
curative treatments in plants connected to a slimicide-free water from a pulp mill and only for the treatment of the short circulation of the paper mill; and
preventive treatments,
4.12.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.12.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.12.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.13. Use description
Table 13
Preventive treatment (biofouling control) online and after cleaning in place for industrial RO/NF membranes
|
Product type |
PT12: Slimicides |
|
Where relevant, an exact description of the authorised use |
- |
|
Target organism(s) (including development stage) |
Scientific name: no data Common name: Bacteria Development stage: no data |
|
Field(s) of use |
Indoor use Preventive treatment (biofouling control) online and after cleaning in place for industrial RO/NF membranes |
|
Application method(s) |
Method: closed system Detailed description: Manual and automated dosing.Biocidal product application on a routine basis will prevent biofilm growth on Reverse Osmosis or Nano Filtration membrane surfaces, feed spacer, filter media and pipework. The biocidal product should be dispensed to the feed water at a point to assure adequate mixing throughout the system. |
|
Application rate(s) and frequency |
Application rate: Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid - Number and timing of application: Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid |
|
Category(ies) of users |
Industrial |
|
Pack sizes and packaging material |
For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
4.13.1. Use-specific instructions
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
4.13.2. Use-specific risk mitigation measures
4.13.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.13.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.13.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE OF THE META SPC 1
5.1. Instructions for use
PRECAUTIONARY MEASURES DURING STORAGE AND TRANSPORT:
Keep in a well-ventilated place. The product as supplied may evolve gas (largely carbon dioxide) slowly. To prevent the buildup of pressure the product is packaged in specially vented containers, where necessary. Keep this product in the original container when not in use. Container must be stored and transported in an upright position to prevent spilling the contents through the vent, where fitted.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
5.4. Instructions for safe disposal of the product and its packaging
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Conditions for safe storage, including any incompatibilities: Keep in a dry, cool and well-ventilated place, in the original container.
Shelf-life: 12 months
Protect from sunlight.
Recommendation: If a metal packaging is used, a varnish layer should be applied.
6. OTHER INFORMATION
-
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 1
7.1. Trade name(s), authorisation number and specific composition of each individual product
|
Trade name(s) |
Spectrum™ RX6804 MICROBIOCIDE |
Market area: EU |
|||||
|
Authorisation number |
|
EU-0025678-0001 1-1 |
|||||
|
Common name |
IUPAC name |
Function |
CAS number |
EC number |
Content (%) |
||
|
C(M)IT/MIT (3:1) |
Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) |
active substance |
55965-84-9 |
|
5,9 % (w/w) |
||
7.2. Trade name(s), authorisation number and specific composition of each individual product
|
Trade name(s) |
Spectrum™ PR3126 PRESERVATIVE |
Market area: EU |
|||||
|
Spectrum™ RX8560 MICROBIOCIDE |
Market area: EU |
||||||
|
Spectrum™ RX7827 MICROBIOCIDE |
Market area: EU |
||||||
|
Authorisation number |
|
EU-0025678-0002 1-1 |
|||||
|
Common name |
IUPAC name |
Function |
CAS number |
EC number |
Content (%) |
||
|
C(M)IT/MIT (3:1) |
Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) |
active substance |
55965-84-9 |
|
3,2 % (w/w) |
||
7.3. Trade name(s), authorisation number and specific composition of each individual product
|
Trade name(s) |
Biosperse™ 250 MICROBIOCIDE |
Market area: EU |
|||||
|
Biosperse™ 251 MICROBIOCIDE |
Market area: EU |
||||||
|
Biosperse™ 850 MICROBIOCIDE |
Market area: EU |
||||||
|
Biosperse™ 851 MICROBIOCIDE |
Market area: EU |
||||||
|
Spectrum™ RX6810 MICROBIOCIDE |
Market area: EU |
||||||
|
Spectrum™ RX6820 MICROBIOCIDE |
Market area: EU |
||||||
|
Authorisation number |
|
EU-0025678-0003 1-1 |
|||||
|
Common name |
IUPAC name |
Function |
CAS number |
EC number |
Content (%) |
||
|
C(M)IT/MIT (3:1) |
Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) |
active substance |
55965-84-9 |
|
2,3 % (w/w) |
||